Search Documents

By P Kirsch, P Jagals, D Viswanathan, J Shandro, R LaBouchardiere

The planning, design and operation of mines must include the development of positive environmental, community and land-use benefits if it is to achieve good corporate social responsibility and minimise detrimental impacts throughout the life of the mine. Life-of-mine (LOM) planning should, therefore, consider conducting mining activities in the best socially, environmentally and economically acceptable manner, from the commencement of exploration to post-closure of the mine. Current knowledge of LOM activities in relation to public health (life-of-community, or LOC) impacts neither fully captures the full suite of human health and well-being impacts, nor comprehensively informs society on these issues. This knowledge gap is becoming more apparent as public antipathy is increasing towards mining activities within Australia, Canada and globally. The purpose of this paper is to present preliminary and informative results of a literature review to gain insight into the extent of available public health and well-being knowledge associated with mining development. LOM development must also benefit the LOC, in that it must aim to minimise detrimental impacts, and maximise beneficial (including health) impacts on all associated communities. Health planning and programing for mitigation of potential adverse health impacts of mining should extend beyond the scope of work-related injury and illness (resulting from chronic exposure to harmful substances, infectious and lifestyle illnesses), to the health and well-being of workersÆ families and extended associated communities. By mapping the available but rather scarce literature on LOC areas to recognised LOM stages, this review found shortcomings and imbalances regarding research reporting on mining and its health-related impacts in the worker-to-community continuum.CITATION:Kirsch, P, Viswanathan, D, LaBouchardiere, R, Shandro, J and Jagals, P, 2012. Health impacts extend from the life of a mine to the life of a community - Knowledge gaps, in Proceedings Life-of-Mine 2012 , pp 161-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By N J. Welham

The Intec Copper Process is an environmentally advantageous hydrometallurgical process for the production of high purity copper and associated precious metals from copper sulphide concentrates. The process uses a mixed chloride-bromide lixiviant in an elegant cyclic circuit to leach the copper into solution, rejecting the iron as stable hematite rather than as unstable jarosite. After purification of the pregnant liquor, copper is electrowon at London Metal Exchange Grade A purity, while the anodic energy of the cell is stored as the soluble species, HalexTM, for recycle as the regenerated lixiviant to the leach circuit. Both gold and silver are leached and recovered directly from this cyclic process without resorting to cyanide leaching of the residue. No liquid emissions result from the Intec Copper Process, whilst spent air and water vapour from the leach are released to the atmosphere. The sulphur in the minerals reports to the solids residue in elemental form, without the need for expensive handling of voluminous gaseous sulphur dioxide streams found in smelters. A significant difference to competing smelting and hydrometallurgical processes is that any mercury entering the process from the sulphide concentrate feed is recovered rather than reporting directly to waste or polluting the environment. Outside the process circuit itself, the Intec Copper Process has several notable environmental advantages over competing technologies: Flexibility of scale with low capital and operating costs allow operation directly at the mill head at production rates as low as 15 000 tpa, significantly reducing environmental impacts from concentrates transport. The ability to handle low-grade and dirty concentrates often allows greater recoveries in the mill, improving both the economics and environmental acceptability of a mine by reducing metal losses to tailings. A comparison of the total energy requirements of the Intec Copper Process with those of competing technologies shows that the Intec Copper Process has the lowest energy consumption of any of the known hydrometallurgical processes, as well as improving upon pyrometallurgy under appropriate conditions.

