Search Documents

By B. F. Koch

COPPER reverberatories develop large amounts of exit gases of a temperature in the neighborhood of 2000°F. The gases are not only of a noxious nature but must usually be disposed of at considerable heights above the yard level by a stack. Handling these gases at the temperature mentioned would require rather expensive construction of conveying flues and stack. Moreover, wasting such amounts of heat is certainly most uneconomical. Numerous investigations have indicated that waste heat boilers of the water-tube type are the most practical and economical means for utilizing that heat although the gases are heavily laden with rock dust and copper-bearing slag, which upon cooling form hard deposits on the surfaces of dampers or heat absorbing elements placed in the gas stream. Avoiding Slag and Dust Deposits Based largely on the experience of the paper industry in burning black liquor, a waste heat boiler design was developed a few years ago, providing not only extensive water-wall surfaces for cooling the gases below the fusing point of the slag but also settling out, as far as possible, the solidified particles of slag by creating low gas velocity. Matter carried in a stream of gases or air has a tendency to maintain its original direction upon a change in the direction of the flow of the conveying medium. Reverberatory waste heat boilers installed at Hurley and Morenci endeavored to utilize that tendency for the elimination of slagging particles at predetermined places and before they would strike the tube banks of the boilers. Both installations were successful in minimizing the slagging of boiler tubes and thereby minimizing the need for hand lancing. However, the low draft carried at the up-take of the reverberatory furnaces resulted in a positive pressure in the upper part of the furnace of the waste heat boilers, causing the emission of gases from lancing doors and making more difficult the already unwelcome work of cleaning the boilers by handlancing. Attempting to correct this nuisance as much as possible, the overall height of the Chuquicamata waste heat boilers has been reduced to the minimum considered necessary to obtain proper water circulation in furnace walls. Moreover, it is attempted to solidify slag and dust particles by providing large amounts of water-cooled surfaces before the gas stream reaches super-heater and convection banks of the boilers. The furnaces have been made as deep as an economical and practical arrangement of headers for water

Jan 1, 1952

By C. Jardine, D. Freudenreich

The system concept is to minimize costly unscheduled equipment breakdowns by replacing components earlier than their life expectancy. Periodic unit services are scheduled according to preset constraints. Service sheets are generated by matching a job and component master listing based on assigned cyclic component lives. The system can account for all man-hours reported, and history information can be selectively retrieved. By reducing unscheduled equipment shutdowns, this system allows for better manpower utilization and an overall improvement in equipment reliability and availability.

Jan 1, 1982

By E. A. Holbrook

LOCAL yearly taxes levied on bituminous coal lands in Pennsylvania have become a cost of first importance to the coal industry of the State. In Pennsylvania there is no State tax on real estate, but local taxation of real estate furnishes the greater part of the revenue necessary for the small governmental unit, as counties, townships, boroughs, and local school, road, and poor districts. Coal in place in the ground, whether or not title thereto has been severed from ownership of the surface, is assessed as real estate and on its supposed sale or market value. There are eight classes of counties in Pennsylvania, based on population; in populous counties of the first, second and third class, assessments are made by a county board appointed by the county commissioners and are fairly uniform throughout the county. In counties of the fourth to the eighth classes inclusive, property assessments are made by property assessors elected by and for each township within a county. In these counties the board of county commissioners acts as a board of equalization and review to hear appeals. In most counties, therefore, where there is a large unmined reserve of coal, assessments on that coal vary for each township, irrespective of the fact that the coal bed is continuous under many townships.

