Search Documents

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

Coal - Surface Mining Coal Preparation Coal Utilization Research and Development Health and Safety

Jan 3, 1976

By F. W. Jessen, James N. Howell

The accumulation of paraffin deposits in tubular goods has been recognized as a major production problem since the inception of the petroleum industry. This problem is not limited to any particular geographical area nor is it limited to a specific type of crude oil.' Generally speaking, "paraffin" deposition pertains to the deposition of any predominately organic material in flow lines, and possibly even at the sand face, which would hamper the production of oil. In some fields, a continuous effort is required to remove deposits of paraffin and in order to accomplish this, many unique methods have been devised. The best solution to this problem, however, is to prevent the formation of such deposits. One method which has been tried in a number of fields is the use of plastic pipe. The purpose of this investigation is to compare the relative effectiveness of several plastic materials to aid in the reduction or prevention of paraffin accumulations in surface flow lines. COMPOSITlON OF PARAFFIN DEPOSITS By definition, paraffin deposits are those materials which are insoluble in crude oil at the prevailing producing conditions of temperature and pressure. Such deposits1 s usually consist of small particles of petroleum wax intermixed with resins, asphaltic material, and crude oil. They may also contain a variety of foreign materials such as sand, silt, water, various metal oxides, sulfates and carbonates of iron. barium, and calcium. The petroleum waxes deposited in flow strings usually consist of both a "hard" and a "soft" wax fraction. These waxes are largely aliphatic hydrocarbons with smaller amounts of aromatic and naphthenic compounds. Nathan' has classified the hard and soft wax fractions. The aliphatic hydrocarbons present are those of high molecular weight with high melting points. Reistle3 pointed out that these high molecular weight compounds first separate from the oil due to a sharp decrease in solubility as the melting point increases. The identification of the resins and asphaltic materials rests, at present, on an arbitrary solubility procedure. Under certain conditions, materials which are insoluble in pentane (ASTM D-893) are defined as resins and asphalts. Subgrouping of these materials is made on decreasing solubility in benzene and carbon disul-fide. Shock' found some correlation be-tween the solvent response and the pentane insoluble content of paraftins: higher pentane insoluble fractions are less soluble in any of the commonly used commercial solvents. PARAFFIN CONTROL METHODS The methods used in oil fields to prevent and remove paraffin accumulations can be grouped into four general classes: (1) operative methods, (2) physical methods, (3) chemical methods, and (4) combination of any of these. Operative methods attempt to prevent the formation of paraffin deposits while the other methods are concerned primarily with the removal of these deposits. Plastic coated pipe has been used for a number of years to prevent cor- rosion in wells, and in manv instances paraffin deposits have -been greatly reduced. Field observations have indicated that plastic coated pipe not only reduced paraffin accumulation but in some cases eliminated deposition completely; however, data are needed to demonstrate the relative effectiveness of plastic materials. Deposition Apparatus The pipe used to determine the effect of velocity on rates of deposition was %- and 2-in. nominal diameter, and 5 ft in length. Steel, butyrate, rigid PVC, kralastic resin-type plastic pipes, epoxy coated pipe, PVC lined glass fiber pipe, and aluminum pipe were tested. Steel pipe was used as a control. Fig. 1 is a schematic diagram of the apparatus showing the relative position of the separate units making up the equipment. In order to facilitate the installation and removal of the test pipes in the apparatus, O-ring seals capable of sustaining pressures of 50 psi were provided at each end. Test pipes were submerged in a cold water bath maintained at or below room temperature by circulating water through copper cooling coils packed in ice. A hot water bath equipped with immersion-type heaters, stirrers, and a thermoregulator was used to maintain the temperature of the oil prior to introduction into the piping manifold. The capacity of the oil reservoir was 30 gal. A 33-gal/min centrifugal pump, capable of producing turbulent flow velocities in the test pipes, was used to circulate the oil through the system when using %-in. pipe; and a 70-galjmin centrifugal pump was used in later tests using 2-in. pipe. A by-pass arrangement made it pos-

