Search Documents

At Hilton Mine, 18 kilometres north of Mount Isa, the silver-lead-zinc sulphide bodies have undergone strong deformation in the form of folding and later faulting and brecciation in the hangingwall region of the mine. Variation in grades and widths over compara- tively short distances causes problems regarding accurate sampling of orebody exposures in underground development, and in defining confidence limits for the extrapolation of ore intersections in ore reserve calculations. The paper gives a preliminary insight into the problem of obtaining representative samples for exposed orebodies and discusses the sampling techniques employed. Results gained from these sampling methods could not be verified due to lack of individual bulk samples for comparison but strong evidence for precision was provided. INTRODUCTION In a developing mine like Hilton, accurate grade information is of extreme importance. Original grade information for a potentially viable ore deposit is gained from surface drilling, and initial ore estimates are calculated from the resultant ore widths and grades. After underground development has proceeded, the opportunity arises for detailed examination of orebody exposures, and the resultant assay grades and widths from sampling of these exposures may, in the long term,

Jan 1, 1976

By J Ferreira

To speed up multivariate geostatistical simulation it is common to transform the set of attributes into spatially uncorrelated factors that can be simulated independently. One decorrelation method is the method of minimum/maximum autocorrelation factors (MAF), where a two structure linear model of coregionalisation is assumed. The transformation decorrelates the theoretical model exactly, but the actual data are only approximately decorrelated. The MAF transformation can therefore be seen as a special case of a non-orthogonal approximate diagonaliser of a set of symmetric matrices. A more general approach for approximate joint diagonalisation (AJD) has been developed in the context of blind source separation. For these AJD algorithms no assumptions are made beyond symmetry of the individual matrices and so they can be applied to a family of experimental semivariogram matrices. In their application there are no restrictions on the number of structures in the linear model of coregionalisation (LMC) thus removing one of the conditions placed on the subsequent modelling of the spatial structure of the factors. In this paper the general background for the U-WEDGE AJD method is presented. It is shown that the U-WEDGE method achieves better spatial decorrelation than the MAF method. The factors derived from U-WEDGE are simulated using conditional turning bands simulation and then backtransformed to attribute space.

Sep 26, 2011

By C Grobler, M Recklies, G Jiang, I Taylor, M Morgan, G MacDonald, L Smith

The resource estimation of lateritic deposits, such as Aurukun, presents specific issues related to the lateral changes in thickness and elevation of the various horizontal layers (or zones) within the deposit where the x and y dimensions are orders of magnitude greater than the z dimension. The objective was to develop a three-dimensional (3D) block model that retained the vertical and lateral variation inherent in deposits of this type to allow full optimisation of the production plan without prior selection of an economic portion (enriched bauxite layers) of the profile at the resource estimation stage. The Aurukun bauxite deposit is held by Chalco Australia Pty Ltd (Chalco) and forms part of the world-class Weipa bauxite province, Cape York Peninsula, Queensland, Australia. The bauxite is predominantly pisolitic with an upper boehmite-rich zone and lower gibbsite-rich zone. The bauxite consists of both in situ and reworked domains, is overlain by a thin soil horizon and has kaolinite clay as a transitional base. A portable infrared mineral analyser (PIMA) was utilised on site, in addition to elemental assay, on each drill sample to determine the mineralogy, in particular levels of boehmite, gibbsite, kaolinite and reactive silica. As part of the scope of work, a field program was undertaken using large diameter Boart Longyear sonic drilling to acquire detailed density measurements across the deposit to allow compliance with Joint Ore Reserves Committee (JORC) reporting requirements. Interpretation of the stratigraphy was conducted on a hole by hole basis with definition of the zone layering based on stratigraphy, geochemistry and mineralogy. The zone boundaries were then modelled as 3D surfaces and used to constrain a block model. The block model estimation used the ordinary kriging method, with the estimation done in unfolded space and then refolded, therefore maintaining the zones irrespective of thickness or orientation. The unfolding process converts the real-world positions for both blocks and informing samples to a scaled position relative to the roof and floor of each zone. Analysis of the data and variography were also undertaken in unfolded space. The x and y dimensions are unchanged, but the z dimension is a relative position. The effect of the unfolding and limits on number of samples per hole is to æpushÆ the informing sample search sideways but within the stratification, rather than vertically. This honours the strong vertical zonation within the bauxite profile. The JORC Code requires that the stated resource must have æreasonable prospects for economic extractionÆ. This is a qualitative rather than quantitative definition. A number of selection criteria to define a resource roof and floor were developed in consultation with the project engineers and owners to meet these criteria. The vertical selection of material to include in the resource highlights the variation in the development (and destruction) of the bauxite profile from area to area within the deposit.