Jan 1, 1933

By Anton Sawatzky, Erich Vogt

By means of mathematical solutions to the appropriate diffusion equations, we describe the kinetics of the thermal diffusion of hydrogen in Zircaloy-2 for the various temperatures and concentrations encountered in a heavy water moderated reactor. When the hydrogen concentration is below terminal solid solubility only the a Phase is present. Redistributions are then described in terms of the characteristic functions of the difhsion equation. For higher concentrations both the a and 6 phases are present. We assume the two phases to be always in equilibrium. For moderately small hydrogen concentrations exact solutions of the two-phase equation approach the the approximate solutions derived by Sawatzky and for all concentrations the exact solutions exhibit the qualitative features of his result: the two-phase concentration increases with time, everywhere; in the absence of a hydrogen current at the hot end of the sample an a-phase region always exists there; the interface of the a + 6 , a-phase boundary moves toward the cold md of the sample and the hydrogen concentration is discontinuous at the interface. Simultaneous solulions of the a and a + 6 hydrogen distributims and of the concomitant interface motion are obtained and compared to the observations of Sawatzky and Markowitz. The kinetics of the hydrogen diffusion process are shown to lead to m apparent heat of transport of the a phase which is lower than the actual value (even for samples with long anneals) thus resolving at least partially the disparity between experimental measurements of this quantity. A number of recent papers1"4 have reported measurements on the diffusion and redistribution of hydrogen in Zircaloy-2 under temperature and concentration gradients. These studies were instigated by problems arising from increasing use of Zircaloy-2 as a fuel element cladding material in pressurized-water power-reactors. The Zircaloy-2 picks up hydrogen during the operation of the reactor: the consequent precipitation of zirconium hydride in the Zircaloy-2 has pronounced effects on its mechanical properties. The Purpose of the present Paper is to describe the kinetics of the thermal diffusion of hydrogen in Zircaloy-2 for the various hydrogen concentrations and temperatures likely to be encountered in reactors. When the hydrogen in the Zircaloy-2 is entirely in the solid solution phase (a phase), the differential equation for thermal diffusion is well known and the redistribution can be described by standard mathematical methods some of which are given in Section 11 below. The treatment of the a + 6 (hydride) region differs from the earlier treatment of sawatzky3 by taking into account several modifications of the two-phase diffusion equations as suggested to us by Markowitz4 and Kidson.5 Even with the modifications the results obtained in our more complete treatment are substantially the same as those found by Sawatzky. As we show, the difference between the results of sawatzky3 and kIarkowitz4 is largely due to the difference in the geometry of their experiments. In the next section we derive the modified two-phase equation for arbitrary geometry. The exact solution of this equation is given in Section III for linear and cylindrical geometry. It is shown that Sawatzky's approximate solution is quite accurate for almost all the temperatures and hydrogen concentrations which are actually encountered. In Sawatzky's approximate theory the hydrogen concentration everywhere in the two-phase region increases continuously. As his paper pointed out, this result, together with hydrogen conservation, implies that in a sample with no hydrogen current flowing into the hot end a two-phase region is always accompanied by a single-phase region at the hot end of the sample. The net hydrogen gain in the two-phase region is supplied by the decrease of hydrogen in the single-phase region and by the movement of the (a, a + 6) boundary toward the cold end of the sample. Hydrogen conservation at the (a, a + 6) boundary leads to a discontinuity in the concentration and its derivative there. In Section IV it is shown how these qualitative features of the thermal diffusion kinetics arise from the simultaneous solution of the a-phase differential equation and a + 6 phase equation. Methods derived by us previously for the solution of the redistribution in both phases and the accompanying motion of the boundary are used to obtain approximate solutions valid for large times. The solutions account well for the observed redistributions of Sawatzky and Markowitz. It is shown how the continuing motion of the (a, a + 6) boundary leads to measured values of the heat of transport lower than the actual value, even for specimens with relatively long anneals.

