Search Documents

By Peter T. Luckie, Harold L. Lovell, E. R. Palowitch, A. W. Deurbrouck, James K. Kindig

PART 1: DENSE MEDIUM SEPARATION by E. R. PALOWITCH and A. W. DEURBROUK INTRODUCTION During 1965, 64.9 percent of the 512 million tons of bituminous coal and lignite produced was cleaned mechanically, of which 95 million tons was cleaned by dense medium processes.l The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes rose from 7.0 to 28.5 percent from 1938 to 1965. Dense medium separations include those coal preparation processes which clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes offer the following advantages over other coal cleaning processes : 1. Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of the feed in the range of e 0.1 specific gravity units. 2. Ability to maintain a separating gravity that can be controlled with ±0.005 specific gravity units. 3. Ability to handle a wide range of sizes (up to 14 inches). 4. Relatively low capital and operating costs when considered in terms of high capacity and small space requirements. 5. Ability to change specific gravity of separation to meet varying market requirements. 6. Ability to handle fluctuations in feed both in terms of quantity and quality. HISTORY Sir Henry Bessemer patented the first dense medium process in 1858. Solutions of the chlorides of iron, manganese, barium and calcium were proposed as separating liquids; the separation was made in a cone-shaped separator. One large-scale plant using calcium chloride was erected in Germany but soon was abandoned. The Chance process, using a mixture of sand and water, was first

Jan 1, 1968

By J. R. Long, C. E. Armantrout, A. H. Roberson, T. R. Graham, R. S. Dean

THE general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing 10 to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heusler1 recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and io per cent Al but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 [ ] has drawn a hypothetical boundary for the alpha field with few data to support such construction. The binary systems involved have received considerable attention by numerous investigators, and their general features are well established. The hopper-aluminum system (Fig, I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smiths established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig. 2) has been recently reviewed by Dean and co-workers.7 Using high-purity alloys, they place the solubility of alpha man-

Jan 1, 1946

By Philip B. Bucky

[CONTENTS t. How Does One Determine WhetherPAGE an ore Body Will Block-cave?R. W. Hughes13 Sherman R. Burdick 13 PAGER. T. Gallagher 14 Mark A. Smith 2 C. F. B. Price, Jr.14 Harry A. Leidich2Benjamin F. Tillson 14 McHenry Mosier2C. F. Jackson14,17 R. W. Hughes2R. Taborelli15 Sherman R. Burdick3Frank A. Ayer16 R. T. Gallagher 3Philip B. Bucky16 Benjamin F. Tillson 3Rollin Farminr6 Lucien Eaton 3J. L. G. Weysser15, 0,17 C. F. Jackson 3George S. Rice17 Philip B. Bucky32. How Does One Determine the Block4. What Determines the Procedure in Dimensions and the DevelopmentRemoving Caved Ore? Work Necessary to Make an OreHarry A. Leidich17 Body Cave?McHenry Mosier17,21 Mark A. Smith 5,7,() R. W. Hughes17 Harry A. Leidich6Sherman R. Burdick 18 McHenry Mosier6,7,12 R. T. Gallagher 18 R. W. Hughes6Mark A. Smith I8 Sherman R. Burdick 7Philip B. Bucky20, 21, 23 R. T. Gallagher 7C. F. B. Price, Jr20 Benjamin F. Tillson 7,11R. H. Bennett21 L. E. Young7C. F. Jackson 21, 23 Robert D. Hoffman8, 1 2Gerald Sherman 3 . 21 Gerald Sherman8Tell Ertl21 Philip B. Bucky10, 11, 12G. K. Foster 23 R. S. McClellan 12C. H. Shoemaker23 Tell Ertl 12 3. How Do the Forces Act and What Are5. What Are the Criteria for Determining the Stresses Developed in a Blockthe Efficiency of a Block-caving That Cause It to Block-cave?Operation? Mark A. Smith 12, ISHarry A. Leidich23 Harry A. Leidich13McHenry Mosier24 McHenry Mosier13R. W. Hughes24 Sherman R. Burdick 24 R. T. Gallagher 24]

