Search Documents

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By F. L. Kadey

The petrographic microscope is a well known tool in nonmetallic materials research. Its utility in the study of perlite is, therefore, not surprising. Valuable information has been derived on samples smaller than those needed by most other methods of analysis. Relatively little has been written about the petrographic analysis of perlite for two chief reasons: perlite is a material of relatively new commercial interest; and the independent prospector or expander, responsible for most studies, attacks the problem from an immediately practical viewpoint. Hence, petrographic studies of perlite have been limited to academic aspects. Rapid development of commercial interest in perlite has changed the situation. Mining and expanding companies now have effective research tools; and such instruments as the petrographic microscope have added materially to practical knowledge about this mineral. Petrographic techniques employed in the search for suitable deposits screen worthless samples rapidly and inexpensively compared with large-scale expanding tests. Hence, only samples of potential quality are selected for further testing. Field appearance of perlite reveals little about its true identity and practically nothing about its commercial significance. Consequently, any method that can be used to separate the "wheat from the chaff" is valuable. In addition to the conventional thin-section and immersion methods used in evaluation of crude perlite, petrographic microscope techniques have contributed to the study of expanded perlite. When apparently similar materials behave as differently in use as perlites, the internal structure of the individual particles becomes a subject of great interest. The purpose of this paper is to discuss some of the petrographic techniques used to characterize this material. WHAT IS PERLITE AND WHERE IS IT FOUND? Perlite was at first described as a glassy rhyolite possessing a pearl-like luster and exhibiting numerous concentric cracks resembling an onion skin appearance.' Fig. 1 is an illustration of perlite in this classical sense. Recently, its definition has taken on a commercial connotation: an acid volcanic containing 2 to 5% of combined water that, when heated rapidly to the softening point of the glass, coincident with the volatilization of the combined water, expands or "pops". Fig. 2, although hardly fitting the classical description given by Johannsen, is an excellent perlite in the commercial sense. It may occur as a breccia in rhyolite, (Fig. 3) and sometimes it is associated with obsidian nodules, as illustrated in Fig. 4. The term perlite includes the expanded product also. In the United States, perlitic rocks are restricted to the western part of the country. 2 Elsewhere in the northern hemisphere, European occurrences follow a belt beginning in Iceland and extending in a southeasterly direction through Scotland, County Antrim in Northern Ireland, and through the Massif Central of France, Germany, and Hungary; thence, into Italy and Sardinia, and through some of the Aegean Islands. A general oriental belt extends from Japan through Australia and New Zealand. Rhyolitic areas elsewhere in the world undoubtedly contain perlite.

