Search Documents

By O. N. Wampler

UNDERGROUND lighting in the zinc mines of the Tri-State district can be separated into four di-visions. 1. Foot of shaft. 2. Pumps, fans. incline hoists and other stationary machinery. 3. Haulage ways. 4. Headings and stopes. One of the main improvements in lighting around the bottom of the shaft is in the use of skidoo flash lights, which have replaced the old electric skidoo bells. These bells were used as signals from the hoisterman to the tub hooker. In the event that a can bumped the side of shaft or a rock spilled from the can when dumping; the hoisterman rang the skidoo bells as a signal for all to leave the vicinity of the shaft bottom on a dead run. These bells were much better than no signal at all, but many of them were often out of order; the worst feature being that when out of order this fact was not immediately indicated. The electric flash-light signals work on the opposite principle and are burning at all times except when the hoisterman breaks the circuit when signaling danger. Therefore should a break or short occur in this arrangement, the shaft bottom is immediately thrown in darkness. Since the reaction from the eye is quicker than from ear, there is a slight saving of time- to the men escaping from the point of danger. Even this brief period of time may save a life. One other, point, to be emphasized, is that all lights near the shaft bottom should be on the signal circuit so that the entire area is momentarily darkened. I. have inspected mines where only one or two lights are used as signals, with the remaining lights around the shaft on another fixed circuit. In this case the flashing of the signal lights is almost drowned out by the stationary lights. These flash signals must be as startling as possible, which can only be done by flash-ing all the lights.

Jan 6, 1928

By Joseph E. Pogue

Price is a complicated concept, for price is both a cause and an effect. This reciprocal aspect is commonly overlooked and the oversight is the source of many economic maladjustments. Price is the resultant of the ratio between supply and demand, but it differs from a mathematical concept of a proportion, by itself constituting an economic force which continuously alters the elements that determine the relationship. Price, therefore, is not merely the outcome of other forces but is in its own right one of the most powerful of economic agents. Price accordingly does not play a passive role; nor can it be sterilized or rendered inactive. In consequence, price cannot be fixed or at least kept fixed, except by the elimination of all freedom of choice on the part of producers and consumers. A primary objective of all economic activity is equilibrium. The same is true of a unit of economic activity, the single industry. The plane upon which equilibrium centers may shift in the course of time, but equilibrium itself is the point of departure and the point of return. If an industry is in equilibrium, that industry is operating effectively. The motivating forces of an industry—profits or the common good—are not to be confused with the prerequisite of equilibrium, but this mistake is often made. The producer is dominated by the profit motive; the consumer, or his collective representative, by the general welfare motive. No one is the advocate for equilibrium; that status is supposed to be arrived at automatically. If the forces of competition are perfectly free, such is the tendency. Equilibrium For the purposes of this analysis, equilibrium needs to be broadly defined and is conceived to involve: (1) balance between supply and demand; (2) internal equipoise amongst the elements within an industry; and (3) symmetry in respect to the whole economy. This definition implies flexibility and case of adjustment; a ready accommodation to change. Equilibrium does not postulate profits or nonprofits, social objectives or the lack of them. A decadent industry may be in equilib-

Jan 1, 1937

By George W. Maynard

For an account of the discovery and the determination of chromite on Port au Port Bay I am indebted to Mr. Obalski, Government mining engineer for the Province of Quebec. He writes: " In June, 1894, with the authorization of our Government, I went to Newfoundland to examine some asbestos property. Passing through Halifax, I had interviews with some gentlemen who told me that besides the asbestos there was in the same district a big deposit of iron-ore. They handed me some specimens, and, after ascertaining that they were not magnetic, and learning that they were found in serpentine, I said they were chromic iron. I visited the place on June 27, 1894, and confirmed my opinion, pointing out at the same time the importance of the deposit, as appears in my report of July 9, 1894. I do not claim any credit for the discovery of chrome-ore in Newfoundland; but, as a matter of fact. when I came in contact with the Halifax gentlemen they did not appear to know the nature or the value of the mineral until I mentioned to them that it was chromite. "' Mr. Obalski's report was mainly devoted to the asbestos-deposits. That portion relating to the chromite was as follows: " On the right side of the creek there is a show of chromic iron of good quality, which appears scattered through the serpentine in several places on the face of the cliff for 40 to 50 feet. A few boulders are found farther up at a distance of 100 feet, and also in the ckeek itself. From this point the deposit exists on a relatively large area, the widest exposures being from 6 to 7 feet. Chromic iron deposits in serpentine rock have no regularity, and are merely pockets. In the case of the property in question this rule is not changed, but the pockets look to be of large extent, and could be easily worked." My own preliminary investigation of the property was made

