Search Documents

By N. S. Stoloff, K. R. Jordan

The temperatwe and grain size dependence of the mechanical avoperties of ordered and disordered Fe-49 pct Co-2 Pct V were investigated. The yield and flow stresses obeyed the Hall-Petch relationship u = ai + kd-&apos;I2. Ohdering reduced the intercept stress cjj and raised the Petch slope, k, at all temperatures. Ordering also increased the temperatwe dependence of k. The ductile to brittle transition temperature increased with order and grair~ size. Cleavage fracture was nucleation limited and the fracture stress did not zlary linearly with d-&apos;". A quantitative test of the Cottrell-Petch fracture theory (and recent modifications which consider the influence of slip mode), demonstvated that this theory is not applicable to FeCo-V. COTTRELL&apos; and etch&apos; independently suggested that a criterion for cleavage failure at the yield point, a,, based on dislocation pileups at a grain boundary or other obstacle to dislocat.ion motion, is: aYYkd&apos;I2 1 opy [ll or, equivalently, aikz,d112 +k:)bpy [2] where a, and ky are the Hall-Petch intercept and slope, respectively, 2d is the grain diameter, P is a geometric factor dependent on the macroscopic ratio between shear and tensile stress, p is the shear modulus, and y is the true elastic surface energy. When the product of quantities on the left side of the equation is equal to or exceeds that on the right, cracks should be able to nucleate and propagate at the yield stress, as shown schematically in Fig. 1. Therefore a high intercept stress, high Petch slope, or coarse grain size favors brittleness. petch3 associated the existence of a ductile to brittle transition in ferrous alloys with the temperature dependence of ai. One of the earliest modifications of the Cottrell-Petch theory was presented by ~rmstrong,~ who derived an expression for transition temperature in terms of several measurable flow and fracture parameters. The latter paper was able to rationalize situations in which the transition temperature increases with decl-easing grain size, as in the case of molybdenum,&apos; and also suggested that Ppy should be a function of grain size as well as temperature. More recently Johnston et a1.6 and Smith and worthington7 have suggested that the temperature or composition dependence ol&apos; ky must also be taken into account if there is any cha.nge in deformation mode, as from wavy to planar slip, or wavy slip to twinning, with change in temperature or solute content. Armstrong %as suggested that for hcp metals changes in o;k,dw> o;k,d1/2< / is / ^^^^ / / y_______________________________________ d-"2 Fig. l—Schematic representation of grain size dependence of yield stress, cry, and fracture stress, CTF. Intersection defined by Cottrell-Petch equation. slip mode should be incorporated in the theory through changes in the critical resolved shear stress for the slip system which controls ky. The purpose of the present investigation was to critically test the modified677 Cottrell-Petch theory of fracture in the superlattice alloy Fe-49 pct Co-2 pct V, by studying the grain size dependence of the yield and fracture stresses over a range of temperatures, in conjunction with an investigation of slip mode and fracture behavior. Previous work has shown that long range order results in a sharp decrease in flow stress, a small increase in work hardening rate and a drastic upward shift in the ductile-brittle transition temperature of F~CO-V.~&apos;~ The only comprehensive study of slip character in this alloy has been reported in a preliminary account of the present investigation.10 EXPERIMENTAL PROCEDURE The experimental work was carried out on material produced from a 10 lb vacuum melted ingot, of composition 49.32 wt pct Co, 2.09 wt pct V, balance Fe. 30-mil thick sheet samples with a 1; in. gage section were machined from cold rolled stock. The degree of cold work ranged from 85 pct for the finest grained samples to 5 pct for the coarsest grain size. Details of ingot fabrication are reported elsewhere." Equi-axed grain sizes in the range 12.7 to 75.4 p were obtained by annealing for varying times at 850°C. (Re-crystallization annealing time, rather than temperature , was varied to control grain size to insure that samples of all grain sizes contained equivalent quenched-in vacancy and interstitial concentrations.) Grain sizes were measured by the line intercept method on several specimens of each grain size. Following recrystallization, all samples were disordered by quenching into iced brine.