By C. K. Leith

OTHERS here are far better qualified than I to discuss some of the specific proposals for government regulation of the oil industry. I shall make no attempt to carry oil to Oklahoma. The question of public control, however, is inherent in other branches of the mineral industry in varying degrees, and my comments will be directed mainly toward some of the trends affecting the mineral industry as a whole, as a background for your more specific consideration of oil legislation. A proud American tradition has been the insistence on freedom of competition, on equality of economic opportunity, on a policy of laissez faire. Nowhere has this principle been given wider application than in the mineral industry. The mineral field has been open to all comers, and the job of mineral exploitation has naturally attracted daring and independent spirits. The laws governing conditions of discovery and development, as well as the anti- trust laws, have been devised to foster the spirit of private initiative. The result has been the building of a mineral industry on a scale never before approximated anywhere in the world. The impetus thus gained, the methods, the technique, the financial resources, have been projected be- yond our boundaries and have made the American mineral industry the purveyor to the world for many essential commodities and first in the exploitation of the world's minerals. Our habits of individual self-reliance and success are deeply ingrained, and there is hardly an individual in the entire mineral field who does not instinctively recoil fro111 the extension of collective control, whether public or private.

Jan 1, 1932

By J. R. Finlay

BEFORE entering into the statistical part of this article, some general comments may be ln order. Each important war seems to introduce a new atmosphere and a new epoch. The Civil War led to the period of great interior development in North America, of the transcontinental railroads, and of large-scale manufactures. The first World War introduced the general use of the automobile, the building of a huge network of highways, the radio, and household engineering. Now I expect World War II also to introduce some new ways of living. Transocean aviation will become a commonplace; we shall probably have much more of an eye to our military and naval establishments and be more conscious of Eastern Hemisphere affairs instead of thinking so exclusively of the Western. Each war has also multiplied government expenditures and taxes; and to this rule the present one will certainly be no exception.

Jan 1, 1944

By F. H. Buttner, E. R. Funk, H. Udin

Gold wires, 5 mil in diam, are found to creep viscously up to approximately 5.5x106 dynes per sq cm around 1300°K. Beyond this point, an additional slip mechanism appears. The average coefficient in the viscous range at these temperatures is 18.9 ± 7x10 12 poises. This observation and other visual observations made during the experiments agree with Herring's predictions. EARLY creep studies by Chalmers on single crystals of tin produced some of the first experimental evidence to suggest that metals deform viscously under very light stresses. That is to say, over a small initial stress range up to 150 g per sq mm, the single crystals of tin elongated at a rate proportional to the stress. The proportionality constant between strain rate and stress is by definition the coefficient of viscosity. Chalmers named this range of proportionality the microcreep range. One of the first theoretical attempts to explain the microcreep phenomenon was given by Kauzman,' who applied Eyring'sQ eneral statistical mechanical theory of shear rates to creep data then available. From the rate theory, he deduced the general hyperbolic sine law for shear rate on the assumption that the distortion of the reaction path due to stress is negligible and that the system is an infinite continuum. In order to fit the available data to the equation, it was necessary to assume that creep occurs by shear of rather large blocks of material, rather than by an atomistic shear process as in diffusion. The size of the shear units was shown to increase with increasing temperatures and lower stress, or lower strain rates. In applying the hyperbolic sine law equation to the microcreep data of tin, it was shown by Kauzman that the unit shear blocks became quite small, which suggested to him that microcreep might be a self-diffusion process. Making this an assumption, Kauz- man reworked the rate theory and arrived at an equation where the shear rate is proportional to the stress. In the form of viscosity coefficient, the equation is: o- _ \LkT V = 2qAlA where u is the stress; S, the shear rate; X, the distance in shear direction moved by flow units relative to one another in the unit process; L, the distance between layers of units of flow; T, the absolute temperature; k, Boltzmann's constant; qAL, a constant proportional to the size of flow units; and kT A, the diffusion coefficient = ------kTe-Q/RT = K X2 h Kauzman applied the expression to molten lead with a fair degree of success, the calculated viscosity being low by a factor of four. For solid lead the result is 5000 times too high. Taking q = 1, and X = dA = L = 21 = nearest neighbor distance, Udin, Shaler and Wulff8 found the equation low by a factor of lo7 for solid copper. On the basis of the discrepancy in lead, Kauzman indicated that microcreep is probably not a simple diffusion process of molecular shear units, but one involving preferential diffusion paths, or even that diffusion in solids does not involve shear at all. Cottrell and Jaswon4 treat the microcreep phenomenon on the basis of slow moving dislocations and apply it to Chalmers' data on tin with fair success. Nabarro Suggested a microcreep model in which mass movement in the direction of pull is effected by the diffusion of holes. The tension on the crystal effectively creates a greater hole concentration at regions near the crystal surfaces perpendicular to

