Search Documents

By William A. Bassett

Two very intense sources of electromagnetic radiation are contributing significantly to experimental studies of minerals at high pressures and temperatures: 1) A Q-switched YAG laser is able to produce a pulse of infrared radiation capable of heating a sample under pressures up to 400 kbar in a diamond cell up to temperatures in excess of 4000°C. 2) X-rays from the Cornell High Energy Synchrotron Source (CHESS) are used to obtain diffraction patterns of samples In a diamond cell in less than two minutes, patterns that would require hundreds of hours on a conventional source. The laser heating technique is being used to study the pressure-temperature conditions over which the melting of diamond takes place. In the initial stages of this investigation, diamond has been melted and techniques for detecting the melting have been developed. The intense X-rays from the synchrotron source have been used to examine the mechanism and rate of the pressure-induced phase transformation in Fe2Si04.

Jan 1, 1985

By James Ruddy

THE medical program of the Climax Molybdenum Co. is under the supervision of the department of industrial medicine of the University of Colorado, of which James J. Waring, professor of medicine at the University Medical School, is director. Dr. Waring is consultant and direct supervisor of both the hospital and industrial medical department at Climax. At Climax the program is in charge of the medical director and the associate physician, Dr. Galen M. Hover. The hospital at Climax is completely equipped with all that is necessary for the practice of scientific medicine and surgery. Only graduate registered nurses with experience in industrial medicine are employed. Being only a few hundred yards from the portal of the mine. acci-

Jan 1, 1946

By T. A. Rickard

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes on, like some writers, talking about `the former' and `the latter', `he', `she', `it', and `they', through !clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a' feeble ending for a serious statement. How often do you hear `the former' and `the latter' in conversation? Good conversation is a guide not to be dis¬dained. When you must use `the latter', do not confuse it with `the last'. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is best. I "Partly prevented" is a poor phrase. `Prevented! is a word that does not lend itself readily to modification. He means `checked' or `corrected'.

Jan 1, 1931

By J. J. Jonas, J. L. Uvira

Equipment was constructed which permitted the hot compression of 99.8 pct Armco iron and 2.8 pct Si steel at constant true strain rates of 0.05 to 1 per sec over the temperature range 600" to 1000°C. A maximum true strain of 1.9 could be attained, followed by immediate quenching or by isothermal annealing. True stress-true strain curves were obtained, and the steady-state flout stress, a, strain rate, i, and temperature, T, were found to fit the following expression: The constants A, a, n', and AH were determined for the two ,materials. The activation energies obtained for Arrnco iron and silicon steel are 66 and 80 kcal per mole, respectively, and approximate those for seu- diffusion and for creep. This indicates that hot compression is a diffusion-controlled thermally activated process. THE hot compression of iron and steel is usually carried out in the austenite temperature range,1"7 as this is the one of greatest interest with respect to industrial hot working. However, a disadvantage of testing in the austenite range is that the hot-worked structure is destroyed by the phase transformations taking place during cooling. The present study was therefore carried out in the ferritic temperature range, and the hot-worked substructures were preserved by rapid quenching after deformation. The substructural results will be described in a separate paper, and the present communication is restricted to the strain rate/stress/temperature relationship observed during hot working. The results of hot-compression testing are usually given in the form of true stress/true strain curves, with a different curve for each temperature/strain rate ~ornbination.',~,~ Sometimes simple algebraic equations are fitted to the curves, so that certain extrapolations or interpolations can be performed.1'2'5 These equations are, however, devoid of mechanistic interpretations. The present study was undertaken to show that hot compression can be described by an equation of the type used in creep studies. That is, it will be shown that the temperature dependence of the strain rate in hot working is well-represented by an Arrhenius term, with an activation energy similar to that for creep. Also it will be seen that the stress dependence of the strain rate is similar to that for creep EXPERIMENTAL METHOD AND MATERIALS The investigation was carried out with the following three ferrous materials: 1) Armco iron; 2) Armco iron with 0.26 pct Mn; 3) 2.8 pct Si steel. The first two materials were utilized for investigations performed in the temperature range 600" to 800°C; the last one was used for tests at temperatures from 600" to 1000°C. The materials were of commercial purity,* as shown in Table I. Cylinders of five different sizes were prepared by strain annealing. The resulting mean grain diameter was 3 mm in the 1-in. Armco iron and 2 mm in the other sizes and grades. Different ratios of diameter/height were used to enable the determination of the coefficient of friction. The specimen faces were provided with concentric grooves, which acted as lubricant holders during compression, as recommended by English and ~ackofen' and others.2'9 Powdered glass lubricants were applied to the samples before hot compression to decrease friction and barreling, following the practice of previous investigator~.~~~~~~~~ Different mixtures of glass powder were used for each temperature, after the determination of suitable compositions by experiment.'' Equipment for Hot Compression. Hot-compression tests were carried out on an adapted 150-ton vertical hydraulic extrusion press and also on a modified high-temperature creep machine. The modified extrusion press was used for temperatures up to 800°C. The following items were added to the press: a) a high-temperature furnace with built-in upper and lower platens; and b) a transmission assembly, which permitted the attainment of logarithmically decreasing crosshead speeds. These accessories are described in detail in Ref. 11.

