Search Documents

By E. S. Bartlett, D. N. Williams

QUANTITATIVE values for the oxidation rate of unalloyed molybdenum in air at temperatures above the melting point (1460°F) of the characteristic oxide are contained in the literature as a result of previous investigations. Lustman' reported values corresponding to 0.36 in. penetration per day (IPD) at 1500 and 1600°F in still air, noting essentially no variation in rate with temperature. Jones, Spretnak, and Speiser' reported values corresponding to 0.14 and 0.13 IPD at 1500 and 1800°F, respectively, in still air, attributing the decreased oxidation rate at higher temperatures to a lesser accumulation of the corrosive molten oxide on the surface at the higher temperature as a result of increased volatilization rate. Harwood3 ecently summarized work in the field, presenting generalized data corresponding to 0.48 to 0.96 IPD at 1800°F and 0.55 to 0.83 IPD at 1700°F in slowly flowing air. In a recent program at Battelle, it became desirable to know more about the characteristic oxidation behavior of molybdenum under varying conditions of temperature and atmosphere. Using oxidation-test apparatus designed for dynamic, continuous recording of weight change during testing,' values for the oxidation rate of molybdenum were obtained at temperatures from 1400 to 2150°F. In addition the effect of air flow on the oxidation rate was studied briefly at temperatures of 1600, 1800, and 2000°F. Exhaust of the contaminated atmosphere from the oxidation chamber was effected by an impeller pump attached to a 3/16-in.-diam opening in the oxidation chamber. The volumetric exhaust rate (cubic feet per hour) was normally maintained slightly in excess of the input rate to avoid condensation of MOO,,' on the sample suspension rod. The entering atmosphere was preheated prior to admission to the oxidation chamber by a 1 1/2-in.-diam cup packed with shredded asbestos. The experimental data are presented in Table I. Comparing conditions 2 and 3 (taking into account the temperature difference) and conditions 8 and 9. shows that in the absence of forced exhaust an atmosphere of moving air results in greater oxidation rate than a stagnant atmosphere. The use of forced exhaust, as shown by comparing conditions 3 and 4 and conditions 14 and 15: resulted in an even greater increase in oxidation rate. By virtue of the size of the atmosphere input and exhaust openings, it was calculated that the exhaust velocity was about 60 times that of the input velocity for essentially equal volumetric flow rates. Because of the proximity (about 3/4 in.) of the exhaust port to the specimen, it is logical to assume that cleansing of the atmosphere immediately surrounding the specimen was accomplished much more efficiently by the exhaust flow than by the input flow at a constant-volumetric flow rate. Also, it can be seen by comparing conditions 4 through 7 and conditions 11 through 13 that increasing the rate of atmosphere flow (by increasing input velocity with a proportional increase in exhaust velocity) above some optimum value has little, if any, further effect on the oxidation rate. These results suggest that there is a maximum oxidation rate for molydenum at a given temperature which is obtained when conditions are maintained such that the partial pressure of MOO3 in the atmosphere surrounding the specimen is at a low value. By controlling the partial pressure of MOO, surrounding the sample, it is possible to control the rate of volatilization of MOO:, from the surface. This, in turn, affects the rate of oxidation, since the thickness of the MOO3 layer determines the amount of oxygen which will be able to reach the reaction surface.' When the liquid oxide layer is less than some critical thickness, i.e., when the volatilization rate is high, enough oxygen is transported to the active surface to permit oxidation to proceed at the maximum rate allowed by the kinetics of the oxidation reaction. However, if the volatilization of MOO,, is suppressed, the thickness of the layer of MOO3 on the surface increases, and the diffusion of oxygen through the oxide layer becomes the rate-controlling step in the oxidation process. The lack of agreement between the present results and those of previous investigators is presumed to be due to differences in removal of the oxidation product (Moo,) from the immediate vicinity of the sample. By comparing conditions 1, 5, 10, 12 and 14, it is seen that when forced exhaust was used the oxidation rate of molybdenum increased with increasing temperature. A rapid increase was observed between 1400 and 1600°F, attributable to the effects

Jan 1, 1959

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962

By T. W. Martin, T. J. Crocker, J. M. Goris

The current technology of large rock conveyors is reviewed. Based on this investigation two large rock conveyor concepts have been developed and a test facility investigation designed and fabricated. The USBM will test these concepts along with loading and transfer points for handling mine run rock material up to 1.5 m (4.9 ft) in size. An evaluation of open pit mining systems using large rock conveyors documents substantial cost savings when compared to truck haulage.

