Search Documents

By Robert Ammon

The milling practice at Mascot, at present, consists of dry crushing to % in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. is made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads.......................... 3.55 Jig concentrates................ 61.30 Jig tails......................... 0.80 Flotation concentrates........... 60.60 Flotation tails................... 0.09 Extraction..................... 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows: PEr Cent. Per Cent. Calcium carbonate.............. 48.11 Zinc sulfide.................... 5.43 Magnesium carbonate........... 35.36 Cadmium sulfide............... Nil Silica.......................... 8.73 Lead sulfide................... Nil Alumina....................... 1.04 Iron oxide...................... 1.33 Total....................... 100.00

Jan 1, 1925

By Charles T. Van Winkle

Until the advent of the porphyry coppers and the introduction of flotation which soon followed, crushing and grinding for many years proceeded along somewhat stereotyped lines, without important alteration in type of machinery. For the finer crushing and grinding, stamps, rolls, and various patterns of Huntington and Chilean mills were in general use. Ball-mills were in use abroad, but owing to their small capacity and the high cost of screens and steel, they never obtained much footing in the United States. Tube-mills were first introduced into the crushing departments of cyanide plants when it was found that for crushing finer than 30-mesh other types of crushing machinery were not efficient. In order to crush with one pass, these mills were made 18 to 22 ft. (5.5 to 6.7 m.) in length. Pebbles were used as a grinding medium and the mills were lined with either silex blocks or fragments of quartz or flint pebbles set in cement. While the cylindrical tube pebble-mill had been used to some extent in small installations of concentration mills, the first instance of its use on a large scale was at the concentrating plant of the Miami Copper Co., where 8-ft. by 22-in. (2.5-m. by 55.9-cm.) Hardinge mills were tried out against Chileans. The results of these experiments led to the gradual replacement of the Chilean by the Hardinge mill. Robert Franke published an article' describing the work done, comparing the two types of mills. At the same time, according to Franke, a test was run using a 6-ft. (1.8-m.) Hardinge ball-mill as a substitute for rolls for intermediate crushing on 1/2-in. material. According to Franke, this mill was soon discarded, since it was found that to obtain the desired product the mill must be limited in capacity. The Miami Copper Co. made no test with other types of ball- or pebble-mills. Following this example, others installed the conical type; and when the Inspiration Consolidated Copper Co. decided to build a concentrator, it adopted the conical mill. As the requirements for mills would be very large, it purchased manufacturing rights in the State of Arizona from the

Jan 1, 1918

By J. A. B. Forster

The operations of the Electrolytic Zinc Co. of Australasia Ltd. involve the preliminary roasting of zinc concentrate from Broken Hill, New South wales, at a number of acid-making centers on the Australian mainland. The partially roasted material is shipped to the Tasmanian plant where it was formerly re-roasted prior to leaching,' but this practice was gradually abandoned in favor of the flotation of leach residue for the recovery of a concentrate containing about 22 pct sulphide sulphur and known as secontlary or Risdon concentrate.2 This change, together with increased zinc production, called for new furnaces at Risdon for the roasting of 10-50 tonst of secondary concentrcite and 90 tons of new concentrate per day. The war situation made it imperative that construction be commenced without delay and to save time it was decided to base the design on that of Skinner type furnaces which had been built in South Australia twenty years earlier. This involved some sacrifice of desirable features but did not prevent the incorporation of provisions which had enabled small Herreshoff type furnaces to roast secondary concentrate autogenously. The roasting rate in existing furnaces was 10-12 Ib sulphide sulphur per sq ft of hearth area per day, and eleven hearths, 20 ft in diam, were provided in the two new furnaces in anticipation that they would prove capable of the autogenous roasting of 130-140 tons of concentrate per day from 28-29 pct sulphur down to 4.5-5 pct, with an oxidation rate of 11-11.5 lh S/S per sq ft of hearth area per day. It was soon realized, when the first of the furnaces went into operation, that a much better performance than this might be given, and the purpose of this paper is to show how a treatment rate of 100 tons per furnace day, and oxidation rates approaching 15 lb S/S per sq ft per day have been reached. Furnace Design General specifications for the design were based on the results of experience with several other types of furnace and on the special operating conditions

