Search Documents

By D Craw

Uplift of the antiformal ranges in Central Otago, New Zealand , has resulted in the progressive evolution of eluvial placer deposits in tectonic sediments on the range flanks and along their margins. The placers are derived from the reworking of fine-grained gold from the auriferous Manuherikia Group fluvial sediments which covered the basement prior to uplift of the ranges. Gold in the tectonic sediments at Matakanui shows a progressive increase in grainsize in successively younger sediments and nuggets in the youngest gravel sequence are up to two orders of magnitude larger than gold grains in the parent alluvial source. Most of the gold in the tectonic sediments is highly irregular in shape, commonly with delicate surface textures which could not have survived fluvial transport and are indicative of authigenic precipitation. Some coarse grains have been rounded by recycling, and further addition of authigenic gold has occurred. Placer gold values result from both physical and chemical enrichment during sedimentary recycling. Continued range uplift and back-thrusting of sediments on to the ranges results in recycling of earlier formed placer sediments. They also result in further enrichment of gold values through the incorporation of additional supplies of the parent alluvial source sediment The host sediments are widespread along the ranges and are not confined to sites of historic mining activity.

Jan 1, 1992

By K F. Tang, J-W Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Xiong’ershan district in the southern margin of the North China Craton (NCC) contains more than 20 gold deposits hosted in the late Neoarchean to early Palaeoproterozoic amphibolite facies metamorphic rocks or late Palaeoproterozoic unmetamorphosed volcanic rocks. Gold mineralisation consists mainly of auriferous quartz veins and disseminated ores in hydrothermally altered zones, with additional gold mineralised breccia pipes. Gold orebodies are strictly controlled by secondary- or higher-order brittle/ductile-brittle faults. Isotopic dating reveals two separate episodes of gold mineralisation: the Shanggong and Dianfang deposits formed in the range of 236 ± 1.4 to 202 ± 18 Ma, whereas the Gongyu, Qianhe and Qiyugou deposits formed between 135.0 ± 0.5 Ma and 124.0 ± 1.0 Ma. Stable isotope and noble gas geochemistry studies indicate that the Triassic gold deposits were precipitated from deeply-sourced, low-salinity fluids at 250–350°C, but whether the fluids were mainly derived from metamorphic devolatilisation or magmatic degassing remains unresolved. In contrast, the Early Cretaceous deposits most likely precipitated from a dominantly magmatic fluid, although metamorphic and meteoric components cannot be ruled out. Results from this study, when combined with regional geological and geochemical data, suggest that the Triassic gold mineralisation was generated by the deformation associated with the collision between the North China and Yangtze cratons, forming the Qinling-Dabie orogen. In contrast, the Early Cretaceous gold veining was a result of lithospheric destruction of the NCC, a process initiated by plate subduction from both the south and north since late Palaeozoic but ultimately triggered by the westward subduction of the palaeo-Pacific plate in the late Mesozoic. This study helps to reconcile the long-term debate on the timing, genesis and geodynamic setting of gold mineralisation in the Xiong’ershan and other districts along the southern margin of the NCC.CITATION:Li, J-W and Tang, K F, 2015. Gold deposits in the Xiong’ershan District, Southern North China Craton – products of Triassic deformation and Cretaceous craton destruction, in Proceedings PACRIM 2015 Congress, pp 341–344 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By B E. Hall, D B. Kahler

"'Optimisation' has become a catchcry among many mining companies looking to tell the market how mining businesses will be improved and shareholder value increased. Consequently, the term 'optimisation' has been adopted by many service providers as they look to assist mining companies in achieving their objectives. But the explosion of services and products being offered with the label 'optimisation' has created some confusion. Mining companies ask for help in 'optimising' and service providers offer their assistance because they have a product that has the word 'optimisation' in its title. This is of course an over-simplification, but not by much! The authors' discussions in recent years with both mining companies and service providers have uncovered a number of very different definitions of optimisation.This paper provides a framework for identifying the scope and approach of different mining optimisation products and services, particularly the distinction between optimisation of components of the operation and the business as a whole. The different types of business optimisation are discussed, highlighting the failings of the mining industry's typical approach of strategy selection (as opposed to strategy optimisation). Mining business optimisation is discussed as a wicked problem, with the implication of this on how strategy optimisation models should be used and what the objectives of a business optimisation study should be.Case studies are also included to illustrate how fully flexible strategy optimisation models have been applied to assist decision-makers understand the impacts of changes in one part of the operation on the whole mining and treatment process, from geological models to the sale of product to customers.CITATION:Kahler, D B and Hall, B E, 2016. Strategic decision-making in mining – business optimisation using flexible evaluation models, in Proceedings Project Evaluation 2016, pp 215–225 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By T P. Fischer, S N. Williams, N C. Sturchio

