Search Documents

By P J. Terbrugge

Many ore deposits have considerable vertical extent which is not always known at the time of commencement of mining. In many of these cases, initial mining is by opencast methods, and as ore reserves are proved to greater depths, the pits are often planned to go deeper than had been originally envisaged. In such cases, surface plants and critical underground facilities such as conveyer tunnels, access ramps, ore passes, hoisting shafts and ventilation shafts are often located much closer to the pit rim and the orebody than is desirable for the deeper mining situation. This usually raises the question of the stability of such underground excavations, which may be critical for the viable longer-term mass underground operation of the mine. In this paper the key considerations in the evaluation of the stability of the overall mining environment for ædeepened minesÆ are defined. Aspects which are dealt with are: open pit stability, shaft stability, dilution, mudrushes and airblasts, and selection of mining method. The necessary stability evaluations are put into the appropriate context by considering two case histories. Critical parameters and considerations which need to be addressed during the evaluation of excavation interaction are also discussed.

Jan 1, 2000

By A A. Puhalovich

The placement of chemically reactive mine wastes in mined out pits (æpit backfillingÆ) is increasingly seen by industry as best practice to manage long-term environmental risks. This is primarily because leaving wastes at the surface, or allowing pit lakes to develop, can result in unacceptable environmental risks. The costs and practicality of mitigation options such as installation of covers and community expectations of landform re-construction to achieve a post-mining, beneficial land use are also important drivers for pit backfilling.Pit backfilling can significantly reduce the post-closure risks to receiving environments, by minimising seepage due to tailings, acid/solute generating waste rock and/or salts derived from mine water treatment. Environmental risks are often highest where wastes are located close to the ground surface, due to relatively high rates of groundwater movement in near-surface aquifers and/or failure of engineered structures due to rainfall/erosion processes. Placement of these wastes at significant depth in pits, subject to mine planning and environmental assessment, can address these risks by increasing the path length and resistance from contaminant source to receptor, thus enhancing encapsulation of the wastes.Pit backfilling can also be cost-effective for mining companies. This is because existing pits are developed on the basis of an economic return and thus provide an opportunity to store tailings in an existing æengineered structureÆ at little or no incremental cost when compared with building and operating a new tailings or waste rock storage facility, often encompassing complex cover/drainage management systems. Key issues for consideration are mine planning, the long-term geotechnical behaviour of the wastes (eg consolidation of tailings which leads to release of acid/solutes in tailings porewaters), seepage rates to downstream receptors/agreed end point criteria and potential resource sterilisation. Internationally, mine closure guidelines are also showing a greater recognition of pit backfilling in the context of allowing mining companies to meet agreed post-closure land use objectives.In summary, pit backfilling can enhance the encapsulation of chemically reactive mine wastes and environment protection, and with agreement on post-closure beneficial land use, can also help to deliver post-closure benefits to communities.CITATION:Puhalovich, A A, 2012. Pit backfilling - Managing chemically reactive mine wastes and achieving rehabilitation objectives, in Proceedings Life-of-Mine 2012 , pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By I Elias, E Moya, S Chaffer

This paper is based on a case study from a mine site that operates two gyratory primary crushers. These crushers were encountering problems, which included inconsistent P80, reduced liner life tonnage and, on some occasions, catastrophic failure of the liners.As part of an evaluation process, both crushers were ‘mapped’ using a technology for condition monitoring and modelling of the crusher’s wear components. The technology provides comprehensive coverage of the crusher’s concaves and mantle at 100 mm intervals. It also automatically assesses wear rate between inspections and determines the highest wear areas. Outcomes include projected optimum reline dates at target replacement thicknesses, the identification of asymmetrical wear patterns, and the accurate measurement of open and closed (OSS/CSS) side settings.A comprehensive study was performed to optimise the performance of both these crushers at site. Over a period of seven liner service lives, the strategies to improved performance included liner analysis (concaves and mantle profile analysis), tonnes per day (t/d) and tonnes per hour (t/h) analysis, mantle reutilisation, detection and control of loose concaves, and detection and control of uneven wear and hot spots.These strategies resulted in the improved mechanical and operational performance of both crushers through concave and mantle redesign, OSS/CSS control, accurate wear forecasting plus other initiatives.As a result of these initiatives, the site now experiences benefits which include consistent product size, increased tonnes per hour (t/h) for both crushers and the liner life tonnage has doubled. Additionally, further benefits include less downtime for crusher liner maintenance and the reduced cost of inventories by mantle reutilisation.CITATION:Elias, I, Chaffer, S and Moya, E, 2015. Improvements in service life and cost reduction for gyratory primary crushers through mantle and concaves optimisation – a case study, in Proceedings Iron Ore 2015, pp 115–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Murray C. G