Jan 1, 1970

By K. P. Chong

Introduction One of the requirements of processing oil shale or other energy bearing rocks is to optimize particle sizes and permeability distributions in fragmentations as indicated by Hommert (1984). Basic to the understanding and planning of in situ fragmentation and ex situ mining of oil shale are the mechanical properties. During the past six years, an innovative and unique program was established by Chong et al. (1979, 1980a, 1980b, 1982a, 1982b) that developed an efficient methodology for standardized and simplified mechanical testing of the western oil shale. The experiments include precise, representative, and duplicable sample preparation; uniaxial static compression testing; "modified" split cylinder testing; uniaxial creep and relaxation testing under extended periods of time; dynamic testing with varying strain rates; and 3-D constitutive relationships. However, as far as the fracture mechanics is concerned, as Edl (1980) pointed out, there is still a lack of understanding "of the fundamental explosive rock breakage mechanisms," which "has necessitated extensive reliance on very costly empirical approaches." Fracture mechanics of rocks and oil shale (Costin, 1981; Schmidt, 1977; Abou-Sayed, 1977; and Barker, 1977) has been based on conventional fracture mechanics using regular notched samples with limited variations of oil yields and assuming the material to be isotropic and elastic (Kobayashi, 1975; Caddell, 1980). A cylindrical double cantilever beam (DCB) specimen with a "V" slot, known as a short rod specimen, has been used by Barker (1977) to determine fracture toughness of rock materials. The inherent geometric stability of the reinforced DCB specimen makes it suitable to be used with all brittle materials. Due to its remarkable stability for the initial crack growth, the DCB specimen can be used for dynamic fracture toughness testing as well. This specimen is more suitable for the evaluation of fracture toughness at high strain rates than most other fracture specimens. However, Barker&apos;s DCB specimen is not very well adaptable for short cores or layered rocks since the specimen contains numerous layers (say in a 100-mm (4-in.) long specimen), and the rock properties change from layer to layer. Schmidt (1977) studied the fracture mechanics of oil shale with two oil yields, using notched beams. Using several independent established testing methods, Costin (1981) pioneered the investigation of the static

Jan 1, 1986

By John W. Langley

The papers of Mr. W. J. Keep, read before this Institute, have called attention to the influence of aluminum in cast-iron and on iron and steel castings. The information in these papers is interesting and valuable, as showing the modifications which iron undergoes when dosed with sufficient aluminum to form a distinct alloy, the quantity of the alloying metal used being such that the amount remaining in the casting is sufficient to be readily discovered by analysis. The same is also true of the so-called aluminum-steel patented by R. A. Hadfield, where the proportions specified are such as to leave in the finished steel from one-twentieth to one-tenth of one per cent. of aluminum. Whether these alloys are of practical utility or not has thus far . not been proved by any extended tests on a large scale, and until such evidence is forthcoming it may be safely held, provisionally, that such a use of aluminum is of doubtful utility. But there is another function which this metal can perform that has been known for some time, and which has passed beyond the experimental stage, viz.: its beneficial effect in securing sound ingots. It appears to be a general property of all metals when in the fluid state and at a temperature considerably above their points of fusion, to contain gas, either dissolved from the air or frorn the furnace, or else self-evolved by internal reactions. Silver, perhaps, shows this power in the highest degree, and mercury and lead in the least; midway stands steel—the quantity of gas which it can hold in solution, or " occlusion " as it has been called, varies with its temperature, its composition, and its mode of manufacture. When the steel sets in the mould, a portion of this gas escapes, causing blow-holes, surface defects, boiling-over, wildness, and quite a long train of troubles, familiar to all practical steel-makers. Ferro-silicon has long been used as a quieting agent. The first extended use of it for this purpose was made at Terre-Noire, in

Jan 1, 1892

By J. E. Hilliard

AS is well-known, the length per unit volume, Lv, of any lineal feature (such as grain edges in a polycrys-talline specimen) can be estimated from a count of the number of point intersections with a random plane of polish. Specifically:&apos; Lv = 2NA in which NA is the expected number of intersections per unit area of the plane. As with all other measurements in quantitative metallography, the estimation of Lv is subject to a sampling error, the magnitude of which will depend on the number of observations. The analysis is usually performed by counting the number of intersections falling within a closed test figure of known area applied to a succession of different areas on the plane of polish. The test figure can be drawn directly on the screen of a projection microscope or else superimposed on the image of the structure by means of a reticule in a focusing eyepiece of an ordinary microscope. The use of micrographs is very inefficient unless, as in the present study, these are also needed for some other purpose. Consider an analysis in which n applications are made of a test figure within which the expected number of intersections is N. The expected total number of intersections counted is then given by NT = nN If (N) is the standard deviation in N for one application of the figure and if the latter is applied to non-overlapping regions so that the N&apos;s are independent in the statistical sense, then the standard deviation in Nt is given by: a(NT) = a(N)vn Eliminating n from Eqs. [2] and [3] we obtain: Thus, k will be a constant for a given specimen and test figure. From Eqs. [ I] and [4] we find As is to be expected, therefore, the fractional error in the estimation of Lv is inversely proportional to the square root of the total number of intersections counted. It is very desirable to have at least a rough estimate of k before starting an analysis, since it will then be possible to decide in advance by use of Eq. [5J how many counts should be made in order to achieve the desired accuracy in Lv. Without such information the investigator, unless lucky, will either do needless (and tedious) work or else obtain a result with too large an error. It is very easy to calculate k for the limiting case of N — 0, i.e., when the test figure is vanishingly small. In this case there is a negligible probability of two or more intersections falling within the figure. There are therefore only two possible outcomes: a count of one with a probability of, say, p and a zero count with a probability of (I-p). Thus and Therefore: We might expect k to depend on N and therefore on the size of the test figure. Such a dependence was observed2 in the analogous case involving the estimation of grain-boundary area per unit volume by a count of the number of intersections of a test circle with traces of the boundaries on the plane of polish. In this case the theoretical value of k at the limit N — 0 was 1.41. It was also predicted that k would display an initial sharp decrease with increasing N. Experimentally, k was observed to decrease to a value of 0.62 at N - 6 and thereafter remain approximately constant. Furthermore, the value of k for N > 6 was found to be insensitive to the form of the structure provided no pronounced anisotropy or grain-size variation was present. In order to determinewhether k would exhibit a similar dependence on N in the estimation of grain-