Jan 1, 1963

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,' of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,' of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By K. A. Slagle

Hydraulic analysis of the wellbore has become increasingly inzportant for designing cementing operations and selecting equipment, materials and techniques to complenzent modern well-c-ompletion practices. Non-Newtonian fluid technology has advanced beyond the point where former empirical methods of analysis adequately define the hydraulic system and fluid properties. In view of these factors, this paper describes a series of rheological calculations which have been found practical, through field usage, for assistance in selecting a cementing program. A relatively simple laboratory method using standard viscometric equipment is suggested for determination of the rheological properties of slurries, and clrrta are presented on some of the more common cementitrg conzposition.A. A criterion for divergence from laminar-flow characteristics has been proposed. Usefulness of the calculations is indicated by examples of cementing operations where they have been used. INTRODUCTION With the changing aspects of well-completion practices during the past few years, it has been increasingly important to have a relatively simple method of analyzing the flow conditions existing in the well during cementing operations. This is particularly true in view of the improved economics toward which most of the changes have been directed. Rheological characteristics of slurries used for cementing should be a major consideration in the trend toward smaller casing sizes, either single or multiple strings. Receiving increased attention is the practice advocated in 1948 by Howard and Clark' of attaining turbulent flow with the fluids circulated during a primary cementing operation. While there may still be a difference of opinion concerning this technique, most available information indicates that superior primary-cementing results are generally obtained when high displacement rates are employed. Fluid properties of the slurry to be used must be available, as well as calculation methods, to determine what flow rates should be attained and the probable consequences in terms of frictional pressure and horsepower utilization. It would certainly be inappropriate to attempt high displacement velocities if sufficient pressure might be developed to create lost circulation. Since cementing slurries are non-Newtonian fluids, it is not possible to define their rheological or fluid properties by the single factor of viscosity and then make calculations for the quantities just described. Because the shear stress-shear rate ratio is not constant: it becomes necessary to establish at least two parameters for adequate fluid-flow calculations. It is not the purpose of this paper to delve into the mathematical development of non-Newtonian technology, nor to discuss the arbitrary classification system under which a single fluid may resemble two or three different classes depending upon experimental conditions. Rather, the intention is to present a useful series of calculations based on a concept applicable to both Newtonian fluids and to the preponderance of non-Newtonian fluids encountered in the oil-producing industry. Development of this approach was begun some 32 years ago,' and has most recently been brought to fruition by Metzner and his co-workers at the U. of Deleware. Some non-Newtonian fluids encountered in the petroleum industry, other than cementing slurries, have also had the benefit of this method of analysis."' The two parameters required to define the fluid are usually denoted by the symbols n' and K' and, for the purposes of this discussion, are called "flow behavior index" and "consistency index", respectively. These two slurry properties permit calculation of the Reynolds' number and the "critical" velocity, or the velocity at which departure from laminar flow begins. EXPERIMENTAL DETERMINATIONS The two principal instruments used for rheological studies are the pipeline (capillary-tube) viscometer and the rotational viscometer. When conveniently possible, a capillary-tube viscometer (where the pressure drop and flow rate of the material can be measured) is the better method for rigorous determination of the flow behavior index and consistency index for non-Newtonian fluids. With pressure-drop data at various flow rates, it is then possible to prepare a logarithmic plot of shear rate as the abscissa-shear stress as the ordinate. For fluids which do not exhibit time-dependency, these data will usually produce a straight line. The flow behavior index n' represents the slope of this line, while the consistency index K' becomes the intercept of this line at unity shear rate in accordance with the mathematical derivations associated with this concept of rheology. Due to the difficulties anticipated in maintaining a uniform, pumpable cement slurry for the time interval required to obtain measurements from the pipe viscometer, the n' and K' data reported herein were obtained using a direct-indicating rotational viscometer (Fig. 2). The

By A. E. Bellis

THERE is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat-treatment, structure, and physical properties. In order to promote discussion, which it is hoped may lead to the discovery of the source of 'some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat-treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.1 The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08. per cent. The minimum physical requirements are: Tensile strength,- 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirement's gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in- the best heats of open-hearth steel, so that' faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at, a proper temperature clown to the form of tapered barrel blanks or by heat-treating bars that have been upset to enlarge the breech section. The transformation temperature of this steel, on heating, is around 1350° F. (732° C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different

