Search Documents

By C. P. Kempter, H. L. Brown

Recently Chang determined heat content values of tantalum monocarbide and tungsten monocarbide from 325" to985°Kand 326" to 912"K, respectively, and, using other published data, made certain solid-state calculations for these two compounds. Chang expressed his Cp values in units of cal per "g-atom alloy" OK. We consider this poor usage since l) tantalum monocarbide and tungsten monocarbide are not alloys, and 2) an atom of an alloy does not exist. However, one may convert his values to units of cal per mole OK by merely doubling them. For TaC he calculated a Nernst-Lindemann parameter of 9.07 x lo-' "g-atom per cal". We have refined the calculation of this parameter and have arrived at a much lower value. Rather than approximating the true coefficient of volume expansion, a,, as three times the true coefficient of linear expansion, a, we calculated u, from the TaCo.99, lattice expansion data of Fries and Wahman.38 At 25°C a, = 14.3 x 10s per OC. The molar volume was calculated to be 13.32 cu cm per mole at 25°C. From the lattice compression data of Champion and Drickamer~' for "TaC,.,," we determined the room-temperature compressibility to be 3.5 x 10-l3 sq cm per dyne by plotting l/Vo (aV/ap) vs applied pressure. (Since the lowest pressure at which Champion and Drickamer reported a relative volume was 20 kbars, one may calculate an approximate compressibility only. Chang calculated a compressibility of 3.175 x 10-l3 sq cm per dyne from the same data.) We also used twice Chang's value of Cp = 4.38 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated a Nernst-Lindemann parameter of 5.8 x 10-l4 mole per erg or 2.4 x lo- ' mole per cal, and a Cdil value of 2.3 x 10' ergs per mole OK. In the case of tungsten monocarbide no isothermal compressibility has been reported; however, one may calculate an approximate Nernst-Lindemann parameter by using the adiabatic compressibility reported by Brown, Armstrong, and Kempter." Using the WC lattice expansion data of Mauer and Bolz~l we calculated a, to be 12., x l0-' per OC. The molar volume was calculated to be 12.5 cu cm per mole. We used twice Chang's value of Cp = 4.18 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated an approximate Nernst-Lindemann parameter of 2 x lo-' mole per cal, which is much

Jan 1, 1969

The Bougainville ore body was discovered in 1964 by a partnership of Conzinc Rio Tinto of Australia and New Broken Hill Consolidated Limited. The ore body is a porphyry copper in a fine-grained quartz diorite, which intrudes andesite volcanics and is located at an elevation of about 2, 000 ft in the Crown Prince Range of Bougainville in the Solomon Islands. Mineralization is predominantly chalcopyrite with some bornite and some gold and silver present. Rainfall in the area amounts to 200 in. (5. 08 m) per year. An active volcano is situated only 24 miles (38.4 km) from the mine, and all structures were designed to resist seismic shocks. An interesting and unique feature of the Bougainville operation was that the overburden was stripped with hydraulic monitors. Bougainville Copper, at 90,000 tpd, is the largest copper concentrator to be designed and constructed at one time; and besides the twin 54 in. by 74 in. Allis-Chalmers gyratories, it features seven 7 ft (2. 13 m) standard and fourteen 7 ft shorthead crushers, in addition to nine 18 ft diameter by 21 ft long (5. 5 m by 6. 4 m), 4250 hp, single -stage ball mills. During the design stage of the Bougainville primary crushing plant, several alternates were studied because the ore was expected to break with the production of large amounts of small-sized particles but with a minimum of fines. These alternates included two 54 in. by 74 in. gyratories with grizzlies, two 60 in. by 89 in. gyratories, and one 72 in. by 96 in. gyratory, the latter two installations without grizzlies. The two 54 in. units with grizzlies were finally selected as giving good reliability and the ability to handle the large amounts of small material in the feed. As originally installed, grizzly bars were set at 8 in. (203 mm); but, in an effort to perform more interparticle crushing in the primary and less rock-on-steel crushing in the secondaries and tertiaries, a test is underway (1976) to determine the effect of using 6 in. (152 mm) grizzly spacings (see write -up on Anaconda's crusher at Butte). The Bougainville ore is mined with 17 cu yd (13 cu m) shovels and hauled in 105, 170, and 210 st trucks to the crushers, which are equipped for two-side dumping. Up to 40% of the ore passes the grizzlies, which are equipped with splitters; and additional horizontal splitter bars are located directly above the spider caps. Because of the grizzlies, the crushers are supported by unique U-shaped enclosures, which are in turn supported by the end and center walls of the installation.