A database of over 1300 earthquakes has been used to investigate the relationship between seismicity and tectonics in two areas of eastern Queensland and NE New South Wales. These areas have been monitored by several networks that were installed primarily to monitor seismicity associated with the impounding of large reservoirs. Events that occurred prior to the installation of these networks have been excluded from the analysis because they have large uncertainties in location.Seismicity in SE Queensland and NE New South Wales is concentrated in the coastal regions. Activity also extends off the coast of Queensland and beyond the continental shelf. The coastal activity is mainly within the New England Fold Belt. An area of the fold belt overlain by the Clarence-Moreton Basin is also active. There is an area of activity near St. George that correlates to the Wunger Ridge. Fraser Island and the adjacent onshore area, near Maryborough, are notably aseismic.Within the New England Fold Belt there is a NNW trending zone of concentrated activity that includes the South D'Aguilar Block and the Esk Trough as far as Gayndah. The Nambour Basin, the Gympie Province, and the southern portion of the Yarrol Block are significantly less active.Composite focal mechanisms of several groups of accurately located earthquakes in SE Queensland indicate predominantly reverse faulting. This faulting is the result of the crust being compressed horizontally in a NE-SW direction.Activity in the Burdekin Falls Dam area of central eastern Queensland is confined to the Drummond and Bowen Basins. There is also significant activity offshore from Townsville and Bowen.

Jan 1, 1990

By Forrester P. I, Richardson W

Methane in coal mines is an ever present hazard resulting in loss of lives and serious economic consequences. For effective control of methane, ventilation alone may not be totally adequate in some situations. In order to deal with such cases, new methods for the control of methane are being researched. One such method based on biotechnology has been investigated in Canada in the past several years. This method involves bringing methane oxidizing micro- organisms into contact with coal to oxidize the methane released to non-flammable products.

Jan 1, 1988

By B Jones, M Chappell

Installing ground support correctly is not an easy task, whether lack of operator training, poor ground conditions or underperforming equipment. Confirming the quality of installation can help with planning and remedial works and help to maintain a safe working environment. A 2?m bolt with 700?mm of encapsulation will pass a 10?t pull test (assuming ground conditions permit); however, it will not provide any data of the unencapsulated length and thus the ability to withstand corrosion. Complimentary testing in the form of non-destructive testing (NDT) can provide factual data that leads to the assessment of the quality of the encapsulation. By improving the quality of the encapsulation, the risk of corrosion is reduced, the ground support durability is improved and hence the asset life is enhanced.This paper presents a case study of a trial using the NDT system RokTel™. Installations of varying quality were installed and tested. The characteristics tested were corrosion, load and free length. These characteristics can be tested and assessed for cable bolts, thread bar bolts and split sets. The aim of this paper is to present NDT testing as a viable method for assessing installation quality and ongoing performance of the ground support.CITATION:Jones, B and Chappell, M, 2014. A non-destructive testing method for measuring bolt condition, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J M. Galvin

History attests to the catastrophic consequences that fire, explosion and contaminated, noxious andirrespirable atmospheres can have for workplace health and safety in underground coal mining. It also confirms that fires and explosions present the greatest risk of partial or total loss of underground mines and equipment and that this risk continues to materialise. The design, implementation, operation and maintenance of the mine ventilation system are core controls for managing the hazards associated with these risks, both for preventing them from materialising and for mitigating their consequences if they do materialise. These are most effective when embedded in a risk management approach.

Oct 12, 2022

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By Kleine T. H

Blast design involves many engineering constraints and objectives. Some of the more important include the implementation costs, the desired fragmentation and shape of the muckpile. A spreadsheet has been developed to allow blast design options such as burden, spacing, blast hole diameter, decking and explosive type to be varied. As any option is varied the spreadsheet recalculates and graphs the expected implementation costs, fragmentation and muckpile shape in seconds.The spreadsheet extends the philosophy of simple robust fragmentation prediction (Cunningham, 1983) to include similar models for explosive detonation (with respect to explosive type, age, blast hole diameter and density) and muckpile shape (with respect to burden, spacing, charge location and weight). The new empirical models for explosive detonation and muckpile shape prediction have been calibrated successfully for one situation and are now undergoing further field trials.