Jan 1, 2002

By J Li

Cannington Mine has been developing through paste backfilled stopes since the year 2000. These paste drives have been used as either production drill accesses or long-term bypasses. Prior to this study, the ground support requirements for each paste development cut were: an initial 50 mm layer of fibrecrete, weld mesh bolted with 2.4 m split sets, followed by a second coat of 50 mm fibrecrete. Both layers of fibrecrete and the layer of mesh were to be installed before the next cut could be bored and fired. This support regime proved successful at Cannington, however, the total cycle time for each cut was lengthy due to the installation and curing times associated with each layer of surface support. In an effort to reduce the cycle time a study was carried out, with the aid of RocScience’s Phase2 numerical modelling software. The modelling reviewed all of the parameters controlling the stability of a newly excavated development cut. The parameters studied included the early strength of fibrecrete, the ground support load capacity, and the strength of the paste fill masses which varies depending on the cement content. As a result of the study, the ground support standard was revised. The revision has significantly decreased the cycle time as well as fibrecrete consumption, all the while maintaining the safety of personnel and equipment.

Mar 21, 2011

By Mitchell M. A

The steeply dipping Mammoth orebody is mined by Gunpowder Copper Limited using a sub- level uphole bench stoping method at a mining rate of 350 000 tonnes per year. of three per cent copper ore. Access to the mine, is provided by 1 in 9 decline which spirals in the footwall connect-, ing all the sublevels, thus maximising mobility and accessibility of trackless mining equipment Sublevels are driven in ore off cross- cuts from the decline every 15 metres vertic- ally. Sublevel drives are stripped out to widths up to 18 metres before cutoff slots are mined at each end. A two boom fan drilling jumbo is used to drill inclined rows of holes to the floor of the sublevel above. Two or three rows are fired at a time which allows broken ore and remnants from the level above to be mucked out by rubber tyred LHD equipment to the brow. Ore widths of up to 80 metres are en- countered at lower levels where ring drilling from longitudinal drill drives will break ore to a draw point system below. Development is carried out with three boom rubber tyred jumbos. All haulage from the mine is in 20 and 35 tonne rear dump trucks. All aspects of the mining operation are discussed including ventilation, pumping and drainage, services and future planning.

Jan 1, 1974

By S Hapugoda, J R. Manuel, M P. Ma, L Lu

Iron ore sinter quality depends heavily on the mineralogy, textures and physical structure of the sinter, which is formed upon solidification of the primary sinter melt. The interactions of the initial sinter melt with its surrounding materials will impact on the properties of the primary sinter melt and consequently the solidified structure of the sinter. By using a high-temperature visualisation system, in situ studies have been conducted on the effects of melt compositions (Al2O3, SiO2 and MgO) on the interfacial phenomena of the sinter melt on a natural iron ore substrate. It was found that the melt composition significantly influenced the wettability between the sinter melt and the iron ore substrate. The interactions between the sinter melt and the natural iron ore substrate were also examined. Such interactions can lead to further changes of sinter melt composition and hence the sinter melt properties that, in turn, further affect the wetting behaviour of the sinter melt.CITATION:Ma, M P, Lu, L, Hapugoda, S and Manuel, J R, 2013. Effects of melt composition on the interactions of sinter melt on a natural iron ore substrate, in Proceedings Iron Ore 2013 , pp 431-440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By L Lorenzen, H Muller, L Bernard

Australian companies and consultants are becoming ever more involved in projects in African, South American, East European and Middle Eastern countries. However, significant differences in culture and approach to projects sometimes make these projects challenging for reasons that are not purely technical. Often the challenges are rather related to how the project owner and local authorities perceive the reality. These perceptions and sometimes unrealistic expectations regarding project costs and potential outcomes need to be addressed by the æWesternÆ project developer and consultant.This paper will discuss the specific experience of Snowden in studies commissioned by companies from such countries for the development of very large, low-grade gold deposits in some of the most inhospitable areas in the world. The paper will further review similar projects undertaken in other ænew worldÆ countries and compare these to the initial Snowden experience.As the process operating costs of operations in many of these countries are extremely competitive when compared to the typical Australian operating costs, the paper will review the operating costs and the factors which may be pertinent to a large project of this nature, both in the Australian and the ænew worldÆ context. Will Australian-based operations be able to compete in the global gold market when the gold price softens again, as it will do at some stage in the possibly not-so-distant future?CITATION:Muller, H, Lorenzen, L and Bernard, L, 2013. Challenges of developing low-grade deposits in ænew worldÆ countries from a mining consultantÆs perspective, in Proceedings World Gold 2013 , pp 307-314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By E McLean