Jan 1, 1942

By T. R. Graham, R. G. Feustel, J. R. Long, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By Josef Intrater

A dilatometric determination of the a + ß region temperature limits was performed on vacuum melted Zircaloy-2. The temperature of transformation for a-a+ß and a+ß — ß on heating and cooling as a function of rate of heating and heat treating history was studied. The limits were found to be 815° to 830°C to 975° to 995°C on heating and from 960° to 930°C to 785° to 770°C on cooling. A 5° to 15°C increase was observed for a- a + ß with increased rate of heating and a 20° to 30°C decrease for ß - a + ß with increased rate of cooling. 1 HE transformation temperature for pure zirconium has been determined by many investigators1-5 using metallography, electrical resistivity measurements, and dilatometry. The effect of the rate of cooling on the transformation temperature of zirconium has been studied by Hayes and Kaufmann6 and Duwez,7 and the effect of alloying elements by pfei18 and McGeary.13 Since the development of Zircaloy-2, the limits of the a + ß region for that alloy have been also determined. The first reported temperature for the a — a + a transformation in Zircaloy-2 was 900°C and for a + ß - ß 1000C Subsequent studies by Picklesimer and damson" indicated the beginning of the transformation at 810°C, and the metallographic study by the Technology Group of the Special Materials Section at the Westinghouse Bettis plant1' suggested that 820°to 830°C is the temperature of transformation. The dilatometric investigation by the latter group yielded 830°C for the beginning of the transformation. Thomas and Forscher12 set the beginning of the transformation at 900 °C on heating and the end of the transformation at 870°C on cooling. The above investigators stated in their paper that the dilatometric curve exhibits features caused by a eutectoid reac-

Jan 1, 1962

By Francis Church Lincoln

I. Situation and Surroundings, The Promontorio mine is situated at the northern end of the Sierra San Francisco de Coneto, in the town of Promontorio, Partido of El Oro, State of Durango, Mexico. As shown in the sketch-map, Fig. 1, the nearest railroad station is Chin-acates on the Mexican International Railroad, 82 miles north of the city of Durango. The mine is 16 miles north of the sta-tion by air-line. It is reached by means of a good wagon-road which first crosses the Guatimapé Plain, passing the ranches of San Antonio and San Julian, to Estacion—a distance of about 15.5 miles—and then entering the mountains crosses the Sierra to Promontorio—a further distance of 11.5 miles— making in all a distance of 27 miles by road from railroad to mine. Promontorio is just beyond the summit of the range, at an elevation of about 8,000 ft. above sea-level, or 1,350 ft. above the Chinacates station. The Castillo de San Francisco, the highest peak in the Sierra, has an altitude of 10,000 ft., and the Promontorio road crosses the summit of the ridge at an elevation of 9,000 ft. by a pass just below this peak known as the Puerto del Almagre. The Promontorio mill is situated at Santa Inés, 2 miles by tram or 3 miles by wagon-road to the north of Promontorio and about 600 ft. lower. The Sierra San Francisco de Coneto decreases in height towards the north and west till it comes to an end at the Mel-chor Arroyo on the ranches of Melchor and Ramos. Beyond this arroyo another range, the Sierra de la Candela, begins. In the vicinity of the Promontorio mine the hills are very rugged and the surface is furrowed by ravines which contain running streams during the rainy season-—July, August and