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these 'primary' components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

By F F. Pitard, K J. Ehrig

The Olympic Dam iron-oxide copper-gold (IOCG) uranium-silver deposit is second in size only to Norilsk, the gigantic metalliferous deposit. Olympic Dam is the largest publicly declared uranium, fifth largest copper and third largest gold resource. The deposit is typified by texturally destructive brecciation and intense iron metasomatism of the Roxby Downs Granite, bedded clastic facies rocks and mafic-ultramafic dykes. The deposit contains over 100 minerals. Copper mineralisation consists of chalcopyrite, bornite and chalcocite. Uraninite, coffinite and brannerite are the dominant uranium-bearing minerals. Gold mineralisation consists of electrum, tellurides and Au-Cu alloys. Hessite is the major silver-bearing mineral. The economic minerals are disseminated throughout the breccia matrix where the average grain sizes of the Cu-sulfide, uranium, gold and silver minerals are ~50, 20, <5, <5 microns, respectively.A significant number of sampling theory-based test programs have been completed since the mid-1990s to establish sampling nomographs, select appropriate sampling (ie split versus chip and interval lengths) and sample preparation protocols, quantify the errors associated with each subsampling stage, determine the practical uncertainty limits of Olympic Dam matrix-matched standards, and identify improvement opportunities related to the ongoing assaying quality assurance / quality control (QA/QC) program. Invaluable knowledge and unexpected insights gained from sampling studies at Olympic Dam have helped to improve our understanding of the distribution of economic and deleterious elements within the Olympic Dam deposit.CITATION:Ehrig, K J and Pitard, F F, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Eighth World Conference on Sampling and Blending , pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Radio Detection and Ranging is an active form of remote sensing. The-imaging system sends out a source of electromagnetic energy to 'illuminate' the terrain and then records the energy returned. The wavelengths used by radar are in the microwave region and vary from a few millimetres to about a metre. Radar systems are independent of lighting conditions and weather. In addition, targets may be illuminated in the optimum direction to enhance features of interest. New Zealand was one of the principal investigators on the Shuttle Imaging Radar (SIR-B) experiment, part of the payload on Challenger Mission 41-G in October 1984. Data collected over New Zealand was restricted to two very poor quality optical images and one poor quality digital data take. The digital image covered the ranges between the Hawke Bay-Wairoa Basin and the Volcanic Plateau. Variations of texture in this image frequently were indicative of variations in lithology and induration. The image also clearly depicted major faults where these had had a significant effect on the topography.

Jan 1, 1986

At the treatment plant of the Broken Hill South Limited, Broken Hill, the zinc concentrates, with water, are pumped out to a more or less level area, and stored in dams to dry by drainage and evaporation.In-the construction of these dams a clay bank is first thrown up around the proposed dam site. The concentrate and water mixture are then run in from the perimeter, the solids being continuously shovelled up to increase the bank height, while the clear water is drained off at the centre and returned to the treatment plant.These dams vary in size up to 57,000 sq. ft. in area; when completed the banks are about 12 it. high, and the capacity for the largest dams is about 350,000 cub. ft., say, 20,000 tons.The survey office is called upon for a monthly survey of these dams, generally three of which are in process of building or refilling. The puggy nature of the material prohibits walking beyond the bank of the dam, therefore the following method of estimating concentrates was evolved. No originality is claimed, but as the need is for a true survey, and the results have shown the accuracy of the method, a description is warranted. The dam site is first laid out into 10-ft. squares with a theodoliteand 150-ft. steel tape, the outside lines being placed about 15 ft. from the clay bank - 15 ft. is the maximum convenient distance from the bank for working with the levelling staff mentioned later.As the dam is rarely rectangular in plan, the outside points pegged out are not always the corner of a square, but are placed to give the greatest convenience in later work, that is to say, there may be triangles and irregular figures. The plan (Fig. 1) and photographs (Figs. 5 and 6) will give the general idea of the layout. At each point is driven a 3 ft. 6 in. round iron peg about 3 ft. into the ground. This peg is to permanently mark the point, and is not liable to be...