Jan 1, 2009

By Tominaga Y

Mine ventilation control is one of the most important techniques to suppress the disastrous region within a limited area, to have enough time of emergencies (ignitions, fires and so on) for underground workers. The purpose of this paper is to introduce the simultaneous controlling of mine ventilation by using, micro computer connected to various kinds of sensors. In this study, basic of mine ventilation and graph theory are used for making computer programs when the characteristic curves of fans and temperature distribution in an underground roadway network are given.

Jan 1, 1981

By D J. Williams, S Islam

Worldwide production of black coal amounts to about 8 billion tonnes. Perhaps 20% of this annual production is washed to improve its quality, generating perhaps 250 million tonnes of coal tailings annually, generally in the form of a slurry. The coal tailings slurry is typically thickened to about 25% solids by mass prior to disposal to a tailings storage facility (TSF), and hence comprise mostly water (about 85% by volume), plus sand, silt and clay-sized mineral particles and carbonaceous material. While the tailings settle and consolidate on deposition in the storage facility, their high moisture content makes them prone to run-out should the tailings dam fail, and makes rehabilitation of the tailings difficult. Hence, it is important to understand the consolidation and shear strength of coal tailings. Laboratory consolidation testing of coal tailings from a slurry to a soil-like state has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. Laboratory vane shear testing of coal tailings produced at different gravimetric moisture contents has also been carried out. The test results have allowed a regression model to be developed relating the peak vane shear strength of the coal tailings to their gravimetric moisture content.CITATION:Islam, S and Williams, D J, 2018. Consolidation and shear strength of coal tailings slurries, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 62–71 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By H F. Galbiatti, G J. I dos Santos, A de C Zapparoli

The Grao Para and Rio Maria greenstone banded iron formations (BIFs), within the Carajas mineral province, exhibit distinct lithological and petrographic fabrics, together with pronounced differences in their surface expression, real thickness, iron grade and tonnage. These geological differences support a new model for the regional distribution of iron formations in the Carajas Mineral Province.

Jan 1, 2009

By T Dawson, B Haskins

Fatigue is it the newest buzz word or is fatigue a real phenomenon that is creating safety and organisational risk for you? There is no debate that fatigue is natural, and it affects us all, just like gravity; however, there has been much debate on the severity of its impact in the workplace. For many years the impact was not measurable, hidden out of sight and, quite frankly, written off as the infamous ‘operator error’. Over the last several years, advancements in technology have provided safety and health professionals, sleep scientists, fatigue experts and organisations with the ability to monitor and detect fatigue events in real time, as well as predict and monitor increased risk for fatigue events. Caterpillar Safety Services has assembled an extensive and exceptional set of technologies that will provide the best methods and data to measure the impact of fatigue. This paper will discuss fatigue in the workplace and review the technologies and data sets available, which will allow the reader to determine whether this risk is real or rubbish.CITATION:Haskins, B and Dawson, T, 2017. Fatigue risk in your operations – real or rubbish? It actually depends , in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By M Berry

