Search Documents

By J. N. Hummel

THE methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view, The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic.

Jan 1, 1931

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By Bruce T. Stanley

A key point in the design and operation of a modern mining operation is the construction of what is called an ore-body model or block model. This model is a representation of reality constructed from predicted information. The blocks involved are merely subsets of the overall model which allows manipulation of the contained information on a local scale. In general, block models enable mine planners to effectively select the most promising means of extracting the ore both physically and economically. The uses of a block model can be quite diversified, but one must realize that a single model that satisfies all curiosities and forms of expertise is difficult to construct.

Jan 1, 1979

By C. F. Rust

Experimental evidence is presented showing that reproducible formation resistivity factor measurements and resistivity index determinations on reservoir core samples map be made utilizing either the two- or four-electrode methods. Equipment is described which permits the application of either technique to the core specimen without loss of time and with a minimum amount of effort. Since electrical resistivity measurements on reservoir rocks are important not only in electric log interpretations, but also in the study of fundamental rock parameters, it was considered desirable to compare the applicability of both techniques of resistivity measurement. INTRODUCTION The techniques employed in the measurement of electrical resistivity on reservoir rocks, as practiced in the petroleum industry, may be reduced to two fundamental methods: one utilizing two electrodes only, usually referred to as the two-electrode method; the other using two additional electrodes and commonly known as the four-electrode method. In the former, the core sample whose resistivity is to be measured is mounted between two electrodes, usually metal discs, which serve to pass a current of known magnitude through the saniple. The potential drop across the sample, measured between these same two electrodes, and the core dimensions furnish the necessary data to compute he resistivity of the sample. In the four-electrode technique the end plates, again usually ol metal, still serve as current electrodes. Additional probes or electrodes dispersed along the sample are utilized to measure the potential drop. Both methods are used in practice1,2 and it is the purpose of this paper to compare the two techniques as applied to the determination of formation reiistivity factors and the resistivity index exponent n, in Archie's empirical equation I = p/po = Sw 11. To evaluate the two techniques it is desirable to point out the experimental precautions which must be taken to insure reliable results. It is evident from the electrode arrangements of the two- and the four-electrode methods that, for a given sample, the volume of sample included by the four-electrode method is less than the volume included by the two-electrode method. One of the prime difficulties associated with the two-electrode method is the possible occurrence of an abnormally high resistance between the electrodes and the brine-saturated sample, which results in erroneous resistivity values for the core sample itself. Attempts to alleviate this difficulty meet varying degrees of success. Methods used in the past employ such absorbent materials as brine-saturated Kleenex: chamois, or felt. A technique described by Morgan, Wyllie, and Fulton,1 appears to be more satisfactory. Their method consists of spraying or painting the end areas of a core sample with conductive silver paint. This technique reduces contact resistances between the porous medium and the electrodes to a value which is generally negligible as compared to the resistance of the sample itself. In the four-electrode method these requirements are not as stringent since separate probes are used to measure the potential difference acrozs a portion of the sample. In this case, contact resistance occurring at the current electrode; are of no consequence. and those appearing at the potential

Jan 1, 1952

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix.