The decision making check-list and hierarchy of information for process and plant design is generally wide-ranging and complex. The nature of grades, mineralisation and ore types in an ore body, its mine development sequence, and the body of results from metallurgical and physical test work present complex and competing influences on flowsheet development, values for design, equipment selection, plant efficiencies and operating strategy. The challenge is how to manage all these variables, to understand their impacts on performance, and how best to provide a cost-effective plant design and robust process that meets daily/weekly/monthly operating objectives. Throughput, production and grade or product specifications need to be met. The ore body is not average; its range of metallurgical and physical characteristics may be moderately to highly variable. This paper assesses some of the key competing influences and conflicting issues in design and equipment selection, and their effect on production and performance expectations.

Aug 8, 2011

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

By M F. Gazley

The amphibolite-facies metabasaltic rocks of the Mine Mafic Package at Plutonic Gold Mine, Marymia Inlier, Western Australia, contain an estimated total endowment of 12.2 Moz of Au, which includes 4.71 Moz of past production and 2.77 Moz of reserves and resources; the remainder comprises lower-grade inventory. Over 65?000 multi-element analyses of whole-rock core and face channel samples from the underground workings of the deposit have been collected by portable X-ray fluorescence (pXRF) using a handheld Innov-X Omega pXRF unit. The analyses were performed on pulverised samples through paper bags, and were corrected using a pulverised, matrix-matched, reference standard. This method of data correction compares favourably with conventional XRF analyses performed on the same samples.A preliminary study based on pXRF analyses from a small number of drill holes found that a geochemical stratigraphy was evident in the pXRF data, and that this stratigraphy strongly controlled the location of Au mineralisation. The present study incorporates a much larger pXRF data set that samples a greater volume of diamond drill core and face channel samples and presents the data in a three-dimensional (3D) framework.This data set allows an investigation of the mineralogy of Au mineralisation with varying geochemical associations across the deposit. Historically, there has been a strong relationship identified between As and Au, which has caused issues with metallurgical performance, rendering some areas of the deposit only marginally economic. Utilising seamless data integration of the pXRF data set allows for recognition of the different styles of Au mineralisation using elemental concentrations and ratios from the multi-element analyses (Au:As, Au:As:Cu, As:Cu vs. K:V), and to visualise the distribution of these different mineralogical associations in 3D. The results of the 3D modelling and geochemical characterisation of the different styles of Au mineralisation are currently the focus of an extensive metallurgical testing program, the preliminary results of which are presented here.

Aug 22, 2011

By L Klemettinen, A Jokilaakso, D Attah-Kyei, P Taskinen, M Tiljander, D Sukhomlinov, D Lindberg

In this study, the use of carbon neutral biochars as reducing agents in the pyrometallurgical treatment of nickel slag was investigated at 1400°C in order to recover valuable elements such as copper and nickel from the slag. A large amount of slag is generated during the nickel matte smelting. Nickel slag contains valuable elements such as copper, nickel and cobalt, which can be recovered. Disposal of this slag results in loss of resources and may cause pollution of the environment. It is important to retrieve these metals for environmental and economic reasons. In this study, the slag was reacted with non-fossil reducing agents (biochar) which were produced from hydrolysis lignin and black pellet biomass pyrolyzed at 600 and 1200°C and with metallurgical coke for comparison. The reduction experiments were done at 1400°C for 15, 30 and 60 mins under inert gas atmosphere. The samples were quickly quenched and analysed with Electron Probe X-ray Microanalysis (EPMA). The results showed that the use of biochar resulted in faster reaction kinetics in the reduction process compared to coke. The fast reaction kinetics is attributed to the relatively high content of volatiles in this biochar, leading to gas formation and thus mixing of the sample material. Moreover, thermodynamic modelling was also performed using FactSage™ to simulate equilibria with different amounts of biochar. The metal to slag distribution coefficient calculated from the results of thermodynamic modelling were consistent with experimental results. In addition, thermodynamic calculations confirmed that nickel is reduced rapidly and it deports to the metal alloy phase. As the reduction progresses or extra reductant is available for reactions, more iron is deported to the metal phase. The calculations also revealed that Zn vaporises into the gas phase.