Jan 1, 1950

By Chester A. Fulton

APATITE, the most abundant crystalline phosphate mineral, is found in igneous rocks and probably is the primary origin of all other phosphates, whether mineral or organic. Its chemical formula may be expressed as Ca5(Cl,F) (PO4) 3. The chlorine may be replaced almost entirely by the fluorine. It is found in large or small hexagonal prisms, usually of a vitreous luster and a green or red color, but also violet, white, or yellow. It is found largely as an accessory mineral in granitoid rocks. Its hardness is 4.5 to 5 and its specific gravity is about 3.2. There are many other phosphate minerals-for instance, amblygonite, autonite, collophane, lazulite, monazite, pyromorphite, torbenite, triphylite, turquoise, vivanite, wavellite-with base elements of calcium, magnesium, iron, aluminum, manganese, lead, cerium, lanthanum, lithium, or several of these in combination and with various amounts of water of crystallization. However, these phosphate minerals have but little value save as specimens for mineral collections, the exception perhaps being turquoise. While large deposits of igneous apatite are mined today for the production of fertilizers and chemicals, more than 90 pct of the world phosphate production is derived from secondary apatites, called phosphorites. These calcium (and magnesium, aluminum, and iron) phosphates have been formed in the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rocks containing apatite, bone deposits of prehistoric animals and marine life, or guano deposits (excreta of birds). These phosphorites are mostly alterations of phosphatic limestones that took place slowly over many years. Whether it is apatite or phosphorite that is being produced, it is known in the trade as "phosphate rock." The sedimentary phosphate deposits are of marine origin. Some, as laid down, were rich in phosphate or have become so by subsequent subaqueous action and have not been further enriched since emergence from the sea. Some were originally phosphatic limestones or marls from which calcium carbonate was dissolved away by waters containing carbon dioxide, in which calcium carbonate is much more soluble than

Jan 1, 1949

By Murl R., Schrock

THE use of diamond-drill holes at the Moctezuma Copper Co., Pilares mine, Pilares de Nacozari, Sonora, Mexico, for the ventilation of raises has resulted from experiments that were made in an effort to secure continuous and efficient ventilation in hot and gaseous raises. The method is particularly applicable in long raises and in raises run from development levels where the source of fresh air is distant. In order that the CO, concentration shall not become excessive, 30 cu. ft. per min. per man must be supplied to a heading for breathing purposes:' The quantity of air that will pass through a diamond-drill hole by

Jan 1, 1929

By Robert Franke

In view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in. For the ore of this mine, a moderately hard but very fissile schist,

Jan 1, 1914

By Nev A. Gokcen

PUBLISHED data on the solubility of nitrogen in liquid manganese are widely discordant. Ochsenfeldl observed that a Mn-N alloy with 3.6 pct N consisted of solid and liquid phases at 1260°C but at 13 00° to 1340°C the solid phase disappeared and the liquid contained 0.1 to 0.13 pct N. In contrast Saito's measurements at approxhately 1400°C yielded an average value of 0.97 pct N. Sieverts3 volumetric method is not suitable for the determination of gas solubility in manganese because the liquid metal vaporizes readily and condenses in the cooler parts of the apparatus where it can absorb large amounts of nitrogen. The purpose of this investigation was, therefore, to determine the solubility of nitrogen in manganese accurately in the range of 1273" to 1500°C. The experimental method used in this study was as follows. Electrolytic manganese of 99.9 pct purity, and weighing 50 g, was melted in a pure alumina crucible placed in a tubular furnace. Temperature was measured with a Pt-10 pct Rh thermocouple and controlled within ± 5°C. Pure nitrogen was bubbled through the melt for 1 hr at constant temperature and then a sample was taken by sucking the metal into a 2-mm clear silica tube and immediately quenching in water. The sample was broken into small pieces and found to be sound to the naked eye. The entire sample was then dissolved and the resulting solution was analyzed for nitrogen by the well-known solution-distillation method. The experimental results are presented in Fig. 1. All the nitrogen solubility data refer to 1 atm of nitrogen pressure; hence the observed values are slightly corrected by using Sieverts' equation when the atmospheric pressure differed more than 5 mm Hg from 760 mm, and further, in the case of the runs at 1500°C the correction arising from the presence of Mn vapor has been made. (Cf. Eq. [3]). Scattering in the data is within ±5°C in temperature measurement and ±3 pct in total nitrogen analysis. The straight line in Fig. 1, correlating the percentage of dissolved nitrogen, %N, with the inverse temperature in OK-1, can be expressed by:

Jan 1, 1962

By M. Gensamer, B. Lustman

A recent paper described, by means of stereographic pole figures, the preferred orientations produced by cold-rolling low-carbon steel of automobile-body grade. It was found that the surface of the sheet exhibited a deformation texture significantly different from the texture possessed by the inside of the sheet. Efforts to produce the surface texture by buffing a sample exhibiting the normal or inside texture, using a copper lap, have not been successful. In view of the data collected by Kurdjumow and Sachs2, it was suggested that the surface texture might be the result of partial recrystallization of the normal or inside texture. The recrystallization texture of cold-rolled mild steel was studied by Goss3, but he did not use the pole-figure method, so that his conclusions were in need of verification. For these reasons the work reported in here was undertaken. It had two objectives: (1) to study the general behavior of cold-rolled mild steel on recrystallization below the critical temperature Al, and (2) to attempt experimentally a demonstaration of the genesis suggested above for the surface texture in cold-rolled steel. The material was that used by Gensamer and Mehl, cold-rolled to 97.5 per cent reduction in thickness. Fig. 1 is an X-ray pinhole photo-gram of this material, taken with the beam transmitted perpendicular to the plane of the sheet, using a molybdenum target at 35 kv. with no filter. It is typical of the inside texture, but in it the deformation texture is better developed than in the samples that showed a well developed difference between the inside and surface samples. Specimens from this sheet, which was 0.005 in. thick, were annealed for 5 min. at various temperatures in a lead bath. After about 0.0005 in. had been etched from both surfaces, X-ray photograms were prepared, using the technique described in the earlier paper1. Figs. 2 to 6 are photograms of the annealed sheet, at 566, 571, 577, 580 and 650" C. (1050' to 1202" F.), in order. Fig. 2 shows that 5 min.

Jan 1, 1937

By R. P. Rothwell

THE milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I have thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value and interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern ; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a wet stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulphides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80-stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is man¬aged in a skilful and economical manner, though the necessity for * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

J. D. Fast and J. L. Meijering (Philips Research Laboratories, N. V. Philips' Gloeilampenfabrieken, Eindhoven, Netherlands)— After the departure of our friend Dijkstra to the United States, investigations on the effect of alloying elements on the behavior of nitrogen in a iron were continued in Eindhoven. We too found internal friction curves with two separate peaks for iron containing nitrogen in addition to 0.5 atomic pct V or 0.5 atomic pct Mo. Our first publication on these investigations" appeared almost simultaneously with the paper now under discussion. At first sight our experimental results seem to be in harmony with their conclusions, but a closer examination reveals that in the case of the Fe-V-N alloy the abnormal peak is not controlled by one time of relaxation only. Whereas iron containing 0.5 atomic pct Mn or Mo absorbs an amount of nitrogen of about the same magnitude as that absorbed by pure iron under identical conditions, iron containing vanadium absorbs in addition one nitrogen atom for every vanadium atom. This last amount, far exceeding the first amount in the case under consideration, combines chemically with the vanadium and causes no internal friction. The "free" nitrogen in the vanadium alloy gives rise not only to a damping peak corresponding to that in pure iron but— due to the presence of VN particles in the metal—also to the abnormal peak at higher temperatures. The VN particles create interstitial sites around themselves where the free nitrogen atoms are bound much tighter than in the normal interstices. These abnormal interstices, therefore, will capture free nitrogen atoms rapidly, whereupon these give rise to the abnormal damping. The binding energy in the abnormal interstices is not the same for all, and with coarsening of the VN precipitate the distribution of these energies is displaced toward the side of stronger binding. This is deduced from a shift of the summit of the second peak toward higher temperatures (from 80" to 88°C in our experiments) caused by prolonged heating at 950°C. From the intermediate state where they cause the abnormal damping, the nitrogen atoms pass over rather rapidly into the fully precipitated state (iron