Jan 1, 1898

By I. N. Zavarine

THE present paper is a continuation of the work on the relationship between the magnetic and the phase transformations in carbon steels during quenching. An account was given by the author in a previous paper1 of an investigation of this relationship during a continuous quench. The experimental difficulties then encountered prevented a conclusive proof of the existence or absence of such a relationship. The conclusions of the previous paper were derived indirectly. The present paper deals with the same problem, but the method of attack is modified. The technique developed by Davenport and Bain2 in their well-known study of austenite transformation at subcritical temperature was adopted in the present investigation.. They have shown that the austenite to martensite transformation can be caused to proceed at a relatively slow rate by quenching steels into a hot metal bath. Slowing down of the rate of transformation, together with an observation by Lewis3 that a eutectoid steel can be preserved in the nonmagnetic state by such quenching, pointed out a possibility of a study of both transformations .under more favorable conditions than previously described. The preliminary steps were connected with the technique of the hot bath quench. To study this phase of the present work a modification of the apparatus previously described1 was used. The modification consisted in the use of a hot quenching bath instead of brine, and in fixing the secondary and the primary coils of the apparatus in a stationary position in and around the bath. Tubular specimens, as in the previous investigation, were heated in a suitable furnace to a temperature in the austenitic

Jan 1, 1935

By Augustus Locke, Edward H. Perry

In the exploration of a copper deposit by drilling, obvious advantages are to be gained from a distinction between primary and secondary ore.' Perhaps the chief of these is the aid which such a distinction renders in determining where a given hole should stop. The copper assay, often a sufficient guide, cannot always be exclusively relied upon. Primary ores may extend downward indefinitely and may fluctuate in value independently of depth: if primary ores are consistently lean for a considerable vertical distance, there is little reason to expect that, still deeper, they will increase to the commercial grade; on the other hand, rich primary ores may persist uninterruptedly downward or may come in again below a lean interval. Secondary ores, however, have a comparatively limited vertical extent; in a large way enrichment decreases with depth and finally gives out. It follows then, that when a hole descends from profitable ore into ore of less than the commercial minimum, the practical significance of the situation depends upon whether this decrease results from a decrease in secondary enrichment or is a variation in primary content: if the copper of the ore passed through has been chiefly secondary, little is gained in the average case by extending the hole much below the point at which the commercial limit is reached; but, when copper is chiefly primary, due weight must be given to the possibility that, still deeper, the ore may again improve. The distinction between primary and secondary ore may of course be effected through an examination of the drillings. It has been found, however, to be facilitated by curves made by plotting assays against

Jan 1, 1916

By A. E. Nehrenberg

IN an earlier publication' it was shown that the.. shape assumed by a volume of growing austenite is inherited from the prior structure. The matrix grains of pearlitic microstructures are equiaxed, and austenite grows in an equiaxed manner in these prior structures. Martensite and bainite, on the other hand, have an acicular grain structure, and the austenite produced in such structures grows in an acicular manner. In the discussion of this paper' it was pointed out that in cold-rolled tempered martensite, austenite grows in an equiaxed, rather than an acicular manner. The results of an experiment carried out to arrive at an understanding of this behavior are illustrated by the micrographs. Fig. 1 shows the acicular microstructure produced by heating tempered martensite to a temperature within the Ac1-Ac3 range, 1350°F. When tempered martensite is cold rolled, then heated to the same temperature, the equiaxed structure shown in Fig. 2 is produced. A sample of cold-rolled tempered martensite heated at 1350°F just long enough for the formation of a small amount of austenite is shown by Fig. 3 to have an equiaxed (recrystallized) ferrite grain structure. The small particles of. austenite which formed at 1350°F in the equiaxed ferrite matrix are likewise equiaxed. Thus, the equiaxed growth of austenite in cold-worked tempered martensite is not a contradiction of the principles described in the previous paper, for the growth pattern reflects the matrix grain structure existing at the time of austenite formation. References A. E. Nehrenberg: The Growth of Austenite as Related to Prior structure. Trans. AIME (1950) 188, pp. 162-174; Journal of Metals (January 1950). 2 J. R. Vilella and R. A. Grange: Discussion of ref. 1. Trans. AIME (1950) 188, pp. 1378-1381; Journal of Metals (November 1950).