Jun 19, 2024

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By G Cavanough, A Olsson, J Rock, A C. Torrance

There are various methods currently in use to determine detonation performance of bulk explosive products including velocity of detonation (VOD), high speed photographic analysis, fragmentation analysis and unconfined detonation of samples. For assessment prior to detonation the current practice is limited to a measurement of cup density. This paper presents additional techniques that have been developed to provide measurement and assessment of bulk explosive products. Techniques applicable prior to detonation include a mobile laboratory to allow on-site chemical and physical analysis of sensitised products and ‘in-hole density’ measurement to monitor the in-hole density during sleep time. Assessment of detonation performance is achieved using detonation pressure sensors. These sensors allow measurement of detonation pressure, average VOD, propagation time and magnitude of the pressure induced in the explosive column by detonation of adjacent blastholes.CITATION:Cavanough, G, Torrance, A C, Rock, J and Olsson, A, 2015. Measurement and assessment of bulk explosive products, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S O. Hille

Modern remote mining operations in Australia are more commonly trending towards fly-in/fly-out (FIFO) sites. This trend is driven by numerous factors including increased business centralisation, reduction in operating costs, and a desire to live in coastal cities that offer closer family networks and a greater diversity of facilities. Consequently, the resource development industry has had to adapt. When WMCÆs Mount Keith Nickel Operation commenced operations in 1994, it was developed as FIFO for its entire workforce. Since then, there have been several permutations of rosters within a 21 day compressed work cycle including the 14/7 cycle. This paper discusses a case study of the change in management process to the 9/5 work cycle focusing on minimising fatigue in the workplace. It includes the discussion of the business case, employee reaction and the practical application. The impact of the best practice change after 18 months is discussed.

Jan 1, 2002

By S Brochot

During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material coming from a selection of various drilling products or a sample coming from a mining test. This sample can represent several tonnes of material which are analysed and split to be used in various tests.In the current case, a composite sample is dedicated to semi-autogenous grinding (SAG) pilot plant tests. The property of interest is then the size distribution of the material. The sample is mixed and a subsample is taken to measure the size distribution which is considered as the feed size distribution. Then the remaining material of the sample is divided in several subsamples for batch grinding tests at different operating conditions. The product of each grinding test is then analysed to measure its size distribution.The grinding performances are analysed at the light of the measured size distributions for feed and product. But what is the accuracy of the measurement of these size distributions? What is the variability of the feed knowing each feed is just a subsample of the initial sample?The Pierre Gy theory of sampling answers these questions.The current paper presents, through a real example, the calculation of the measurement error of the size distributions and the variability of the feed between the different tests. The uncertainties of the grinding performances are then calculated and their impact on the results interpretation is then analysed.CITATION:Brochot, S, 2012. Sampling for grinding pilot plant test - the effect of size distribution variability, in Proceedings Sampling 2012 , pp 127-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By R McDonough

