Search Documents

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By G W. Swana

Elastoplastic parameter is a parameter that describe how much materials behave elastically up to certain stress states and plastically thereafter (Hudson and Harrison, 1997). In the continuum analysis, two main parameters of the elastoplastic parameter are modulus elasticity and Poisson’s ratio. In the slope, elastoplastic parameter holds the main role for stability related to deformation in ductile type of rock. There’s a limitation to determine elastic or plastic deformation at the field for ductile rock type. Field manifestation commonly showed that there was no accumulation zone during and after the sliding failure mechanism, in other hand, at the research area, manifestation of deformation at the toe of slope only indicated by bulging shape. This paper will focus at the sliding failure occurred at Coal mining Pit Y owned by Arutmin Indonesia, which according to failure investigation report similar with the condition described above. This paper also will be based on two hypotheses, first hypothesis is claystone rock mass has not been reached plastic deformation yet and the second hypothesis is there is a chance that elastoplastic parameter of the rock mass has been changed during the deformation/sliding failure process. Research method of this paper are back analysis using probabilistic analysis in Finite Element Method (FEM), which conducted before and after failure. Then, the result of the displacement or deformation of the analysis will be checked with the actual deformation shape. Meanwhile, the change of the elastoplastic parameter will be analysed and interpreted. This paper hopefully able to be developed to study about elastoplastic behaviour of rock mass in actual condition and the influence of another uncertainty factor which determine the slope stability.

Nov 29, 2022

By J D. Goldsworthy

The McPhee Creek bedded iron deposit is a recent discovery made by Giralia Resources NL (Giralia) in the northern Pilbara of Western Australia. The deposit lies 30 km north of the town of Nullagine along the southeastern margin of the East Pilbara Granite-Greenstone Terrane (EPGGT).The McPhee Creek area is located in the Kelly Greenstone Belt in the southeastern part of the EPGGT. The Archaean aged greenstone belt consists of volcanic and sedimentary sequences including the Warrawoona Group and the Gorge Creek Group. The McPhee Creek iron ore deposit lies within banded iron formation (BIF) rocks of the Gorge Creek Group. The structure of the McPhee Creek area is dominated by a northeast trending, upright synform (Sandy Creek Syncline) and associated folding that is truncated by northeast trending faults in the east. Iron ore mineralisation is predominantly stratabound and follows the dip of the bedding – however, in some areas, particularly in the southwest of the deposit, mapped steep to moderate dips of bedding planes are at odds with underlying fl at mineralised zones in drill sections. Zones within the deposit that contain substantial thickness of iron ore correspond to areas of complex folding suggesting structural control and iron enrichment in fold hinges. Petrographic analyses confirm mineralisation is goethite dominant and the deposit is strongly supergene enriched.Giralia initially identified iron ore potential in the McPhee Creek area through the presence of a small known channel iron deposit (CID) mesa. Giralia began exploration in 2008 by re-drilling a portion of the CID (subsequently named Crescent Moon) and reported a small low-grade Inferred Mineral Resource. Target generation in the wider area utilising Geological Society of Western Australia maps and Ikonos satellite images identifi ed strongly ferruginous outcrops associated with major structures along an 8 km long range located 2.5 km to the west north-west of the Crescent Moon CID deposit. In late July 2008, a total of 62 rock chip samples were collected during a helicopter supported sampling program conducted at McPhee Creek. Samples taken from haematite-goethite enriched BIF and canga zones outcropping intermittently over the 8 km length of the western and central areas of the prominent range assayed up to 63 per cent Fe. These zones represent the discovery outcrops and surface expression of the McPhee Creek main range iron ore deposit.Follow up sampling, geological mapping, bulldozing of access tracks and ramps and reverse circulation (RC) drilling commenced in September 2009. A maiden Inferred Mineral Resource was announced by Giralia to the Australasian Securities Exchange (ASX) on 15 December 2009.The current Indicated and Inferred Mineral Resource at December 2010 stands at 260 Mt grading 56.2 per cent Fe, 0.12 per cent P, 6.7 per cent SiO2, 2.3 per cent Al2O3 and 9.5 per cent LOI at a 50 per cent Fe cut-off. McPhee Creek is one of the largest iron deposits found in Archaean BIF in the northern Pilbara.