Jan 7, 1919

By John V. Beall

HEAVY-DENSITY separation processes, a commercial application of the sink-float test used in mineralogical laboratories for the separation of mineral particles by their difference in specific gravity, are the biggest development in mineral dressing since flotation, which was at about the same stage of development thirty years ago. The scope of their application has broadened and, though still in the development stage, they are being accepted in a constantly increasing number of commercial installations. This progress in mineral beneficiation is especially satisfying when we realize that our high-grade ore deposits are fast disappearing and a big factor in determining whether a hole in the ground is being sat upon by a liar or an honest citizen is how economically the ore dressers can concentrate comparatively low-grade ores. As early as the middle of the nineteenth century attempts were made to use aqueous salt solutions in a heavy-liquid separation for cleaning coal. But the original and recovery costs of these liquids were high and further, the fact that they were corrosive, unstable, and toxic added to the difficulty in using them.

Jan 1, 1948

By E. Just

The mining industry is guaranteed an important future because its products are indispensable. However, this can be anything from a brilliant, efficient, profitable future to one of being a heavy-handed, dull-witted claimant for public handouts, according to the caliber and training of the young men who enter the industry. Many views have been expressed about the type of education needed for today's mining industry. Criticisms have been aired to the point that further controversy amongst ourselves could be detrimental to both mining education and the mining industry. It is time we get together and start going somewhere. To canvass the various attitudes of mining educators, a questionnaire was sent to a group of these dedicated, intelligent men, whose primary interest is to help the industry and the profession. The following is a summary of their views.

Jan 9, 1961

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By W. B. Stephenson

In the pumping of sands, slurries and slimes, practices developed over the years are the real keystones of 'successful operation. These practices are necessarily based on modifications of familiar theories. Practical methods used in the solution of problems involving the pumping of materials are set forth in the following discussion. Basic Requirements To pump sands and slurries economically, a few basic requirements must be met by the pumping system as a whole. A pipe-line velocity must be established that will move the fluid mixture throughout the entire system without any possibility of the solids settling out. To accomplish this, the velocity of flow must be slightly in excess of the critical velocity of the mixture. The critical velocity of a mixture varies from 3 ft. per sec. to 18 ft. per sec., depending on the screen analysis, concentration, and specific gravity of the solids in the mixture. Most tailings are pumped at a minimum velocity of 4 ft. per sec. if they include slimes, whereas the pipe lines of sand and gravel dredges require velocities as high as 18 ft. per second. A number of articles have been written on the determination of the minimum velocities required to maintain solids in suspension. Studies have also been made on the friction and pumping heads developed when handling solids in suspension.1-4 Our experience so far has shown that, within the normal operating limits of a pumping system, the friction factor follows more nearly the basis described by Howard,' who says, among his conclusions: "... values of f (friction factor) . . . will decrease with an increase in velocity." This conclusion is borne out by our actual experience. When the velocity in a pipe line is not sufficient to keep the solids in suspension, the total friction head' is greater than when the velocity is increased to a point where the solids are in suspension. A slight increase in the volume of feed to the pump and a slight increase in the pump speed are usually all that is necessary to put the system in balance. Maintaining Constant Volume Within reasonable limits, the volume of mixture to be handled through a pipe line should be held constant, so that the required velocity will be provided at all times. There are several ways in which this can be accomplished. The commonest is to provide a sump of sufficient capacity to take care of slight surges in the volume of mixture being fed to the pumping systen]. This sump, however, should not be as large as a settling chamber. The use of a float-controlled, fresh-water make-up valve in a sump will guarantee a constant volume. Where variations in volume are slight,

