Search Documents

By T. Reed Woodbridge

The object of this paper is to bring to notice a method in use at the Cedar Point laboratory of Witherbees, Sherman & Co., for determining the phosphorus in the ore mined at Mineville, N. Y. This ore is magnetite, with a gangue containing crystals of apatite. In 1886, Mr. H. F. Dawes, then head chemist at the works, suggested that as all the phosphorus seemed to be in the apatite, it could be obtained in solution by dilute nitric acid. After some experimenting the following method was adopted, and has proved invaluable for rapidity and ease; half a dozen determinations requiring very little more time or trouble than one. From + to 10 grammes of ore are weighed into a 150 c.c. beaker; 50 C.C. hot water and 10 c.c. strong nitric acid are added; the beaker is covered and the contents are boiled for 1/2 hour (10 minutes sometimes proves sufficient; but 4 hour is safer). The bumping which ensues if more than & gramme is used need cause no trouble. The hot solution is filtered into a 250 C.C. beaker. The filtration and washing (with hot water) proceed rapidly, as the magnetite itself is but slightly acted upon. After the addition of 15 C.C. ammonia and 15 c.c. nitric acid, the solution is cooled to 45' C., and from 15 to 40 C.C. of molybdic acid solution is added and stirred vigorously. In 5 minutes the precipitate will be down, and the determination can be finished by any good method. At Cedar Point the method more commonly used is weighing as yellow salt. Good washed filter-paper is used, No. 0 Swedish being preferred; and dozen 3 1/2-inch filters are numbered and dried and weighed at 110°C. These are always kept in stock. The yellow salt is filtered on one of these, washed with dilute nitric acid (2 per cent. by volume); dried for 1 hour at 110' C., and then weighed, 1.63 per cent. of weight being calculated as phosphorus. The filters vary in the two weighings from

Jan 1, 1889

By R. L. Wiegel

The generation of operating information for mineral beneficiation processes has become more sophisticated as a result of the use of improved laboratory analytical techniques, some of which provide multiple component assays, as well as the introduction and gradual industrial acceptance of process sensors for the measurement of flow, density, size, and chemical composition. In general, however, the mineral processing engineer's ability to tie together this wealth of information has not kept pace with these developments. In fact, in almost all existing plants, the metallurgical inflow-output balance, wed to indicate current process performance, is still being calculated from only a small portion of the information routinely available. There is substantial activity in the development of techniques for using all available process information to significantly improve the reliability of the metallurgical balance. While the use of these improved techniques does require access to computing facilities and a slight change in perspective on the part of the mineral processing engineer regarding the inviolability of process information, there are numerous practical benefits to be derived from their application. In addition to summarizing some of the concepts basic to these techniques, this paper describes the experience of the author in applying one of these advanced metallurgical balance techniques to a variety of pilot plant and commercial plant flowsheets during the past eight years.

Jan 1, 1983

By L. D. Rickets

The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be entrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reenforcing detail that clothes and tends to disguise them. This especially applies to those who would dream dreams that may come partly true. Professor Henry B. Cornwall of Princeton was a graduate of Freiberg with mining experience in Mexico. He was my friend and mentor during my college life. In 1883 I finished my postgraduate course and had two offers of work to consider. His advice is very clear in my mind today. It was essentially as follows: I know something of the mines of Mexico and have crossed through the mountains of the West. The West possesses a vast area of mountain and valley. California has long had its gold mines, the Comstock and Gilpin County followed and now comes the discovery of Leadville. I believe the West, will become a great mining country. You can choose now to teach here or go to the mountains. Were I in your place I would go West and identify myself with mining.

Jan 1, 1932

By Walter L. Crow

MUCH has been published on highly technical phases of grinding. Very little has been written on how a mill man can improve his operations by determining the optimum size assortment of grinding balls that should be added as a makeup charge. This ball rationing is not to be confused with the ball ration used as an initial charge when the mill is started up. Ball rationing is considered for one or more of the following purposes: 1) to increase throughput of the mill, 2) to reduce the power required per ton of ore ground to the desired size, 3) to reduce steel consumption per ton of ore ground, 4) to improve product size, and 5) to lower retention time of ore in the mill.