Jul 11, 2011

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011

By C Itotoh, K O’Halloran, L Karlson

Global methods used to explore for minerals have progressed relatively slowly since the development of the first diamond core drill in 1863. Since then, key developments such as wireline geophysics (1920s), the tricone drill bit (1930s) and aeromagnetic surveys (1940s) all occurred in response to global events. In this project, BHP’s WAIO Geoscience operations team hypothesise that a global movement towards a greener future as well as an increasing intolerance for safety events will drive another step change in exploration methods. We have leveraged our relationships with exploration contractor partners and industry leaders to develop a realistic vision for 2033 and beyond, where drill rigs, earthworks and geophysical units are operated and maintained remotely; emissions of dust and waste are eliminated; hazardous energy sources are controlled; procurement is based on sustainability rather than cost and carbon emissions are tracked with the same rigour as production metrics. We have combined these visions into a series of graphical illustrations with the aim of inspiring ourselves, our vendors and our peers to collaborate further on producing a step change in our industry.

Sep 18, 2023

By T Schrimpf, I Bryan

The life cycle of a mining project begins with initial regional exploration and ends with mine closure and rehabilitation. Between resource definition and the commencement of mine construction is the study phase. In this phase technical concepts and processes are defined, evaluated and assessed with the aim of establishing whether the deposit is economically feasible. The study phase usually involves various steps from a concept/scoping study to prefeasibility and ultimately definitive feasibility study. The complete study phase can take several years. Although the costs for studies are low in comparison to actual construction and operating costs of a mining project, they are significant especially for junior exploration and mining companies advancing projects to the point of being funded.The studies aim to determine selected parameters for the project, eg mining and processing methods, operating strategy, etc and provide a roadmap for project development ahead. Although mining studies are of the utmost importance for the mining project and the project owner, they are usually carried out using a conventional engineering approach: the consultant or design engineer works to a defined scope of work. The resulting design might be based on good engineering, but might often also fail to provide the solution for the project owner that delivers the best shareholder value. An alternative to this more traditional approach to project evaluation is what we have termed a value engineering approach. Value engineering is a creative, organised effort, which in the case of a mining study analyses the requirements of the study for the purpose of achieving the essential outcomes with the highest shareholder value. The outcome of a study is a concept that delivers the highest achievable value of the resource project and shows the way ahead to realise this value. Through a group investigation by experienced, multi-disciplinary teams the value of the resource is improved through the study of alternative options, methods and processes. The scope of the study is not limited to a narrowly defined engineering scope, but to the creation of value.The study commences with the identification of key value drivers and risks, based on the available information (drill data, geotechnical data, metallurgical test work, etc). This enables the quantification of key uncertainties, risks and value adding opportunities. Study efforts concentrate on key value drivers and are not unnecessarily spent on side issues. This approach can significantly reduce the time frame and costs for the study phase.This paper describes in more detail RMDSTEMÆs value engineering approach to mining studies and illustrates it with examples and case studies.CITATION:Schrimpf, T and Bryan, I, 2012. The application of value engineering principles to mining studies, in Proceedings Project Evaluation 2012 , pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

Copper grades of diamond drill hole and development samples are determined in the core shed logging area at Mount Isa Mine using a Bulk Mineral Analyser. All geological and grade data on the copper orebodies is collected and stored on computer file.The raw data can be manipulated interactively using a computer terminal or by input of forms to produce output as computer plots or printouts. Grade distribution of copper or cobalt is obtained by the geologist using a computer kriging package followed by grade contouring. Computer plotted cross-sections and plans of individual stopes or several stopes can be produced showing geological structures, kriged grades at points and as grade contours.