Jan 1, 1925

By Stitt P. H

In Australia, the term "heavy mineral deposits" is used to denote sands which contain variable but economic quantities of the minerals rutile, ilmenite and zircon, often with minor amounts of monazite and xenotime as co-products. Australia has been a significant producer of rutile, ilmenite and zircon from such sands for fifty years and has long been the leading producer of rutile and zircon. The industry had its beginnings with the mining of present day beaches in northern NSW in 1934. Early work was small scale and in some cases involved hand winning of naturally concen- trated mineral for direct export. During World War II and immediately after the industry became increasingly mechanised and by the 1970s on the east coast operated between Newcastle, NSW north to Fraser Island in Queensland. Deposits worked included present day beaches, fossil strand lines up to 5 km or more inland from the present coast and aeolian concentrations. In the mid 1950s, operations commenced on the west coast of WA, south of Perth. Western Australian mineral sands tend to be rich in ilmenite as compared to the east coast. However the WA ilmenites are lower in chrome oxide and make a better syn- thetic rutile feedstock.

Jan 1, 1988

As part or a programme to raise lead smelter capacity from 65.000 to 140.000 tons bullion per annum. one new 1000 sq. ft. updraught area sintering machine replaced eight small downdraught machines.The metallurgical specifications were based on and laboratory tests at Mount Isa. Existing practice filtering concentrate as part of the charge preparation system and discharging wet filter cake to mixing was retained. This dictated a hot return fines circuit to maintain the required feed moisture content at low return sinter ratios.The engineering specifications provided for cenlralized control of plant and process, minimum operating labour, high plant availabi;lity and highest standardsof hygeine. Crushing and conveying capacity was set to cater for the most optimistic level of sintering capacity.On start-up a number of major engineering and hygiene problems became apparent, in addition to normal teething troubles. These problems have largely been overcome and reliable operation. at less than optimum production rate is now being achieved.

Jan 1, 1968

By Madgwick J. C

Four manganese dioxide leaching microorganisms, an Achromobacter spp, Aspergillus niger, Elllerobacter cloacae and Elllerobacter agglomerails were purified from sucrose enriched crude mixed cultures which contained at least sixteen, non-leaching, morphologically different, colony types. Fastest leaching rates were obtained from the original enrichment's mixed cultures (1.26 g Mn++ I/d) while best yields of Mn++ m terms of sugar use came from Achromobacter and A. niger being 0.84 and 0.89 g Mn++/g sucrose respectively. The peak efficiency in manganese reduced, per carbohydrate used, coincided with the exponential growth phase for Achromobacter. The two Elllerobacter species performed better in stationary or senescent growth phases.

Jan 1, 1985

By M Wimmer

LKAB operates two underground iron ore mines located in the northern part of Sweden, both using sublevel caving (SLC) as the mining method. Knowledge of the mechanisms of gravity flow is important since it affects both ore recovery and waste dilution. This paper describes results from a large-scale field test carried out at the Kiruna mine with a focus on gravity flow. It is part of Work Package 2 in the I2Mine project financed by the EU. A total of ten rings were blasted. Smart Markers based on radio frequency identification technology were used to monitor the gravity flow. An accurate delineation of the isolated extraction zone requires reliable detection of all recovered Smart Markers and precise knowledge of the 3D position of the markers within the burden. It was therefore necessary to carry out borehole deviation measurements (collar, alignment and trajectory). The blast performance was monitored by high-speed filming, near-field vibration monitoring and velocity of detonation measurements. Three-dimensional stereo images were taken from the drawpoint and the loaded bucket after each mucking cycle. Based upon that, fragmentation was assessed both in 2D and 3D. Furthermore, volumetric differences were determined at the drawpoint, which reflects the mobility of loaded material. For draw control, the Fe content is estimated by measuring weight and assuming a full bucket. The measured volume of rock in each bucket further improves this estimate. Possible flow disturbances occurring at the drawpoint were revealed by video recording. Two-dimensional laser scanning was carried out during mucking to track the position of the bucket and estimate the position and slope of the muck pile.The results from this test clearly show that the gravity flow in the large-scale sublevel cave in Kiruna mine is often of disturbed character. Standard draw occurred only in three rings and shallow draw in the remaining seven rings. In five cases, shallow draw developed towards standard draw, but occurred at rather late stages during extraction (70–125 per cent). The maximum width of the draw varied between 10 m and 13 m except for one ring (6 m). The draw reaches the cave rather early (5–25 per cent extraction) in shallow draw situations and much later (about 50 per cent) during standard draw. Waste originates from above in most cases, while more significant portions often occur at about 20–45 per cent extraction.All the results from this extensive field test are not yet fully analysed, and further field tests are planned. A more detailed insight into gravity flow in large-scale SLC and possible influence by drilling, blasting and the mucking procedure is expected in the future.CITATION:Nordqvist, A and Wimmer, M, 2016. Holistic approach to study gravity flow at the Kiruna sublevel caving mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 401–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