Jan 1, 1978

By M. A. Bryant, J. C. Goodwin, T. B. Faddies, L. D. Kornze

The Mercur Gold Mine is located 56 km (35 air miles) southwest of Salt Lake City in north central Utah; In July 1981 Getty Mining Company made the decision to put Mercur into production. The first gold bar was poured in April 1983. This paper provides details on: 1) the history of the camp, 2) past production, 3) geology of the deposit, 4) the exploration and development program, 5) ore reserve estimates, 6) detailed geologic pit mapping, 7) production blasthole sampling techniques and 8) the use of geostatistics (kriging) in handling assays and gold extractions to produce the required mill feed.

Jan 1, 1985

By Roderick K. Davey

Introduction in any business, it is essential that we select those alternatives which are not only technically feasible, but will be the most profitable to the business m terms of corporate objectives Some of the studies and activities requiring support of financial analysis to select the alternatives which most closely satisfy the management objectives and technical considerations are as follows 1 ) Cutoff grade determination. 2) Ore reserve estimation. 3) Production forecasts (long- and short-term) for an operating mine, development of a new mine, or expansion of an existing mine. 4) Evaluation of haulage alternatives. 5) Evaluation of equipment.

Jan 1, 1979

By L. R. Testardi, J. R. Wiese

OBSERVATIONS have been made that the substitution of antimony for bismuth in Bi2Te3 leads to anomalies in some of the electrical and magnetic properties of the Bi2Te3-5S2TeS alloy system at the composition ratios 2 Bi2Te3 : 1 Sb2Tes and 1 Bi2Te3 : 2 Sb2Te3. Airapetiants and Efimova1 have reported the peaking of the nondegenerate hole mobilities, at these compositions for sintered materials and ascribe the peaking to the formation of ordered alloys. From a study of these materials produced by the Bridgeman

Jan 1, 1962

By M. P. Board, M. J. Reus

Instrumentation was installed during construction of the Silver Shaft in northern Idaho to evaluate lining behavior and rock deformation. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gages. Rock displacement data from the 5,955-ft level indicate rock mass anisotropy. Liner stress and strain data reflect high in situ stresses and nearby station and raise construction. Continued monitoring and preliminary analysis indicate that concrete-lined, circular shafts are stable for high, unequal stress fields and anisotropy in deep level mines.

Jan 1, 1984

By J. H. Allen

The air lift method of pumping water is discussed. A review of several large diameter hole drilling projects that used reverse- circulation air-lift techniques is presented. Proposals are made for reverse circulation flow rates for slow rates of bit penetration (5 fph) as well as reverse-circulation flow rates for faster rates of bit penetration (10 fph). The Ingersoll-Rand air lift equations are modified for rotary drilling operations. By establishing minimum reverse circulation flow rates and utilizing the modified air lift equations, the establishment of minimum circulation equipment sizes and a more definitive requirement for improved bit body design should result.

Jan 1, 1978

By G. A. Josey, T. P. Floridis

INFORMATION on the effect of alloying elements on the solubility of sulfur in solid iron alloys is limited to the effects of carbon,' manganese,' and Silicon.Refs. 3 to 5 provide information on the combined effects of silicon and manganese also. In the investigation reported in this communication, the effect of chromium, copper, nickel, and vanadium on the solubility of sulfur in solid iron was determined at 1000". The specimens for this investigation were prepared by melting electrolytic iron and reagent-grade alloying additions in an induction furnace under an argon atmosphere. The melts were allowed to solidify in

Jan 1, 1969

By B. R. Eichbaum, J. E. Murphy, J. A. Eisele

The US Bureau of Mines demonstrated ferric chloride leaching of galena concentrate on a continuous bench scale basis. Leaching was performed at 95°C (200°F) and with a contact time of 15 minutes. The ferric chloride leaching solution was continuously fed to a leaching tank at a constant rate for periods up to 45 hours. In each test, a constant redox potential was maintained in the slurry exiting the leaching tank by controlling the concentrate feed rate. In the 45 hour test, lead extraction exceeded 99.5%, and the lead chloride produced was 99.97% pure.