Jan 1, 1985

The Ok Tedi Project has been planned as a selective mining operation since the Feasibility Study. The nature of the orebody, and the need to 'stage' the infrastructure buildup meant that initially the mill would process gol ore using a leach-CIP process, followed by parallel leaching of gold ore and flotation of copper ore, and finally all flotation of copper ore. Cutoff grades were applied to gold and copper ore of 1.0-1.3 g/t Au and 0.4-0.3% Tot. Cu. Since startup, unpredicted occurrences of sulphide copper and, to a Lesser extent, carbonaceous material, has necessitated significant additional short term drilling (other than at grade boundaries), and shift grade control in the pit to control contaminant levels. Remodelling of the orebody based on the most up to date variography and geological interpretation has had a significant impact on the reserves, and thus the whole project development strategy; necessitating the earlier processing of copper ores, and preflotation of the gold ore.This paper discusses some of these points in detail, and in particular highlights how unforseen geological occurrences coupled with processing restrictions can have significant impacts on ore reserves and the mine development schedule.

Jan 1, 1986

By T J. Grandfield

Paste fill has been used successfully at Henty Gold Mine for the past five years. It has allowed 100 per cent extraction of the orebody, stabilised poor ground and enabled wide sections and offsets to be mined safely. However, there are a number of inefficiencies in the current paste fill system. These include the low output from the drum filter, the addition of aggregate to the paste to compensate and the trucking of paste from the plant to the portal. These inefficiencies have increased the operating cost of the paste fill system and caused a number of operational challenges such as blockages and increased pipe wear. These challenges have been partly overcome by taking ownership of the paste fill process, improved quality control and better communication. Henty is currently developing two new orebodies, the Mt Julia and the Darwin and has an opportunity to build an efficient paste fill operation. This is likely to be a high density paste system without aggregate, either located above the new orebodies or located at the plant and pumped to the new site.

Jan 1, 2002

By Baafi EY, Chatterjee PK

The quality of mine planning decisions ultimately depends on reliable estimates of the characteristics of the orebody. The quant- ifiable factors such as grades or thickness can be estimated from field data gathered from outcrops or exploratory drillholes. Since outcrop data is necessarily limited to the periphery of a deposit, extensive drilling generally is required. This paper outlines a method for selecting the number and location of additional exploratory boreholes using an iterative procedure based on a mathematical optimization concept called fixed point theory. The method is illustrated through its application to an exploratory drilling program for a coal mine where optimized locations gave a lower estimate of regional and block variances than a manual Choice.

Jan 1, 1986

By E Widijanto, A Srikant

PT Freeport Indonesia operates a copper-gold mine located in the remote highlands of Papua, Indonesia, about 3500 km east of Jakarta. Currently, the district produces about 240 000 tonnes per day (tpd) of which about 45 000 tpd come from the DOZ Block Cave and the rest is mined from the Grasberg Open Pit. Over the next ten years, ore production from large block caves in the area is expected to reach about 200 000 tpd, replacing a large part of the production from the Grasberg Pit. Block cave mining alters the hydrological characteristics of the area being mined and when the cave expresses itself at the surface in the form of subsidence, it increases the entrapment area for surface water. Operating a large block cave mine in a region with an average annual rainfall of 5500 mm in steep mountainous terrain and complex geological and hydrological features presents a challenging scenario for dewatering or depressurisation of the area. The high rainfall infiltration and entrapment in stacked mines operating within an essentially single orebody, coupled with the presence of fine-grained and clayey material within the draw points of the block cave, creates mud rushes or wet muck spills, which can endanger the personnel and interrupt production. This paper outlines the problems caused by high water inflow into the DOZ Block Cave and the efforts undertaken to ensure the safety of the miners and continued achievement of desired production rates from underground mining in the district.