Jan 1, 1967

By C. E. Johnston

In December 1956, International Minerals & Chemical Corp. installed a rope-suspended belt haulage system in its Carlsbad, N. M., potash mine to complement the already existing rail transport arrangement. In this article the author describes when and where each system is used, the advantages and disadvantages of both, and future planning and proposed changes in haulage at IMC. The haulage system at the International Minerals & Chemical Corporation (IMC) potash mine near Carlsbad, N. M., reached a turning point in December 1956 with the introduction of rope-suspended belt haulage. In fact, IMC pioneered the use of this type of belt in the potash industry. Since that time belt conveyance has been employed as an extension of the rail system but not as a replacement of the main rail haulage. IMC&apos;s potash mine is located in the Permian Basin, approximately 20 miles east of Carlsbad in Eddy County, N. M. The 800, 850 and 900-ft levels have been exploited. From these levels over 60 million tons have been extracted. The two ore minerals are sylvite (KCl) and langbeinite (K2SO4. 2MgSO4). The principal gangue mineral is halite, with minor amounts of polyhalite, kainite and leonite. Langbeinite is mined on the 850-ft level and sylvite on the 900. The 800-ft level, with both langbeinite and sylvite mineralization, is idle. Mining heights vary from 54 in. to over 10 ft. A room and pillar mining system is used. Geologically, mining is done in the Salado salt formation. The U.S. Geological Survey has classified the 900-ft sylvite level as the first ore zone and the 850-ft langbeinite level as the fourth ore zone. Since the grade of sylvite is low, mineralization at the IMC mine is somewhat irregular and salt horses, are common. Selective mining and a flexible haulage

Jan 1, 1963

By G. W. Thomas

A simplified mathematical model of underground conduction heating in a system of limited permeability is presented. The model applies to underground retorting of oil shale, or to reservoirs containing extremely heavy oils. We assume that heat is introduced at a constant rate into a horizontal fracture which communicates between wells. The radial temperature distribution along the fractured surface is approximated by a step-function. Heat transfer away from the fracture is assumed to be by vertical conduction, and all convection effects are neglected. The model also takes into account the possible temperature dependence of thermal conductivity. A general expression for calculating the growth of the step-function temperature distribution with time is derived. The use of this expression and solutions to the one-dimensional heat equation make it possible to construct isotherms. Expressions for calculating .oil recovery, well spacing and heat efficiency are also given. An example calculation is presented for the conduction heating process in oil shale. Finally, the effect of the heat transfer coefficient between the gas and the fracture boundaries is investigated. INTRODUCTION Thermal recovery processes of oil recovery fall into the four general areas of hot fluid injection, forward combustion, reverse combustion and conduction heating. The first three of* these processes have been rather extensively studied in the past decade from both the experimental and theoretical points of view. As a result, it is possible to make reasonable engineering predictions and analyses of these processes. Little attention has been devoted, however, to the conduction heating process other than to note its possible utility.I To a certain extent, conduction heating cannot be divorced from the other regimes cited above, insofar as these provide the source of heat energy. In the conduction heating process, heat is introduced (either by combustion in the forward or reverse mode or by hot fluid injection) into a small fraction of the total reservoir thickness. This fraction may be either a streak of high permeability or an interwell fracture. Heat penetrates by conduction into the adjacent, less permeable regions of the oil-bearing rock, where the direction of conduction is essentially perpendicular to the streak or fracture. The heated product then drains by gravity or is gas driven to production wells. Conduction heating is probably most applicable to systems containing immobile bitumens such as tar sands and oil shale deposits and perhaps to low-permeability reservoirs containing highly viscous crudes. The mechanism also acts in combination with other thermal processes where fingering or overriding of a bed occurs. It seems probable that in at least one field test, conduction heating of this type was very influential.2 In this presentation we give a first approximation to some of the quantitative aspects of conduction heating. Marx and Langenheim3 treated a similar problem where they focused attention upon the injection interval, which spanned the total reservoir thickness. In their model, conduction heat losses to the bounding media imposed a practical limit on the calculated heated area. In the present study, however, we shall confine the injection interval to a small fraction of the reservoir thickness and assume it has no heat capacity. We therefore direct our attention to regions outside the injection interval into which the conduction of heat is beneficial. In particular, we will endeavor to locate specific isotherms in the media bounding the injection interval. Furthermore, we will construct our model to allow the thermal conductivity to vary arbitrarily with temperature. Thus the model will be applicable to underground retorting of shale where variations in thermal conductivity may be important. THEORY We consider the rock matrix to have no or, at best, a very limited permeability; consequently a