The morphological changes that gold undergoes during transport in gravel-bed rivers are a function of transport distance in particular, as well as bedload material, river gradient and velocity, and bed roughness. Gold size, shape and outline are modified by abrasion, flattening, folding and breakage during transport. The resultant morphological characteristics can be used to predict source types, source location and transport distance, as well as the origin and dispersal patterns of gold in ancient placers where the transport history is unknown.

Jan 1, 1998

Magnetite cenospheres 40-270 I/m in diameter have been found during the combustion of pyrite concentrate.Micrographs of the surface and internal structures are presented together with comment on the mechanism of forrnation.The similarity to cenospheres found during the combustion of pulverized fuel was noted and speculation raised to their contribution to the dust and fume load in flash smelters.

Jan 1, 1980

The Martha Hill project operates with a nett surplus of water, due to the catchment of rainwater on the tailings dam and the requirement to de-water the open pit mine. It is necessary to discharge this surplus, treated as required, to the Ohinemuri River which flows past the process plant.   The treatment plant, adjacent to the process plant, handles all effluent from the Martha Hill operation including water pumped from the mine, excess water from the tailings decant, and seepage from the tailings dam underdrains. To-date the plant has treated and discharged over 800 000 tonnes of water.

Jan 1, 1991

A comprehensive analysis of rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging: interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcore is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure. Both solution types rely on constant orientations (orientational stability) of the selected structure, but the internal solution actually provides its own test of orientational stability. External solutions are the norm in outcropping situations and internal solutions are invaluable in blind situations. In blind situations sequential "internal then external" solutions can be used respectively to provide a reference structure and then use this for subsequent external solutions at individual points downhole. Blind prospects can now be drilled and interpreted as easily as outcropping prospects. Each solution type has its own optimum requirements. External solutions are ambiguous for certain orientational relationships between the drillhole and the reference structure (for example, a perpendicular relationship), hence drillholes in which external solutions are planned should be designed to avoid these orientations. Internal solutions are ambiguous for straight drill paths, and are most unambiguously resolved when the drill path attains maximum drillhole dimensionality, that is, it occupies a wide variety of orientations in 3D space; hence drillholes in which internal solutions are planned should be designed as combinations of non-parallel holes or as individual strongly curved holes. For both solution types an understanding of the kind of structural fertility required leads to intelligent design of drill paths, which is termed structural drill targeting. It is distinct from spatial drill targeting, which is the process which defines and (x,y,z) point-or volume-target. Effective design of drilling programs requires both structural and spatial targeting. The external and internal solutions for vectorial parameters are implemented via (1) visual (qualitative), (2) stereographic, or (3) core orienting frame procedures. Each of these has its own advantages. Stereographic procedures have been simplified via the erection of a drillcore reference frame in which three fundamental angles are defined, and the formulation of an all-inclusive set of stereographic recipes for determining orientations from the measurement of these angles. Non- vectorial structural parameters comprise an ad hoc array of useful measures which are simply described by numbers. Examples are angles between structures, and density of structures. Such parameters (some of which provide useful vectors toward ore bodies) are invaluable in drillcore because they can be measured and recorded rapidly, without determining the orientation of the core. In a summary, non-oriented drillcore can now be structurally mapped exactly as if it were outcrop. Interpretation of the significant volume of unique structural information which is beginning to flow from this system can be optimised by using, in addition to the conventional cross section and longditudinal section, three new modes of presentation. The natural cross section is that section in space normal to a principal structure of interest. It is a section in which it is advisable to drill to obtain certain structural information, and in which the results need to be presented. A newly defined unique cross sectional orientational symbol is recommended for dramatic improvement in the quality of information presented in cross sections. Stacked level maps are a powerful adjunct to cross sections.