Jan 1, 1954

By Leonid V. Azároff, H. N. Murty

In the course of investigating the soft X-ray absorption spectra of Ni-A1 alloys, Das and ~zfiroff' observed an anomalous brittleness in solid solutions containing 3 to 5 at. pct Al. The brittle alloys also had anomalously larger lattice constants' and the fine structure at the nickel K edge of an alloy containing 3.96 at. pct A1 unexpectedly resembled that of NiA1 more closely than that of a solid solution containing 5.51 at. pct Al. This led them to suggest the possibility that short-range ordering was produced during the homogenization anneal to which each specimen was subjected, similar to that observed in dilute solutions of vanadium and of chromium in nickel: as the principal cause of embrittlement. It was decided to repeat the above measurements on several alloys in this composition range in order to test the above hypothesis and to establish the effect of heat treatment on the alloys' properties. Three solid solutions in this range were prepared containing, respectively, 3.16, 4.00, and 4.54 at. pct Al, in addition to alloys containing 6 and 9 pct. All samples were annealed in vacuum at 1800°F for 100 hr and then furnace-cooled to room temperature, as in the original study. The lattice constants of these alloys are shown by open circles in Fig. 1 and can be seen to fit quite closely the curve established by the previously measured values, indicated by solid circles. (The experimental errors are of the order of the size of the circles, +o.oo~R.) The three alloys containing 3 to 5 at. pct A1 were found to be quite brittle, as previously reported. In order to test the possibility of ordering, these three solid solutions were again heated to 1800°F and, following a few hours at that temperature, were quenched directly to room temperature. All three alloys lost their brittleness. In order to verify the proposed ordering hypothesis, it was decided to subject each sample to several cycles of quenching and annealing (disordering and ordering). After some experimentation, it was established that reproducible results could be obtained by anneal-

Jan 1, 1968

Discussion of the paper of R. H: Sweetser,. presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912 pp. 1327 to 1334. See also Bulletin 11 No. 72, December, 1912, pp. 1561, 1562. J. J. HOWARD, Dover, N. J. (communication to the Secretary*) :-No doubt there are as many different methods of starting a blast-furnace as there are men who assume that responsibility. Having blown-in a furnace a few years ago in a manner similar to that outlined by Mr. Sweetser, things went along so well at the start that I had time for a little reflection on what was going on inside the furnace. I saw the wood turned to charcoal practically, and it occurred to me, why should I use wood when I could put in the charcoal in the. first place, and thus save a lot of time, and also eliminate the dangerous gas from the wood, which is the cause of most of the accidents in starting up a furnace. I had a furnace out for repairs and decided to use no cord-wood in blowing in. I put in about a carload of charcoal and used no wood except some shavings and oily waste at each of the tuyeres. The furnace had 16 tuyeres and was 100 by 22 by 14.5 ft. Hot rods were put in each tuyere' and the blast started immediately at 11 a.m. Within 5 mill. the air was all driven out of the stack and the gas lighted of its own. accord at the top of the furnace. It was allowed to burn for 5 min. longer and then the bell was closed and the gas taken to the last stove and the last boiler on the gas-main. It was all clone so quietly that it was hard to realize that the gas was down. The tuyeres were as bright as if the furnace had been in blast for a long time. I have learned since that others have used the same method, but they had not passed the good advice along.