Jan 1, 1969

By J. W. Marx, R. H. Langenheim

The injection of heat-bearing fluids may offer a wider application to secondary and tertiary recovery from conventional oil reservoirs than inderground combustion since the process is more easily controlled and the reservoir requirements, in general, are less critical. In all cares, conduction heat losses to overburden and un-derburden will impose an economic limit upon the size of the area which can be swept out from any one injection point for any given set of conditions. The present report describes a method for c.rtin~ating thermal invasion rates, cumulative heated area, and theoretical economic limits for sustained hot-fluid injection at a constant rate into an idealized reservoir. Full allow-ance is made for non-productive reservoir heat losses. Required solutions can be obtained directly from the numerical tables given here, as soon as all operating conditions are specified, withou extensive mathematica1 ~nanipulation on the part of the user. The injection of a heat-bearing fluid into a reservoir is frequently proposed as a means of secondary or tertiary oil production. This form of thermal recovery may offer a wider application to conventional oil reservoirs than underground combustion since the process is more easily controlled and the reservoir requirements, in general, are less critical. Because of its large gross heat capacity, steam appears to be the most efficient heat injection medium, although mixtures of steam and other gases, hot water, hot oil and hot non-condensable gases also have been employed. Whatever the nature of the injection medium, economic evaluation of such thermal recovery processes will depend upon thermal invasion rates, or rates of productive reservoir heating, at any given time after the start of heat injection. In all cases, conduction heat losses to overburden and underburden will impose an economic limit upon the size of the area which can be swept out from any one injection point, for a given set of reservoir conditions, at any given heat injection rate. The present report describes a method for estimating thermal invasion rates, cumulative heated area and theoretical economic limits for sustained heat injection at a constant rate into an idealized reservoir, making full allowance for non-productive reservoir heat losses. Required solutions can be obtained directly from the nu- merical tables given here, as soon as all operating conditions are specified, without extensive mathematical manipulation. It should be noted that ordinary water flooding may be used to move an annular-heated zone outward, even though the economic areal limit for straight heat injection has been reached. Thus well spacing need not be confined to the areal limits as determined here. However, the present calculations do not cover such supplementary heat scavenging programs. The operating element consists of a radial flow system, concentric about the point of injection, with the idealized step function temperature profile illustrated by the dashed line in Fig. 1. The solid curve shown in Fig. 1 gives a qualitative picture of the true radial temperature distribution. It will be shown later that the expressions given below, which are derived from the simplifying step idealization (dashed line in Fig. I), also can be interpreted in terms of the more realistic temperature distribution shown in Fig. 2. For this case, the thermal invasion radius is simply redefined as the distance from injection well to the mid-point of the temperature distribution.

By Arthur S. Dwight

THE professional career of Thomas Septimus Austin, who died at El Paso, Tex., August 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., December 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Conn., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-office in Leadville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germanic bears the honorable distinction of being one of the first of the large " custom " lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smelting practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