Jan 1, 1992

This paper describes the development of an approach to sustainable development for application at the feasibility study stage for a proposed bauxite mine near the community of Aurukun, south of Weipa on the western coast of Cape York Peninsula, Queensland, Australia. The general environment for development was complex in all dimensions. In particular, the socio-demographic profile of the Aurukun community (population 1200) characterised it as being amongst the most disadvantaged communities in Australia. The traditional owners of the area, the Wik and Wik-Way people, were at the forefront in the efforts of Indigenous people in Australia to secure land rights over the past 30 years, and they had previous experience negotiating an Indigenous Land Use Agreement (the Western Cape Communities Coexistence Agreement) with Rio Tinto Alcan, the operators of the Weipa bauxite mine. Through this they had shown a well-founded sense of entitlement with respect to the development of resources on their traditional land. The Queensland State Government had recently cancelled an existing mining lease over the bauxite resource as the holder of the tenement had not fulfilled the terms of a development agreement that had been in place for 30 years. The Government was anxious to avoid any future æbankingÆ of the resource, and had decided to offer tenure to the resource on an international competitive basis, subject to the requirements of the Commonwealth Native Title Act 1993. This would require a negotiation process with traditional owners and potentially involve companies with whom the traditional owners had no existing relationship (typically developed during the projectÆs exploration phase) and who possibly had no project development experience in Australia. As well, the State Government envisaged an approach to development that drew on the significant work that industry and other stakeholders had undertaken over the previous ten to 15 years, commencing with the mining, minerals and sustainable development (MMSD) process. This work was aimed at rectifying acknowledged deficiencies with industry recognition of stakeholder interests, in particular with respect to environmental management and socioeconomic development. The approach adopted aimed to define the strategic community interests and sustainable development outcomes to which the development of the resource would be expected to contribute, and to embody these within an easily usable management structure that could be applied to each stage of project development from feasibility study through to mine closure. The logical framework (AusAID, 2006; ICMM, 2005) was the management tool utilised to order the identified interests and desired outcomes. The structure included components aligned with the key areas of development interest expressed by the community, and the initial baseline sustainable development plan (SDP) developed established component objectives, outcomes, indicative outputs and activities for the feasibility stage of the project. This established an objective framework to guide potential bidders when developing their response to the State GovernmentÆs Request for Proposal. The paper will describe the evolution of the competitive process and the parallel process for development of the SDP. While the institutional environment was politically and socially complex, the use of simple visual representations of the environment and the analysis and ordering of issues, objectives and criteria through methods such as stakeholder analysis and the logical framework approach, enable the development of a dialogue on the contribution that the development of a mining project can make to sustainable community development, and for the development of an agreed program of community support to capture the contribution. The use of the logical framework was found to have good functionality for plan development. Achieving plan outcomes though, is highly dependent on the skill of key project personnel in facilitation, team building, conflict resolution and leadership, as well as their ability to influence the behaviour of key stakeholders with the capacity and authority to require the integration of local economic development criteria in to key project development decisions.

Jan 1, 2009

By G Cao, Y R. Cui, J X. Zhao, H P. Gui, G H. Wang, Z M. Wang, M M. Ren, B Li

Pyro-metallurgy is still the main process for lead production and a lot of lead direct smelting processes have been developed in recent years. All the processes will experience two steps in common. The first is the oxidisation of PbS to PbO and then reduction from PbO to Pb, furthermore, from ZnO to Zn. So, the composition of melts, especially the slag composition at reduction step change continuously. Up to now, there are few systematic results on the slag physical-chemical properties with its composition change. In this work, the typical lead direct smelting processes were analysed from theoretical and practical standpoints. The full-period slag composition and slag melting point change were compared. Especially, to the PbO and ZnO reduction steps, based on the full-period slag composition change, the slag properties were predicted. Based on dust composition and test results, the mechanism of Pb compound evaporation and its effect on practice and measurement of high PbO bearing slag physical-chemical property is discussed. It is suggested that to restrain the evaporation in practice and to obtain more accurate measurement results of physicochemical properties of smelting slag are the key problem not only to set high efficiency, energy saving process, but also to environmental pollution control.

Aug 21, 2024

By S Hapugoda, J R. Manuel, X Cao, B D. McDonald, N A. Ware, L Lu

Roy Hill is a large iron ore mining, processing, railing and port operation in the Pilbara region of Western Australia. Since delivering its first shipments to customers in December 2015, Roy Hill has quickly achieved a 60 Mtpa production rate of lump and fines products. The process plant, principally consisting of wet scrubbing, screening and de-sanding unit processes, was expanded from early 2020 to include operation of a Wet High Intensity Magnetic Separation (WHIMS) Plant. The WHIMS Plant treats tailings to recover approximately 4 Mtpa of ultra-fine (nominally -150 μm) high-grade hematitic concentrate which, after dewatering, is blended into the fines product. Unlike typical hematite concentrates, which consist largely of dense particles with smooth surfaces, the WHIMS concentrate is characterised by very finely microporous hematitic/goethitic particles, reflecting the overall characteristics of the Roy Hill deposit. Detailed test work has been conducted in collaboration with CSIRO to characterise the WHIMS concentrate in terms of its physical and mineralogical properties, and to determine its influence on the granulation and sintering performance of Roy Hill fines – from fundamental/lab-scale and sinterpot perspectives. The results demonstrate that blending of the high-grade hematitic Roy Hill WHIMS concentrate into the fines product can maintain overall sinter quality and positively influence granulation and sinter melt formation, as well as Fe grade.