DTL2 contract C916 was awarded in March 2009 for S$340 M. This contract includes two mass rapid transit (MRT) 1100?m long bored tunnels using two slurry tunnel boring machines (TBMs), with an internal diameter of 5.8?m, two cross passages and 135?m of cut-and-cover tunnels The contract also includes the design and construction of a new underground station including station entrances, subway links, architectural finishes and external landscaping. The station, located at Upper Bukit Timah Road near Jalan Jurong Kechil will also double as a civil defence shelter.The works included significant traffic management in a dense urban area in order to create the working areas whilst keeping the requisite number of traffic lanes. This involved numerous utility diversions and included the removal of a 33-year-old pedestrian overhead bridge (POB) over busy Bukit Timah Road. The station and tunnelling works were completed on time, including a ‘dock and dismantle’ TBM retrieval and subsequent breakthrough of the separating wall.This paper will detail the methods and solutions used to construct the tunnels and stations, with a focus on the requirements for construction of the station to be a civil defence shelter if required. This involved solutions to tying reinforcement and placing concrete to high standards in a restricted space, as well as the incorporation of heavy blast doors and other associated protective measures. The efforts of the management team resulted in the project being awarded first prize in the 2011 Land Transport Authority’s Annual Safety Award Convention and being named winner of the Safety and Health Award Recognition for Projects (SHARP) award at the 2011 Workplace Safety and Health (WSH) Awards. As well, McConnell Dowell won a Green and Gracious Builder Award (Excellent Category) from the Building and Construction Authority (BCA).CITATION:McDonough, R, 2014. Design and construction contract C916 Beauty World Station and Tunnels, Singapore, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 411–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Schonert, K Eichas

Electrostatic separation of non-conductive materials can be accomplished by triboelectric charging. The efficiency of convential separators becomes worse in the size range below about 100 ¦m. These problems are solved by developing a new double-drum-separator. The investigations have shown the possibility of separating very fine mineral mixtures (eg quartz/calcite) in a strong electric field after tribo-charging in a special dust-feeder. The paper reports about the influence of particle size and field intensity on the separation and deals furthermore with the problem of desagglomeration.

Jan 1, 1993

By A Coelho, D Bruce, H Grosser, C Parken, M Xia

Carrapateena is a new underground sublevel cave mine and was officially opened in 2020. It has a mine life of 20 years. Development began in 2016, and with the rare opportunity to start a with a blank canvas and having a long mine life, an effort was made to explore how to incorporate innovative and leading-edge technologies. The Ventilation on Demand (VoD) system was designed with the objective to optimise power consumption and ventilation delivery through the primary and secondary ventilation systems. Primary fans controlled by Variable Speed Drives (VSDs) and dualwinding secondary fans with multiple setpoints control the delivery of overall quantity. Automated butterfly dampeners control the regulation of air to individual production crosscuts, and automated louvres control the exhaust quantities from the mining levels. Ultra-sonic flow sensors are installed to measure air quantity and environmental stations are installed to measure air quality. Both are designed to play a key role in control and calibration of the system. It was quickly identified that no one vendor could provide a holistic solution to meet the design requirements. A strategy was derived to use multiple vendors, harnessing the specific strengths of each. A control system has been developed to allow the Site Operations Control Centre (SOCC) to oversee and control real-time delivery of ventilation as required by operations. The first full level installation of the VoD system was completed in September 2020.

Mar 15, 2021

By J Cronin

For the last decade, we have read about the great technical innovation that is coming to the mining industry that will increase safety and productivity. There is consensus that it will be a technical innovation that will produce a step change in mining costs and outputs (as opposed to bigger machines or less people); however, this innovation (while freely available) has not taken hold in the industry. While there are a few mines that have embraced technology, the majority of underground mines simply do not have the expertise or technical capability to implement innovation and automation.With unexploited mineral deposits becoming deeper and more remote, and thus more hazardous to mine, telepresence offers the ability to remotely execute production tasks while separating personnel from hazards. As the technologies required to deliver telepresence mature, the potential for there to be no personnel underground during production activities is becoming a reality (the ‘dark factory’). So significant is the capacity of telepresence to mitigate risk, it is proposed that it be included as a separate entry in the hierarchy of hazard mitigation controls.Technical innovation such as the optimised short-term interval control of the production process and the automation of underground mobile fleets offer significant increases in production along with lower operating costs. This paper explores the most critical components for the successful implementation of technology in underground mining; redundant, robust and high-bandwidth communications networks to carry data from distributed networks of smart sensors and to convey teleoperation commands; and high-definition video to provide operators with detailed, real-time data. The days of analogue ‘leaky feeder’ as a base case for communications are over. The human resources required to support the expected wave of innovation are significant and will be difficult to maintain in remote areas as the same skills and expertise are in demand in other industries.The paper highlights barriers to innovation in the mining industry, and a lack of technical and scientific expertise within the industry to be able to identify, implement and manage technologies that can increase safety and productivity. As well, an over-reliance on basic net present value (NPV) financial analysis that is used in the industry punishes investment in technology (capital expenditure; CAPEX) and accepts higher operating expenditure (OPEX) due to the discounting of future savings in operating costs.CITATION:Cronin, J, 2017. Telepresence – the application of remote control and automation technologies for increased safety and productivity, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 213–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By N S. Weerasekara, S Town, E Lessing, J A. De Torres