Jan 11, 1951

By G. R. Leverant, C. P. Sullivan

Re crystallized TD-nickel mi-2Th0,) in both coated und uncoated conditions was fatigued at 1800°F at total strain ranges varying .from 0.2 to 0.75 pct. The fatigue life of uncoated inaferal, Nf, was related to the total strain range, ?eT, by (2Nf/021AeT = 0.014. A duplex Al-Cr pack coating increased the fatigue life by about a factor of two. The cracks that led to failure in both coated and uncoated material were initiated at the outer surface, indicating that the mechanical properties of the surface layers were important in determining fatigue life. Crack propagation and subsurface crack initiation in the TD-nickel occurred preferentially at grain boundaries with cavitation at thoria particle-matrix interfaces an integral part of the grain boundary fracture process. The importance of both the grain morphology developed during thermome chanical processing of TD-nickel and the distribution of thoria particle sizes to fatigue resistance are discussed. THE fatigue properties of only a few dispersion-strengthened metals have been studied at temperatures 0.5 Tm;1,2 among these have been lead and aluminum containing oxide dispersions. TD-nickel is a material of interest for application in aircraft gas turbine engines, but little fundamental information is available on its behavior under cyclic loading conditions. In this study, the low-cycle fatigue properties of TD-nickel were determined at 1800°F with emphasis on the 101-lowing; 1) the relation of the grain morphology produced during thermomechanical processing to crack initiation and propagation; 2) the role of thoria parti-cles in the fracture process; and 3) the effect of an oxidation resistant coating on fatigue life. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in. thick plate which had been subjected to a proprietary series of thermomechanical treatments with a final anneal at 2000°F for 1 hr in hydrogen. The composition of the material is given in Table I. At the test temperature of 1800°F, the 0.2 pct offset yield stress was 15,000 psi, and the elongation and reduction in area were 4.6 and 3.0 pct, respectively. The microstructure of this material has been previously described.&apos; Briefly, it consists of an array of lath-shaped grains, about 0.15 mm in thickness, with the long dimension of each grain parallel to the primary working direction, Fig. 1(a). The presence of very small annealing twirls, Fig. l(b ), together with the absence of extensive dislocation networks, Fig. L/C), indicated that the material was in the recrystal- Table I. Composition of TD-Nickel ThO2 2.3 vol pct C 0.0073 wt pct lex 0.01 wt pct Cr 0.01 wt pct Cu 0.004 wt pct S 0.001 wt pct Ti <0.001 wt pct Co <0.01 wt pct Ni bal lized condition. Commercial TD-nickel sheet has a similar grain size and shape, but unlike the present material is not recrystallized as evidenced by the absence of annealing twins and the presence of a well-developed dislocation substructure.4 The plate material had Young&apos;s moduli in the rolling direction of 22 x 106 psi and 13 x 106 psi at room temperature and 1800°F, respectively, indicating a texture with a strong {100}<001> component in agreement with previous observations on recrystallized TD-nickel sheet.596 The 2.3 vol pct of thoria particles were uniformly distributed although some clustering and stringering of larger particles was occasionally seen. The average diameter of the particles was 450 and the calculated mean planar center-to-center spacing was 2100Å. Two specimens were coated with a duplex A1-Cr pack coating. The coating was somewhat nonuniform from one position to another along the gage length. An area of the coating after testing is shown in Fig. 2. Electron microprobe analysis revealed the following zones in the various lettered regions indicated in Fig. 2: A) a bcc matrix of B-NiA1 with some chromium in solid solution along with a fine dispersion of a chromium-rich second phase which was probably precipitated during cooling from the test temperature to room temperature; B) fcc y&apos;-Ni,Al with some chromium in solid solution; C) porosity; D) a two-phase mixture of a chromium-rich solid solution containing nickel and aluminum and a small volume fraction of a nickel-rich solid solution having approximately the same composition as the immediately adjacent portion of region E, E) the TD-nickel substrate containing chromium in solid solution to a depth of 5 to 10 mils. As expected from the nature of the diffusion processes involved,7 the thoria particles were present only up to the layer of porosity, region C, Fig. 2. The measured thickness of the coating proper, zones A to D, after testing was 1 to 2 mils. The specimen design and testing techniques have been previously discussed.&apos; Stressing was axial and parallel to the lath-shaped grains (i.e., parallel to the rolling direction). The total strain range was controlled between zero and a maximum tensile strain varying from 0.2 to 0.75 pct. (The test at 0.2 pct total strain range was switched to load control at 1030 cycles at which point the peak tensile and compres-