Nov 8, 2021

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

The ASC has a dual role of business facilitator and law enforcer. Only certain types of expert report are of interest to the ASC. The powers of the old Companies Code and the Corporations law are compared. NCSC Policy Release 149 was dependent on the prescriptive powers given to the NCSC in the Companies Code. The Corporations Law does not give the ASC power to prescribe the contents of expert reports. The requirement now is for all necessary information. Research evidence is that some investors want simpler prospectuses while others need more detail. The ASC's examination of expert reports is after registration of primary documents. This leads to a necessity for experts to maintain adequate records.

Jan 1, 1994

By M Ranjan, C R. Borra, P Palai, P P. Sahoo

Change in mould slag composition during casting of medium alloy steel is caused by the redox reaction between molten steel and mould flux. Mould flux generally contains a certain amount of SiO2, but elements such as Al, Mn and Ti in high/medium alloy steels reduce SiO2 in the mould flux, causing remarkable changes in the composition of the mould slag. As a result, the properties of the mould slag change greatly as continuous casting proceeds. This causes casting instability, process abnormality and casting defects. Effect of Ti as an alloying element in steel on mould slag is studied extensively through high temperature laboratory measurements and plant measurements. TiO2 gets picked up by the mould slag up to 3 per cent during casting a steel grade containing 0.1 per cent Ti. This changes the mould slag composition and results in decreasing the slag viscosity by up to 10 per cent and decreases slag break temperature by 30–40°C.

Aug 21, 2024

By S Whitton, W Wimmler, L Wimmler

“Given the increasing scrutiny of the mining industry and its relatively poor record with regards to mine tailings management, increased requirements to minimise water usage (often accompanied by very high costs of water) and the need to demonstrate achievable long-term closure strategies, it is likely that the option of a filtered tailings system will need to be considered in many operations in future.” (Australian Centre for Geomechanics, 2018). Given such a statement as a conference introduction, it is only appropriate that a range of potential technologies are investigated and compared, to create awareness for even underrated but appropriate technologies. The advantages and disadvantages of all technologies need to be considered and analysed. Suppliers are swift to promote their technologies advantages; however aspects of sustainability are not always fully understood. Perhaps a combination of two filtration technologies is appropriate. This paper delves into the technical details, good or bad, of four mechanical dewatering technologies in tailings dewatering and provides insight on an undervalued and, in the author’s opinion, young technology – the screw press.

Jul 1, 2021

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

By C Nyoni, T Nguyen, C R. W Seymour, G D. Dempers

Unplanned dilution directly adds cost to production from mining, milling, tailings disposal and administration. Additionally, unplanned dilution decreases the productivity, profitability and may affect the planned life of mine. Identifying and quantifying the potential for unplanned dilution allows optimisation of the mining plan and mining practices to minimise the adverse impact on productivity and the cost of production. The Dilution Rating System (DRS) has been developed to more accurately predict dilution thickness and the variable potential for dilution, from individual stopes to life of mine planning. The DRS utilises the methodology developed for the Mining Rock Mass Model (Seymour et al 2007, Jenkins et al 2009) to generate a three-dimensional dilution rating model, which is then calibrated against stoping performance. Dilution can be predicted more accurately and the parameters affecting dilution can be determined and minimised through improved mining techniques, for example blasting and ground support design. Potential high dilution areas can be identified in the planning stages of the mine and systems put in place to mitigate the risk of excessive dilution. This paper presents the methodology used to develop the DRS and then successfully predict dilution for both the hangingwall and footwall of stopes at the Gara Gold Mine. This has enabled the expected dilution to be more accurately predicted and mitigated where possible thus reducing unplanned dilution.

Mar 15, 2021

By S L. Nicol, B J. Hogg, O J. Mendoza, S Nikolic, A Burrows

The top submerged lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. The key advantage the ISASMELT™ TSL technology provided was the ability to process feed materials in a highly turbulent bath, reaching close to equilibrium conditions, uniquely allowing for operation below the liquidus of the molten slag phase. The details on what happened below the liquidus line in the phase diagram became critical for the successful operation of the technology. During the development of the ISASMELT™ technology this led to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore Technology, and the Pyrometallurgy Research Centre (PYROSEARCH) at The University of Queensland. The fusion of the phase equilibria research into the technology development allowed for understanding of the behaviour of molten splash, reliable tapping of the furnace, and the ability to operate the furnace with a refractory lining and achieve a year campaign life in excess of four years. The outcome has allowed for the highly successful adaption of the ISASMELT™ technology to recycling of complex feed streams necessary to drive circularity in our modern global economy.

Aug 21, 2024

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018