Jan 1, 1908

By Werner Ostertag

A series of rare earth cobalt compounds of the composition RCoa (r = Ce, Pr, Nd, Sm, Gd, Tb, Dy, Ho, Ev, Tm, Lu) has been prepared. The compounds crystallize in space gvoup R3m and are isomorphous with PuNi3. Except for CeCo3 and PrCo, the series shows decreasing- values of a. and co. The relalively small parameters of CeCo, and PrCo, are explained by valencies of cerium or praseodymium which exceed the usual rare earth valency of three. The structure of the compounds is discussed as in-fillings of kagome nets in direct and staggered superposition. In the course of a systematic investigation of rare earth cobalt compounds"2 and their magnetic properties,, a series of alloys corresponding to the formula Rco3 has been prepared. The investigation of the Rco3 series was stimulated by our investigation of the yttrium cobalt system2 as well as by reports in the literature: Smith and Hansen4 reported the structure of YcO3 and Van vucht5 that of GdCo3; ceco3,6 Gdco3,7 and DyCo3 7 have been found to be single-phase during phase diagram studies. It was the purpose of this work to report crystallographic data on the entire Rco3 series and to interpret the structure of these compounds on the basis of general principles as discussed by Frank and Kasper.8 At the time this work was terminated, it was learned that a similar investigation has been carried out independently by Bertaut, Lemaire, and schweizer.9 Except for CeCo3 (ao = 4.952, co = 24.73') and NdCo3 (a0 = 5.067, co = 24.76') data of this work are in satisfactory agreement with their investigation. EXPERIMENTAL TECHNIQUES A series of samples having the composition Rc03 was prepared from stoichiometric amounts of the rare

Jan 1, 1968

By B. Tani, K. Anderson, I. Johnson, R. Schablaske

INVESTIGATION of the various rare earth-cadmium binary systems discloses the existence of a compound corresponding to the composition MCd6 in all systems save the La-Cd system. Lattice constants for all of the MCde compounds, except LaCd6 which apparently does not form, and PmCd6 whose synthesis was not attempted, are also recorded herein. Iandelli and Ferro 1 report the existence of the compound CeCd6. No additional information, structural details, and so forth are given. Elliott and Lemons2,3' have measured the vapor pressure of cadmium over CeCd6 and have calculated the activity of cadmium in solid CeCd6. These authors find that CeCd6 exists over a composition range from 5.967 to 6.098 (Cd:Ce ratio) at 584oC, and from 5.971 to 6.118 at 639°C. The following is an excerpt from the paper by Elliott and Lemons: 2 "Recently Mr. F. H. Ellinger of this laboratory has indexed an X-ray diffraction powder pattern of CeCd6.00 which we had prepared by gas phase reaction. The compound has a primitive cubic unit cell with a = 15.783 + 0.001A Based on the volume of the cubes surrounding an elemental cerium or an elemental cadmium atom, Mr. Ellinger finds room for 24.10 CeCd6 formula units in the CeCd6 unit cell; similar calculations based on CeCd2 and CeCd11 yield 24.18 formula units per unit cell. The presence of 24 CeCd6 units per unit cell seems probable with an X-ray density of 8.255 grams per cubic centimeter. The most one can say about in-terstitial~ is that there appears to be room in the crystal even at room temperature." Measurements of the solubility of the rare earths in liquid cadmium4 led to the discovery of GdCd6,

Jan 1, 1964

By C. P. Proctor, J. T. Crawford, John Griffen

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 184.1. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott 1 describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer, while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mill. (3/16 to 5/16-in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product used for boiler fuel or other purposes. The overflow of both troughs was joined to form the washed coal product.

Jan 1, 1950

By C. D. Dolman

SINCE the outbreak of the war we have discovered in the United States minerals of which there was no general knowledge, and which compared very favorably with anything that could be found in any foreign country. One of these was magnesite, or the carbonate of magnesium as it occurs in nature. This mineral crystallizes in the rhombohedral form, has a specific gravity of 3.00, molecular weight of 84 4, molecular volume of 28.1, and a hardness of 3.5 to 4.5.1 Had it not been for the development of the California deposits of this mineral and the discovery of immense new deposits in Stevens County, Wash., the production of steel during the war would have been more seriously handicapped than it was. Now, that the war is over, we face the possibility of competition' with the cheap Austro-Hungarian magnesite; and while that may not he so cheap as it was before the war, adequate protection should be given the producers in this country to insure the full development of our own resources. The consumption of magnesite in the United States in 1913, the year preceding the war, was 172,591 tons of calcined and 22,872 tons of crude magnesite. Less than 3 per cent. of this amount was produced at home. At the present time, practically all of the magnesite used in the United States is produced at home. Expensive plants have been constructed, extensive exploration work done, and production pushed to the utmost to supply the necessary requirements of the war. Thus a considerable industry has been built up within our borders. Some magnesite has been imported from Canada and Mexico, but the Canadian ore was of an inferior grade and could not be used satisfactorily. During the year 1918, production decreased in both the United States and Canada; the production in the United States was 225,000 tons in 1918 as against 315,000 in 1917, and in Canada 39,365 tons in 1918 as against 58,090 in 1917.