Jan 1, 1953

By J. G. Thompson

PROJECT 8411 of the U. S. Bureau of Standards, sponsored by the Iron and Steel Division of the A.I.M.E., is an attempt to define more concisely than has been possible heretofore the accuracy and the Limits ' of usefulness of the ' various methods now in use for the determination of oxygen as it exists in ferrous materials. It originated in correspondence between John Johnston and other metallurgists, and was brought to the attention of the Iron and Steel Division of the Institute at the Annual Meeting in February, 1933. As reported in MINING AND MET,ALLURGY, Vol. 14, page 152, March, 1933, "Dr. Johnston introduced, and those present adopted, a resolution that the Iron and Steel Division of the A.I.M.E., believing that a careful comparison of the several methods now in use for the analysis of steel for nonmetallic elements such as oxygen is highly desirable, heartily endorses the proposal that the U. S. Bureau of Standards act as a clearing house " in this matter, undertaking the final preparation and allocation of identical samples to those laboratories willing to collaborate in this important question, and collate the results re- ported back to the Bureau.'"

Jan 1, 1934

By AIME AIME

DREAMS do come true at times, although it is evidently better to believe in engineers than to "believe in fairies" if most dreams are to be translated into fact. It was a fine dream that David H. Moffat had when he projected a railway directly west from Denver; a dream of opening a new empire in northwestern Colorado, and of quickening transportation from the Middle West to the Pacific slope. But Moffat had been a miner and had become a banker. He knew that dreams, untranslated into works, benefit no one and pleasure only the dreamer, so he employed an engineer, H. A. Sumner, to study and plan the route to be followed by the rails. Previous main lines had run to the north, the Union Pacific, or the south, the Santa Fe. The Denver and Rio Grande, it is true, wriggled its way bravely across Colorado but, in order to reach a point 74 miles in an airline west of- Denver, travelled 281 miles following two canyons and crossing Tennessee Pass at 10,240 ft. Valuable as such a road is, it could never accomplish what Moffat had in mind. It was known that no low pass could be found directly west of Denver but up to 9000 ft. the topog-

Jan 1, 1925

By Morris M. Fine, Norwood B. Melcher

It is out of the question, at this time, to select any one prereduction process as superior to the others. It is apparent that several share a basic similarity and that within the groups listed in Part 1, the reduction vessel is sometimes the only significant variable. Claims as to the virtues of one machine over another are difficult to substantiate: one may be rapid, another thermally frugal. Based on published data, however, all seem to be performing adequately. It would appear that processes based on carbonized pellets are most applicable to foundry iron at low production rates. Adaptation to large scale manufacture of blast furnace hot metal or to agglomeration of fine concentrates at the mine site is much less likely.