Jan 1, 1965

By J. D. Meakin, H. G. F. Wilsdorf

An etching technique.has been used to investigate the dislocation structure of deformed @-brass single crystals. Isolated single ended pileups have been observed, and it is shown that, in certain cases, the configurations of such pileups agree with theoretical predictions. Many discrete pileups within heavily deformed regions have also been detected and the influence of surrounding dislocations on these groups are reported and discussed. Divergences between the experimental and theoretical spacings in the isolated pileups and the origin of the stress maintaining the pileups are discussed. THE spatial configuration of a linear array of identical dislocations has been evaluated theoretically by Eshelby, Frank, and Nabarro.&apos; Of particular interest is the equilibrium spacing of a series of dislocations under a uniform shear sti-ess when the leading dislocation is held fixed in the lattice; such an array is termed a single ended pileup. Eshelby, Frank, and Nabarro&apos; found that an explicit analytical solution to the problem of n dislocations in a pileup is not possible, but they were able to derive approximate formulae applicable under various limiting conditions. An alternative method of determining the equilibrium configuration was proposed by Leibfried and Leibfried and Haasen in which the discrete dislocations are replaced by a continuous dislocation density. This technique was used by Head and Louat to solve in first approximation, a number of problems of particular interest, eg., single and double ended pileups. Head has also solved numerically a number of specific configurations involving up to six dislocations. Recently Kuhlmann-Wilsdorf has obtained numerical solutions for single-ended pileups containing between three and seventy dislocations, thus making possible a comparison between appropriate experimental results and accurate theoretical values. The considerable use of the pileup concept in theories of plastic flow has stimulated a number of attempts to observe such arrays experimentally. There is of course considerable intrinsic value in revealing an isolated pileup because a direct check on the elastic theory of dislocations then becomes possible. The only technique generally applicable for studying pileups in bulk metal specimens is selective etching of the point of emergence of individual dislocations. Confining our attention to etching studies which have revealed pileups, the earliest reported work

Jan 1, 1961

By William P. Mason

FoR reasons unnecessary to enter into here, I was called upon to contradict the statement that " closed metallic vessels, partly filled with water and heated, do not become shattered by violent explosion, but simply rupture by over-pressure;" and the following experimental results were obtained in support of my position : A piece of drawn brass tubing (telescope-tubing) 1 1/2 inches in diameter and 15 inches long was closed at both ends by screwing on heavy caps of bronze. Before closing the second end the vessel was half filled with river water, the cap was then screwed on, and the closed vessel was supported upon two iron anvils, and heated in the interval between the supports by a large Bunsen lamp. The resulting explosion (which was doe to over-pressure only and not to any more occult cause) was exceedingly violent. No small damage was done to the room in which the experiment was undertaken; and the noise was like that of a cannon. Those of the pieces which could be recovered are shown in Fig. 1. Upon examining the wreck, it was noticed that one of the heavy bronze end-caps had preserved its circular section and still contained that portion of the barrel of the tube which had been screwed into it, while the other end-cap contained no portion of the tube, and was moreover sprung into a shape more or less elliptical, as if from excessive lateral strain. It was also observed that the large pieces of the shattered boiler predominated towards the end which had been closed by the un-sprung end-cap. The reasonable explanation, in view of the facts, was, that over-pressure had caused the boiler to yield through the screw-threads at A B, Fig. 2, and the righthand end-cap had blown off, thus leaving the boiler half filled with water, greatly super-heated for the new (atmospheric) pressure to which it was suddenly reduced; that this water had consequently sprung instantly into steam with dynamite effect, shattering the tube and springing the remaining end-cap. The large pieces would be expected at the open end of the boiler, as at that point the "tamping "would have been that of the atmosphere only. This explanation assumes a rupture to have been caused by gradually increased pres-

Jan 1, 1893

By H. E. Ellis, O. L. Patterson, Granville Dutton

A large-scale water-injection program for the Holt Bryant reservoir of the Delhi field has been established by means of the new automatic multi-pool analyzer. The objectives of this program were to increase reservoir pressure and eliminate a cross-dip gradient of 200 psi. Pressure increases during the first 15 months of operation have allowed for increased oil production rates of 2,600 BID or 25 per cent. To determine the required water injection it was necessary to predict natural water influx ram. Elimination of the pressure gradients required the water-injection program to account for the fluid migration and pressure interaction between segments of the reservoir. An integral part of the ana1ysis included the determination of in-place volumes of oil and gas. The operation of the automatic multi-pool analyzer in determining the water-injection program is described. New features of the analyzer inc1ude an automatic maferial balance analog and a leart-squares computer for determination of unknown reservoir properties. Operational procedures are sufficiently simple to allow direct use by reservoir engineers on a routine basis. The rapidity and accuracy with which problems may be solved permit repeated ana1yses as a check upon reservoir performance. INTRODUCTION This paper describes the use of a new analog com- puter in determining the optimum injection program for a complex reservoir. The Holt-Bryant (Fig. 1) is the major reservoir in the Delhi field of Louisiana. Production is from the Tuscaloosa at subsea depths of 2,970 to 3,286 ft. The sand dips to the south and southwest from three to five degrees. The reservoir is approximately 12 miles long and varies in width from 1/2 to 2 miles. Various calculations have placed the initial volume of oil in-place in the wide range of 275 to 355 million STB. Two small gas caps were initially present in the reservoir. The Holt-Bryant reservoir was discovered in Dec.. 1944, and was fully developed with 188 producing wells by 1948. After development was completed, an east-west pressure gradient began to establish itself. This