Jan 7, 1957

By J. V. W. REYNDERS

NOT only is your toastmaster silver-tongued in his references 'to myself, but he is also quite in the habit of "saying it in silver." I have analyzed with some care his statistics of the world's silver production, which have been distributed here along with the menu, although frankly from the point of view of most of us, the distribution rather than the production of silver is of immediate concern. Unlike the performers by whom we have been entertained between courses, the rest of us on the program will have to do without costume or musical accompaniment, which as my friend Rains can testify puts an artist under severe strain. I am entitled by right of office and of precedent to receive your attention for ten minutes. The Governor, who appears on the program as a speaker; however, has asked me for five minutes of my time, and Senator Thomas has insinuated that he would appreciate one-half of the remainder, wherefore, I must ask your close attention to the very brief remarks that I am able to make under such restricted circumstances. To begin with, I want you to believe that I am approaching the task set by your toastmaster with misgivings. In looking over the Institute records relating to the Salt Lake City meeting of 1914 for some precedent as to what I ought to say, I found but one reference-and that of the following indefinite char¬acter-" and Friday night there was a hilarious banquet to 350 members and guests."

Jan 1, 1925

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By S. G., Lasky

IT seems to be in the nature of concepts that they have many meanings, and that the meaning best reflecting the primary interests of a person tends to be accepted by him as the normal meaning of the concept. The concept of ore reserves is no exception, for there is no unanimity of meaning among the several groups of us who are interested in ore reserves, nor even among the individuals of a single group. The groups most interested in ore reserves would seem to include at least the mining industry, perhaps State taxing agencies, and the Federal Government in all its diversified activities, and I would include also the citizenry at large or at least that part of it that consciously thinks about problems-of national welfare. To each of these, and to different individuals within them, the term reserves represents something different, and the farther away the individual or group gets from physical contact with the ore, the more abstract does his or its concept become. It is something different to the policy maker from what it is to the fact-finder or to the miner.

Jan 1, 1945

By H. B. Treweek, V. R. Degner

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976

By T. A. Wright

THE-Institute of Metals Division opened on Tuesday afternoon with Wheeler P. Davey as chairman and G. E. Edmunds as vice-chairman. Four papers were on the program, two being of a fundamental character. A paper on "Internal Surface in Minerals and Metals," by R. S. Dean and J. Roster, was presented by the latter; C. H. Gottschalk discussed coercive forces in powders. In answer to a question by the chairman. The author stated that he had not investigated [he temperature coefficient of resistance. A paper on "Recrystallization and Grain Growth in Cold Worked Polycrystalline Metals," by L. W. Eastwood, Arthur E. Bousu, 'and C. T. Eddy, was presented by Mr. Eastwood. A. great many quantitative data were given, with little reference to the theory. Theoretical considerations were discussed by Dr. Gottschalk, and C. A. Edwards of the University College of Wales, contributed very interesting comment on the relationship of size and critical strain. Dr. Edwards discussed the necessity of considering strain with time and temperature.