Jan 1, 1970

By H. W. Knott, M. H. Mueller

The crystal structures of Ti2Cu, Ti2Ni, Ti4Ni2O, and Ti4Cu20 have been determined using powder specimens examined by X-ray and neutron diffraction. Lattice constants have been determined for all four phases using X-ray powder diffraction films. Atom positional parameters of all four phases have been determined from observed neutron intensities. X-ray diffraction calculated intensity data have been presented also for the phase Ti2Cu to point out the particular suitability of neutron diffraction in this case. Interatomic distances have been determined using the positional parameters obtained from neutron diffraction. ALTHOUGH some investigations of the crystal structures have been made of these four compounds previously,&apos;-13 it was the purpose of the present investigation to expand the previous work in order to locate the various atoms, determine their coordinates, and to confirm or to correct some of the previous work. It was convenient to group these four compounds together since they are related chemicallv and/or structurally. The compound Ti2Cu is tetragonil; and Ti2Ni, Ti4Ni2O, and Ti4CU2O are all large fees of the same space group. Ti2Cu has been previously reported as a fee phase by Laves and Wallbaum;1 and Rostoker2 which was possibly the oxide phase, Ti4Cu20. Joukainen, Grant, and Floe;3 and Trzebiatowski, Berak, and Ramotow-ski4 have also reported a phase of this composition. karlsson5 has reported a small fct phase of the composition Ti3Cu which may be the presently discussed Ti2Cu phase. More recently Ence and Margolin6 have reported a small fct phase for Ti2Cu and the present authors7 together with Nevitt8 have briefly reported it to be a bet related to the fct with a co three times the length of the co of the fct and have also reported that this phase has a very limited composition. Further refinements will be reported which have varied some of the parameters of this bct structure slightly. Ti2Ni has been reported as a fee phase by Laves and wallbaum;1 Duwez and taylor;9 Rostoker;2 Poole and Hume-Rothery;10 and Yurko, Barton, and parr.11 In a later paper Yurko, Barton, and parr12 have given the complete structure of this phase based on an X-ray diffraction study which was independently confirmed with neutron diffraction by Mueller and knott.7 Additional crystal structure information will be given. Ti4Ti2O, Ti4Cu2O, and a number of other compounds including Ti4Fe2O have been reported as fcc phases by Rostoker,2 and more recently Nevitt13 has confirmed the Ti4Ti2O phase. Rostoker,2 however has reported diffraction lines for Ti4Fe2O which do not have all odd or all even indices. These lines, therefore, cannot be observed if this compound has a fee structure. This same error has crept into the diffraction results reported for TiNi2O and Ti4Cu20 in the ASTM powder data which has been credited from Rostoker&apos;s data. Complete crystal structures of these two phases will be presented. Although all four of these structures have large unit cells and hence do not lend themselves for completely resolved neutron powder patterns, a sufficient number of individual reflections was observed for solving the structure. They also serve as good examples of some of the advantages to be gained by using both neutron and X-ray diffraction techniques. EXPERIMENTAL PROCEDURE All of the alloys were prepared by arc melting. The starting metals had the following purity: Cu 99.999 pct, Ni 99.83 pct, and Ti 99.92 pct. Oxygen was introduced into the two oxide phases as chemically pure TiO2, with the remainder of the titanium coming from the above mentioned metal. All of the sample buttons were annealed in evacuated Vycor tubes, the two binary phases for 5 days at 700°C and the two oxide phases for 3 days at 900°C. Oxygen analyses were performed on all four phases by two independent laboratories with the following amounts of oxygen present in atomic percent; Ti2Cu-0.06, Ti2Ni-1.03, Ti4Ni2O-13.95, and Ti4Cu20-13.87. The stoichiometric amount for the oxide phases is 14.29 at. pct. Since all of the samples were very brittle they were easily reduced to a powder for diffraction measurements. The lattice constants given in Table I were determined for the four compounds from X-ray diffraction patterns of powder samples exposed to filtered copper radiation using a 114.59 mm diam Debye-Scherrer type camera using the Straumanis loading. None of the patterns showed a detectable amount of a second phase. The lattice constants were obtained from an IBM 704 computer program employing a least squares treatment with systematic correction terms as previously reported.14

Jan 1, 1963

By B. F. Fackenthal

One of the practical questions presented to the blast-furnace manager, with regard to which little help can be obtained from existing technical literature, is the manner of filling and blowing-in. This operation is often performed according, more or less, to traditions which have come down from earlier practice, and which, if not positively detrimental when followed with the large modern furnace, may at least be greatly improved, just as the running of the furnace itself, while in blast, has been improved. It is not necessary, as many of the old furnace-men believed, to make a lot of white or silver-gray iron at the start, or to spend many weeks, or months even, in bringing the furnace to its normal burden. It has seemed to me that the publication of carefully-recorded data of practice on this point may be interesting to the members of the Institute engaged in the management of blast-furnaces. The enlarged blast-furnace at the Durham Iron Works, Riegelsville, Pa., owned by Messrs. Cooper & Hewitt, of New York City, was first put in blast February 21, 1876, since which time it has made seven blasts, and is now running on the eighth. A description of the furnace-plant, together with a record of the fifth blast, was given in my paper read at the Chattanooga meeting, May, 1885 (Transactions, xiv., 130). After some of the early blasts the furnace-lines underwent considerable change, and I have thought best to accompany this paper with drawings showing the lines and the tuyere-arrangement (see Plates I. and II.), and to give also the following summary of the conditions and results of each blast. During the first and second blasts no coke was used, and the furnace ran very irregularly, showing a constant tendency to scaffold, which was attributed, in great part, to the small hearth and other defective lines. The large proportion of air required at this furnace is accounted for by the fact that the engines are defective, and do not deliver into the furnace the amount of air indicated by the pistondisplacement.