By R. F. Burdyn

The inadequate use of centrifugation to economically recover solids from weighted drilling fluids reflects the need for better equipment and techniques for this putpose. Laboratory studies in the development of an improved separator are described in which an operating equation is derived and tested. Results show that the concentric cylinder geometry employed effectively separates bnrite from a suspension and that the operating equation provides a good approxinmtion for scale-up. INTRODUCTION Our current drilling technology frequently requires a high-density drilling fluid obtained by addition of barite. In the course of drilling, formation solids which are too fine to be removed either by screening or settling become suspended in the drilling fluid and gradually the volume of solids in the mud increases. The volume fraction of solids must be limited (if a satisfactory set of rheological parameters are to be maintained). A centrifugal separatorprovidesan economical way of accomplishing this. The barite recovery process can be considered as a separation of two solids. One, the light solids, composed of formation and added solids, has a specific gravity of 2.6 to 2.7; the other, barite, has a specific gravity of 4.2 to 4.3. This density difference, plus the fact that the average light-solids particle size is much smaller than the average barite particle size, permits separation by a centrifuge. In drilling fluids some of the coarse particles of the light-solids-range will settle faster than fine particles of the barite-particle range. As a result a complete separation of the two species is not possible. since the object of the process is not merely recovering the maximum amount of barite but includes as well removing the maximum amount of light solids, an optimum barite recovery efficiency exists. From a practical standpoint this optimum cannot be determined in the field for each drilling fluid system, and in practice the separation is less than optimum, with some sacrifice of barite. Drilling technology has included centrifugal separators for barite recovery for more than a decade. Results have been reported by a number of investigators indicating that the process is practical and economica1. l-4 The decision to use a centrifuge is based on economics in which direct cost savings and the indirect benefits in rig time derived from improvement of the drilling fluid are important factors. One would expect that centrifugal separation of barite from drilling fluids would significantly affect barite consumption; however, this is not the case. The Minerals Yearbook shows an annual domestic barite consumption in the drilling industry of nearly 1 million tons.5 By rough estimate there are perhaps 80 separators presently in field use. Assuming half of these in use at any one time, operating an average of four hours per day, at recovery rates averaging 3,000 Ib of barite per hour, total annual recovery is about 90,000 tons. This is less than 10 per cent of he total barite used. I conservatively estimate that barite consumption in drilling operations can be reduced by 30 per cent through greater utilization of centrifugal separators. To encourage more widespread acceptance of centrifugal separators in the drilling industry, improved equipment and techniques would be very desirable. The present paper, covering theory and results obtained from a laboratory model, is the first in a series on he development of an improved mud separator for field use. THE CONCENTRIC CYLINDER GEOMETRY AS A SEPARATING DEVICE Consider the geometry shown in Fig. 1, consisting of two concentric cylinders separated by an annular space. These are arranged so that the outer cylinder is fixed and the inner one can be rotated about its axis on shafts sealed against the ends of the outer cylinder. If the outer cylinder is fitted with openings at either end, the inner

Jan 1, 1966

By E. R. Macgregor, J. Halpern

The kinetics of the reduction of cupric salts in aqueous solution by molecular hydrogen to metallic copper are described. The rate of reduction appears to be homogeneously determined and shows a marked inverse dependence on the hydrogen-ion concentration. Precipitation of copper is more rapid and complete in sulfate than in per-chlorate solution. A mechanism is proposed which accounts for this behavior. IN recent years a number of important hydro-metallurgical processes have been developed in which metallic salts in aqueous solution are reduced by gaseous hydrogen, usually at elevated temperatures and pressures, and thereby precipitated either in metallic form (e.g. Ni, Co, Cu) or as an oxide or salt of lower valence (e.g. VO, and VA).1 ; In connection with applications such as these, most of which involve heterogeneously catalyzed reactions, recent demonstrations"-" that salts of certain metals, e.g., Cu", Ag' , Hg" , and Hg,+ can activate molecular hydrogen homogeneously and thus catalyze hydrogenation reactions in aqueous solution, are of considerable interest. For example, cupric salts catalyze the otherwise slow homogeneous reduction of dichromate and ceric salts by hydrogen, i.e. Cr,O; + 3HL. + 8H1 ? 2Cr'- -- 7H,O [1] 2Ce ' ! H.. ? 2Ce" | 2H . [2] In perchloric-acid solution, where Cu" is not appreciably complexed, the kinetics have been found" " to be of the form -d [H,] _- k,[HJ [CU"]' dt -LCu+' l+ (k ,/k,) [H] [3] where, K = 1x10"' exp [—26,600/RT] 1, mole-' min-' ... [4] and (k ,/k,) - 0.25 at 110°C. This kinetic behavior suggests that the reaction proceeds by a mechanism involving the following sequence of steps kt Cu" +H1CuH' 4-HA [51 k., CUH + CU" ? + 2Cu f H' [GI 6Cu'+ Cr,07 + 14H'+ 2Cr- (¦ 7H,O + 6Cu" ['i] fast The catalytic activities of the undissociated cupric-sulphate and cupric-acetate complexes are somewhat greater (by factors of 6.5 and 120, respectively) than that of the simple hydrated Cu" ion.'" These considerations suggest that, in contrast to the other hydrometallurgical hydrogenation reactions, referred to previously, reduction of cupric salts in aqueous solutions by molecular hydrogen, should proceed homogeneously, and in the absence of an extraneous catalyst. This has already been demonstrated" for acetate-buffered solutions where the product of the reaction is a precipitate of cuprous oxide (Cu,O). In the present paper, an investigation of the reduction of cupric salts in perchloric-acid and sulphuric-acid solutions, leading to the precipitation of metallic copper, is described. Some results for the sulphate system, which is of considerable hydrometallurgical interest, have been reported previously by Ipatieff",' " and by Schaufel-berger' but these do not give a quantitative account, of the kinetics and mechanism of the reaction. Experimental The reduction experiments were conducted in the 1-gal, titanium-lined autoclave described in connection with earlier related investigations," " and using a similar procedure. The solutions were made up by dissolving known amounts of CP grade Cu(ClO,), and HC10, (or CuSO, and HISO,) in dis-tilled water. While in the autoclave, the solution was stirred and maintained at a constant temperature (±loc) and under a constant partial pressure of hydrogen gas. It was ascertained that the agitation (provided by two 3-in., four-bladed stirrers, rotating at 900 rpm) was adequate so that at no time was the rate of reaction limited by solution of hydrogen. During each experiment, samples of the solution were withdrawn periodically, allowed to cool, and the concentration of copper remaining in solution was then determined electrolytically. Some Cu' is formed during the reaction, but undergoes disproportionation when the solution is cooled to room temperature. For purposes of kinetic calcula-