Jan 1, 1963

By F. H. Wilson, M. L. Kronberg

The low temperature recrystalliza-tion of very heavily rolled copper produces a fine grained structure with a high degree of preferred orientation. Additional heating to within a few hundred degrees of the melting point may induce an abrupt and pronounced increase in the grain size, with the resulting crystals having new orientations. This behavior at high temperatures is commonly termed "secondary recrystallization." Several investigations have dealt with the phenomenon arid have served to bare many features of the beha~ior.1-4 In general,observations have been made on the sizes and shapes of the grains, and data have been presented showing the existence of an induction period in isothermal experiments. Although it has been well established that the orientation before the change is statistically (100) 10011, the so-called "cubically aligned" texture, there is no such agreement on the orientation after the change. For example, Dahl and Pawlek1 describe it as being equivalent to an approximately 30" rotation about the [l00] axis of the ideal cubic texture which is parallel to the rolling direction, the resulting orientation being near (210)[001]; and Cook and Richards2 find an orientation of approximately (110)[L12]. Since the completion of most of the work to be reported in this paper, Rowles and Boas3 have published their ver] illuminating paper on "secondary recrystallization," in which they present convincing evidence for a third orientation and show that their esperiments give no evidence for either of the other two orientations. The orientation is described as equivalent to an approximately 30° rotation about a [ 111] pole of the ideal cubic orientation. The existence of a variety of reported orientations is not unique for copper, for a similar state of affairs exists for other systems that have been studied— aluminum, nickel, nickel-iron alloys, and others. It seems therefore that the existence of this variety does not necessarily constitute a contradiction, but rather indicates that different experimental conditions yield different results. The fundamental nature of the phenomenon has not been elucidated. However, it has been generally recognized that the large grains could be the end product of growth of a few select grains already existing in the sample in minor amounts—too small to allow detection—or that entirely new ones could be formed by a process of nu-cleation and growth. Existing experimental evidence does not distinguish between these two most apparent possibilities. Nevertheless, the former has been more generally favored largely because our current understanding of the state of an annealed metal has not made it seem reasonable to expect a nucleation event to occur at temperatures above those required for the primary recrystallization. Observations on the Preparation and Heating of Twin-bearing Cubically Aligned Copper The starting material used throughout. the investigation was a bar of OFHC copper, forged and annealed at 950°C. Visual inspection showed the grain size to be around 0.5 mm, and did not disclose any preferred orientation. A chemical analysis showed the following composition: Cu + Ag— 99.99 Pct S — 0.005 pct 0 — <0.005 pct For the preparation of cubically aligned copper, ¾ in. thick slabs were cut from the bar, heavily pickled in concentrated HNO3 and cold rolled to sheets about 0.012 in. thick. The reduction in thickness was approximately 98.5 pct. Standardized annealing techniques were followed. Samples to be heated were lightly dusted with alumina in order to prevent sticking and then sandwiched between 1/16 in. copper plates. The resulting sandwich was heavily wrapped with copper sheet, and then annealed in air. The protection was such that only very thin films of oxide were formed. That the associated light oxidation of the samples had no specific effect on the recrystallization behavior was shown by the similar results that could be obtained on annealing in highly purified and dried hydrogen. Two methods were used in bringing samples to temperature: (1) by placing the package directly in the furnace at temperature and (2) by placing the package in the furnace at room temperature, and then slowly increasing the temperature. The corresponding heating rates are illustrated in Fig 1, and will be referred to as "rapid" and "slow," respectively. Unless specified otherwise, all anneals will be of the former type. Metallographic examination was made on samples prepared by electrolytic polishing and etching as described in the Metals Handhook.* STRUCTURES FOUND BEFORE "SECONDARY RECRYSTALLIZATION" OCCURS Annealing the rolled material for 1 hr at 400°C produced a heavily twinned, cubically aligned structure, the grain size being of the order of 0.03

Jan 1, 1950

By Thomas MacFarlane

I. INTRODUCTION. AMONG the industrial enterprises which have, from time to time, been undertaken in our Dominion, few have been more uniformly unsuccessful than those which have had for their object the development of our mineral resources. These resources have not been regarded as insignificant. On the contrary, it is supposed that we possess in our ore deposits something more than mere points of mineralogical interest. Some people are enthusiastic enough to believe that our mineral wealth will yet occasion the establishment in our backwoods of happy and industrious communities, causing, in fact, our wilderness to blossom as the rose. These enthusiasts do not shut their eyes to the serious obstacles which at every stage interfere with the carrying out of mining enterprises in this country, and which tempt one to believe that no such enterprise can ever be conducted to a desirable end, but they entertain the conviction that as our capitalists, miners, and technologists reach the years of discretion, and handle our mines in an economical, vigorous, and judicious manner, and as our statesmen become alive to the necessity of fostering, without extremely protecting, our metallurgical industries, mines and furnaces will gradually prosper, and so develop as to become a tower of strength to our agricultural, manufacturing, and mercantile interests. The fact that our past experience does not generally justify such glowing anticipations makes one all the more anxious to put on record the history of a successful mine, such as the Silver Islet has, on the whole, been. My connection with its discovery and early development was a very intimate one, and I propose in this paper to sketch its history and character, and sum up the amount of silver it has so far yielded. An additional reason for the appearance of this paper is that the Transactions of the Institute contain only a few references to the Silver Islet Mine. Although this mine is reported successful, we have, of course, no guarantee that it will not fall a victim to the same influences which have