Jan 1, 1890

By H. H. Einstein

Swelling ground is one of the most feared problems in tunneling. Although usually not causing sudden failures during construction, the very large and longlasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners up to 1 m (3 ft) thickness that have been cracked or crushed, tunnel inverts that are heaving at 0.1 m (0.3 ft) per week during construction and continue to heave during decades. This paper summarizes essential components of design construction procedures where tunnels in swelling rock can be built to perform satisfactorily. It is important to point out that design and construction cannot and should not be separated. The way the tunnel will be built has to be an integral part of the design. Swelling can be defined as time dependent volume increase and is distinguished from squeezing, another time dependent phenomenon occurring in tunneling. Squeezing involves exceeding the shearing resistance while swelling usually does not. Swelling of rock masses can occur as swelling of the intact rock, swelling of wall rock, of gouge and of filler in the discontinuities of a rock mass, and as a combination of the above. Swelling mechanisms have been discussed elsewhere (ISRM 1983).

Jan 1, 1984

By E. H. Kelton

THE purposes of this paper are to describe the use of adjustable cut and draw tools as a control test of drawing properties and to point out that no other well-known test or combination of tests determines this quality in zinc and zinc alloys. Rolled zinc has been used for making drawn articles, particularly battery cans, for many years. The development of rolling treatments satisfactory for, these purposes followed the usual course of trial and error experimentation depending upon cooperation with customers to determine what type of material was suitable. A quick test of drawing quality was highly desirable, of course. Scleroscope hardness and temper,1 having no apparent relation to drawing quality, were used simply to check the duplication of rolling treatment and grade of metal. The dynamic ductility1 test, on the other hand, was believed to be so like the drawing operation as to provide a reliable index and came to be taken as the criterion of good drawing properties. Faith in this test was strengthened by the fact that metal having the highest ductility was more satisfactory for operations, such as the manufacture of battery cups, that required several redraws. No distinction was made at that time in specifying metal as to whether it was to be subjected to simple cut and draw, redrawing or forming operations. It developed, however, that in some grades of metal the highest ductility did not coincide with the most satisfactory quality when the material was used for a single draw.

Jan 1, 1934

By J. W. Leonard, B. A. Donahue

A method is described for incorporating coal petrography into mining and preparation plant quality control based on conventional analyses. Complete analyses are made of each of the uniform and relatively distinct petrographic bands in a coal face. With this information it is possible to develop petrographic standardization curves. These curves permit diverse coal characteristics to be rapidly monitored by application of a few standard coal tests. Single seam quality control is discussed in this paper. Inquiries continue to be made about coal petrography, and specifically, about whether coal petrography should be applied more extensively in the coal industry. Coal petrography is the study of the distinct physical, optical, and chemical increments which make up the organic rock mixture which we know as coal. Petrography can be applied by any coal company or at any coal mine where conventional coal analytical facilities are available and where additional resources can be allocated for an increased number of determinations. This first paper of a two part series includes (1) a proposed conventional approach to single seam petrography based on the development of petrographic standardization graphs and (2) some informative and supplemental interrelationships involving coal characteristics developed as a result of this research. In the second part of this series, to be published at a later date, those petrographic characteristics of bands taken from many different coal seams located over wide geographic areas which can be closely related to each other will be considered. These findings will be examined looking toward the development of a comprehensive, conventional approach to coal petrography which can be used as a common basis for multi-rank petrographic standardization graphs. Implicit to the understanding of coal petrography is the well established fact1,2 that the individual analyses of distinct petrographic bands often differ widely from the average analysis which is used to characterize a whole coal seam. In fact, a distinct and minor banded increment of coal in a high volatile seam may actually be a medium or low volatile coal with an analysis similar to the average analyses of seams located in distant coal fields. During the mining of coal, much degradation is caused which tends to randomly scatter coal bands. The degraded, scattered, and physically separated constituents of distinct petrographic bands are processed side by side in the coal preparation plant as distinct petrographic fractions with particles grouped according to a narrow size range (which derives in part from common hardness), specific gravity, and-or surface chemistry. Tile data obtained from numerous analyses made on each of the bands of any given coal seam, although diverse, can be readily interrelated. Indeed, these interrelationships can be developed into a series of nomographs or petrographic standardization graphs to serve as a basis for developing a conventional petrographic* program. Thus, by analyzing one property (for example, ash) of a selected petrographic fraction collected or separated from the flow of coal in a preparation plant, it should be possible to estimate the other physical, chemical, and thermal properties of this fraction by referring to the petrographic standardization graphs. It follows that any or all petrographic fractions in the total coal flow originating from a single coal seam can be rapidly monitored for many properties on the basis of a single analysis run on each fraction. In recent years coal petrographic research has concentrated heavily on that phase of this work which involves microscopic reflectance measurements made at many minute and selected points on a coal briquette surface.3,4 Thus, the percentage of the total number of reflectance measurements that fall into each of a consecutive series of arbitrarily chosen reflectance classes are used to characterize coal. This procedure is analagous to using the face of a coal briquette to represent the reflectance characteristics present at the face of a coal seam. Moreover, by analyzing petrographic fractions of known and uniform optical properties it is possible to closely relate reflectance to other coal characteristics. For example, reflectance has long been known to be related to such