Jan 1, 1935

By J. W. Spretnak, R. Speiser

IT has been suggested that boron in steel may form a film entirely around the austenite grain and that this film is responsible for the boron hardenability effect. In this connection, it is of interest to examine some of the ramifications of the concentration range of boron usually employed in hardenable steels, namely 0.0005 to 0.003 pct in a grain size range of ASTM grain size No. 1 through No. 10. The ratio of the iron to boron atoms and the number of unit cells of y iron per boron atom are listed in Table I. Even at the highest concentration considered, there are 1600 unit cells of y iron per boron atom, assuming a uniform distribution of boron. To investigate the possibility of the boron film formation, the number of boron atoms required to cover the grain surface completely must be calculated. With some transition elements, boron crystallizes in sheets composed of equilateral hexagons very much like graphite.' The selected value for the length of a side is 1.80Å. A simple calculation shows that two boron atoms cover an area of 8.4x l0 -16 sq cm. Table II lists the number of atoms of boron required for the formation of the monatomic film and Table III lists the number of boron atoms per grain. The hypothetical cases of 100 pct and 10 pct adsorption are calculated (all boron atoms in a grain and 10 pct of all boron atoms in a grain are located at the grain surface respectively). In Table 111, all combinations of grain size and composition below and to the left of the solid line (100 pct adsorption) and the dashed line (10 pct adsorption) are excluded as to the possibility of covering the grain surface with a continuous boron film. Thus, even for 100 pct adsorption, the smaller grains can form the film only at the higher concentrations. For the best case, grain size No. 1 and 0.0030 pct B, the required degree of adsorption is 3.9 pct. The above calculations deal only with the number of boron atoms required to form a monatomic film and do not take into account the mechanism of concentration of boron at the grain surface and the possible limitations to the extent of this concentration at a constant temperature, as for example in the austenitizing process. The question next arises as to how this surface concentration can occur during an isothermal treatment. Such surface enrichment of boron must occur through the phenomenon of surface adsorption, i.e., the concentration of solute atoms in solid solution in the vicinity of the surface without precipitation. A solute atom will tend to concentrate at the grain boundary if it reduces the interfacial tension. The possibility of adsorption effects involving both boron and carbon in iron has been discussed.' In general, the tendency for a sol-

Jan 1, 1954

HARD as it is at any time to provide more than three million tons of coal each year for power plants, the task really gets rugged in the wintertime when the fuel freezes solid in the cars. At the Marysville plant of the Detroit Edison Co. the problem of unloading cars of frozen coal was severe because there was an unloader over only one of the two tracks in the coal unloading house. Moving downward by their own weight, with no driving force to aid them, the spuds of this old unloader were unable to break through the crust on a frozen coal car. 20,000 Lb Force To meet this problem, a new mechanical car unloader was installed over No. 2 track and placed in service in December 1947. It is a Kenney type unloader built by Heyl & Patterson, Inc. of Pittsburgh, Pa., a modification of equipment originally designed to unload iron ore cars. The major advantage of this unloader is the force with which it can drive the sharp spade on the end of its ram down through the pockets of a frozen coal car. The unloader consists of the following major units: 1. A traveling bridge structure. 2. A traveling trolley. 3. A retractable and oscillating ram. 4. The operators cab and controls. The bridge is provided with safety hooks to prevent its being lifted from the rails by the upwards push of the ram. The bridge will travel 190 fpm and has sufficient traction on its four wheels to move three loaded 70 ton cars. The trolley runs on tracks supported by the bridge girders and also has upper tracks to control the push from the ram. Two of the single-flange trolley wheels are driven by a one and a quarter hp dc motors equipped with magnetic brakes. The ram is raised and lowered by a 20 hp dc motor equipped with a magnetic brake. A full stroke of a little over 14 ft is given the ram through its rack and pinion drive and the spade can be pushed down into a loaded car with a force of about 20,000 lb. A 15 hp dc motor with a magnetic brake is applied to this drive and is able to swing the ram 45º either side of the vertical. The usual procedure in emptying a coal car is first to drive the sharp spade down through the coal until the pocket is opened and the coal starts to run out the hopper. When all the hoppers are open, the sweeping action of the ram and spade is used to move the remainder of the coal in the car over to the open hoppers. The travel of the trolley permits cleaning the sides of a coal car with the edges of the spade, using the sweeping motion of the ram. It is still necessary to clean out the corners of the car by hand. Final Clean-Out This unloader was a new development and there were improvements to be made before it was completely satisfactory, such as reduction in speed and conversion to ac drive motors. However, it helped at Marysville and unloaded many frozen cars that would have taken a lot of heating to thaw out enough for the old unloader to handle. The mechanical coal unloader described above was a considerable improvement but still left a job to be done by hand-the final cleaning out of the coal cars. The ram had the ability to open a hole through the hopper cars, but did not meet required unloading speed. To eliminate hand cleaning a car shakeout, manufactured by Hewitt Robins, Inc. was added to the installation. This equipment is used to clean the coal car out after the unloader has provided an