Jan 1, 1957

By T. D. Mueller

Many investigators have used the response of the "dimensionless aquifer" to a unit pressure drop or a unit fluid-withdrawal volume to calculate the performance of an aquifer in supplying water influx to an oil reservoir. In the past, these response functions have been calculated with the aid of the Laplace transform. With the advent of ultra highspeed digital computers, it becomes practical to solve for the response functions with finite-difference techniques. The computer method also permits extension of the dimensionless-aquifer concept to include the nonhomogeneous aquifer wherein the permeability and other properties vary as a function of the space co-ordinates. This paper gives results of calculating the response functions for a series of nonhomogeneous aquifers. Response functions are presented for both linear and radial aquifers whose thickness, permeability-viscosity ratio and porosity-compressibility vary. These functions are new and should prove useful to the petroleum engineer in analyzing the behavior of nonbomogeneous aquifers. Results are presented in the form of charts that can be easily used by the field engineer. INTRODUCTION Aquifers which surround many oil and gas reservoirs have the ability to supply water influx to such reservoirs as oil and gas are withdrawn. This water influx, called natural water drive, provides one of the most effective driving mechanisms for the production of oil and gas. In producing a reservoir, therefore, it behooves one to make the maximum use of natural water drive. To achieve the maximum use, the reservoir engineer must be able to predict the performance of an aquifer under a variety of production schemes that may be proposed for the reservoir. Unfortunately, the physical properties which dictate aquifer behavior often are known only within limits. Seldom do wells penetrate the porous strata of the aquifer. Even when they do, quantitative information regarding porosity, permeability and water compressibility is seldom available. It is known, however, that the water efflux from most aquifer systems is governed by a single, relatively simple, linear, partial differential equation. Also, the general physical location of the aquifer boundaries often are known. A technique originall proposed by Hurst1 and van Everdingen and Hurst2 has been found useful in analyzing reservoirs in this situation. The idea was later expanded by van Everdingen, Timmerman and McMahan3 to include the mathematical technique of least-squares fitting. This latter method will be referred to as the VTM method. The basic assumptions of the VTM method include the following. 1. The location of the physical boundaries of the aquifer are known. 2. The flow conditions at these physical bound-daries are also known. 3. The aquifer is homogeneous; e.g., thickness, permeability, water compressibility and porosity are constant throughout. In the VTM method, a material balance is made on the fluids entering and leaving the reservoir. In the balance equations, the water-influx term is represented as the product of the water influx from an arbitrarily-selected, dimensionless aquifer system times an unknown conversion number. This balance can be formed as many times as there are data points in the history of the reservoir. Each time, the conversion number can be evaluated. If the reservoir engineer has picked the correct dimensionless aquifer to represent the real aquifer, the conversion number remains constant for all balances that have been made over the history period. If such a situation occurs, the reservoir engineer can then predict the performance of the reservoir for any type of production scheme by using the function associated with that particular dimensionless system and the derived conversion number. These functions will be referred to as the response function of the aquifer. If the aquifer is nonhomogeneous (e.g., if the porosity, permeability, thickness, porosity, or

By Luther Lennox

DURING the last few years, one of the great problems in the milling of all ores has been that of crushing. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of crushing to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of crushing methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative crushing resistances of a number of ores now being milled in this country and Alaska, the management of the Portland mills requested samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh . screen; in the screen analyses tabulated and plotted herewith, the 150 mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves.

Jan 8, 1918

By C. E. Reinhard

A useful accelerated weathering test should be capable of placing any series of metals quantitatively in the same order of endurance as that noted under a particular set of actual exposure conditions. The development of such a test must necessarily depend to a considerable extent upon data obtained from a wide variety of exposures. This paper offers preliminary data from exposure tests on nine metals placed in 11 locations in the Lehigh Valley, within a radius of 20 miles from Palmerton. The exposure conditions vary from a severe industrial atmosphere to a pure rural atmosphere. The data are offered as evidence of the necessity for the identification and evaluation of the variables of corrosion and as illustration of some of the variations to be considered in the development of a useful accelerated test. It is quite clear, from this evidence, that a useful accelerated test must be versatile to the extent of showing the probable variations of corrosion resulting from differences in atmosphere as well as from differences in the metals. The paper is presented solely with the object of pointing out the wide variations in relative merits of several common metals in resisting corrosion and without any thought of initiating controversy regarding the merits of particular metals. For this reason the metals are designated only by symbols in the tables and no key is given to these symbols. Test Procedure Specimens, 4 by 6 in., were cut to accurate dimensions from each of the following metals or alloys: aluminum, ascoloy, copper, copper steel, galvanized iron, and zinc. Additional grades of these metals bring the total to nine types. Since it was impossible to obtain the required number of copper-steel specimens having equal surface conditions of rust and scale, it was thought advisable to pickle these specimens in a hot solution of 10 per cent. sulfuric acid. All other specimens were carefully cleaned in ether and alcohol and weighed just prior to exposure. Four specimens of each type of metal were mounted on a test rack by means of porcelain insulators. The racks were so constructed that