Jan 1, 1983

By A. Phillips, H. J. Fisher

The influence of temperature and composition on the viscosity of high-purity liquid metals and alloys of the Pb-Sn and Sb-Cd systems was investigated by the logarithmic-decrement method. The variation of viscosity with temperature above the liquidus followed the equation: n = AeE/RT No large increase in viscosity was found just before normal freezing of any of the metals or alloys investigated. Certain alloys, supercooled below their stable liquidus, however, did show a marked increase in viscosity. Experimental activation energies for viscosity were determined for the metals investigated. Liquid-metal density values were obtained by a modified Joeger's method. IK an investigation of the properties of molten metals, the study of viscosity as a suitable means for studying the physical nature of the metallic liquid state has been utilized. Although interest in the relationship of the liquid to the solid-metal state holds promise of broadening the knowledge of metals in general, much information that is available regarding the influence of temperature and composition on viscosity, especially near the freezing point, is still controversial. The purpose of this paper is to present the results of recent work on this subject. Although interest in factors influencing the fluid behavior of metals and alloys has arisen from theoretical as well as applied studies of liquid-metal properties, the development of a comprehensive theory of the mechanism of viscosity has been handicapped because so little is known about the liquid state. Several theories of viscosity have been proposed and among the more recent are those of Andrade,1 Bernal,2 Frenkel,3 Eyring,4 and Gutmann and Simmons.5 Athough these contributions have helped to establish a basis of approach for studying the nature of viscosity, the fundamental aspects of the variation of viscosity with alloy composition have, in general, been neglected. Experimental Metals and Alloys Investigated: The Pb-Sn and Sb-Cd alloy systems were selected for investigation because they form constitutional features of theo-

Jan 1, 1955

By Persifor Frazer

I DESIRE to say that, owing to the number of papers which have been more or less crowded at this session of the Institute, and the fact that, as one of the Local Committee, I have the distinguished honor to feel somewhat like one of the hosts, I should not tax the patience of members at this late hour, but would have my paper read by title were it in any way possible to do this. But the task I have set myself this evening is to present to the eyes of the members of the Institute certain objects which have occupied more or less of my time during the last eighteen months or two years. The objects I allude to are some of the igneous rocks of this country, which, until quite recently, have been less understood than any others. It will be well known to some of the members that some of the cooled lavas of a previous age of our planet, when not directly coarsely crystalline and granular, were considered and spoken of as " natural glasses," or perfectly uncrystalline, vitreous, or hyaline masses of matter. Among the first results of the use of the microscope was the dispersion of this fallacy. Sir David Brewster, Mr. H. C. Sorby, and William Nichol (the discoverer of the celebrated calcite prism, which bears his name), had, with greater or less success, examined sections of various rocks and minerals, both by transmitted and reflected light, and also in the form of powder. But, until the genius of Vogelsang undertook the subject, these investigations had no permanent value, nor did they constitute an independent line of mineralogical and geological research. Since the close of his labors, by Vogelsang's premature and much-lamented death, the subject has been made one of renewed interest by his brother-in-law, Ferdinand Zirkel, as well as by Rosenbusch, Tschermak, and many others abroad, and at home by the commencement of a systematic study of the traps of Connecticut by Messrs. E. D. Dana and G. W. Hawes, of New Haven, and by the splendid set of described sections of the traps of the West which have been furnished by Zirkel to illustrate Clarence King's report. I had the honor of presenting a large number of thin sections of our traps at the Washington meeting, for the inspection of the members, with the aid of a table microscope belonging to the Smithsonian Institution. Here I propose to project these sections upon the