Jan 1, 1947

By W. B. Stephenson

In the pumping of sands, slurries and slimes, practices developed over the years are the real keystones of 'successful operation. These practices are necessarily based on modifications of familiar theories. Practical methods used in the solution of problems involving the pumping of materials are set forth in the following discussion. Basic Requirements To pump sands and slurries economically, a few basic requirements must be met by the pumping system as a whole. A pipe-line velocity must be established that will move the fluid mixture throughout the entire system without any possibility of the solids settling out. To accomplish this, the velocity of flow must be slightly in excess of the critical velocity of the mixture. The critical velocity of a mixture varies from 3 ft. per sec. to 18 ft. per sec., depending on the screen analysis, concentration, and specific gravity of the solids in the mixture. Most tailings are pumped at a minimum velocity of 4 ft. per sec. if they include slimes, whereas the pipe lines of sand and gravel dredges require velocities as high as 18 ft. per second. A number of articles have been written on the determination of the minimum velocities required to maintain solids in suspension. Studies have also been made on the friction and pumping heads developed when handling solids in suspension.1-4 Our experience so far has shown that, within the normal operating limits of a pumping system, the friction factor follows more nearly the basis described by Howard,' who says, among his conclusions: "... values of f (friction factor) . . . will decrease with an increase in velocity." This conclusion is borne out by our actual experience. When the velocity in a pipe line is not sufficient to keep the solids in suspension, the total friction head' is greater than when the velocity is increased to a point where the solids are in suspension. A slight increase in the volume of feed to the pump and a slight increase in the pump speed are usually all that is necessary to put the system in balance. Maintaining Constant Volume Within reasonable limits, the volume of mixture to be handled through a pipe line should be held constant, so that the required velocity will be provided at all times. There are several ways in which this can be accomplished. The commonest is to provide a sump of sufficient capacity to take care of slight surges in the volume of mixture being fed to the pumping systen]. This sump, however, should not be as large as a settling chamber. The use of a float-controlled, fresh-water make-up valve in a sump will guarantee a constant volume. Where variations in volume are slight,

Jan 1, 1947

By NEWTON B. KNOX

THE Guianas region is a geological unit, consisting of the northern lobe of the Brazilian Shield, but political accident and the fact that rivers act as the principal means of transportation have divided the region between five separate sovereignties. Brazilian and Venezuelan Guiana have already been considered. The French, Dutch, and British colonies consist of a coastal plain some fifty miles wide, which, together with the lower reaches of the principal rivers, support the greater part of the population. Inland from this tidewater region is a wide area of low, forest-covered hills, under-lain by gneisses, schists, granites, and pegmatites of the Shield. As in Venezuelan Guiana, these rocks are overlain by a thick series of horizontal continental sediments intruded by moderately basic magmas. Gold, bauxite and diamonds have been the principal products of the colonies. The first metal is quite widespread in the hill country. The quartz mines are small, though occasionally rich; probably the greater number of veins remain undiscovered because of the thick mantle of decomposition product that covers the schists and gneisses. The greater proportion of the gold, therefore, is derived from placers which are exploited in all three colonies. Some geologists claim that they occur in two belts parallel to the coast; whether this feature has its origin in the location of the primary mineralization or in the gradients of the rivers is not clear. In some instances the river gravels grade into auriferous laterite. The laterites are well developed in the Guianas and represent the weathering products of the more basic rocks.

Jan 1, 1946

By Haley, D. F.

WHEN operations were first started at Climax in 1917 by the Climax Molybdenum Co., they were pioneering in the molybdenum industry for little was known relative to the uses of molybdenum or the metallurgy of molybdenite concentration. Concentration of molybdenite is relatively simple today but in 1916, when the Climax deposit first attracted attention, it presented serious difficulties. Little was known, in fact, even about the assaying of such low-grade molybdenum ores. Mine samples were sent to at least a dozen of the best laboratories in the United States and average values reported varied from 0.4 per cent to 1.0 per cent MOS2. Owing to the wide variations in MoS2 content obtained from reliable chemists, the actual value of the ore was most uncertain. This variation occurred repeat¬edly over a period of six months in 1917. It was finally decided, as a last resort, to cut several tons of sample from the tunnel and have a mill test made, using the recovered MoS2 per ton as the grade of the ore, for a small error in the assaying of the concentrate would not materially affect the results. These mill tests were made by the General Engineering Co. (Callow) at Salt Lake City. The results proved an ore of commercial grade and indicated the flotation process for the best metallurgy. Based upon these tests, the decision was made to build a 200-ton flotation plant. At this time, the art of flotation was