Jan 1, 1968

By C. C. Harris

A critical literature review leads to a descriptive model of tumbling mill operation based upon energy partition concepts and the necessary requirements for particle fracture. As grinding proceeds into the ultra-fine region, conditions which are of little significance during normal operations gradually become controlling. These involve increasing resistance to fracture and an increasing tendency to aggregate as particles become smaller, and a growing fraction of the power input being consumed fruitlessly. The result is that fineness asymptotes to a maximum value as comminution proceeds indefinitely; thus where t is time, p and n are experimentally determined parameters, and Ø is a measure of fineness, which is presumed to be proportional to specific surface area, or proportional to the reciprocal of the size modulus (provided that the distribution modulus remains constant with time), or both. Ø, is the asymptotic value of Ø and is a measure of the grind limit. A method for its graphical determination is given. In a previous paper1 the physical and mathematical principles requisite to a study of the role of energy in comminution were reviewed. The micro-process of comminution — or the comminution event — can be investigated in terms of (a) the magnitude of the force-field localized around the individual particles which gives rise to the stresses generated in the particles, which in turn induces their fracture, and (b) the distribution of fragment sizes, should the event prove fruitful. The entire fragmentation operation can be considered to be the totality of its individual events, and in order to obtain a single independent variable of the process it is necessary to transform and sum the local stresses in terms of energy.1 This energy, however, will account for only a fraction of the energy input to the comminution process, the actual magnitude depending upon the kind of mill and several related factors. From the comminution viewpoint the primary function of a mill is that of stressing as many as possible of the individual particles of the charge to failure, with the maximum economy of energy expenditure. This is difficult indeed to achieve, for stressing a particle does not always break it, while the overwhelming portion of the energy input is involved with various internal mill processes which — almost incidentally — determine the magnitude, frequency, and manner in which the forces are applied to the particles. Essentially, these processes depend upon the mill dimensions, loading and speed, and they may be little affected whether fracture occurs or not. These processes must be delineated if a complete description of the role of energy in comminution is to be given; the energy account sheet1 (Fig. 1) in showing how the energy is partitioned for the requirements of the several functions it performs, provides a framework for the development of a model of the comminution process. Actual numerical values for the variables appearing in Fig. 1 will depend upon the mill, materials, and operating conditions. A possible general relationship between the variables will be suggested in this paper. Before proceeding further, a cautionary note must be issued. It was pointed out in an earlier paper&apos; that while energy input is not changed by increasing the power and decreasing the time in the same proportion, and vice versa, the results of the process in terms of particle fineness may be different. Thus, although energy is chosen as the independent variable of a comminution process, it is not absolutely independent, and care must be exercised to ensure that it is used within its range of valid application. Time has the necessary independence, and it will be used in place of energy where it is appropriate. The residence time in a mill is usually of the order of minutes. Under these conditions the particles are subjected to "... a relatively constant fracture producing environment".2 However, under the more rigorous conditions of greatly extended time, which pertain in ultra-fine grinding, indications are that the fracture producing environment no longer remains constant; this is the major subject of this paper. At this extreme limit the mill is probably taxed to its utmost, and at the same time the bulk material properties are becoming closer to ideal, while the physico chemical effects associated with surfaces, edges and corners are multiplying. (The edge length per unit volume is proportional to the square of the specific