Jan 1, 1929

By C. E. Reinhard

A useful accelerated weathering test should be capable of placing any series of metals quantitatively in the same order of endurance as that noted under a particular set of actual exposure conditions. The development of such a test must necessarily depend to a considerable extent upon data obtained from a wide variety of exposures. This paper offers preliminary data from exposure tests on nine metals placed in 11 locations in the Lehigh Valley, within a radius of 20 miles from Palmerton. The exposure conditions vary from a severe industrial atmosphere to a pure rural atmosphere. The data are offered as evidence of the necessity for the identification and evaluation of the variables of corrosion and as illustration of some of the variations to be considered in the development of a useful accelerated test. It is quite clear, from this evidence, that a useful accelerated test must be versatile to the extent of showing the probable variations of corrosion resulting from differences in atmosphere as well as from differences in the metals. The paper is presented solely with the object of pointing out the wide variations in relative merits of several common metals in resisting corrosion and without any thought of initiating controversy regarding the merits of particular metals. For this reason the metals are designated only by symbols in the tables and no key is given to these symbols. Test Procedure Specimens, 4 by 6 in., were cut to accurate dimensions from each of the following metals or alloys: aluminum, ascoloy, copper, copper steel, galvanized iron, and zinc. Additional grades of these metals bring the total to nine types. Since it was impossible to obtain the required number of copper-steel specimens having equal surface conditions of rust and scale, it was thought advisable to pickle these specimens in a hot solution of 10 per cent. sulfuric acid. All other specimens were carefully cleaned in ether and alcohol and weighed just prior to exposure. Four specimens of each type of metal were mounted on a test rack by means of porcelain insulators. The racks were so constructed that

Jan 1, 1929

By Clyde E. Williams

Estimates indicate a life of known Lake Superior iron ore reserves of 20 to 30 years. Although some believe the future ore supply will come from foreign sources and will be brought to interior points via the projected Great Lakes-St. Lawrence waterway, and others fear a displacement of the interior steel-producing districts to the Atlantic seaboard, the author has faith that American engineering skill will make possible the use of lean ores from the Lake Superior district. Three general types of Lake Superior ores and ore formations, that represent possible reserves and require beneficiation, are: (1) the wash ores of the western Mesabi range, (2) the partly leached hematitic formations, and (3) the oxidized but largely unleached iron formations. The total tonnage represented by (1) and (2) is not large, but the recovery of iron from present washery tailings would bring on the market the equivalent of nearly one million tons of wash ore, annually. Group 3 comprises the magnetic iron formation of the eastern Mesabi range, the hematitic formations including the taconites of the Mesabi range, and the iron formations of all the other ranges. These formations represent our future supply of iron ore. Their treatment requires intensive research because the bulk of the iron oxide and silica minerals exist in a finely disseminated condition. The possibilities of the adaptation of tables, oil flotation, and other processes warrant extensive study. Cheaper method of agglomeration of the concentrate is essential. Recent developments in better preparation and sizing of blast-furnace charges indicate that substitution of agglomerated ore for fines will increase furnace efficiency and output. If agglomerated beneficiated ore can be shown to rate a per-unit premium for iron contents over the base rate or a premium for structure, the payment of these would greatly assist in enlarging our iron ore supply. Since present methods of taxation of ore reserves, which encourage the rapid depletion of rich ores, will result in using up our rich ores and later on putting domestic producers at a disadvantage in competing with&apos; foreign producers, it would seem highly provident to conserve our rich ores and to increase the use of beneficiated ores as soon as possible.

Jan 1, 1931

By Thomas L. Garwood, F. C. Menk

IT is generally accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sues contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in I both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uniform bed. With a dusty feed the fines tend to segregate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants dedusting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets. DEDUSTING The practice of dedusting, sometimes called aspirating, has presented a problem in disposing of the dust and intermediate small sizes recovered in the process. It has been found that no difficulty is experienced in disposing of the intermediate sizes, since they are free of fine dust and burn freely on grates built for small coal. They handle well, flowing freely from bins and hoppers and into conveyors, and pulverize easily. They have a low angle of repose. In tests made on this size as a feed to coke ovens, the results have been excellent, in that the natural breakdown of coal in handling and shooting in the mine gives this small-size coal good coking characteristics-producing a strong, fingery coke structure. Deduster dust from Illinois coal has been