Jan 1, 1959

By G. R. Love, M. L. Picklesirner

THE use of color adds a new beauty, power, and versatility to metallography. This has been amply demonstrated in a number of public exhibits and on the walls of corporate, government, and university metallographic laboratories around the world. Indeed, in a number of cases, the color not only is of esthetic value but is scientifically essential to the competent examination of particular samples and systems. Optical strain analysis,' determination of true grain size in U-A1 alloys: phase identification in Nb-base alloys,3 analysis of transformation rates in heat-treated Nb-Zr alloys,4 measurement of solidification segregation in cast Nb-Zr alloys,' study of the intermediate phases in Nb/Sn diffusion couples,6 investigation of the oxidation kinetics at various surface orientations in single crystals,7'8 and a number of other research efforts9'10 would have been vastly more difficult without the extra clarity and distinction introduced by color—either the colors resulting from particular polarized light techniques or the interference colors obtained by oxidation. It is unfortunate that the beauty of colored micro-structures cannot be shared more widely, but the economics of publishing a technical magazine apparently prohibits color plates except under extraordinary circumstances. It is doubly unfortunate that no convenient, general method exists for communicating the information available in colored microstructures to the scientific community. True, in some instances the color changes observed are dramatic enough that direct black and white photography is adequate. In photoelastic stress analysis, several orders of interference fringes may be produced and it is frequently desirable to suppress the color effects (use monochromatic light) to simplify interpretation. On the other hand, relatively minute color variations may be readily detectable by eye, be of considerable assistance in interpreting a structure, and yet be enormously difficult to reduce to an unambiguous black and white print. In order to illustrate a possible compromise or solution to the above problems, we wish to show three black and white photographs of the same region of an Nb/Sn diffusion couple whose interpretation depends heavily upon use of color techniques. These micro-structures were obtained from a section through a rod consisting of commercial-purity niobium tubing filled with 99.995 pct Sn (melt-filled in 10"6 Torr vacuum). The composite rod, measuring 500 mm long, was bent into a hairpin shape and inserted into water-cooled copper grips in a vacuum high-temperature furnace. The rod was outgassed for 2 hr at a furnace temperature of 800°C and was further heated by self-resistance using a 2.2-kva ac power supply. The rod was raised to 1910°C over a 4+-hr period, held for 15 min, slow-cooled to 1500°C over a -hr period, and free-cooled to room temperature (all temperatures were measured with W5Re/W26Re thermocouple). Throughout the heat treatment the ambient pressure was kept below 8 x lo-' Torr. Metallographic preparation of the sample was completely conventional except that it was necessary to extend the grinding steps to remove damage in the brittle NbsSn phase introduced by sectioning. No satisfactory chemical or electrochemical etch has been found for these diffusion couples; of those which have been tried, any that attack the niobium-rich phases at all attack the tin-rich phases disastrously. However, the final polishing steps did produce a slight relief effect and this, coupled with anodizing, yielded excellent clarity in the microstructures for direct observation. The anodizing voltage was chosen to give maximum change in color per unit change in composition. In this case, indeed normally, this maximum sensitivity occurred in the blue-to-red color range. The pure niobium tube wall anodized to a relatively bright blue

Jan 1, 1967

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By J. L. Brimhall, R. A. Huggins, M. J. Klein