Jan 1, 1968

THERE are two general types of scientific approach to a problem. One approach, which is the more widely known, involves an analysis of the situation at the beginning of the experiment; this is followed by an analysis of the situation at each instant of time during the experiment and leads to a-detailed description of the prevailing conditions at the end of the experiment. Suppose, for example, we wish to predict the final rest position on a billiard table of a ball moving initially in a certain known direction with a known speed. The obvious approach is to estimate or measure off its course by consideration of angles of rebound, taking account of the "English" or spin if necessary and finally estimating from experience (or calculating from coefficients of friction) the slowing down occasioned by friction, thus establishing the point of the course at which the ball may be expected to stop. Any interference with the calculated course occasioned by collision with an unanticipated object would obviously cause us to revise drastically our estimate of the rest position. This general method of approach characterized by detailed description of how one situation developed from another seems intuitively appealing and is the most widely known method. There is no doubt that it gives very satisfying results when it can be used. There is a second general method of approach. In this method, the final state of a system is predicted from knowledge of general broad principles and their application, considering only the restrictions imposed upon the system. It is unnecessary to follow the course in detail; intermediate steps are not even considered. For example, if the billiard table mentioned in the first paragraph were tilted to one corner, one could predict that the final resting place of the ball would be in that corner; this prediction can be made independent of any particular course the ball may follow. This second general method of attacking problems is the one used in thermodynamics. There its use is so outstand-

Jan 1, 1951

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946

By Howard N. Evanenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. AVERAGE RECOVERY The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered-it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal-is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1946

By W. W. Smeltzer

The linear formation rates of wustite films have been determined over the temperature range 590° to 1030°C using a vacuum microbalance technique. These rates are dependent directly on the partial pressure of carbon dioxide, Activation energies for film and scale formation in carbon dioxide and oxygen atmospheres are equivalent to either the dissociation energies of carbon dioxide and oxygen, or the activation energy for the diffusion of cation vacancies in wustite. Of the metals, iron is the most widely used basic constituent of durable alloys despite its intrinsic property of converting at a relatively rapid rate to the oxides from which it is derived. This property has accounted partially for many investigations on the oxidation of iron at low and high temperatures. Interpretation of the results have been complicated by formation of multilayers containing the various oxide phases. To aid in elucidation of the oxidation kinetics, measurements have been carried out in this investigation on the growth of the wustite surface layer. There are several studies directly related to the objective of this investigation. The growth of multilayer scales has been demonstrated to be diffusion controlled in oxygen at atmospheric pressure over the temperature range 450" to 1200°C by Davies, Simnad, and Birchenall.&apos; To gain an insight into the diffusion mechanism, Himmel, Mehl, and ~irchenall&apos; determined the self-diffusion coefficients of iron in wustite, magnetite, and hematite. These results were used to evaluate the oxidation rates of iron and its oxides, taking as a basis the theoretical parabolic rate equation developed by Wagner., The evaluations were compared to experimental data and were shown to provide essential confirmation of this theory. Fischbeck, Neundeubel, and salzer4 have demonstrated that the oxidation of iron in carbon dioxide and other atmospheres at high temperature obeys a linear relationship. Because the Arrhenius temperature coefficients of the reaction rate constants changed at the A, point they concluded that the passage of iron into the oxide controlled the reaction. This viewpoint has been accepted by Benard and ~albot&apos; to explain the occurrence of linear rates in oxygen before the onset of diffusion-controlled parabolic oxidation. This basic premise of a rate-controlling reaction at the iron/oxide interface has been questioned recently by Hauffe and Pfeiffer.&apos; Since the formation of wustite may follow a linear or parabolic relationship depending on the pressure of the gaseous re-actant, they propose that linear oxidation is determined by a chemisorption reaction while parabolic oxidation is controlled by diffusion. As confirmation of this viewpoint, Hauffe and pfeiffer6 and Pfeiffer and ~aubmeyer&apos; have established that the linear scaling constants of wustite formation at 1000°C in carbon-dioxide or low-pressure oxygen atmospheres