Jan 1, 1880

By Jr. W. L . Phillips

The deformation and fracture characteristics of lithium-fluoride single crystals stressed in compression at room temperature have been studied. In as-cleaved specimens the stress-strain curves were variable; two types of {110} fractures were observed in the vicinity of kink bands. The stress-strain curves of annealed crystals were reproducible; {100} cracks formed which propagated along the (100) and (110) planes. The deformation and fracture characteristics were affected by quenching and X-ray irradiation. STUDY of the mechanical behavior of nonmetallic materials has received considerable impetus in recent years because of the need to overcome the problem of brittleness before the refractory properties of nonmetallics can be fully exploited. Ionic crystals provide a convenient and simplified starting point from which to study the deformation and fracture processes in nonmetallic materials. Early investigations of the mechanical behavior of non-metals were restricted largely to determinations of the crystallographic indices of the cleavage and fracture planes and the glide and twinning elements. Until recently, only occasional systematic studies of the deformation characteristics of non-metals have been made; and investigations of the forces necessary to initiate plastic deformation and the factors which affect the flow characteristics have been restricted largely to studies of sodium chloride&apos;-7 , magnesium oxides-l3 and lithium fluoride. 14-22 Fracture studies on alkali halide and metal oxide single crystals have been limited despite the fact that these materials have a number of advantages for fracture studies. Because they are transparent, the cracks which form can be viewed in three dimensions instead of in two dimensions as in metals. Also, they exhibit stress birefringence under polarized illumination, which enables the internal stress pattern and, therefore, the distribution of dislocations to be examined in the vicinity of the fracture. Early workers1-4 have shown that ionic crystals with a cubic structure fracture in tension along the (100) plane normal to the applied stress. These fractures were brittle at room temperature and propagated very rapidly across the cross section of the crystal. More recently, Stokes, Johnston, and Lil0 have studied crack formation in compressed magnesium-oxide single crystals. They found that the cracks, which were observed after about 3 pct strain, formed in the region of a kink band and lay on conjugate (110) slip planes instead of the usual(100) cleavage plane. Two different types of cracks were noted: stroh23 and secondary. The Stroh cracks did not exist merely on the surface but extended through the specimen in the form of tiny slits. A secondary

Jan 1, 1962

By Gifford White

CONSIDERABLE attention has been directed in recent years to methods of electric prospecting other than the conventional direct-current tech-niques. It has been extensively recognized that electrical data of a more general nature than that possible by direct-current methods might be useful in geophysical studies. To this end, a number of different types of electric currents have been employed, such as single-frequency alter-nating currents, square-topped periodic current waves,4 periodic surges of a less specific nature,8 and suddenly applied direct current.1,2 Yet, to the author&apos;s knowledge, little analysis of these different types of driving currents has been made from the standpoint of network theory to determine just what type of currents would give the most useful data, and, most important of all, to determine the relation of the data taken by one method to those of another. Without touching on the actual theoretical problem of how currents flow in the earth under specified boundary conditions, some very useful information can be obtained from the study of the fundamental integral equations of electrical networks, throwing light on the problem not ordinarily appreciated by the field worker. Some manipulation of the standard network equations will be made, with the sole purpose in mind of developing expressions leading to practical results. Suppose that four points in the earth have been located and it is wished to obtain the most useful type of electrical data by inserting current into two of them and measuring the potential developed between the other two. The first problem that arises is that of which pair of the four shall be chosen as current grounds. In the direct-current case, where only steady potentials are measured, the selection is of little consequence, but as soon as currents varying with time are used at the current grounds, a new effect arises. The fact that a varying current is flowing in the current-carrying conductor between the current grounds means that magnetic and electric fields varying with time will be produced

Jan 1, 1940

By G. D. Monk, W. C. Krumbein

The relation between permeability and the size parameters of unconsolidated sand is approached by considering sands as logarithmic frequency distributions having the basic parameters mean size and standard deviation. Sieve separates were mixed in accordance with the normal logarithmic probability law, so that the mean and standard deviation could be varied at will. Experiments were conducted in which one parameter was kept fixed and the other varied; in this manner the dependence of permeability on the individual parameters was evaluated. It was found that permeability can he expressed as the product of a power function of the mean size and an exponential function of the standard deviation. Earlier studies of the effect of size of particles on the permeability of uncon-solidated sand have shown that the permeability varies with the square of some average diameter. This was first pointed out by Hazenl in 1892 and verified by Slichter2 in 1898. Hazen&apos;s mean size was defined as the 10 percentile of the cumulative curve (i.e., size that is smaller than 90 pel cent of the distribution and larger than 10 per cent). Slichter&apos;s effective size, on the other hand, was found by Wilsey3,4 to agree with the 31 percentile. Fair and Hatch6 found that the geometric mean size of sieve separates yielded the same power function; Hulbert and Feben6 found that the permeability of sieve separates varied as the 1.89 power of the median diameter (i.e., the size associated with the 50 percentile of the cumulative curve). Relatively few studies included the effect of the "sorting" of the sediment on the permeability. It was recognized that the nature of the size distribution, in terms of the spread of the particles about the mean, affects the permeability, but no systematic investigations of this effect are known to the writers. Cloud7 demonstrated that the effect of the grain-size distribution on permeability is definitely measurable. In the present paper the authors investigate this relation analytically, and show that the effects of the size parameters on permeability may be predicted for at least a restricted set of conditions. Properties OF Sediments Recent investigations have shown that essentially all the geologically important characteristics of sediments may be expressed in terms of six measurable quanti-tities possessed by each clastic sedimentary particle. These attributes are: (I) size, (2) shape (sphericity), (3) roundness (angularity) , (4) mineralogical composition (density), (5) surface texture, (6) orientation. Each of these characteristics may be defined in several manners. Size may be expressed in terms of sieve mesh, settling velocity, volume, etc. Sphericity is a shape concept introduced by Wadell;8 it is essentially a measure of the ratio of the surface area of an equivalent sphere to the surface area of the particle. The same