By E. G. Leonardon

The object of this paper is to describe briefly the practical results obtained in several problems of civil engineering by resistivity measurements of the underground. It is intended for the mining engineer, as well as for the construction engineer; the stratigraphical problems discussed are general and frequently are encountered in mining exploration. Resistivity measurements have been used in mining and oil exploration for a number of years.' Their introduction in the field of civil engineering, on the contrary, is rather recent. It was applied for the first time in the spring of 1928 near Littleton, N. H., in the survey of two dam sites for the New England Power Assn.2 Since then, the geophysical firm with which the author is connected has had an opportunity to develop this field of activity, and more than 20 investigations at dam and tunnel sites have been carried out in the United States and Canada. A part of this work has been verified by underground or drilling exploration. This paper deals with but a few of the results, which we are permitted to make public now. The theoretical and technical sides of the processes employed will not be discussed; they have already been described in various technical publications. A few general points will be mentioned, to make clear the practical examples given. Resistivities OF the Rocks The surveys are based on the measurement of the specific resistance of the rocks. This resistivity is the electrical resistance of a cylinder of

Jan 1, 1932

By AIME AIME

ON May 5, the Washington, D. C., Section, A.I.M.E., devoted its meeting to the many-sided and perplexing question of mineral stock-piling for peace. Opening the symposium, Harry J. Wolf, of the War Production Board, outlined the problem under six heads: (1) Technical. Mechanical, chemical, or metallurgical importance of specified materials, emergencies that might arise, relative scarcity, and critical value of stock piles during emergencies. (2) Economic. Cost to Government, influence of Government stocks on commercial relationships and markets, effect of availability of items as a con¬structive influence on industry, Administration policies now and during postwar period. (3) Legislative. Need for immediate legislative action, need for legislation on postwar conditions as well as on current requirements, a constructive basic policy to prevent political manipulation. (4) Military. Consideration of re¬quirements and supplies bearing on national safety and needed for manufacture of equipment, and adequate reserves of scarce materials for research or experimentation by military agencies. (5) International. Interests of the United Nations in contradistinction to those of the United States; effects of nonisolation policy on nature, location, and administration of stock piles. (6) Negative stock-piling. Question of United Nations' legislation to prevent stock-piling by Axis nations after the war and who shall purchase stock-pile materials and during what periods.

Jan 1, 1943

By Philip D. Wilson

IT has been my privilege to read the article prepared by R. S. Dean entitled "Production of Alumina from Low-Grade Domestic Materials" which appears on another page of this issue. Dr. Dean should be congratulated on the preparation of such an erudite and scholarly dissertation on bauxite and on the work which the Bureau of Mines has been doing in connection with the development of processes to use low-grade domestic materials.

Jan 1, 1943

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne's statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

By Louis E. Reber

Jan 1, 1922

By Noel S. Christensen

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The commercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depend¬ing upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum' of useful samples.

Jan 1, 1939

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum' of useful samples.