Jan 1, 1953

By Henry Hanson

A STUDY of the ore to be treated should be the first step in deciding on a machine for crushing or grinding. Coarse crushing is practically confined to the jaw and the gyratory crushers, the large-size jaw type being often employed in large installations as a primary crusher, followed by the gyratory type for secondary reduction. In small plants where mine-run ore is reduced in a single step, either of these machines will do the work. In intermediate and fine grinding, various machines are used. The relative merit of the different types will be governed in no small measure by the size of the installation, the character of the ore to be reduced and the final product desired for subsequent treatment. It should be possible, nevertheless, with the data available, if properly classified, to arrive at an approximation of the relative efficiency of these intermediate and fine grinders. It should be possible, also, to determine the economic grinding range of the different machines. With this in mind, it will be the object of this article to indicate, in rough outline, how the data available may be classified, rather than to attempt to discuss any particular practice and compare the results with other practices. Conclusions or generalizations can not be drawn without an exhaustive classification of data; in fact, many vital points will have to be determined by additional experiments which can be carried on most advantageously in the laboratory. The expense en-tailed in such experiments would be worth while if the data obtained should lead to definite conclusions that would aid in standardizing and simplifying grinding practice.

Jan 2, 1923

By T. D. Yensen

AGING is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more con-stituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the Al transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, 0, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2.

Jan 1, 1935

By Merrill Horine

IT has been stated and accepted for many years that the automotive industry was the instigator, the principal sponsor for and the largest user of alloy steel and nonferrous alloys. The only universally recognized standard specifications and heat-treatments for these materials are those adopted by the Society of Automotive Engineers. It is this same auto-motive industry that has been the chief inspiration for and consumer of modern production machine tools. The production curve of steel ingots is more sensitive to fluctuations in automotive production than any other influence or group of influences. In every other important steel-con-suming industry, automotive materials and automotive processes are the outstanding features of modern progress. In this connection I need only mention the prefabrication of buildings, following the automotive system of straight-line, interchangeable mass production; the motorization of ships and railroads, employing automotive types of prime movers; the production of pressed-steel stoves, plumbing and furniture by methods originated in the automobile-body industry and the extensive use of rubber for the cushioning of all manner of machinery as pioneered by the automotive and tire industries. Dr. Jeffries has brought out this point in his address (p. 21), assuring us that the transportation industry is the largest user of these materials. In the transportation industry, or as we might more accurately express it, the transportation group of industries, the. automotive industry pre-dominates as a user of light alloys. One out of every four tons of aluminum produced is consumed by the automotive industry. Similarly, the automotive industry ranks first in the consumption of the following metallurgical materials: steel, 24.04 per cent; malleable iron, .57; alloy steels, 72.2; nickel, 30; lead, 39 per cent.

Jan 1, 1936

By George Smith

TWELVE years ago, the Director of the United States Geological Survey addressed to the Secretary of the Interior a letter calling attention to the government's need for liquid fuel for naval use and pointing out that the rate of increase in demand was more rapid than the increase in production.1 This letter, in a way, inaugurated the policy of public oil-land withdrawals, which was well founded in its primary purpose of protecting the oil industry and highly desirable in its immediate effect of checking the over-development of that day in California. Unfortunately, however, through delays in legislation, this policy may be regarded now as having outlived both its intent and its usefulness. In 1908, the country's production of oil was 178,500,000 bbl., and there was a surplus above consumption of more than 20,000,000 bbl. available to go into storage.: In 1918, 10 years later, the oil wells of the United States yielded 356,000,000 bbl.-nearly twice the yield of 1908-but to meet the demands of the increased consumption more than 24,000,000 bbl. had to be drawn from storage. Nor is this all of the brief comparison. In 1918, our excess of imports over exports of crude petroleum was nearly 33,000,000 bbl. whereas in 1908 we exported 3,500,000 bbl., which was net, as we had not begun to import Mexican oil. In this period, the annual fuel-oil consumption of the railroads alone has increased from 16,871,000 to 36,714,000. bbl.; the annual gasoline production from 540,000,000 gal. to 3,500,000,000 gal. This record may be taken not only as justifying the earlier appeal for Federal action, but as warranting deliberate attention to the oil problem of today.