Jan 1, 1943

By G. D. Monk, W. C. Krumbein

The relation between permeability and the size parameters of unconsolidated sand is approached by considering sands as logarithmic frequency distributions having the basic parameters mean size and standard deviation. Sieve separates were mixed in accordance with the normal logarithmic probability law, so that the mean and standard deviation could be varied at will. Experiments were conducted in which one parameter was kept fixed and the other varied; in this manner the dependence of permeability on the individual parameters was evaluated. It was found that permeability can he expressed as the product of a power function of the mean size and an exponential function of the standard deviation. Earlier studies of the effect of size of particles on the permeability of uncon-solidated sand have shown that the permeability varies with the square of some average diameter. This was first pointed out by Hazenl in 1892 and verified by Slichter2 in 1898. Hazen&apos;s mean size was defined as the 10 percentile of the cumulative curve (i.e., size that is smaller than 90 pel cent of the distribution and larger than 10 per cent). Slichter&apos;s effective size, on the other hand, was found by Wilsey3,4 to agree with the 31 percentile. Fair and Hatch6 found that the geometric mean size of sieve separates yielded the same power function; Hulbert and Feben6 found that the permeability of sieve separates varied as the 1.89 power of the median diameter (i.e., the size associated with the 50 percentile of the cumulative curve). Relatively few studies included the effect of the "sorting" of the sediment on the permeability. It was recognized that the nature of the size distribution, in terms of the spread of the particles about the mean, affects the permeability, but no systematic investigations of this effect are known to the writers. Cloud7 demonstrated that the effect of the grain-size distribution on permeability is definitely measurable. In the present paper the authors investigate this relation analytically, and show that the effects of the size parameters on permeability may be predicted for at least a restricted set of conditions. Properties OF Sediments Recent investigations have shown that essentially all the geologically important characteristics of sediments may be expressed in terms of six measurable quanti-tities possessed by each clastic sedimentary particle. These attributes are: (I) size, (2) shape (sphericity), (3) roundness (angularity) , (4) mineralogical composition (density), (5) surface texture, (6) orientation. Each of these characteristics may be defined in several manners. Size may be expressed in terms of sieve mesh, settling velocity, volume, etc. Sphericity is a shape concept introduced by Wadell;8 it is essentially a measure of the ratio of the surface area of an equivalent sphere to the surface area of the particle. The same

Jan 1, 1943

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world&apos;s annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months&apos; to several years&apos; duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis&apos; method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949

By W. J. Heck

The need for a better understanding of the effect of fluid pressure on the strength of intact and jointed rock has long been recognized. The behavior of pore fluid pressure was first pointed out by Terzaghi 1 who suggested the application of the effective stress concept to rock and concrete. While the effective stress concept has been used for some time in the design of mass concrete dams, it only recently has been applied to rock. Robinson 2 and Handin et al.3 evaluated the effects of pore pressure on a variety of sedimentary rocks and demonstrated the validity of the concept. Work using pore fluids other than water has been done by Boozer, et al.4 who considered strain rate and temperature as additional variables. According to the effective stress theory, the effective stress, [a], is the difference between the total stress, [a], and the pore pressure, u, and is the controlling factor influencing frictional strength of rock, other parameters remaining constant. Assuming the Mohr-Coulomb failure criteria applies, the shear strength, T, is given by the equation [r=d+ (a-u)tan ¢](1) where [~F], the angle of internal friction, and c, the cohesion intercept of "no load" shear strength, are the effective stress parameters.* Robinson,2 Handin,3 and others have demonstrated that moderately porous sand-