Philsaga Mining Corporation (Philsaga) had three main aims in converting their lining system from steel to metal cap. They wanted to increase mill availability, minimise localised high wear and optimise particle breakage to deliver increased efficiency within the milling circuit. Combining Discrete Element Method (DEM) modelling and empirical interpretation of liner wear resulted in a rigorous approach to understanding the impact of mill liners on overall mill performance. This new understanding was subsequently used to not only derive a new lining design to optimise performance and thereby improve overall plant economics, but also to guide further lining development.In this work, detailed DEM modelling, developed from actual plant data, together with optimising liner design for wear paved the way towards the installation of a Metal Cap lining system at Philsaga’s Ø6100 mm SAG Mill. The results were a reported increase in SAG mill throughput of 16 – 20 per cent due to improved breakage through more efficient use of installed power, a reduction in localised high liner wear with overall increase in liner life and reduction in liner replacement time. Site also reported an increased gold recovery of 2 per cent which the improved breakage might have contributed to. This paper will present the design challenges and compare the Metal Cap lining systems performance against Steel lining system. CITATION:Weerasekara, N S, Lessing, E, Town, S and De Torres, J A, 2018. Metal cap versus steel lining system at Philsaga Mining Corporation’s Ø6100 mm SAG mill, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 653–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By C Cavern, G Jacobs, F Durufle, L Ameglio

Airborne geophysics and geomatics is at a crossroads as to whether it remains a viable mapping tool, both technically and commercially, and broadens its potential for new applications (eg environmental monitoring, civil engineering and precision farming). The use of small and stable multisensor aerial platforms to conduct highly flexible surveys flown at a low/reasonable cost of operation is a recurrent wish of many stakeholders in the natural resources exploration and mining industry. Through its Fly Light Airborne Geophysics research program, EXIGE and partners have pushed the development and testing of two new airborne carriers with unique capabilities for geo-surveys: GyroLAG’s gyrocopter and Infotron’s unmanned aerial vehicle (UAV). These carriers are the next generation of versatile and innovative aerial vehicles for remote sensing and monitoring. They are rotary, smart tailored, ultra-high resolution manned (gyrocopter) or autonomous (UAV) airborne platforms that combine the merits of dense data sampling, accurate position location, very low clearance above ground or sea level, slow speed, interchangeable and combined multiple geo-sensors, automatic data quality control and real-time quality assurance. They also have the benefits of being highly efficient, cost-effective, commercially attractive, safe, reliable and easy to deploy and operate. Their technical specifications and multiple advantages compared to traditional aircraft and/or ground crews are presented in this paper. An overview of various geo-sensors (magnetic, gamma-spectrometry, visual, near-infrared and LiDAR) carried on-board is also provided.CITATION:Ameglio, L, Durufle, F, Jacobs, G and Cavern, C, 2015. Light airborne platforms for monitoring mines and minerals, in Proceedings Third International Future Mining Conference, pp 11–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015