Jan 8, 1919

By O. S. True, C. H. Herty

It is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open-hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCancel states that such is not the case. The experimental work was carried out to confirm the results of Roh12 as to the reversibility of the reaction. Six trials are herein considered. In each 200 gm. of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent, of sulfur in each. In runs 5, 6 and 7, metallic manganese and iron sulfide to give the same proportions of. manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots. The results of these melts are as follows: Ingredients of Charge Analysis or InRot ManOaneBe, SulfUR, ManOaneBe. SULFUR, Run Material Charged PeR Cent. PeR Cent. Per Cent. PeR Cent. 2 MnS + Mn............... 1.0 0.452 0.636 0.367 3 MnS + Mn............... 2.0 0.50 1.57 0.310 4 MnS + Mn............... 4.0 0.50 2.81 0.230 5 FeS + Mn................ 1.0 0.50 0.647 0.397 6 FeS + Mn................ 2.0 0.50 1.45 0.374 7 FeS + Mn................ 4.0 0.50 2.73 0.195

Jan 1, 1925

By J. B. Austin, H. H. Pierce

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By H. H. Pierce, J. B. Austin

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By William E. Ford, Edward Salisbury Dana

A. Hexagonal Division 1. Normal Class (13) Beryl Type 2. Hemimorphic Class (14) Zincite Type 3. Pyramidal Class (15) Apatite Type 4. Pyramidal-Hemimorphic Class (16) Nephelite Type 5. Trapezohedral Class (17) B. Trigonal or Rhombohedral Division 1. Trigonal Class (18) Benitoite Type 2. Rhombohedral Class (19) Calcite Type 3. Rhombohedral-Hemimorphic Class (20) Tourmaline Type 4. Trirhombohedral Class (21) Phenacite Type 5. Trapezohedral Class (22) Quartz Type 6. Other Classes (23) 7. Other Classes (24) Mathematical Relations of the Hexagonal System 119. The HEXAGONAL SYSTEM includes all the forms which are referred to four axes, three equal horizontal axes in a common plane intersecting at angles of 60") and a fourth, vertical axis, at right angles to them. Two sections are here included, each embracing a number of distinct classes related among themselves. They are called the Hexagonal Division and the Trigonal (or Rhombohedral) Division. The symmetry of the former, about the vertical axis, belongs to the hexagonal type, that of the latter to the trigonal type. Miller (1852) referred all the forms of the hexagonal system to three equal axes parallel to the faces of the fundamental rhombohedron, and hence intersecting at equal angles, not 90". This method (further explained in Art. 169) had the disadvantage of failing to bring out the relationship between the normal hexagonal and tetragonal types, both characterized by a principal axis of symmetry, which (on the system adopted in this book) is the vertical crystallo raphic axis. It further gave different symbols to faces which are crystallographally identical. It is more natural to employ the three rhombohedra1 axes for tri- gonal forms only, as done by Groth (1905), who includes these groups in a Trigonal Syslem; but this also has some disadvantages. The indices commonly used in describing hexagonal forms are known as the Miller-Bravais indices, since the were adopted by Bravais for use with the four axes from the scheme used by Miller in the other crystal systems.