Jan 1, 1952

By L. B. Slichter

After statement of the principles of similitude which apply to electromagnetic modeling, charts showing the inductive response of conducting spheres as dependent upon frequency, conductivity, and size are exhibited in this paper. The shape of the curve which relates intensity of response to frequency is significant in indicating the advisability of low frequencies in the exploration for conducting bodies, when consistent with the securing of a large percentage of the ideally possible response. Comparisons of theoretical response and that observed with models are shown, and relationships with the subject of applied electromagnetic prospecting are indicated. Maxwell Field Equations The Maxwell field equations summarize the physical laws that govern electrical field phenomena; they are the basis for the solution of electromagnetic problems. These concise equations, with adequately formulated boundary conditions, specify the complete electrical condition of continuous media, and the development of their solution amounts merely to a more convenient re-expression of phenomena already completely described. Thus, the immediate content of the field equations themselves is sufficient and sometimes convenient for the treating of certain questions (such as those relating to electromagnetic models) which are independent of the special factors of geometry, or the nature of an impressed field. The four Maxwell field equations are written below, in c.g.s. gaussian units: curl E = -B/c [21 div eE = 4pp [31 div B = 0 [41

Jan 1, 1932

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Herewith are submitted the report of the Treasurer for the year 1936 and the reports for the same year of the following committees: Admis¬sions, Membership, Papers and Publications, Library, Student Relations, and MINING AND METALLURGY. To these reports you are referred for details of the year's activities. Finances.-Income for the year was $173,091 including an appropria¬tion of $2500 from the Rocky Mountain Fund earmarked to defray expense for official visits to western Sections and student societies. This compares with $141,754 in 1935 and exceeds by more than $50,000 the income of 1933 wherein the low point during the depression was reached. The major items of increase were: $6,700 from current dues; $10,600 in initiation fees and dues of newly enrolled members; $10,800 from the monthly magazine MINING AND METALLURGY. Sundry small declines were offset by minor increases. Expenditures for the year totaled $176,007 compared with $148,361 in 1935. Major increases were $5,700 for MINING AND METALLURGY; $4,000 for TRANSACTIONS and TECHNICAL PUBLICATIONS; $1,500 for meetings; $1,300 for Local Section appropriations; $6,500 for Technical Division expense; $5,000 for Increase of Membership expense; and $2,500 for visits to Local Sections and educational institutions. Comment on several of these items will appear under subsequent heads. Net deficit for the year was $2,915, this sum being made up from the accumulated surplus. It is interesting to observe that the net excess of income over outgo for the five-year period 1932-1936, inclusive, is $760. Membership and Dues.-During the year there was a net gain in membership, including Members, Associates, Junior Members and Junior Foreign Affiliates of 755 (from 7116 to 7871). In addition there was a gain of 616 in Student Associates (from 1004 to 1620). Taking account of small losses totaling 5 in the other grades, the net increase was 1366 bringing the total to 9607, the highest figure reached in the history of the Institute except at the end of 1921 when the total was 9850. In part the gain is accounted for by the smaller number lost by suspension

Jan 1, 1937

By R. B. G. Yeo

The effects of alloy additions on the M, and A, temperatures of an Fe-22.5 pct Ni alloy have been determined. Increasing amounts of titanium, colum-bium, vanadium, and silicon raise and then lower M,while raising A, cmtinuously. Cobalt raises both M, and A,. Aluminum has little effect on Ms but raises A,. Chromium md nickel lower M, and A,. It is proposed that elements raise M, in accordance with their effect on the Ae3 temperature of iron until the lattice becomes stiffened against the shear transformation so that M, is then lowered. An anomaly, first pointed out by Zener,1 arises in steels when the addition of elements, such as molybdenum and tungsten, which raise the Ae3 temperature, also lower the M, temperature.2'3 During the development of a series of martensitic precipitation-hardening (maraging) steels, the effect of several elements on the transformation of austenite to martensite was studied. The results show that under suitable conditions several elements which raise Ae3 also raise the M, and A, temperatures. PREPARATION OF MATERIALS STUDIED A series of alloys was made in which cobalt, titanium, columbium, vanadium, silicon, aluminum, molybdenum, chromium, and nickel were added to an iron base containing 22.5 pct Ni. The compositions of the alloys prepared are given in Table I. The residual manganese contents of the heats were in the range of 0.030 to 0.35 pct, silicon 0.05 to 0.1 pct, carbon 0.0008 to 0.009 pct, and nitrogen from 0 to 0.004 uct. The allois were made as 50-lb induction heats starting with electro-iron and electro-nickel, melted in air to oxidize impurities. Additions of silico-manganese and ferro-silicon were made after which the power was turned off to allow the products of deoxidation to rise and be skimmed from the surface of the melt. The furnace chamber was pumped down to a pressure of 5 p and the charge was heated to 2900°F for the addition of other alloying elements. The heats were poured into five 10-lb ingots, making successive alloy additions to each. The ingots were soaked for 2 hr at 2300°F and hot-worked to 3/4-in.-diam bars. This stock was heated to 1500°F for 1