Jan 1, 2006

Although developed primarily for sintering tantalum, the unit to be described can be used to heat-treat metals in the form ofa bar, wire or strip, by passing a current through them. The upper temperature limit with this type of heating is the melting point of the metal being heated.The unit was designed for vacuum work, but. various gases can be used if required.Briefly, the vacuum sintering furnace consists of a bell which is counter-balanced and may be lowered onto the brass base plate which holds the electrodes. A rubber ring seal is used for vacuum work. The lower flexible grips are bolted to the brass base plate which is at earth 'potential, while the other electrode passes through the plate by way of an electrically insulated vacuum seal. This upper electrode, the height of which can be altered as desired, the lower grips, and the bell are water cooled. The vacuum line to the pumps and a line to the vacuum gauges also lead from the base plate. The more important sections of the unit are described below.THE BELLThe unit was designed so that the bell could be lifted clear of the base plate and the electrodes, thus facilitating adjustment of the latter and the mounting of the specimen to be heated. A double walled steel bell, 20 in. high, with t in. cavity was used. The bell was fabricated from 10 gauge mild steel sheet using a double overlapping run of arc welding for all seams. A water inlet and outlet...

Jan 1, 1946

By S Q. Liu, E Kozan

This paper proposes a new multiresource multistage scheduling problem for optimising the open pit drilling, blasting and excavating operations under equipment capacity constraints. The flow process is analysed based on the real-life data from an Australian iron ore mine site. The objective of the model is to maximise the throughput and minimise the total idle times of equipment at each stage. The following comprehensive mining attributes and constraints have been considered: types of equipment; operating capacities of equipment; ready times of equipment; speeds of equipment; block-sequence-dependent movement times of equipment; equipment-assignment-dependent operation times of blocks; distances between each pair of blocks; due windows of blocks; material properties of blocks; swell factors of blocks; and slope requirements of blocks. It is formulated by mixed integer programming and solved by ILOG-CPLEX optimiser. The proposed model is validated with extensive computational experiments to improve mine production efficiency at the operational level. The model also provides an intelligent decision support tool to account for the availability and usage of equipment units for drilling, blasting and excavating stages.CITATION:Kozan, E and Liu, S Q, 2014. An Open pit multistage mine production scheduling model for drilling, blasting and excavating operations, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 329–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Pan, G Qiu

In this paper, an analysis is made of the present situation in the Chinese steel industry and its demand for iron ores. It is shown that the demand for iron ores has been growing substantially with the rapid development of the steel industry all over the world, especially in China. However, the iron ore market is currently in the situation where supply exceeds demand due to the economic crisis, with more investment in mines and less output of steel for several years ahead all over the world. Gigantic pressure is confronting the Chinese steel mills due to the too high and irrational price of iron ores. It is time to return the price of iron ores to a normal position much closer to their value. More attention has therefore been paid to developing low-grade and complex iron ore resources in China due to the irrational price of imported iron ores. More innovative mineral processing processes have been developed to tackle these complex resources. A systematic introduction to the development of beneficiation processes for low-grade iron ores is provided, including upgrading low-grade siderite, limonite, micron sized haematite and magnetite resources.

Jan 1, 2009

By S Bluhm, L van den Berg

In planning mine ventilation systems, heat issues are normally associated with deep-level mines where auto-compression and virgin rock temperatures play a major role. However, a number of mines suffer from high ambient temperatures and humidity, very steep virgin rock temperature gradients and an influx of hot groundwater. Mines in Australia and, particularly, South-East Asia have to deal with these environmental conditions, both in the operational and planning phases. These operations normally have to take heat into consideration during the planning stages at much shallower depths. In high rainfall regions, the water table is saturated and groundwater flow rates are particularly high, which add significant water heat load potential to the mine ventilation system.This paper considers the ventilation challenges associated with hot groundwater conditions in mechanised mines. The paper is based on specific project experience gained from a number of projects in the United States, Australia and South-East Asia and draws on data from mines that experience hot groundwater conditions. For one site, actual decline temperature survey measurements, modelling techniques, management strategies and design considerations are presented.CITATION:Van den Berg, L and Bluhm, S, 2015. Ventilation planning considerations when dealing with hot groundwater, in Proceedings The Australian Mine Ventilation Conference, pp 211–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By N Herault