IN a recent paper1 it was shown that small additions of magnesium, copper, and oxygen decrease the stacking fault probability in plastically deformed silver. Correlation of :X-ray data with measurements of the twinning frequency and metallographic observation of slip lines indicated that this effect may be due to an increase in the relative stacking fault energy. It is the purpose of the present note to report experiments on these alloys of known stacking fault probability that relate to the stacking fault contribution to electron scattering in silver. There has been a considerable amount of disagreement in the literature concerning the contribution of dislocations to electrical resistivity in metals. Calculations relating to the scattering of conduction electrons by the dislocation core, its strain fields, and related effects have been made by several authors.2-5 In addition, experimental work on Cu,3,6-10 Ni,11 and Ni-Co alloys1:! has shown that dislocations in those materials exert an anomalously large effect on resistivity, this effect being related to the presence of extended dislocations. The problem of the scattering due to the stacking fault region between partial dislocations has been treated theoretically using several different procedures.13-'0 The results of these calculations show a wide range of predicted values, from rather large to completely negligible, due to the models and the approximations involved. Almost all of this work has been applied to the specific problem of scattering in copper. The more complete theoretical treatments depend rather critically. on the shape of the Fermi surfaces and the effective mass parameters. The scattering from stacking faults might therefore be expected to vary significantly from one metal to another. Unfortunately, sufficiently accurate information is not available .which would allow one to have any confidence in a theoretical prediction of the scattering in the case of silver. Resistivity measurements were made on small wire specimens of vacuum melted high purity silver and several dilute alloys. These measurements were made at approximately 20°C, with great care being given to temperature measurement and corrections. At such temperatures phonon scattering is significantly greater than imperfection scattering. However, the experimental technique was such that measurements on similarly treated samples were reproducible to better than 2.4 X 10-9 ohm-cm, which was satisfactory for this work. Values of the stacking fault probability and the increase in resistivity after severe plastic deformation are given in Table I. The increases in resistivity resulting from plastic deformation agree quite well with previous work on silver.14,21-26 In addition, it has been previously found that interetitials and vacancies in silver anneal out well below room temperature, so that the residual imperfection scattering in these experiments could be expected to be primarily associated with dislocations;. It is seen from the data in Table I that large changes in stacking fault probability are accompanied by differences in resistivity due to imperfection scattering of only a few percent. If the scattering of conduction electrons by extended dislocations is primarily due to the area of the stacking fault region independent of the stacking fault energy, and not the core and strain fields associated with partial dislocations, the resistivity increase should be proportional to the product of the dislocation density and the stacking fault width, as is the stacking fault probability. Therefore, the imperfection scattering caused by plastic deformation of the alloys should be considerably smaller than that found in the pure silver. Since this was not observed, these results sugegest the possibility that stacking faults do not themselves contribute appreciably to the electrical resistivity of silver deformed at room temperature. An alternative explanation of these observations is that the scattering by the stacking fault is roughly proportional to the stacking fault energy, rather than being determined by the total area of such faults. Sufficient evidence is not yet available to separate these two possibilities. This work was supported by the Office of Naval Research.

Jan 1, 1962

By E. A. Hopkin

Laboratory tests conducted by the author. together with actual field experience in Canada. have indicated the magnitudc of some of the factors affecting ability of drilling mud to clean the hole. A correlation was observed between funnel viscosity and particle slip velocity. A relationship was also observed between the Bingham yield value of the mud and the particle .slip velocity. Laburatury tests indicated little change in slip velocity with funnel viscosities up to ahout 80 sec/qt or to yield values of aboul 15 lb/100 .sq ft. The lip velocity of the partic1e.s. studied vuried from 160 ft/min with water to neerly zero for high mud viscositie. lncreasing the mud density, creating laminar annular mud flow or rotating the drill pipe Mlay also improve the carrying capacity of mud. Field tests indicated that during fast upper-hole drilling, the rate of cutting removal must he sufficien to maintain the concentration of cuttings in the annulus at less than 5 percent by volume to prevernt balled-up drill collars and .stuck drill pipe. INTRODUCTION In the Mid-Continent area, hole cleaning during rotary drilling normally involves the use of low-density drilling muds with funnel viscosities varying from 26 to 80 sec/qt. However, frequently it is necessary to raise the mud viscosity in excess of 200 sec/qt to clean the hole. In addition, field experience has indicated that during very fast upper-hole drilling, annular mud velocities considerably in excess of the maximum slip velocity of the cuttings (normally considered to be 120 to 150 ft/min) are necessary to prevent balling the bit and drill collars. In view of these variations in mud properties and circulation rates necessary to clean the wellbore, a study of factors affecting hole cleaning and the relative magnitude of each was undertaken. The study was also prompted by the knowledge that a drilling mud with properties close to those of water would drill at rates several times that of a viscous mud. The carrying capacity of these near-water muds was not clearly understood, however, and many drillers were reluctant to use them. DISCUSSION EFFECT OF MUD PROPERTIES ON DRILLING RATE The effect of mud properties on drilling rate has been studied by a number of investigators. 1t is clear from their work that mud properties close to those of water will significantly improve drilling rate and bit life. If the water-type mud will also effectively clean the hole and cause no logging or formation impairment problems, the choice of an appropriate drilling fluid is clear—use water. Often, however, a water-type drilling fluid is not capable of effectively cleaning the hole. THEORY OF PARTICLE SETTLING The forces acting on a particle that is allowed to settle through a fluid quickly reach equilibrium, and the particle settles at some constant velocity referred to as the slip velocity. The slip velocity of any particle depends upon a number of factors such as density and viscosity of the fluid, the volume, specific gravity, shape and roughness of the particle, and upon the shape and area of the projected face of the particle at right angles to the direction of relative fluid solid movement. Brown' expressed this relationship for spheres in Newtonian fluids in the following equation. where v, = slip velocity D, — diameter of sphere p, = density of spheye p, = density of liquid /a = friction factor g = constant. The friction factor f, varies as the size, shape, surface roughness and slip velocity of the body, and as the density and viscosity of the fluid varies. WaddelV ound experimentally that where dynamic similarity exists. f, was a function of the particle Reynolds number (NRe) of the sphere (Fig. 1). Fig. 1 shows that f, for spheres varies from over 10 for low NKe numbers to 0.44 for N,,. over 600.