Jan 1, 1972

By Arthur E. Hall

Tax operation of "softening" in lead refining is designed, as the word implies, to separate from the bulk of the lead the elements that tend to make lead hard. These elements, which invariably are present in argentiferous lead, interfere with the desilverization, and must be almost entirely absent in refined desilverized lead. They are mainly copper, antimony, arsenic and tin. The properties utilized in accomplishing this separation are the low solubility of copper or copper sulphide in lead at its freezing-point temperature, and the greater and selective affinity for oxygen of the other elements at temperatures of the order of 700° to 900&apos; C., or, in the prcsence of sufficient, alkali, at a temperature of about 500&apos; C. The major problems of softening lead bullion lie in the necessary subsequent treatment of the by-products of the primary operation, which contain, either chemically or mechanically, lead or reagents that must be isolated for market or re-use. Therefore an important objective of the primary operation must be the highest practicable concentration of these elements in the by-products. Within the past three decades, during which the writer has been engaged in lead refining, the technique of softening lead bullion has had as many variations as there were lead refineries. This was the result of the variation in composition and character of lead bullion recived. The writer has received for refining shipments of lead bullion varying as widely as indicated by the following table: Sb, Per CEnt As. Per Cent Sn, Per Cent Cu. Per Cent Ag. Oz. per Ton 1.00 0.05 nil 0.05 70 0.50 2.50 2.00 0.50 200 3.50 0.50 nil 0.30 350 At times these have been received uniformly and at other times irregularly with a variation from week to week as wide as those shown. Under such conditions, establishment of a universal softening technique presented many problems. Such variations existed because refinery tolls too often were based on a ton of bullion, whatever its composition, and

Jan 1, 1937

By E. R. Hoskins

Results of a primary stress measurement investigation conducted on the 1100 copper ore body of the Mt. Isa mine, Mt. Isa, Queens., Australia, are presented in this chapter. The investigation started in September 1965, after discussion with the engineering staff at Mt. Isa, and consisted of both underground or in-situ tests at Mt. Isa and laboratory tests on Mt. Isa rocks and stress measurement techniques at the Australian National University in Canberra. Underground stress measurements were made in and adjacent to the 1100 copper ore body. The primary stress measurement site was in J 32 west crosscut on 14 Level. Approximate coordinates on the mine grid are 3000 north, 1650 east. The vertical depth below ground surface at this point is approximately 2180 ft. Some preliminary measurements were made in M 30 west crosscut on 13 Level, coordinates 3000 north, 2000 east, depth beneath the surface approximately 1990 ft. Additional flatjacks were installed on 11 Level in L 30 west crosscut, coordinates 3000 north, 2200 east, and depth beneath the surface approximately 1580 ft. All of the sites were in rock that from a mining engineering viewpoint must be considered extremely sound. The 13 and 14 Level crosscuts were approximately 14 ft on a side and nearly square and the 11 Level crosscut was approximately 10 ft on a side. All of the crosscuts had been standing open for several years and no artificial support of any type was necessary. Extraction openings hundreds of feet on a side have been made in this mine in similar rock and these have remained open also without additional support (see Davies 1 for a recent summary of mining techniques and conditions). The geology of the Mt. Isa mine has been most recently described by Bennett.2 Briefly, Mt. Isa is a silver-lead-zinc and copper mine in a series of Precambrian siltstones, shales, and bedded carbonates that strike north-