Jan 1, 1961

By T. J. Nowak

The heat flow processes determining the injection and shut-in temperature logs in a water injection well have been analyzed and the theoretical basis for determining the water injectivity profiles from the temperature logs has been presented. Both the injection and the subsequent shut-in logs are necessary to resolve the injection interval into relative water intake strata; the former, to provide an accurate estimation of the thicknesses of the strata, and the latter to indicate the major and minor intake rates into the strata. A procedure is described for estimating the injectivity profile from the temperature logs and is applied to several temperature logs. For a water injection well, a comparison is made of the injectivity profiles obtained from the core analysis, the spinner survey, and the temperature logs. INTRODUCTION In secondary recovery of oil by water flooding, the injectivity profile is needed to obtain diagnostic evaluation of water intake distribution over the injection interval. If the distribution is unfavorable among the various strata, corrective measures can be taken to provide better control. Numerous methods have been developed for determining the injectivity profile from water velocity measurements in well bores. Often, dependence is placed upon core analyses and/or electric logs for estimating the relative water intakes over the injection interval. In many cases, the temperature log method described herein will give results more diagnostic than those obtained through use of the other available methods inasmuch as it is based upon the study of temperature disturbances in and around the well bore as a function of water flow in the well bore and in the formation. This method is the result of analyses of a number of temperature surveys made in water injection wells to determine the point of entry of the water into the formation. The material in this paper is presented in two sections: the first deals with the theoretical study of temperature survey data, and the second deals with the field application. PART I — THEORETICAL TREATMENT OF TEMPERATURE LOG DATA Before discussing the various aspects of heat flow relative to temperature log data, the phenomena that give rise to well bore temperatures — namely, the indigenous formation temperature and the associated rates of heat flow — will be considered. Geothermal Gradient The geothermal gradient is defined as the increment of depth at which the indigenous subsurface temperature increases by l°. It is caused by the continuous flow of heat outward from the interior of the earth. The flow of heat is an equilibrium process between the heat sources, the thermal conductivities of the formations, and the mean surface temperature. Therefore, there is no accumulation of heat energy in the path of heat transmission, and the geothermal gradient for a given formation will depend upon its thermal conductivity.

Jan 1, 1953

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.&apos; The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin&apos; reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,&apos; and Ahmann and Baldwin.&apos; The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"&apos;&apos; have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

By A. L. Ph. B. Holley

(Read at the Philadelphia Meeting, February, 1878.) THIS paper is an abstract and a discussion of results obtained by the United States Test Board in experiments upon 14 brands of wrought iron, most of which are well known and of high repute.* The iron was all intended for chain-cables; it was tested in the form of bars, usually of nine sizes, from 1 inch to 2 inches round, and also in the forms of single links and short chains. Not less-than 2000 tensile tests were made, each showing elastic limit, elongation, and reduction of area. This work was done with conspicuous intelligence and fidelity, at the Washington Navy Yard, by Commander L. A. Beardslee. Some important practical results and principles which he has developed, and others which he has confirmed, will be referred to. The chemical part of this work consists of 42 complete analyses (including slag), by Mr. Blair, chemist to the Board. EFFECTS OF COMPOSITION ON STRENGTH. Variations in the physical qualities of iron may he due to different composition, or to different treatment in manufacture, or to both these complex causes. In order to determine the specific causes of variation, one class of altering conditions should be made to vary largely, while the other classes should be kept uniform. Then another class should be varied, and so on, until the value of each is ascertained. As all the irons under consideration were intended to have that purity and refinement which was deemed indispensable in chain-cables, their chemical analyses are perhaps more important in proving that physical variations result chiefly from treatment, than in pointing out the specific effects of certain ingredients. While the subject of treatment-especially the increase of strength by greater reduction in rolling-may be the more important one, it can be best appreciated after we have familiarized ourselves with the gen¬eral chemical and physical characters of the irons. The typical facts are given in the following tables. * As the present object of the Board is not to compare the products of different makers, but to discover the physical effects of various composition and treatment, the irons are designated by letters rather than by their trade names.

Jan 1, 1878