By AIME

DURING the Revolutionary War an iron mining industry was born in the Adirondack region of New York State. New York State ores provided the iron from which were forged the links of the chain that, strung across the Hudson River, successfully kept British vessels from ascending. The industry flourished for a while and then became dormant. For the successful prosecution of World War II, the magnetite mines were revived and given considerable aid in the form of government financial support. The complete story appeared in a special issue Of MINING AND METALLURGY published in November 1943. Now, almost four years later, it is interesting to see that these "war babies" were not really such but are well-established enterprises with a bright future. A ten-day trip through the Adirondack region and to St. Lawrence County dispelled all thoughts that mining in northern New York State is a transitory industry. In addition to substan-

Jan 1, 1947

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By J. O. Brittain, E. P. Lautenschlager, D. A. Kiewit

Compression tests were run in the temperature range of 700° to 900°C ox 0' phase NiAl intermetal-lic alloys of several grain sizes. At these temperatures the minimum strengths were observed at the stoichiometric composition. While significant increases in strength occurved in both the low-nickel (vacancy) and high-nickel (substitutional) regions, the highest strengths were found in the high-nickel region. During deformation serrated flow was sometimes observed in the low-nickel alloys. After deformation transgranular cvacking and deformation striations were observed in all compositions tested. AS part of a general investigation of the properties of NiAl inter metallic compounds, a preliminary study of the role of point defects upon plasticity was made by high-temperature compression tests on ß' NiAl specimens of several grain sizes and compositions. ß' NiAl is an intermetallic compound having a CsCl structure and a rather wide range of composition from A1-45 at. pct to 60 at. pct Ni.1 According to Bradley and Taylor2 and to cooper,' it possesses a defect lattice in which departures from stoichiometry in the direction of decreased nickel content lead to the presence of vacant nickel sites (although Cooper's work indicates that a small amount of substitution also occurs) whereas departures on the high-nickel side lead to substitution of nickel on aluminum sites. NiAl forms congru-ently from the melt at approximately 1650°C,1 and thus has a higher melting point than either of its component elements. Up to this time, although this and other high-melting intermetallic compounds have been suggested for elevated-temperature usage,4 only the hardness4 and a few tensile-strength measurements5 have been reported for NiAl at high temperatures. In the present investigation the effects of composition upon the compressive-strength properties in a range of 700° to 900°C have been measured for NiAl of several grain sizes. EXPERIMENTAL PROCEDURES The alloys were made as described elsewhere6 from an A1-46.8 at. pct Ni master alloy furnished by the International Nickel Co. with additions of high-purity nickel and aluminum. The charges were vacuum-induction-melted in A12O3 crucibles with small amounts of helium added to the atmosphere to suppress vaporization. They were cooled slowly from the melting temperature to achieve uniform grain size. In order to refine the as-grown grain size a special rolling technique was developed. Alloys were packed into 0.10-in. wall-type 302 stainless-steel tubes which were partially filled with magnesium oxide to prevent bonding between the alloy and the steel jacket. The ends of the tubes were closed by hot forging, and the packets were then hot-rolled. The alloys with greater than 50 at. pct Ni were rolled at 1100°C, but it was found necessary to increase the temperature to 1350° C before alloys with less than 50 at. pct Ni would roll without cracking. With these temperatures, reductions as high as 48 pct were achieved in a single pass. The rolled alloys will hereafter be referred to as "fine grained" whereas the as-grown material will be designated "coarse-grained''. The compression specimens were made by cutting square cross-sectional pieces, approximately 3/16 by 3/16 by 1/2 in., with a water-cooled diamond cut-off wheel from the as-grown or the rolled alloys. Specimens were ground to their final dimensions by polishing through 3/0 grit silicon carbide papers. The final shape was a rectangular parallelepiped of square cross section having a height-to-width ratio of 3:1. Compression testing was carried out in a compression rig of our own design mounted on an In-stron Floor Model. The specimen chamber could be heated to 1000°C and was controlled within ±2°C. The compression rig was enclosed within a bell jar and was maintained at a 50 µ of mercury vacuum throughout the duration of the test. The test cham -ber was heated from room to test temperature within 15 min. Specimens were then held at the test temperature 30 min prior to testing. Previous experiments indicated that no grain growth would occur within this time. An Instron Variable Crosshead speed unit was used to adjust for small variations in specimen lengths in order to have a constant initial strain rate, €, for all specimens of a group. For the fine-grained specimens the strain rate was changed rapidly at constant temperature by a factor of 10 with the speed lever on the Instron. For a given € the compression data was analyzed in terms of true plastic strain (E) and true compressive stress (0).