Jan 1, 1939

By G. L. Simard, D. J. Salley, J. Chupak

DITHIOPHOSPHATES and xanthates are the principal collectors for sulphide minerals, and consequently any knowledge of mineral-collector systems of this type is of value. In the present investigation an attempt was made to obtain information on the interaction of a typical dithiophosphate with galena. In carrying out this study, radioiso-topes, so much discussed in the past few years,', ' were extensively employed. By using radioactive dithiophosphate synthesized from radioactive phosphorus, a rapid and sensitive analytical procedure G. L. SIMARD is in the Research Division, Stamford Research Labs., American Cyanamid Co., Stamford, Conn.; J. CHUPAK, formerly in the Research Division, Stamford Research Labs., is now at Camp Detrick, Frederick, Md.; and D. J. SALLEY is in the Research Division, Stamford Research Labs. AlME New York Meeting, Feb. 1950. TP 2815 B. Discussion (2 copies) may be sent to Transactions AlME before April 30, 1950. Manuscript received Oct. 17, 1949. was at hand. This permitted determination of such important quantities as the rate of uptake of dithiophosphate by the mineral, the amount existing at equilibrium on the mineral surface and in the solution, and the desorption of the agent from the surface. Such measurements were possible even on single crystals of galena. In addition the exchange of dithiophosphate between the solution and the sorbed phase was examined, a matter which could be accomplished only by the use of isotopes. It is desired to point out at this time that throughout this paper the term "sorption" has been employed to designate the uptake of agent by mineral, without implication as to the nature of the process by which the uptake was accomplished. Experimental Materials: Galena: The galena was from the Tri-State district. For studies on ground mineral four preparations were used during the course of the investigation. These were prepared from selected large crystals by wet grinding in order to reduce surface oxidation. Alcohol was chosen as a convenient medium for this purpose. The ground mineral was then fractionated by sedimentation in alcohol, dried by evacuation, and stored in a nitrogen-filled desiccator. Data on the preparations are tabulated in table I. The size analysis indicated that the areas of the preparations were of comparable magnitude, even though the absolute values may be somewhat incorrect. Dithiophosphates: Nonradioactive dithiophbsphate (di-isopropyl or di-secondary butyl) was obtained by purification of a commercial product. An aqueous acid solution of the agent was extracted with petroleum ether, the ether layer dried, and the dithiophosphate precipitated as ammonium salt with anhydrous ammonia. Several repetitions of this process resulted in a nearly colorless, flaky product of good purity. (General formula (RO,)PSSNH,). Radioactive dithiophosphate was synthesized by heating radioactive elementary red phosphorus* • For early experiments (1943 to 1944), the elementary red phosphorus was obtained from the cyclotron group at the Crocker Radiation Laboratory of the University of California. Berkeley, through the courtesy of Dr. Joseph W. Hamilton. For more recent work (1946 to 1949). the elementary radioactive Phosphorus has been supplied by the Oak Ridge National Labarotories on allocation from the U. S. Atomic Energy Commission. with sulphur at 270" to 300°C to produce radioactive P,S,. The latter was then treated with the desired purified alcohol (isopropyl or secondary butyl) at 60" to 80°C to form the dithiophosphoric acid derivative. Purification was effected in the same manner as for the nonradioactive material. The effectiveness of the purification method was established by the isotopic dilution method." The same technique was used to show that only negligible decomposition of neutral or of carbonate solutions of the dithiophosphate took place over a period of a day; this was true whether or not galena was suspended in the solutions. Procedures: Radioactivity: The activity of a solution was obtained by counting with a small glass-jacketed, silvered Geiger counter, using a conventional scaling circuit.' Crystals and other solids were counted under a bell-shaped, mica-window counter tube. Sufficient counts were made so that the probable error of counting was of the order of +I-3 pct. The specific activity in terms of counts per minute

Jan 1, 1951

By J. Chupak, D. J. Salley, G. L. Simard

DITHIOPHOSPHATES and xanthates are the principal collectors for sulphide minerals, and consequently any knowledge of mineral-collector systems of this type is of value. In the present investigation an attempt was made to obtain information on the interaction of a typical dithiophosphate with galena. In carrying out this study, radioiso-topes, so much discussed in the past few years,', ' were extensively employed. By using radioactive dithiophosphate synthesized from radioactive phosphorus, a rapid and sensitive analytical procedure G. L. SIMARD is in the Research Division, Stamford Research Labs., American Cyanamid Co., Stamford, Conn.; J. CHUPAK, formerly in the Research Division, Stamford Research Labs., is now at Camp Detrick, Frederick, Md.; and D. J. SALLEY is in the Research Division, Stamford Research Labs. AlME New York Meeting, Feb. 1950. TP 2815 B. Discussion (2 copies) may be sent to Transactions AlME before April 30, 1950. Manuscript received Oct. 17, 1949. was at hand. This permitted determination of such important quantities as the rate of uptake of dithiophosphate by the mineral, the amount existing at equilibrium on the mineral surface and in the solution, and the desorption of the agent from the surface. Such measurements were possible even on single crystals of galena. In addition the exchange of dithiophosphate between the solution and the sorbed phase was examined, a matter which could be accomplished only by the use of isotopes. It is desired to point out at this time that throughout this paper the term "sorption" has been employed to designate the uptake of agent by mineral, without implication as to the nature of the process by which the uptake was accomplished. Experimental Materials: Galena: The galena was from the Tri-State district. For studies on ground mineral four preparations were used during the course of the investigation. These were prepared from selected large crystals by wet grinding in order to reduce surface oxidation. Alcohol was chosen as a convenient medium for this purpose. The ground mineral was then fractionated by sedimentation in alcohol, dried by evacuation, and stored in a nitrogen-filled desiccator. Data on the preparations are tabulated in table I. The size analysis indicated that the areas of the preparations were of comparable magnitude, even though the absolute values may be somewhat incorrect. Dithiophosphates: Nonradioactive dithiophbsphate (di-isopropyl or di-secondary butyl) was obtained by purification of a commercial product. An aqueous acid solution of the agent was extracted with petroleum ether, the ether layer dried, and the dithiophosphate precipitated as ammonium salt with anhydrous ammonia. Several repetitions of this process resulted in a nearly colorless, flaky product of good purity. (General formula (RO,)PSSNH,). Radioactive dithiophosphate was synthesized by heating radioactive elementary red phosphorus* • For early experiments (1943 to 1944), the elementary red phosphorus was obtained from the cyclotron group at the Crocker Radiation Laboratory of the University of California. Berkeley, through the courtesy of Dr. Joseph W. Hamilton. For more recent work (1946 to 1949). the elementary radioactive Phosphorus has been supplied by the Oak Ridge National Labarotories on allocation from the U. S. Atomic Energy Commission. with sulphur at 270" to 300°C to produce radioactive P,S,. The latter was then treated with the desired purified alcohol (isopropyl or secondary butyl) at 60" to 80°C to form the dithiophosphoric acid derivative. Purification was effected in the same manner as for the nonradioactive material. The effectiveness of the purification method was established by the isotopic dilution method." The same technique was used to show that only negligible decomposition of neutral or of carbonate solutions of the dithiophosphate took place over a period of a day; this was true whether or not galena was suspended in the solutions. Procedures: Radioactivity: The activity of a solution was obtained by counting with a small glass-jacketed, silvered Geiger counter, using a conventional scaling circuit.' Crystals and other solids were counted under a bell-shaped, mica-window counter tube. Sufficient counts were made so that the probable error of counting was of the order of +I-3 pct. The specific activity in terms of counts per minute