Jan 1, 1946

By M. F. Goudge, R. V. Tomkins

Sodium sulfate is an important chemical raw material that is being used in ever increasing quantities in modem industry. It comes on the market mainly in three forms: (1) Salt cake (Na2SO4), a relatively crude form of the anhydrous salt containing up to 3 pct impurities, and comprising about three-quarters of the North American production; (2) anhydrous sodium sulfate (Na2SO4), a refined form containing less than 0.3 pct impurities; (3) Glauber's salt, the decahydrate (Na2SO4.10H2O) containing 55.9 pct water of crystallization. Competing with salt cake from natural sources is byproduct salt cake from a number of industrial operations. For instance there is Mannheim cake resulting from the manufacture of hydrochloric acid by the reaction of salt (NaCl) and sulfuric acid in Mannheim furnaces; rayon cake, a high-quality product, resulting from the process of making rayon by the viscose process; chrome cake from the processing of sodium chromate to dichromate; phenol cake from the manufacture of phenol; also byproduct sodium sulfate resulting from the conversion of lithium sulfate to lithium carbonate; from the processing of sodium tetraborate to boric acid; from converting sodium formate to formic acid; and in the manufacture of cellophane. Sodium sulfate is also obtained as a byproduct in the manufacture of isosebasic acid. In addition strong competition has resulted from imports of byproduct salt cake from the chemical industries of a number of highly industrialized European countries. However in recent years due to technological changes the output of byproduct salt cake is rapidly diminishing and the natural deposits are becoming the most important source of sodium sulfate used in North America. For instance, the production of hydrochloric acid in Mannheim plants has become obsolete and thus the greatest single source of byproduct salt cake will disappear. Also viscose rayon is meeting strong competition from nylon and other synthetic fibers and production of byproduct salt cake from this source may do little more than remain at the present level. These factors together with increasing demand for sodium sulfate point to increased production from natural sources. In 1958, 36 pct of the total United States production was derived from natural sources and in addition 97,000 short tons was imported so that over 40 pct of the total consumption was supplied by natural sources whereas in 1953 the proportion was only 24 pct. The rapid growth in production is shown in Table 1. Principal Sodium Sulfate Minerals There are many minerals in which sodium sulfate is a constituent but those of commercial importance at the present time, and consisting wholly of sodium sulfate in either the hydrous or anhydrous states, are mirabilite and thenardite. Minerals of potential importance but consisting in part of compounds other than sodium sulfate are glauberite in which sodium sulfate is combined with calcium sulfate, and blödite in which sodium sulfate is combined with magnesium sulfate. Mirabilite (Na2SO4.10H2O) the decahydrate, consists of 24.8 pct SO3, 19.3 pct Na2O, and 55.9 pct H20. It is a colorless to opaque, soft, water-soluble mineral with a slightly bitter taste. It has a hardness of less than 2 and a specific gravity of 1.48. It forms long needle-