PT Freeport Indonesia recently completed preproduction development and construction of the Big Gossan underground copper and gold mine, located in the Ertsberg mining district of Papua, Indonesia. Production has commenced with an expected ramp-up to full production of 7000 tonnes per day in 2012. The Big Gossan utilises an open stoping mine method with paste backfill.In order to deliver ore to the mill, which sits in a valley above the ore deposit, an underground production shaft and hoisting facility was designed and constructed as the key component of ore haulage. The design and construction of the Big Gossan shaft posed many challenges to the project team. Available shaft design and construction expertise were limited as this was the first shaft of its kind in Indonesia and the project was undertaken during a time of high industry demand for new shaft systems. Construction resources were also limited due to the remote location and competition with existing, producing mines for these resources and skills. The project also taxed the ability of Freeport to provide services and resources to this as well as their other projects.Completion of the Big Gossan shaft was a milestone in PT Freeport Indonesia’s plan to fully transition ore production to the underground environment in this decade.This paper deals with the various challenges faced by PT Freeport Indonesia and shaft contractor, PT Redpath Indonesia, during the construction of the Big Gossan shaft and offers suggestions to improve future shaft projects of a similar nature.

Mar 21, 2011

The first hydraulic roof supports were installed underground in 1950s and ever since that time engineering developments have improved the supports in many different ways. However. advances in three main areas, the roof support mechanical design, hydraulic engineering and electronics have ultimately led to the point where, 35 years after that first installation. automation has been achieved and is now commonplace.The history of roof support automation has involved the continual integration of high technology engineering. Thera ate further possibilities for the future which combine to give some idea of the likelihood of there ultimately being a completely manless face.

Jan 1, 1991

By J Moffatt, T Payten, N Spooner, L Teixeira, L A. Balzan, G Wilkie, G Tsiminis

Fluorine is a penalty element due to its reactive nature. In acidic environments many fluorine minerals dissolve to form hydrofluoric acid (HF), changing processing conditions. When smelted HF can be released, causing negative effects to nearby people and the environment, as well as potentially damaging the smelter. Sale of ore with high fluorine levels elicit a financial penalty or are banned outright. Real-time sensors create the opportunity for instantaneous decisions on ore processing due to changing conditions. A fluorine sensor would allow rises in fluorine concentration in a processing stream to be flagged, and decisions on processing conditions or diversion to stockpile before processing could be undertaken. As fluorine is a light element, it is difficult to detect with in-field XRF devices and does not work well with PGNAA. There are currently no existing sensors to quantify the presence of fluorine in real-time, and thus decisions based on fluorine grade cannot be made at minute- or even hour-scales. Sensors designed to measure the presence of minerals that contain fluorine are a possible avenue to enable the real-time detection of this element. Mineral-based sensing may also give an added advantage of additional information about how the fluorine will react under different processing steps. The authors were given a grant under CRC ORE II (project number P1–005) to search for mineralspecific signatures suitable for real-time analysis. The work focused on novel regimes and applications of fluorescence as a means to detect specific minerals. The aim was to exploit fluorescence responses unique to minerals of interest in mining systems in order to produce sensors that address gaps in existing capability. After the successful discovery of signatures specific to two major fluorine minerals an additional grant (P1–014) was funded to develop the research into a prototype on-belt sensor, in partnership with Scantech International Pty Ltd. This paper details the development of a sensor package through multiple Technology Readiness Levels (TRLs) through collaboration with government/industry grant schemes, academics from university, and a sensor-focused Mining Equipment and Technology Services (METS) company. We give a brief description of the new sensor technique and provide a case study of multi-disciplinary collaboration.

Aug 24, 2022