Jan 1, 1950

By F. M. Stewart, F. H. Callaway, R. E. Gladfelter

In this paper oil initially in place is calculated by the various methods commonly used for analysis of water drive fields using data available as time progresses. Rate and pressure are predicted by means of the same methods using data available at the end of two years&apos; history. These predictions are then compared with subsequent performance permitting an evaluation of the methods, which are Modified Schilthuis, Simplified Hurst, van Everdingen et al (1952), and the Electric Analyzer. INTRODUCTION Several variations of the material balance equation, differing in the term used to evaluate water influx, are in common use for estimating oil in place, predicting rate and volume of water influx, and forecasting producing rates and reservoir pressure in water drive reservoirs. The electric analyzer with an electrical network set up to simulate the oil reservoir and aquifer and their contained fluids may be used for the same purpose. Examples of the application of one or another of these methods have appeared in the literature. The accuracy and reliability of the material balance for calculating oil in place have been covered.&apos; However, there have been few articles in which more than one method has been applied to an actual field allowing a comparison. It is felt that a field example, simple in nature, where the Modified Schilthuis, Simplified Hurst, van Everdingen et al (1952), and the Electric Analyzer have been applied would be of benefit in providing an evaluation of these methods as to their comparative usefulness and reliability in calculating initial oil in place and predicting performance. The Torchlight Tensleep reservoir is a small field in a large aquifer. The reservoir oil is greatly under-saturated, having a bubble point of only 55 psi and 2 cu ft/bbl of gas in solution. Changes in the reservoir volume factor in the range of pressures encountered are small, meaning little error in converting production to reservoir conditions. The pressure has declined from 1,618 psi initially to 137 psi during the first four and one-half years. Water production has been negligible. For Torchlight, the material balance equation as discussed later is considerably simplified by the omission of terms having to do with free gas. Thus with simpler equations, less variables to consider, the large pressure drop, the absence of a gas phase, and rapid pressure-rate adjustments, which mean an unusual amount of history in a short time, the reservoir appears suitable for comparing the methods listed above. GENERAL INFORMATION ON THE FIELD The Torchlight field is located on the eastern side of the Big Horn Basin, Big Horn County, Wyo., approximately 3 miles east of the town of Basin. The Tensleep reservoir was discovered in September, 1947. It lies at a depth of about 3,000 ft and produces oil of 35" API gravity. A total of five wells have been completed in the Tensleep, but only four are now producing. The reservoir is well defined in areal extent in that a total of 13 wells have penetrated the Ten-

Jan 1, 1955

By R. W. Heckel, H. W. Paxton

The growth of grain boundary films and Widmanstiitten plates of proeutectoid cementite in hypereutectoid steels ulas considered quantitatively in three plain carbon steels and one "pure" iron-carbon alloy. Growth was found to take place at a slower rate than would be predicted on the basis of a model invoking rate control by long range diffusion of carbon. The films in the pure alloy grew faster than those in the plain carbon steels. A possible explanation is suggested. In 1904, Nernsst&apos; and Brunner2 postulated that ionic crystals growing in supersaturated aqueous solutions grew at rates determined by diffusion through the solution to the growing crystal interface. The gradient down which the diffusion took place was assumed to be fixed by the supersaturated bulk solution concentration, the concentration dt the crystal surface and some arbitrary distance. The flux of material to the crystal was described as Flux where D is the diffusion coefficient, A the crystal surface area, Ci the bulk solution concentration, Co the saturated solution concentration, and 6 the thickness of the diffusion zone. It is obvious that the expression is an adaptation of F+ick&apos;s3 first law of diffusion (steady state). This was the initial formulation of what will be defined here as "diffusion controlled growth," i.e., growth limited by the long range diffusion of a component either to or from the advancing interface assuming both phases at the interface to be in equilibrium. This idea of equilibrium interface concentration implies an infinite reaction rate at the interface. Volmer, Zener,&apos; and 11schner6 have derived expressions for the diffusion controlled growth of spherical precipitates in metallic systems. These analyses agree that the growth in a given direction should be parabolic with time. Brown and Hawkes7 observed that graphite, formed both from the decomposition of cementite and from the decomposition of eutectoid austenite in cast irons, grew according to a parabolic relationship and, therefore, concluded that the laws of diffusion controlled growth, as defined above, were obeyed. They, among others, failed to consider, however, that parabolic growth is a necessary, but not sufficient, condition for diffusion controlled growth. Mehl and Dube"&apos; have pointed out that equilibrium may not be realized because the concentration at the interface cannot change instantaneously from that of the bulk to the saturation value. Furthermore, they propose that an equilibrium solute concentration in the parent phase adjacent to the precipitate would remove the thermodynamic activity gradient across the interface and, thus, stop the growth process. Frisch" has also emphasized the importance of interface concentrations that vary throughout the growth of a new phase. The variation in activity across an interface, as discussed by Onol&apos; and Cahn and Hilliard,12 is of fundamental importance to this question. Ham13 considered the data of Turnbull14 on the growth of barium sulfate in aqueous solutions. He concluded that the data could be analyzed in terms of a radiation-type boundary condition. Flux across interface = K (c, - C,) [21 where C, is the concentration in the solution at the interface, Co the saturated solution concentration, and K the proportionality constant. The edgewise growth of Widmanstlitten plates, frequently referred to as the rate of lengthening, was first considered by Zener.&apos;&apos; Basing a mathematical analysis on steady-state (constant velocity) growth he concluded that where G is the growth rate, D the solute diffusivity, Ci the concentration in the bulk, Co the equilibrium interface concentration, C, the concentration in the precipitate, a a constant, Y the radius of curvature of the edge of the plate, and rC the critical radius, i.e., the radius which would increase the activity of solute at the interface at equilibrium under the influence of capillarity to that of the bulk. Zener1&apos;