Jan 1, 1920

By K. L. Temple, A. R. Colmer

ACID coal mine drainage presents a peculiarly difficult problem for two principal reasons. First is the fact that the amount of acid water discharged from active and abandoned mines constantly increases as coal fields are developed and thereby creates a steadily worsening nuisance of rapidly growing importance to the general public as well as to the coal industry. Second is the even more significant fact that there is no method yet known that will appreciably alleviate the acid water problem except at totally prohibitive cost to the coal operators. The problem is thus seen to be an urgent one. With a growing need for good quality water and a growing public demand for abatemknt of stream pollution, a large portion of the soft coal industry finds itself in the position of year by year dumping more and more acid into the streams and waterways and having no way in sight of improving the situation or even of keeping it from getting worse. While some studies have been made, it is only in the last few years that the problem has been seriously considered, chiefly by the group of workers under the direction of S. A. Braley at Mellon Institute and by the Bituminous Coal Research, Inc. fellowship at West Virginia University. Hinkle and Koehlerl reported the results of the earlier West Virginia work. This work pointed to certain biological aspects which had not been noticed previously. These may be summarized as two separate findings. One was that sulphur oxidizing bacteria were present in acid mine water and that their possible role in contributing to the acidity should be investigated. The other was

Jan 1, 1952

By J. J. Gilvarry

Recently, Gilvarry1,2 has given a rigorous derivation of the proper distribution function for fragment size in single fracture, based on a closely defined physical model and deduced strictly by the laws of probability. The physical point of departure is Griffith's theory of brittle strength, identifying sub-microscopic flaws as the cause of the low strength of a solid in comparison with values implied by cohesive energies. Gilvarry and Bergstrom,4-7 and Gilvarry8 have compared the predictions of the theory with experiment, and have found excellent agreement, in general. The purpose of this communication is to sketch the extension of the theory to the case of comminution, and to indicate the applications to some examples in nature. The present treatment represents an amplification of a brief discussion appearing elsewhere. 9 Although the basic ideas of the Griffith theory are perfectly general for rupture of brittle solids, it was originally formulated with very brittle materials such as glass in mind. Moreover, Griffith's original experimental work was carried out on glass specimens. Recently, however, the theory has been extended by race" to apply directly to rocks. This extension makes the theory immediately applicable to the materials generally of interest from the standpoint of comminution. GENERAL CASE To obtain the distribution function for fragment size in single fracture, three assumptions are made, that: 1) Fracture proceeds by activation of preex-istent Griffith flaws in the volume, faces, and edges of a fragment; 2) the distributions of flaws of these three types are independent of each other; and 3) activated flaws of a particular type are distributed at random, individually and collectively, in the sense of Fry.11 The last assumption implies that each distribution is separately of Poisson type.