Jan 1, 1951

By J. H. Richards, G. Derge, W. Peifer

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,' and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By G. Derge, W. Peifer, J. H. Richards

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,' and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By George A. Morrison

THE Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Barberton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITE The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 250 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. GEOLOGY The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft, are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1943

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute. Since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1° to 2°C. per min. with or without slow stirring (Fig. 1). By this method the lead-rich end of the lead-antimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the' liquidus curve of the .binary alloys did not intersect at the eutectic temperature. An equivalent effect was observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent investigation by Pellini and Rhines,1 who determined the eutectic temperature to be 251.5°C. The observation that the curves of primary crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomenon by assuming the existence of a compound Sb4Pb. He felt that super-cooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3. the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature of 250° to 252°C. at a rate of cooling of about 6°C. per min. Abel, Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous, publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic contains only 11,4 to 11.5 per cent antimony. (Previous analyses by Stead4 in 1881 gave 13 per cent:) Weaver," however, reported in 1935 that cooling curves indi-

Jan 1, 1943

By Paul L. Goddard, Alfred G. Hoyl, William R. Sirola

A good place to look for elephants is in elephant country, and old mining districts are certainly elephant country as far as minerals are concerned. In many areas probably more ore is still in the ground than has been taken out. The old timers were good miners and hard workers and when they left ore behind, it was usually for good reason; but many an old mining district has been revived by new approaches to old problems, taking advantage of new techniques and new equipment. One of these is the Front Range mineral belt of Colorado, which has produced minerals for the past 100 years through the ups and downs of mineral prices and the general economy. Gold, silver, copper, lead, and zinc have been found in abundance in the complex sulfide veins of the area. Between Idaho Springs and Central City lie several strong veins which have been mined successfully in the past. The two strongest of these veins, striking northeast-southwest, (Lake-Bald Eagle), and northwest-southeast, (Crown Point-Belman) , and dipping northeast and northwest, respectively, intersect in a flat X near the head of Virginia Canyon. From the lowest drainage of the area, Clear Creek Canyon, the old timers drove the Central, or Big Five, haulage-drainage tunnel due north. It intersects the two veins 8460 ft from the portal and 1670 ft below the surface. The two veins were mined successfully at the surface and at the tunnel level. Without an opening to the surface at the in- side end of the tunnel, ventilating became very difficult as the stopes were opened up, and mining ceased in 1929. Vertically, 1200 to 1600 ft of virgin ground remains in the veins.

Jan 6, 1959