Jan 1, 1960

By Herbert W. Huse

Nitrogen, and its compounds, unique among the materials described in this volume, is absolutely essential to the existence of the human race. Almost all minerals are important and the absence of any one of them would be sorely felt; but nitrogen is an integral part of the cycle of life itself. Man cannot live without nitrogen which, as an inert gas, composes the major part of the air he breathes; as compounds, nourishes the vegetation which he eats; and, as protein, forms a part of his very flesh and blood. Nature originally provided man with a vast reserve of usable nitrogen compounds in the form of fertile soil. She constantly replenishes the supply by "fixing" nitrogen in the air at the estimated rate of 400,000,000 tons per year (an insignificant 6 lb per acre) during electrical storms. She has also placed certain microorganisms in the soil which are able to "fix" nitrogen and convert it into forms which plants can use. Legumes like cow peas, soy beans, clover, and alfalfa have extraordinary roots which serve as stimulating hosts to these bacteria which, in turn, nourish the plant. By plowing in all or part of such crops, their above-average nitrogen content can be returned to the soil for other more useful crops. The mechanism for this recycle is supplied by "denitrifying" bacteria which attack the dead plant tissue and liberate nitrogen and ammonia. However, since one crop of grain, sugar beets, potatoes, tomatoes, etc., takes out a major portion of the nitrogen which a plowed-in legume crop can supply, this method of fertilization is obviously inadequate. Drastic intervention by man has become necessary to support the ever-growing population of the world.9,15,20 Old civilizations with a high population density, such as the Chinese, were able to exist for centuries by carefully tilling the soil, rotating crops, and returning to the soil all the nitrogen in vegetable wastes plus human and animal excreta. But the lack of a means for augmenting their supply of nitrogen placed a ceiling on further development and kept the mass of the population in a chronic state of undernourishment, frequently punctuated by famine. Nitrogen plays another important role in the life of mankind. In the form of explosives, nitrogen helps to wrest from the earth many materials needed for our material well-being. Also, in the form of explosives and propellants, nitrogen increased the destructiveness of wars to a point only exceeded by the fantastic power of atomic energy. Man's first really effective efforts to improve his position with respect to nitrogen began in the 18th Century with the mining of sodium nitrate. By the late 1880's this had become a big industry serving a large part of the world. In the late 1890's nitrogen, in the form of ammonia, was being recovered from coke-oven operations. In 1900 nitrogen, in the form of nitric oxide, was being obtained from the air by an electric-arc process. About 1904 another "fixation" process based on the reaction of nitrogen with calcium carbide to form cyanamide was commercialized. By 1913 the Haber-Bosch process of "fixing" atmospheric nitrogen by reacting it with hydrogen to produce synthetic ammonia was successfully applied on a large scale, first in Germany and then throughout the industrial areas of the world.9 All the above methods of obtaining nitrogen compounds are still in use and, between them, they assure mankind of adequate supplies for all time. While this fortunate situation is not unique amongst industrial raw materials, all too few of man's needs are so well in hand.

Jan 1, 1960

Discussion of the paper of L. C. Graton and Joseph Murdoch, presented at the New York Meeting, February, 1913, and printed in Bulletin No. 77, May, 1913, pp. 741 to 797. THOMAS T. READ, New York, N. Y. (communication to the Secretary *) :-At the meetings of English technical societies it not infrequently happens that, during the discussion of a paper, someone will arise to say that although he highly appreciated the material presented, nevertheless he believed it would have been better if some other phase of the question had been more highly emphasized. Assuming that this form of discussion is permissible in the Institute, I should like to reiterate the point made by Prof. A. J. Moses that conclusive proof of the identity of the minerals in question is an essential feature of the study of ores in this way. This is also expressed by Paul Krusch in his recent valuable paper 1 on the sulphide ores (in which he arrives at conclusions diametrically opposed to those of Mr. Graton), as follows : ?The diagnostic properties of the various ore minerals are known to but a limited circle of investigators." Many earlier investigators began the study of ores beneath the microscope by reflected light, but discontinued their work, in most cases, because they were unwilling to undertake the great amount of preliminary work necessary to securely establish a basis for their inferences. It is evident that Messrs. Graton and Murdoch realize that the promised later paper on diagnostic characters will be the more important of the two, but the point should be emphasized to forestall a flood of literature from other investigators who may gain the impression that the brief survey of polished specimens is a wade mecum to incontrovertible conclusions as to any given ore deposit.

Jan 10, 1913

By R. M. Brick

SEGREGATION can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming. steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-12 per cent Si alloys. The phasial condition implicitly described above-solidification over a range of temperatures with a compositional difference between solid. and liquid-is found in nearly all solid solutions or combinations of solid solutions and eutectics. Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually determinable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be. described first because it is an essential part of the picture. CORING Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus 1, 3, 7 and solidus 2, 5, 8, and where the vertical 1, 4, 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. 1b) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1944