Jan 1, 1964

By T. C. Atchison, W. I. Duvall, D. E. Fogelson

Dr. Clark has given an excellent resum6 of the recent theoretical re- search work that has been done on the generation and propagation of stress waves in various types of media.1 Unfortunately the dynamic properties of rock do not fit the assumed properties of the idealized media. As a result, none of the theoretical solutions for the generation of stress waves by applied pressures to interior boundaries of the spherical or cylindrical cavity appear to be completely satisfactory to explain experimental data. This fact does not mean that the theoretical work is in error. It simply means that the appropriate dynamic properties of rock have not been taken into account in the present theoretical derivations. Because of the difficulty of theoretically accounting for the crushing and cracking that takes place when explosives are detonated in spherical or cylindrical cavities, it seems advisable that future theoretical studies should attempt to separate the generation of stress waves from the propagation of stress waves. Perhaps if these two problems are separated, we may be able to solve one of them satisfactorily so that theory and experimental data agree. Dr. Clark's resumé of the research work on scaling and crater formation by point charges is aimed at obtaining a basic understanding of the physical theory of rock breakage, wave generation, and wave propagation. A cursory reading of Dr. Clark's paper shows that there is very little information summarized that can be used by the practicing engineer in the field of blasting. When problems become too difficult to solve theoretically it is always helpful to take the empirical approach and collect experi-

Jan 1, 1967

By W. T. Thom

Many able men have contributed to the subject of coal classification, and recent publications on the subject have indicated a crystallization of opinion in that connection which promises the development in the near future of a scheme of coal classification which will be of real and increasing value to coal producers and users, as well as to those interested in coal on more exclusively scientific grounds. It is obvious that such a classification must be simple; must be based upon readily ascertainable factors; and if properly developed will apply to the whole range of coals between peat and anthracite and not merely to certain types of coal. Many of the numerous schemes of classification proposed in the past have given quite satisfactory results when applied to the higher rank coals, but have broken down when applied to the younger coals of higher moisture, and, as previously pointed out by the writer,' this breakdown has been due to the practice of ruling out "moisture" as an essential component of the volatile matter reported in the customary proximate analysis of coal, whereas a review of the mode of formation and natural history of coal satisfies us that moisture is a normal and natural ingredient among its volatile constituents; and a knowledge of analytical practice shows that the "moisture" and "volatile matter" reported are both mixtures of moisture and volatile matter, rather than sharply differentiated distillation fractions. After an extended consideration of the subject the writer regards the conventional proximate analyses of coals as affording the information essential for a both practically and scientifically satisfactory c1assification—assuming that the coal samples compared have been collected and analyzed according to standard methods. Two variables are required for a workable classification, and these appear to be afforded by the calorific value and proportion of volatile constituents (including moisture) credited to the coal on an ash-free basis. The writer originally proposed that the figures used for classification purposes be those given for the "air-dried" and "ash-free" form of the proximate analysis,

Jan 1, 1930

By Ray Arms

This paper includes a brief classification of dry-cleaning devices, with a theoretical discussion of the principles involved. It outlines the methods of handling dust and screening difficulties at the McComas plant, as well as other plants that are being constructed and other dry-cleaning devices being developed. It describes the American Pneumatic Separator and discusses the sizing required, the effect of moisture in the raw coal, disposition of the middlings, and other aspects of the process. It gives s results of tests on various coals, and results of operation at Raton and McComas. DRY CLEANING, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group' also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc.

Jan 3, 1924

By C. E. Van Orstrand

AN intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it will be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. H. Emmons,1 minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. MATHEMATICAL THEORY In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be assumed that the intrusive is a large parallelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, t = o), which has the same thermal properties as the intrusive, is2,3 [ ] In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. 'v = temperature at point x, y, z, time t. vo = initial temperature throughout the intrusive, t = o. K = coefficient of thermal diffusivity. a, ß, ? are variables of integration. Put n = m in Eq. I, and we have [ ]

Jan 1, 1944

By F. C. Holman

It is desired in these notes to record a vein-phenomenon certainly unique in the writer's limited experience, and, as it seems to him, sufficiently rare to be worthy of mention. In the little mining camp of Forbestown, situated in the Sierra Nevada of California, it was announced one day, when the miners of the Cold Banks mine came off shift, that "washed gravel" had been struck on the 265-foot level. To those acquainted with that section and the character of the mine (a gold-bearing quartz-vein) this was a somewhat startling announcement; for, prolific as the State is, we are not in the habit of mixing up promiscuously our vein- and placer-deposits. However, the statement proved to have some foundation. The mine is located at an altitude of about 2700 feet, on the brink of one of the great canyons of erosion characteristic of the drainage of this range. A lateral ravine cuts the vein at right angles, thus making its general strike approximately parallel to the canyon at this point, and with a variable dip of from 20 to 40 degrees towards the canyon. The strong, well-defined vein, often 20 feet wide and more, presents nothing to distinguish it particularly from scores of others in the State, unless if be considered peculiar in the highly crystalline character of its quartz and the nature of the enclosing country-rock, which is metamorphic in the extreme, very hard, devoid of lamination, and in bedding so obscure that it might easily pass—at least on superficial examination—for one of the basic eruptives. Near by in the district can be found a series of slates common to the gold-belt of this range, and within the limit of the company's property is an intrusion of an acid eruptive. On an adjoining claim a granite shows itself. The mine is opened through an inclined shaft sunk on the vein. The ore carries both free gold and sulphurets, the greater part of its value