Jan 1, 1922

THE story of Miami really is two stories. First, that of an excellent Porphyry Copper mine, ably managed as a business enterprise, and always among the leaders in technical progress. Concentrating its first ore in 1911, it had by 1925 paid dividends totaling $30,000,000 or $40 per share on stock that had cost the public $5 per share in March, 1908. The ore, containing 2.5 per cent copper at the start, had become progressively leaner but the recovery had tended to improve. Production costs had gone up during the World War and the early post-war period; and had come down again. In all these respects it had followed the norm. If the mine had been abandoned as exhausted and the company had been liquidated late in 1925 (a program that had been given earnest consideration in 1924), Miami would have gone down into history a first-rate mining venture; as an active and progressive participant in the great Porphyry achievement. But Miami was not liquidated in 1925; instead it started to write the record of its second and really amazing story. Near the old mine was a large body of low-grade ore containing, in place, less than 20 lb. of copper to the ton, and without, incident- ally, any considerable sweetening of gold and silver. Any method of underground mining that was cheap enough would certainly entail some dilution, so that ore as sent to the concentrator necessarily would average much less than 20 lb. As a matter of record, the average for 1929 was 16.6 lb., from which 11.726 lb. was recovered as concentrate. As already said, the exhaustion of the older orebody during 1925 was foreseen; but in 1924 the decision was reached to enlarge the concentrator and develop a new mine. An expenditure of $2,500,000 was entailed in this program. By October, 1925, the

Jan 1, 1933

By W. L. McMorris

The Convertol process was first described in Germany by Muschenborn' in 1952. In the U. S. Fraser' reported this new process in 1953, and Brisse and McMorris" presented the results of a Convertol pilot plant at the Alpheus preparation plant in Gary, W. Va., illustrating the mechanics of the process by a series of sketches. The purpose of the present investigation was threefold: 1) to determine the relative effectiveness of various oils and hydrocarbons for recovering coal by the Convertol process, 2) to ascertain the behavior of coal pulps in this process under various operational conditions, and 3) to compare Convertol with flotation in the recovery of fine coals. APPARATUS, PROCEDURE, AND COAL SAMPLES In laboratory work with the Convertol process a Waring Blender equipped with a speed-regulating rheostat was used for wetting, conditioning, inversion, and retention of the coal pulp. A 5-in. International centrifuge was adapted to dewater the agglomerated clean coal product by installation of a 100-mesh screen inside the regular bronze basket of the centrifuge. Except where otherwise stated, the Convertol testing was performed by the following steps: 1) A 450 to 500-cc coal slurry, containing 24 pct by weight of solids, was agitated in the blender for 10 min at 100 rpm to insure complete wetting and mixing. 2) Eight percent by weight of oil was added to the coal slurry in the blender and agitated for 1 min at 11,000 rpm to result in the phase inversion or agglomeration of oil-coated coal particles. 3) The agglomerated coal slurry was poured onto a 100-mesh sieve and wet-screened for about 2 min to remove most of the ash and some of the water. 4) The material remaining on the screen was transferred into the centrifuge for final dewatering. 5) A portion of the clean coal was immediately weighed out for moisture determination, while the

Jan 1, 1960

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By B. B. Zavoico, J. G. H. Crump, P. P. Gregory

West Texas was the scene of greatly increased oil activity during 1937, producing 75,743,000 bb1.l in that year as compared with 61,901,-000 bb1.2 in 1936, an increase of 22.36 per cent. The annual total of wells completed increased from 15863 in 1936 to 28062 in 1937, an increase of 76.92 per cent. Of the total completions in 1937, 2464 were oil wells,2 11 gas wells2 and 331 dry holes.2 The marked increase in the number of oil wells completed in West Texas during 1937 had a substantial effect upon the daily average production per well, which decreased 20.84 per cent from December 1936, when a total of 5310 wells3 produced 5,236,467 bbl.3 for an average of 31.81 bbl. per well per day to December 1937, when 7571 wells2 with a total production of 5,910,257 bb1.2 averaged 25.18 bbl. per well per day. Drilling blocks and checkerboard acreage were being acquired following geophysical work in the northern end of the Permian Basin area, composed of Bailey, Cochran, Hockley, Yoakum and Terry Counties, presaging extension of active development northward. During 1937, at one time 30 geophysical crews were working in West Texas, and an average of 15 to 20 crews was active in this area throughout the year. Discoveries Wasson-Denver Field.—Wasson-Denver field in Gaines and Yoakum Counties was the outstanding field discovery of the year. Production is from porous limestone found at about 5000 ft., and an average well is good for from 300 to 500 bbl. of crude oil per day through 3/4-in. choke. The discovery well was drilled by A. G. Carter and others on the Wasson Ranch, Gaines County, and the field has since been extended into Yoakum County. At the year's end 21 wells had been completed, producing

Jan 1, 1938