Jan 1, 1972

By C. S. Land

Relative permeability functions are developed for both two- and three-phase systems with the saturation changes in the imbibition direction. An empirical relation between residual nonwetting-phase saturation after water imbibition and initial nonwetting-phase saturations is found from published data. From this empirical relation, expressions are obtained for trapped and mobile nonwetting-phase saturations which are used in connection with established theory relating relative permeability to pore-size distribution. The resulting equations yield relative permeability as a function of saturation having characteristics believed to be representative of real systems. The relative permeability of water - wet rocks for both two- and three - phase systems, with the saturation change in the imbibition direction, may be obtained by this method after properly selecting two rock properties: the residual nonwetting-phase saturation after the complete imbibition cycle, and the capillary pressure curve. INTRODUCTION Relative permeability is a function of saturation history as well as of saturation. This fact was first pointed out for two-phase flow by Geffen et al. 1 and by Osaba et a1.2 Hysteresis in the relative permeability-saturation relation also has been reported for three-phase systems.3 Since saturations may change simultaneously in two directions in a three-phase system, four possible relationships arise between relative permeability and saturation for a water-wet system. The four saturation histories of this system were given by snel14 as 11, ID, DI and DD. I and D refer to the direction of saturation change (imbibition and drainage), with the first letter of the symbol indicating the direction of change of the water phase. As used in this paper, the second letter of the symbol refers to the direction of saturation change of the gas phase, i.e., D and I indicate an increase and decrease, respectively, in gas saturation. Only a few three-phase relative permeability curves have been published. Leverett and Lewis5 published three-phase curves for unconsolidated sand, and Snell4 reported results of several English authors for both drairrage and imbibition three-phase relative permeability of unconsolidated sands. Three-phase relative permeability curves for a consolidated sand were published by Caudle et a1.3 for increasing water and gas saturations (ID). Corey et a1.6 reported drainage (DD) three-phase relative permeability for consolidated sands. Recently, Donaldson and Dean7 and Sarem8 calculated three-phase relative permeability curves from displacement data on consolidated sands, also for saturation changes in the drainage direction. The only published three-phase relative permeability curves for consolidated sands with saturation changes in the imbibition direction (11) are those of Naar and Wygal.9 These curves are based on a theoretical study of the model of Wyllie and Gardner 10 as modified by Naar and Henderson.11 Interest in three-phase relative permeability has increased recently due to the introduction of new recovery methods and refinements in calculation procedures brought about by the use of large-scale digital computers. The scarcity of empirical relations for three-phase flow, and the experimental difficulty encountered in obtaining such data, have made the theoretical approach to this problem attractive. RELATIVE PERMEABILITY AS A FUNCTION OF PORE-SIZE DISTRIBUTION Purcell used pore sizes obtained from mercury-injection capillary pressure data to calculate the permeability of porous solids.12 Burdine extended the theory by developing a relative permeability-pore size distribution relation containing the correct tortuosity term.13 The works of Purcell and Burdine were combined by Corey14 into a form that has