Jan 1, 1986

By R. Chanchani

It was reported earlier that francolite and dolomite from south Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved after reconditioning at a pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption, and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1986

By D. P. Seraphim

Single crystals of bee Li-Mg solid solution were grown and their internal friction was measured as a function of temperature, A peak of the Zener type was found in the damping spectrum. The activation energy for the relaxation process is 21.5 ± 1 kcal per mole and the frequency factor is 1015.7 ± 0.7 sec-1. ZENER internal-friction peaks which are observed for a wide range of solid solutions are attributed to stress-induced changes in local order.' In the present work a Zener internal-friction peak, the first reported for a solid solution of an alkali metal, is

Jan 1, 1961

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham, Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By R. J. Wasilewski

OBSERVATIONS have been made that the substitution of antimony for bismuth in Bi2Te3 leads to anomalies in some of the electrical and magnetic properties of the Bi2Te3-5S2TeS alloy system at the composition ratios 2 Bi2Te3 : 1 Sb2Tes and 1 Bi2Te3 : 2 Sb2Te3. Airapetiants and Efimova1 have reported the peaking of the nondegenerate hole mobilities, at these compositions for sintered materials and ascribe the peaking to the formation of ordered alloys. From a study of these materials produced by the Bridgeman

Jan 1, 1962

By James M. Henderson, John B. Pfeiffer

The recently completed liquid sulfur dioxide plant at American Smelting and Refining Co.'s Tacoma copper smelter in Washington last April is one step by the firm to meet ambient air quality standards in the vicinities of its three US copper smelters. At a capital cost of $18.5 million, the liquid SO2 plant will work together with an existing sulfuric acid plant to treat all gases generated by the copper converters. Designed to handle up to 45,000 cfm of converter gas utilizing the Dimethylaniline (DMA) process, this plant is expected to recover about 51% of the total smelter input.

Jan 11, 1974

By T. Y. Yan, W. F. Espewheid

The various ion exchange reactions occurring during restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column wing lime saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500-3 mg/L (29- 0.18 gr per gal). The essence of NaCl in the restoration fluid at levels in formation water is beneficial in improving the selectivity of the system for NH4+ removal and reducing Ca + + ion consumption

Jan 1, 1984

By Louis Stott

IT is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halske6 reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys.

Jan 1, 1936

THE National Safety Council will hold the following ses-sions in the Waldorf-Astoria Hotel, New York, N. Y., on Oct. 2, 3 and 4: Oct. 2. 9.30 A. M. 1. Report of past year committees, by Chairman 2. "Safety Pays," by Howard I. Young, Vice-President, American Zinc, Lead and Smelting Co., Mascot, Tenn. (Discussion) 3. Entertainment 4. "Methods and Results of Improved Foremanship Conferences," by H. A. Gilbertson, Director of Per-sonnel, Lehigh Coal and Navigation Co., Lansford, Pa. (Discussion) 5. Appointment of election and resolutions committees Oct. 3, 9.30 A. M.

Jan 9, 1928

By R. C. Dorward

DIFFUSION considerations are necessary to describe many technologically important metallurgical and physical processes. Since most commercially important alloys are comprised of more than two components, diffusion calculations applicable to binary systems are often unjustified. However, in many instances the more general equations valid for three-component systems may be employed. The phenom-enological description of ternary diffusion is now well-established,1-4 and the theory has been applied with some success to a few practical situations.5"7 The flux equations for the solutes (components 1 and 2) of a ternary solution may be expressed by:

Jan 1, 1969

* Phosphate from the Maiden Rock deposits in the Missouri River Basin, Mont., are to be developed by the Victor Chemical Works of Chicago. A $5 million plant for processing the rock into elemental phosphorus is to be constructed in the vicinity of Butte. The plant will receive power from the Bonneville Power Administration. * Tests are being made to determine whether iron pellets from taconite concentrates will boost blast furnace and open hearth output at the Campbell Works of the Youngstown Sheet & Tube Co. About 35,000 tons of iron pellets have been shipped from Minnesota for this purpose.

Jan 2, 1951

By N. A. Parlee, A. E. Lord

Measurements of the solubility of lead in liquid iron were made at 1550°, 1600°, 1650°, and 1700°C using two different methods, i.e., 1) liquid iron-liquid lead equilibration and 2) liquid iron-lead vapor equilibration. LEAD was long considered insoluble in liquid iron1. Today steels containing 0.15 to 0.35 pct Pb are used. One laboratory has found a solubility of about 0.5 pet in the 1600°C range. Recently Miller and Elliott2 gave 0.60 pct as the result of one determillation at 1540°C. Because these findings resulted from the

Jan 1, 1961