Jan 1, 1963

By N. Cabrera

IN a recent paper Kuczynski' studied the rate at which the crack between a metallic plane and a spherical particle of the same material is filled up gradually when heated at temperatures near the melting point. If x is the radius of contact between plane and sphere (fig. I), Kuczynski shows experimentally that x5 = At [1] where t is the time. Assuming that the mechanism of transport of matter is the volume diffusion of vacant lattice sites, he is also able to prove Eq 1 theoretically. The constant A contains as a factor the self-diffusion coefficient of the metal and he shows that the values for this coefficient deduced from his experiments yield the same activation energy as that calculated by other methods, which is a confirmation of this point of view. Kuczynski has also considered theoretically the law of growth of x which would be expected if surface diffusion were the important mechanism. He suggests that x should then obey a law of the form x7 = At, and claims to be able to decide the mechanism involved from the observed law of growth., The purpose of this note is to prove this incorrect. On the contrary, when the mechanism is surface diffusion Eq 1 is also obeyed, but with a different constant A. Following Kuczynski, we suppose the bottom of the crack (surface A A) to have an average radius of curvature p. As a result of this curvature the concentration of adsorbed atoms in this surface, n(p) per cm2, will be smaller, and the concentration of vacant lattice sites in the neighborhood, N(p) per cm3, will be larger than the corresponding concentrations, n(w) and N(w), for a flat surface. For all practical cases we can write Thomson's formula in the form n(co)— n(P) N(P)—N(cc) _ 2a-a" n(oo) JV(co) kTp [2] where u is the surface energy of the metal and a the interatomic distance. 1. Let us now consider the mechanism of surface diffusion. We suppose the concentration of ad-