Jan 1, 1965

By C. E. Lawall

WHEN this study was started very little information was available, regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to properly classify West Virginia coals.

Jan 1, 1932

By M. J. Pool, P. J. Spencer, R. V. Miner

The partial molar heat of solution of rhodiunz in liquid lin and Rh-Sn alloys has been measured as a function of rhodium concentration at 700" , 725" , 750" , and 775°K. The values at infinite dilution are very exo thermic, ranging from -29,950 to -28,260 cal per g-atom Rh at 700" and 775"K, respectively. At the solubility limit the heat of solution becomes sharply nzore exothermic and has permitted the liquidus boundary to be accurately established at each temperature. From the measurements in the two-phase region of liquid Plus RhSn, the heat of formation of RhSn,has been determined. A large increase in the heat of formation between 725" and 750°K suggests the possibility of a phase transformation in this compound. V ERY few measurements have been made of the heats of solution of transition metals in liquid tin; yet those values that are available are of great interest because of their very large exothermic nature. For example, the heat of solution at infinite dilution of palladium in tin has been measured as about -26,000 cal per g-atom (625" to 800°~),' while the heat of solution at infinite dilution of platinum is even more exothermic at -28,591 cal per g-atom (914°K).' These values are of the same order of magnitude as the heat of formation of many intermetallic compounds and as such clearly indicate that very strong bonding must exist between the solute and tin atoms in the liquid solutions. Rhodium might be expected to display similar solution characteristics in tin in view of its close electronic resemblance to palladium and platinum. Since no thermodynamic data are available for Rh-Sn alloys, rhodium was chosen as an appropriate solute for further investigation of transition-metal systems with highly exothermic heats of solution at infinite dilution. EXPERIMENTAL The heat of solution of rhodium in dilute Rh-Sn liquid solutions was measured as a functlon of rhodium concentration at 700°, 725", 750°, and 775°K. The liquid-metal solution calorimeter used in this work has been fully described elsewhere. At the start of each series of measurements, the solvent bath consisted of about 0.5 g-atoms of 99.9+ pct pure tin. To this was made a number of small rhodium additions, about 0.0005 g-atoms each, and the heat of solution was measured for each. Rhodium of 99.9+ pct purity in powder form was used in order to promote rapid dissolution in the liquid tin. The powder specimens were contained in tin foil stated to be purified (lead-free). This foil was found to have no measurable heat of solution in pure tin so the effect of any impurities could be neglected. The energy equivalent of the calorimeter was experi- mentally determined by dropping tungsten and/or tin specimens at intervals during each series of rhodium drops. The tungsten and tin used were 99.95 and 99.999+ pct pure, respectively. The only heat effect due to a tungsten drop, or a tin drop at low rhodium concentrations in the bath, is the sensible heat of the specimen. The heat content of these materials is well-established and is presented in the compilation of Hultgren et al. 4 As the rhodium concentration in the tin bath increases a small heat effect arises from the reaction: Sn (liquid, T) — & (soln, T) where T is the temperature of the tin bath. Where necessary, this heat of solution of tin was determined by Gibbs-Duhem integration, and corrections were made to the heat effect of the tin calibration specimens and the tin foil containing the rhodium specimens. RESULTS AND DISCUSSION The calculated values of the heat of solution of rhodium in dilute Rh-Sn alloys as a function of composition are shown graphically in Fig. 1. The values have been corrected for the sensible heat of the specimens, initially at 273"K, and apply to the reaction:

Jan 1, 1969

By BARONJUPTNER VON JONSTORFF, Andrew A. Blair, GUNNAR DILLNER

IT is a well-known fact that the results of different analysts, when operating on the same identical sample of steel or iron, are far from concordant, and it not infrequently happens that great annoyance and trouble in the commercial community are occasioned by these discrepancies. Attempts have been made at various times to investigate the causes of such differences and to obtain more reliable methods of analysis. The most important of these was made by the British Association in 1889: The following gentlemen, with Sir W. Roberts-Austen as Chairman, and Professor T. Turner as Secretary, were constituted as a committee to investigate the question, viz.: Sir F. A. Abel, Mr. Edward Riley, Mr. G. J. Snelus, Mr. John Spiller, Professor J. W. Langley, and Professor Tilden. Average .samples of steel were prepared in America under the superintendence of Professor J. W. Langley. The steels, in the form of turnings, were divided and distributed to sub-committees in Great Britain, America, France, Germany, and Sweden. In Sweden Professor Åkerman acted as Secretary to the Swedish committee. The Government Department of Tests was appointed in Germany; Mr. Ferd. Gautier in France; the British Association Committee in England; Messrs. William

Mar 1, 1905

By David C. Jonson, W. Bruce MacKenzie, Arthur A. Bookstrom, Vaughn E. Surface, Neil K. Muncaster, Stewart R. Wallace

In mid-Tertiary time a wet silici-alkalic magma penetrated the Precambrian rocks of what is now the Tenmile Range of Central Colorado and formed the Climax Stock. The stock is a composite one and was intruded in four separate irruptions, each giving rise to a major hydrothermal event. The first three of these produced large stockwork ore bodies that cap and flank the tops of their respective source intrusives; the fourth, and last, yielded almost no commercial mineralization. The ore bodies and their related zones of alteration are circular to ring-shaped in plan and arcuate in section. The different phases of the stock are so positioned with respect to each other that many of the circular and arcuate zones of mineralization and alteration overlap or are juxtaposed. Evidence of a time separation between the different ore bodies is found in certain dikes that were intruded between periods of mineralization and are well mineralized in one ore body but are barren in another. If it is assumed that the parent magma at Climax contained 10 per cent "water," that the "water" contained 0.1 grams per liter of molybdenum, and that the processes of extraction were 100 per cent efficient, then approximately 10 cubic miles of magma would be required for the formation of each ore body. The volume requirements, taken in conjunction with the cross-sectional areas of the different phases of the stock to explored depths, suggest to the authors that each magma chamber was columnar, extended to a depth of thousands of feet, and was connected with a much larger master reservoir. The repetition of similar intrusive, structural, and hydrothermal events, indicates periodic tapping of this reservoir. A regular chemical evolution of the parent magma is suggested by the systematic change in metal ratios and differences in the sites of deposition, relative to the source intrusive, in each of the four separate igneous hydrothermal stages. The preparation of ground was due to changes in magmatic and/ or hydrothermal pressures within the igneous-hydrothermal columns; small, repeated, up and down movements of the rock enclosing the tops of the columns formed the stockwork fractures into which the mineralizers penetrated. The forceful emplacement of each successive phase of the Climax Stock resulted in a slight doming and rotation to the westward of the earlier-formed geologic features. Postore normal displacement along the Mosquito fault is estimated at about 9000 feet. Part of one ore body was cut by the fault and lies at depth below the Paleozoic sedimentary strata on the hanging wall. On the footwall side of the fault, subaerial erosion and glaciation removed a large part of one ore body and uncovered the top of a second.

Jan 1, 1968

By John V. Beall

Probably it won't happen to us again in a thousand years, but it was very embarassing at the time. It is only because of certain matters that have come up this month that we tell you at all about it. At the beginning of our trip to Peru and Chile last summer, we were flying with Bill Haddon from Lima to Tacna aboard Fawcett. Being an old hand at foreign travel, particularly in South America, we felt obliged to explain some of the special features of travel in Latin America and the niceties of etiquette in particular and were so engaged when the plane landed at the airport. We led the way briskly into the terminal, expecting at any moment to have a representative of Southern Peru Copper pop up and present himself. However, this didn't happen so we repaired to the baggage arrival station to wait. All the bags were quickly picked up, but ours were no where to be seen. Bill was slightly agitated because the plane was being buttoned up for take off. However, rising to the emergency with our usual aplomb, we took charge of the situation. Brandishing the claim checks under the nose of the porter who pointed to them and said, "si, Tacna," we nodded briskly and in our serviceable Spanish said "si se[n]or, vayase viejo, rapido." He was off and back with our suitcases quickly enough.

Jan 1, 1970