Jan 8, 1966

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs, and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

By Carl Zapffe

THE object of the Bradley process is to free manganese oxide from its associated gangue and separate the contained iron oxide by dissolving the manganese and precipitating it from the solution. 'The fundamental features of the process are : making. both 1 a manganese ore and an iron ore; effecting a separation of manganese .and. iron by means of selective roasting; leaching- the manganese from the roasted ore by using ' ammonium sulfate; precipitating the manganese by using the ammonia gas generated during leaching; fixing the precipitate by oxidizing with air; breaking down and reforming the ammonium sulfate, so that daily very little additional ammonium sulfate beyond that originally charged into the system is required; washing the manganese precipitate and the iron-silica residue and evaporating the liquor to conserve the dissolved salts in the moistures of these two products and 'to reduce the sulfur content,; drying the precipitates; magnetic wet-concentration of the iron-silica residue; sinteriny the manganese-and .the' iron-concentrates.

Jan 1, 1929

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. B. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 158, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfleld Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction 1-18th St. S. W. B'ham, Ala., Phone 56-5566]

Jan 1, 1952

By E. S. Davenport

WHEN annealed carbon, or low-alloy, steels are suitably heated the ferrite (alpha iron solid solution) and the carbide, of which they are composed, react together to form a single solid solution of carbon (and other elements) in gamma iron (austenite). This reaction may begin only at a certain minimum temperature called the eutectoid temperature. The first ferrite and carbide thus to react together do so in definite proportions known as the eutectoid composition. With further heating the original constituent that is present in excess is dissolved in the austenite until exhausted. Whether the excess constituent be ferrite (hypoeutectoid steels) or carbide (hypereutectoid steels) the procedure is much the same, and upon slow cooling the homogeneous austenite expels the excess of either (proeutectoid ferrite or carbide) until the eutectoid composition is reached. Thus the reaction upon heating is strictly reversed upon cooling and accordingly an equilibrium diagram of this process may be constructed. Such an equilibrium diagram concerns itself only with the tempera¬tures involved and with the proportions and compositions of the phases developed under conditions that suffice to permit equilibrium. Specifically it has no concern for the type or mode of distribution of these constituents nor with any extra-equilibrium conditions such as undercooling, which is almost universally encountered in metals. Actually, however, of great importance is the sluggishness toward equilibration caused by the not inconsiderable time involved in diffusion. Thus instead of the theoretical transformation point AE, we find for a certain rate of heating or cooling the use of the designations Ar and Ac (transformation temperature found on cooling and upon heating). These figures obviously have no particular meaning except as measured and expressed for a definite heating or cooling rate, and represent the apparent temperature displacement caused by an inadequate time allowance. In this paper are presented the results of a study of the time required for' the transformation of austenite to ferrite and carbide at a variety of temperatures and also of the time required for the reaction austenite ?martensite at the temperatures at which this reaction occurs instead of

Jan 1, 1930

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcade Bids. Santa Barbara, Calif.]

Jan 1, 1952

By Thomas T., Read

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for ,this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1893, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 30 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1893 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. d., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfield Bldg. Santa Barbers, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I. 18th St. S. W. Wham, Ale., Phone 56-5566]

Jan 1, 1952

By S. A. Swensrud

NINETEEN Thirty-Six was the biggest year in volume in the history of the oil industry, and unquestionably the best since 1929 in respect to profits. The quota of new and difficult problems to face seemed a little smaller during 1936 than in most recent years, and a somewhat better balance existed between the different branches of the industry. 'Domestic consumption of gasoline in 1936, estimated at about 475 million barrels-the highest on record, was approximately 11 per cent above 1935, and 26 per cent above 1929. Demand for crude oil increased in about the same proportion: over 1935, and the average production, of about three million barrels daily,' constituted a new high level.

Jan 1, 1937

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists It Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfleld Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I-lath St. S. W. B'ham, Ala., Phone 56-5566 MILTON H. FIES Consulting Engineer Rooms 1201-2. Albama Power Co. Bldg. Birmingham, Alabama]

Jan 1, 1952

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922