Jan 5, 1913

By Raymond Mancha

THE purpose of the Coal Division's Committee on Ventilation is to cover one principal aspect of mine ventilation thoroughly each year, instead of attempting to touch upon several different subjects. The Committee for 1943 consists of four members besides the Chairman. Members, selected because of both knowledge of the current topic of mine ventilation, and diversity of occupation, are: Carel Robinson, consulting engineer with an operating background; T. G. Fear, chief engineer for the Hanna Coal Co., an operator of varied experience in mine ventilation; E. H. Denny, chief of the coal mine inspection division of the U. S. Bureau of Mines, obviously well qualified; and C. M. Smith, editor of Mechanization with a background of mine ventilation study as a member of the mining department of the University of Illinois, at present retained as a ventilation consultant by the Climax. Molybdenum Co. of Climax, Colo.

Jan 1, 1944

By E. M. Wise

WHEN man became dissatisfied with the mere utilization of physical force and began to use weapons, he made a definite stride forward. At first he used sticks, animal bones and stones, often rudely shaped to some particularly lethal form. These devices, while crude, were moderately effective. How- ever, some of the brighter men of the tribe found that certain particularly heavy "stones" were somewhat ductile and could be hammered into more effective weapons than those previously known. Later, probably through the misuse of one of these weapons to stir the campfire, it was found that heating softened and perhaps actually melted the material. The process of annealing had been discovered! Smelting the more easily reducible metals was in all probability one of those fortuitous accidents which was followed up by thoughtful researchers who ultimately developed the technique of mixing various ores to produce bronze and even some of the nickel content alloys. The resulting products were at first lumps of more or less ductile material which could be hammered to shape, and were thus incidentally hardened by this process. The hardening of metals by alloying and cold working remained for many centuries the only known methods for improving their properties.

Jan 1, 1931

By Frank Firmstone

The furnace from which the brick here referred to were taken, was lined under my supervision and blown-in in May, 1902. It was 75 ft. high and 18 ft. in greatest diameter, and used coke to smelt a lean magnetic iron-ore. The lining was put in as follows:—First, blocks 14 in. long by 6 in. thick; second, 2 in. of loam; third, 13.5 in. of 9-in. fire-brick (one-and-ahalf brick wall) laid in English bond; fourth, red brick to within 2 in. of the iron shell; and fifth, 2 in. of slag-wool between the red brick and the shell. The brand of brick used has been known to me for over 20 years, and in my observation had always proved very durable, notably when used in a small furnace 50 k. high which treated the same magnetic. ore. On revisiting and examining the furnace in March, 1903, it was found that the whole of the lining of 14in. blocks at the top, and for an unknown distance (more than 20 ft.) below, had completely disappeared; and a few weeks later the 13.5-in. lining and the red brick at the top likewise vanished, and the furnace was blown out. N~twithstanding the complete failure of the lining higher up, measurements taken after blowing-out showed no unusual wear in the lower part of the furnace. The exact position in the furnace of the piece of brick-work used in the analysis, given below, is not known; but it came from between 30 and 40 ft. above the bottom. It had formed part of the 13.5-in. wall (no 14-in. brick remaining at that level) and consisted of parts of several bricks so firmly sintered together that fracture occurred indifferently through the joints and through the body of the brick. The joints could, however, be traced by a close examination. The surface which had been in contact with the material in the furnace was covered with a yellowish, translucent glaze, somewhat vesicular, and from