Jan 1, 1990

By J J. Robinson, B N. Noller, D M. Franks, G McIlveen, D R. Mulligan, A T. Soro

Fiji is a developing nation that relies on economic opportunities and recently experienced increased interest in mining and mineral exploration that could potentially benefit the country. In order to understand the lack of, or failure of, past rehabilitation activity, this study applied risk-based approaches to identify the significance of activities or actions applicable to rehabilitation of post-mined land in Fiji. This involved the use of qualitative, semi-quantitative and quantitative risk methodologies, which allow assessment and evaluation of mechanisms of mining administration and practices, as well as rehabilitation methods and approaches that have been applied successfully to post-mined land in other countries with similar environmental and climatic conditions and social and regulatory environments to Fiji. The semi-quantitative risk-based technique followed an earlier approach applied for mine closure by Laurence (2006) and provided a systematic way to assess and evaluate rehabilitation issues that were identified on-site by assessors, who were able to estimate through expert judgement the likelihood and consequences based on conditions, situations observed and circumstances on-site. It demonstrated that experienced professionals could reproducibly score likelihood and consequence of selected items relevant to mine site rehabilitation, despite the wide-ranging issues identified during post mined land rehabilitation. The quantitative risk-based approach was adopted as a method to determine environmental bonds for mining projects using the assessment of consequences and likelihood results from the semi-quantitative approach, then incorporating unit cost of materials or activities for local conditions required to fully rehabilitate each issue at net present value. Application to both an abandoned mine site and a newly opened mine site in Fiji showed that this approach could provide a risk-based estimate for rehabilitation cost and demonstrated potential applicable in the Fijian context.CITATION:Soro, A T, Mulligan, D R, McIlveen, G, Franks, D M, Robinson, J J and Noller, B N, ?2014. Risk-based Rehabilitation Strategies for Post-mined Land in Fiji, in Proceedings Life-of-Mine 2014 , pp 165–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By R J. Merchant

The Hauraki goldfield is located east of Auckland in the North Island of New Zealand. It includes Great Barrier Island, the Coromandel Peninsula and the Coromandel and Kaimai Ranges as far south as the town of Te Aroha and south east to Te Puke. It has a total north-south extent of about 180 km and an area of 3000 km2. The goldfield is the most productive in New Zealand, and while production at present is negligible, the area has undergone continuous exploration over the last seven years.

Jan 1, 1984

By R J. Mills, B S. Sinclair, D A. Fergusson, A G. Goldstone

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. The consenting of major mine site activities has historically required wide consultation and involves notification of the application.   The risk and cost associated with consultation can be significantly reduced via a non-notified process. A non-notified consenting process necessitates environmental effects to be shown to be æless than minorÆ, which requires the combination of robust science and a pragmatic approach to design, assessment of environmental effects, and consenting issues.   Key issues examined included consideration of how to practically operate a significant disposal project within the confines of an operating mine, minimising the costs, civil and geotechnical design and practical issues associated with traditional disposal. Environmental issues specifically related to the coal ash, led to a site specific performance driven approach to management rather than relying on conventional prescriptive approaches. Environmental issues of concern include the leaching of boron and aluminium from ash into groundwater and mine water management systems where both boron and aluminium can occur at elevated levels.   Coal ash exhibits unusual geochemical characteristics reflecting the primary coal composition and the combustion process. The dominant coal type combusted at the Huntly Power Station is derived from Rotowaro and the resulting ash is cementitious and has a high alkalinity. As a result the disposal design is based on the characteristics of the ash itself rather than the material into, or onto which the ash is disposed. Non-notified status was able to be achieved through consideration of these key characteristics of the ash, ensuring that the dimensions of the disposal site and each location was designed to minimise the flow of groundwater through the ash and demonstrating that the physical ash disposal effects are less than minor compared to the consented mining operation.

Jan 1, 2006

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997