Jan 1, 1951

By Anthony Tuke

Members of the Society of Mining Engineers may well regard it as rather unusual that a paper on this subject is being presented by someone whose first taste of mining came at the age of 60 or so - someone who last heard of cathodes and anodes in 1938. On the other hand, the title does refer to the financing of a mine and at least I can claim to have spent all my business life since the war until 1981 in the world of banking, though this inevitably means that I have been used to looking at these and other problems through what you might regard as the wrong end of the telescope. The lending of money, and more particularly the provision of finance for commerce and industry, is the central job of a banker and I have been involved in this in various ways over many years, but regrettably only very marginally in the world of mining. As you will see from what follows, the rather specialised form of finance which RTZ required was, to my regret, not provided by the British banking community since the great majority of the finance came from American banks and, to a lesser extent, from German banks. I am most indebted to Mr. Roy Wright for a great deal of the nuts and bolts in this paper. He was one of the three central figures in the growth and expansion of RTZ during the 1950's and 1960's and was right at the centre of the negotiations with bankers, with governments and with many others. The going, as you will see, was far from easy. The essential basis for the financing of each of the RTZ group's mining projects was a firm long-term sales contract for sufficient of the output of the particular mine to produce the cash flow necessary to service the loans. Wherever possible, loans were raised in the same currency as the sales contracts were made. Each sales contract was designed to give the customer the product he wanted with a long-term assurance of supply and at the same time to give the bankers the protection they required. Thus the marketing concept and the financing concept for a particular mine formed one overall plan, and talks with the customers and the bankers were conducted in parallel until a satisfactory marketing/financial package was agreed in principle. Preliminary talks were begun soon after the discovery of a potentially viable orebody. As confidence about a discovery increased, customers were persuaded to enter into contingent sales contracts before the very detailed and costly business of the economic and technical feasibility study of the mine was launched; such a study might cost 10% or more of the estimated total capital cost. At the same time provisional understandings were reached with the bankers. The contingent sales contracts usually gave a period of grace of eighteen months to two years, during which time the decision whether or not to continue with the mine had to be made. This decision rested mainly on the result of the feasibility study and also on coming to a firm agreement with the bankers. If all went well and the mine went ahead, then the contingent sales contracts became firm, but they fell away if the decision was negative. The Company was fortunate that during the whole period when its major mines were being developed, world trade was increasing rapidly and Japan was becoming a dominant industrial power. The Japanese supported many of the mines, including Hamersley Iron Ore, Lornex Copper, Bougainville Copper to name a few, with the basic long-term sales contracts that enabled their development. The Germans supported Palabora and to a lesser extent Bougainville. The mines were financed as individual projects generally with a loan/equity ratio of about 65/35, without legal recourse to RTZ for the loans. RTZ was, however, responsible for providing any capital overruns required to bring the mines into commercial operations. Nevertheless, the RTZ management regarded itself as morally responsible to the lenders because, Palabora aside, the sales contracts had either a fixed selling price (like Hamersley), an indexed price (like the Elliot Lake Uranium Mines and Mary Kathleen), or a floor price (as in Lornex, Bougainville and Rossing). Thus the Company believed that any financial failure would have been due to poor management or technical

Jan 1, 1985

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

Prof. J. W. Richards, South Bethlehem, Pa. (in reply to several questions):—The cut representing some of the round briquettes which were under test shows that, at the brcaking-stresses, they break into lumps, and do not disintegrate into powder. The process is simplicity itself. I have followed the different processes for sintering iron-ores and flue-dust, am interested in all of them and wish them all success; but this process appealed to me strongly by its simplicity. It is in line with a method which I once tried to work out myself, but which never came to anything, namely, the agglomeration of fine iron-ores by means of Portland cement. As small an amount as 5 or 6 per cent. of Portland cement will enable fine ore to agglomerate and set into a briquette, but when I came to estimate the cost, I found it was a little too high. The Schumacher process, curiously enough, does not work well on iron-ore, but flue-dust thus treated does harden and give a strong briquette. In my attempts to find a reason for this difference, it has occurred to me that possibly the particles of flue-dust had been coated over with some sublimed silica, which might be an agent in the setting. But I found by experiment that neither sublimed silica, nor ordinary silica, nor ordinary alumina, would briquette. Chemically pure iron oxide briquetted quite hard; but the application of pressure is a necessary part of the operation. If simply moistened with the solution and allowed to stand it does not set hard, but the more pressure applied to it the hardcr it sets. Evidently the flue-dust particles must be pressed very close together in order to get the small proportion of active material wet, so that the particles shall act at their points of contact; for it is evident that only at the points of contact does the cementing action take place. The reactions are facilitated by considerable pressure, bringing the acting particles close together, and may go on with

Jan 1, 1913

By Willis Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep ill Johan-nesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104° at sea level, insured reasonable safety, since all parts of the machine operated At subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By John Mills

THREE case histories from professions other than engineering will serve to introduce ideas basic to this discussion. Case (1) Date, about 1900. A young man, B. D. from a three-year graduate course in a prominent divinity school, was for two years a successful pastor of a small church; then friction over theological matters arose with a fundamentalist deacon of the "Bible belt" type. He resigned, returned to his university for a four-year medical course, interned for two more, and thereafter was successful and apparently happy as a physician. We may assume that he was converted in early adolescence and vowed himself to service as a minister. Acceptance of his announced career by parents, friends, and teachers plus his own determination confirmed his choice until illiberal criticism threatened his usefulness and he awoke to the fact that his inner needs were not along the direction in which inertia and his conscience had constrained him.

Jan 1, 1947