Jan 1, 1904

By AIME AIME

SECTION DELEGATES were given an opportunity to see how the machinery of Institute administration functions, on Tuesday evening, Feb. 16, when they were the' guests at the regular monthly meeting of the Directors. Of the new board of 25 members, 19 were present at the meeting, including directors from Seattle, Los Angeles, Wyoming, Oklahoma, Chicago and Pitts-burgh, the new junior past-president from Jerome, Ariz., and the new president from .Washington, D. C. The complete list of the 72 in attendance at the dinner,: held in the main dining room of the Engineers' Club, which pre-ceded the general session of the Directors'. meeting, follows:

Jan 1, 1932

By Freeman Bishop

Having obviously cleared the way for fast confirmation by the Senate Interior Committee, the Administration recently named Elburt F. Osborn, vice president of Penn State University, as director of the Bureau of Mines. Interior Committee Chairman Henry M. Jackson (D of Wash.) has moved hearings on the nomination right along, forecasting that they will end in a confirmation. Dr. Osborn not only made a good impression on the Committee, he also made it amply clear that he would be the boss of his job and have right-hand aides to help straighten out conflicts stemming from recently enacted health and safety regulations for miners. Mining engineers in the field hope this clarification can come soon. They are frankly fed up with local, state, regional and national overlapping of restrictions.

Jan 1, 1970

By AIME AIME

AWRDED jointly by the four AW Founder Engineering Societies the John Fritz Medal is generally regarded as the most signal honor that American engineers can confer on a fellow engineer. The roll of 34 recipients contains the names of Lord Kelvin, George Westinghouse, Alexander Graham Bell, Thomas. A. Edison, George W. Goethals, Guglielmo Marconi, and Michael I. Pupin; and among members of the A.I.M.E. now living, Sir Robert A. Hadfield, Herbert Hoover, and Daniel C. Jackling. On the evening of March 1 7 the name of Paul Dyer Merica was formally added to this list of illustrious engineers when the medal was presented to him at a dinner at the Metropolitan Club in New York. The citation read. For important contributions to the development of alloys for industrial uses. Arrangements for the dinner were made by the following committee representing the four Founder Societies: R. C. Allen, George S. Davison, A. A. Potter, and J. B. Whitehead.

Jan 1, 1938

By Joseph B. Umpleby

WHEN the Cushing field flooded the oil market in 1914 and 1915 with a daily output equal to nearly one-third of the world's production, the situation was soon corrected by increased consumption, and the price of crude oil rose from 45 c. per barrel in, February 1915 to $1.10 in December of the same year-the highest price paid in the Mid-Continent field up to that time. The intensive search for oil during the following seven years failed to disclose a single new ,field equal to Cushing, and many observers concluded that the rapidly increasing number of wells contributing to the world's output, each declining roughly 20 per cent. a year, combined with the rapidly increasing con¬sumption of petroleum, made it highly improbable that any field would; be found again sufficiently large to seri¬ously affect the oil market. That seven exceptional fields should then be discovered simultaneously is a remarkable coincidence. Long Beach, Santa Fe Springs, and Powell, each exceeded Cushing in daily output and reached the apex of their production during a year when Burbank, Tonkawa, - Smackover and Huntington Beach each contributed several times the daily output of the average new pool. This unexpected and tremendous flood of flush production could only have the effect of depressing price and greatly adding to stocks throughout the country. It was particularly depressing in the Mid-Continent as the new oil from California proved of attractive refining grade and because of cheap transportation by water easily undersold Oklahoma crude in the eastern markets.

Jan 1, 1924

By AIME AIME

AMONG the European nations Germany is the center of interest economically as well as politically, and of prime importance for Europe as a whole is Germany's capacity to produce mineral products for armament and for export in exchange for the import of the essential supplies to maintain its industries. So far as minerals are concerned, Germany is worse off than any other great power except Italy, and deficiencies are being met by attempts to increase output from local deposits and by greater use of substitutes derived from domestic raw materials to replace imported metals, petroleum products, and other minerals.

Jan 1, 1939