Jan 1, 1969

By G. W. P. Rengstorff

In an effort to find an oxidation-resistant alloy of molybdenum, binary and ternary alloys containing aluminum, chromium, cobalt, iron, nickel, silicon, titanium, tungsten, vanadium, and zirconium were screened. Fourteen other alloying additions were also tested. Many of the alloys were more oxidation-resistant than molybdenum, but none were entirely satisfactory. MOLYBDENUM oxidizes extremely rapidly above 1450°F in air. At 1800°F, a loss of metal at the rate of 0.1 in. in 4 hr is typical. The high speed of this oxidation may be judged by comparison with the oxidation rate of 0.1 in. per year (0.00005 in. in 4 hr), sometimes taken as the maximum permissible oxidation rate at 1800°F for a satisfactory Fe-Cr-Ni alloy. Great strides have been made in the development of coatings and cladding to protect molybdenum from oxidizing atmospheres. These developments in surface protection will undoubtedly make it possible to take advantage of the excellent hot strength of molybdellum and its alloys in many new applications. Still, even the best coating can protect molybdenum only as long as the surface layer is unbroken. Research was undertaken to determine whether an alloy of molybdenum could be found which would resist oxidation. Such an alloy would not deteriorate suddenly when the protective surface layer was destroyed in a small area. In seeking an alloy of molybdenum to resist oxidation, the physical properties of molybdenum could not be sacrificed entirely. The development of an alloy with the desired resistance to oxidation was not achieved. The information obtained on the effect of a large number of elements on the oxidation of molybdenum is, however, of value in the development of coatings. Indeed, many of the alloys tested for oxidation resistance were already known to have poor mechanical properties but were tested to aid in the development of coatings. Oxidation of Molybdenum The rapid oxidation of molybdenum is usually attributed to the volatility of Moo,,. Gulbransen and Wysong have shown that molybdenum oxidizes very slowly up to 850°F, the temperature at which the oxide film begins to evaporate. Melting as well as evaporation of molybdenum oxides promotes the oxidation of molybdenum. MoO melts at 1465°F. MOO, the oxide which is believed to form at the metal-oxide interface, combines with MoO, to form a eutectic having a melting point of 1432°F.&apos; The liquid oxide, even if nonvolatile, could cause poor resistance to oxidation by allowing easy transport of molybdenum and oxygen ions through the oxide. Actually, a sudden increase in the rate of oxidation of molybdenum at 1460°F has been observed to coincide with the appearance of a liquid phase. The formation of a volatile oxide is not unique with molybdenum. The problem is also encountered with vanadium, tungsten, and some of the Pt-Pd group of metals. Vanadium not only forms the volatile V2O3 but, like molybdenum, forms a liquid oxide coating. Few attempts have been made, however, to prevent the rapid oxidation of these metals by alloying. Oxidation of Molybdenum Alloys At the beginning of this work, very little was known of the oxidation resistance of molybdenum alloys. It was known that molybdenum disilicide (with 37 pct Si) has extremely good oxidation resistance,&apos; but this compound is so brittle that it has few uses. It is an effective protective coating for molybdenum when allowance can be made for its brittleness. Chromium was known to retard the oxidation of molybdenum,&apos; but at least 50 pct Cr was necessary to have an appreciable effect. Other, unpublished, reports show that a few other alloys have been given preliminary tests, but the results have not been promising." Choice of Alloys to be Investigated An alloying element might be expected to protect molybdenum in either of two ways: Its oxide might combine with molybdenum oxide to form a stable, nonvolatile complex oxide (a molybdate); or the oxide of the alloying element might form in preference to molybdenum oxide, developing an impervious layer which would prevent the formation of a volatile molybdenum oxide. The knowledge available about the formation of molybdates was meager. Therefore, the initial study was made on alloys of molybdenum with elements having especially stable oxides. On this basis, binary and ternary alloys containing the following six elements were investigated: aluminum, chromium, titanium, zirconium, silicon, and vanadium. Nickel was also added as an alloying element. Although it does not form a more stable oxide than molybdenum, it does impart some oxidation resistance to copper and iron. Its inclusion in the study was fortunate because its alloys proved to be the most promising of those first tested. Apparently nickel formed a stable molybdate. Because nickel was effective in reducing the oxidation rate of molybdenum, the elements iron, cobalt, and tungsten were added to the list. The ten alloying elements mentioned form ten binary and 45 ternary alloying systems with molybdenum. A series of alloys was tested in each of these systems. In addition, at least one test was made on the effect of each of the following alloying elements:

Jan 1, 1957

By C. L. Horn

All the tunneling machines discussed in this chapter are Calweld machines. I have divided the machines designed for soft-to-medium formations into three groups, correlated with typical formations and estimated compressive strengths: 1) Running sand and silt requiring blade cutters. 2) Chalk and clay, requiring drag-type cutters, for compressive strengths ranging from 0 to 2000 psi. 3) Sandstones, hard clays, and limestones, requiring disk cutters, for compressive strengths ranging from 2000 to 20,000 psi. All of the soft-to-medium-formation machines are powered by electric hydraulic or diesel hydraulic pumps. The pumps in turn drive hydraulic motors for the torque reaction. The soft-to-medium-formation machines are enclosed in a 360º shield with a cutting shoe, a center portion of the shield housing the mechanical equipment, and a tail shield. Tunnel supports are usually required, and the supports are normally erected in the tail shield. Our first machine was built in 1963, and all but five of the machines illustrated in the figures with this chapter were built in 1966 and 1967. Some of the machines manufactured will be discussed in the following sections; specific features as development has progressed will be pointed out. HARD-ROCK MACHINE The Calweld hard-rock machine has been designed along basic and accepted principles for a hard-rock mechanical borer. The features of this machine are as follows: 1) Direct electric motor drive through a planetary gear reduction ring and pinion gear, and then to the cutting head through a hollow drive shaft.