Jan 1, 1896

By W. T. Thom

In previous classifications of coal, it has been customary to regard moisture eliminated from coal samples between 20 and 100 C. as extraneous matter, rather than as a constituent part of the coal. It seems, however, that the physical character and use properties of the low-rank coals are directly related to the amount of such moisture present, and recent chemical work has shown' that such coals contain unstable groupings which decompose between 20 C. and temperatures somewhat above 100" C., with the splitting off of moisture. According to this view, the moisture eliminated from air-dried coal below boiling point is similar in all essential respects to moisture eliminated above 100" C., and is produced by analogous reactions; and inasmuch as the moisture given off above 100" C. has always been treated as a constituent of the volatile matter of coal, it would seem that consistent usage would include as a part of the volatile matter all moisture present as an essential component of the coal as it occurs in nature. As a matter of experience, it seems clear that the general physical and chemical characteristics of the low-rank coals are largely determined by or related to the moisture, whether chemically or physically combined, present in air-dried coal; it is also demonstrable by trial that the low-rank coals cannot be satisfactorily classified on a purely chemical basis by using the moisture free form of analysis. The low-rank coals of the western United States include numerous well-defined types, many of which were referred to in a classification proposed by Ashley,2 in which the physical and use properties of the coals were made the primary basis for their systematic grouping. When testing this classification by replotting analyses of these type coals according to the Seyler scheme of classification,3 a satisfactory parallelism between use properties and chemical constitution of the dry coal was found among

Jan 1, 1925

By K. M. Weigert

The position of the three-phase field between the alpha and the beta phases was established. The exact location differs from previous assumptions. The extremely high strength and hardness values were found near the phase boundaries of the ternary compositions. IN 1929, UenoL investigated vertical sections of the Ag-Cu-Zn diagram at constant silver and zinc values. From the evaluation of cooling curves and microscopic studies, he concluded that there was no evidence of a three-phase field in the solid state between the a and ,8 fields. The failure to find evidence for this field was due to the fact that it exists only in a very narrow range of compositions and requires special methods of heat treatment to establish phase equilibrium. In a later publication on the same subject Keinert2 rearranged Ueno's diagrams to conform with the basic phase rules. The existence of a three-phase field was postulated in the solid state between the a phases and the homogeneous ,9 phase between the Cu-Zn and the Ag-Zn binary border systems. The approximate location was based on a few microscopic observations of the structure and it was pointed out that the exact position could be determined only by a larger number of experiments. In the twenty years following these investigations alloys of Ag-Cu-Zn have become of general interest due to various technical applications, principally for brazing. In the course of an overall investigation of the physical properties of ternary Ag-Cu-Zn alloys the author found extremely high values of hardness and strength in alloys of compositions between the a and the yS fields. The exact location of the intermediate phase fields was established by the evaluation of more than a hundred cooling curves and microscopic mountings. Experimental Procedures Preparation of Test Samples: At the beginning of the investigation samples were chillcast into Vi in. diameter iron molds to determine hardness, strength, and the mechanism of primary crystallization. These

Jan 1, 1955

By Robert J. Linney

Reserve Mining Co. produces 5 million tons of iron ore pellets per year. The finished product runs about 65.50 pct Fe, with 7.75 to 8.00 pct SiO2. Less than 12 pct arrives at the blast furnaces smaller than 3/8 in. This plant was originally designed to produce 3.75 tons annually-not 5 million. To handle the increased tonnage a fifth fine crushing line was added, and some very minor changes were made.

Jan 9, 1959