Jan 1, 1961

By Wilford L. Stork

Certain influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,l such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, &apos;thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is redly burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the . world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book.3 The work of J. E. Johnson, Jr., has revolutionized the metallurgy of cast iron and it seems apparent that all future work must include an oxygen determination just as we include silicon, sul-

Jan 1, 1920

By P. S. Rudman

Laves phases, AB2, are considered as Izerrzisub-stitutional solutions m1hich are defined by a one-for-truo replacement scheme. Atomic-size tnisfit is considered in terms of deviations of the ratio 2V°b/V°A from unity, where v° = atomic volume. A simple elastic model has been used to calculated deviations from "Vegard&apos;s law of atomic vol-umes". Comparison has been made between calculated and observed atomic-volume deviations fov 222 Laves phases. Agreement is generally very good although there ave some few exceptions which appear to be excusable in terms of electronic changes that ore beyond the scope of the present model. We can consider the formation of a binary sub-stitutional solution A-B from an A solvent as one-for-one replacements of A atoms by B atoms. As the atomic-size ratio deviates from unity, the solution becomes thermodynamically less stable and hence more restricted because of atomic-misfit strain energy. In accordance with our previously presented conclusion1 that the atomic volume, v, is in general the most appropriate measure of atomic size, the ideal size ratio for a binary sub-stitutional solution is vg/vA = 1. The Laves phases have been described by Berry and Raynor2 in terms of various stacking sequences of hexagonal layers of B atoms for the three structures MgZn2(C14), MgCu2(C15), and MgNi2(C36). To form the Laves phase of ideal composition AB, we start with complete hexagonal layers of B atoms in the appropriate stacking sequence and we remove, according to an appropriate scheme for each structure, two out of every four B atoms and replace the two removed atoms by one A atom. We thus might expect to find that the ideal size ratio for the Laves phases is 2v/B/ VA= 1. From this point of view, then, we call Laves phases hemi-substitutional solutions since we employ one-for-two replacements. By analogy with substitutional solutions we can expect for Laves phases that as the ratio 2VB/Va deviates from unity the phase occurrence will be more restricted. Laves3 has plotted the distribution of Laves phases as a function of the radius ratio, ?A/rB, and found that, while the distribution extended from 1.05 < rA/B < 1.50, the

Jan 1, 1965

By T. L. Joseph

Sulfur balances calculated from operating data covering thirty-five blast furnaces indicate that approximately 92 per cent. of the total sulfur charged enters with the coke, 7 per cent. with the ore, and 1 per cent. with the stone.. Most of the sulfur is carried from the furnace by means of the slag, the total amount eliminated being the product of the slag volume and the percentage of sulfur it contains. Additional sulfur in the charge must be eliminated either by increasing the percentage of sulfur in the slag or the quantity of slag. From relations found between slag volume and coke consumption and sulfur in the coke and slag volume, curves have been prepared showing the relative value of blast-furnace coke as its sulfur varies from 1 per cent. CHARCOAL was the predominant blast-furnace fuel until 1838, when it was found, by the operation of a 2-ton experimental furnace, that anthracite could also be used. This information was a stimulus to the iron industry, particularly in eastern Pennsylvania where anthracite was available at low cost. The production of anthracite pig iron increased steadily and, in 1855, its tonnage exceeded that of charcoal iron. Of the 680 furnaces in operation in 1874, the 226 using anthracite produced nearly one-half the total tonnage. In 1869, the production of coke furnaces exceeded that of charcoal furnaces and, in 1875, coke surpassed anthracite as a metallurgical fuel. In 1907, the output of anthracite pig dropped well below a million tons and its present significance is largely historical. In recent years, the production of coke has gone hand in hand with the production of pig iron and it has gradually attained the position it now occupies as a universal blast-furnace fuel. Charcoal, however, has great merit as a blast-furnace fuel chiefly because of its freedom from ash and sulfur. The harmful effect of the latter and the necessity of keeping the percentage of this element in pig iron at a minimum are well recognized. Other contaminating elements can be reduced to specified limits in the steelmaking process, but the control of sulfur belongs essentially to the blast furnace. The purpose of this paper is to point out the distribution of this impurity in blast-furnace

Jan 9, 1924