Jan 1, 1970

By P. B. Bucky

In previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravitational forces, will behave similarly to its prototype if the model and prototype material are the same and the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at hill and its effects noted. Experimental work on a small-scale model may therefore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but arc to be interpreted as

Jan 1, 1934

By A. H. Geisler, F. Keller

Some of the important changes that take lace in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrys-tallization. Although improved metal-lographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based 011 the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mah13-l7 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chcmical or anodic treatment. .After removal from the metal sample by one of the special techniques described by Evans,l9 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,l7 nicke1,7 iron3,8,9 and a nickel-beryllium alloyl1 by heating; films formed on iron8,9 by chemical action; and films formed on aluminum3-&apos;" by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By F. Keller, A. H. Geisler

Some of the important changes that take lace in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrys-tallization. Although improved metal-lographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based 011 the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mah13-l7 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chcmical or anodic treatment. .After removal from the metal sample by one of the special techniques described by Evans,l9 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,l7 nicke1,7 iron3,8,9 and a nickel-beryllium alloyl1 by heating; films formed on iron8,9 by chemical action; and films formed on aluminum3-&apos;" by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By Attilio Ligasacchi

The production of magnetite in copper smelting has been the subject of wide investigation in the past.1-9 It is accepted that most of the magnetite is produced in the converters and returned to the re-verberatory furnace with the converter slag. Part of this magnetite is circulated back to the converters in the matte. As a result, if proper fluxing practice is not followed, and temperatures in the converting process are not strictly controlled, an undesirable circulating load of magnetite may occur. This might ultimately lead to saturation in the reverberatory bath with consequent settling of the magnetite at the furnace bottom. This paper contains the cumulative results of a series of investigations on the formation and control of magnetite presently being conducted by the metallurgical department of the Chino Mines Division of Kennecott Copper Corp. THE METHOD USED FOR THE DETERMINATION OF MAGNETITE AND OTHER MAGNETIC MATERIALS Conventional wet chemical magnetite analyses are neither reproducible nor theoretically sound. These analyses are sensitive to time, temperature, and heating rate-all factors which tend to decrease their accuracy and reproducibility. To overcome the unreliability of the above method, H. W. Mossman1 developed an inductance bridge magnetite "meter" which completely replaces the wet chemical analysis with the advantage of quicker and reproducible results. Fig. 1 is a schematic diagram of the meter in use in the Chino metallurgical laboratory. When a pulverized specimen with magnetic properties is placed in coil A of the inductance bridge circuit, the permeability of the core is increased, causing a voltage drop across the coil. The unbalance is amplified to operate the balancing motor which adjusts the movable iron core in coils C and D to bring the bridge back to balance. An indicator arm connected to the movable iron core indicates directly the percent, or weight, of the magnetic material in the specimen. Coil B acts as a reference coil and a zero adjustment. The meter is standardized with a set of various amounts of -100 mesh pure magnetite crystals (99.8 pet Fe3O4) thoroughly mixed in a test tube with -100 mesh quartz sand. These mixtures are combined with inert transoptic powder and heated to 140° to 160°C (melting point of the powder) and subsequently cooled to room temperature, solidifying the whole mixture, in this manner eliminating any possible preferential orientation of the magnetite grains. In order to determine the effect of the particle size" of the magnetite and other magnetic materials on the meter determinations, five size fractions were obtained by wet screening of the 99.8 pet pure magnetite and several reverberatory matte and slag samples. The following size fractions were investigated: -80 + 100; -100 + 150; -150 + 180; -200 + 250; -250 + 300 and -100 mesh. The deviation of the meter readings for the various sizes of each sample never exceeded ±0.3 pet. This deviation is considered well within the accuracy needed for common smelter operation procedures. Further investigation proved also that grinding slag and matte samples in our laboratory disc grinder normally produced a powder constituted of 95 pet -200 + 300 mesh. For practical purposes a - 100 mesh size was used as standard for our studies. It was also found that for rapid determinations tamping of the sample in the test tube was sufficient and gave comparable results with those samples solidified with transoptic powder. For the purpose of this study we define the magnetite content in copper smelter slags and matte as the equilibrium amount of crystalline Fe3O4 existent in the specimen at a given reference temperature, excluding any secondary magnetite precipitated in the specimen during nonequilibrium conditions. MAGNETITE DETERMINATION IN SLAGS Since it is impossible to ascertain the status of equilibrium of a conventional slag sample, due to

Jan 1, 1965

By William Newnam

WHEN Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great anti the tonnage was small, but on the other hand the results were fairly, satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Roan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process.. The Luce and Rozan process has persisted in its original form to the present clay. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process.

Jan 5, 1917