Many mining companies routinely use benchmarking to review their operational activities and associated costs. The aim is to measure operational performance against industry norms, and identify areas where a company is performing better or worse than industry best practice. The goal is continuous improvement.In general, mine technical services, including mining geology activities, are not routinely benchmarked. There are exceptions, such as the cost of drilling per metre and the average discovery cost per unit of metal, but generally mining geology activities are only included indirectly in mining benchmarking studies.Aspects of benchmarking can play a critical role in assisting mining geologists to improve the efficiency and effectiveness of the services they provide. Industry norms for many generic mining geology functions have not been developed and measured, and therefore it is impossible to use external benchmarking to assess performance against other mines. But when used in parallel with quantifying the value of mining geology functions and establishing strategic goals for the team, key components of benchmarking methodology can provide essential feedback on how a team is performing against these strategic goals.CITATION:Berry, M, 2014. Benchmarking – does it have a role in improving the performance of mining geology?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 361–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By I Cameron

Simulation is increasingly being used to analyse mineral processing operations and explore efficiency options. Engineers that use simulation are rightly concerned with the quality and applicability of the underlying models. However, many of these models have a significant empirical component, and the best structure for this component may not be apparent. There is an opportunity to improve the quality and application range of these models by exploring potential structures for this empirical element. One approach to this problem is the use of structural optimisation, which is a formalisation of the model development process. This method searches through a family or hyper-structure of candidate models for a model that is optimal with respect to some measure of model quality. This method has been applied to the modelling of an industrial flotation circuit. The result was a model that was a significant improvement over a number of standard models reported in the literature. Structural optimisation provides a method to compare potential models in a systematic and efficient way, and hence to improve the structure of process models.

Jan 1, 1998

By G B. Douglas

Lime-based neutralisation has long been the remediation treatment of choice for acidic mine pit waters. While suited to the attenuation of acidity, lime-based neutralisation may be difficult to implement efficiently due to variation in quality and the partial loss of neutralisation efficiency due to armouring. Large volumes of gypsum-bearing sludge may also require mechanical dewatering and transfer to final voids prior to resumption of in-pit mining or closure. Thus, operational costs may be substantially higher than primary neutralisation alone. Lime production also results in large greenhouse gas (CO2) emissions.Hydrotalcites (HT) are a class of Mg-Al layered double hydroxide minerals with the composition Mg6Al2(CO3 )(OH)16.4H2O. A range of other divalent and trivalent cations may also readily substitute for Mg (eg Cu, Ni, Pb, Zn), Al (eg Fe, La, Ce) and metalloids/oxyanions (SeO42-, AsO43 -/CrO42 -, MnO4-) for CO3 into the hydrotalcite structure. A common feature of acid mine pit waters, often overlooked in assessment of potential remediation options, is the frequent predominance of divalent and trivalent cations as a consequence of partial decomposition of both ore and gangue minerals during in-pit wall rock leaching. Thus, given the presence of substantial divalent and trivalent cations in acidic mine pit waters, an opportunity exists to exploit and in effect work harmoniously with the prevailing pit water composition to form a polymetallic hydrotalcite.The utility of hydrotalcites in the remediation of acidic mine pit waters lies in their ability to incorporate a wide range of contaminants; instantaneous formation, often in a single step; simple post-treatment solute composition; rapid settling; low sludge volume; and the potential to form ore-grade precipitates potentially amendable to reprocessing to (partially) recover remediation costs. Examples of hydrotalcite formation as a method to remediate contaminated acidic mine pit waters at laboratory-scale to full-scale will be presented.CITATION:Douglas, G B, 2015. Whither lime? In situ hydrotalcite precipitation as a method of remediation for acidic mine lakes, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Diamond bearing deposits are extremely low grade and require large bulk samples to be tested to determine the grade and quality of the stones. The semi portable plants, for treatment of these bulk samples, have followed the development of commercial processes for diamond concentration. These processes included jigs and diamond pans, which have been largely supplanted by heavy media processes for primary concentration, due to the higher efficiencies in all size ranges. A number'of flowsheets including these processes are presented. The final recovery of diamonds from the bulk sample concentrates can be accomplished by rejigging, adherance to grease or by X-ray sorting. Flowsheets incorporating all the processes are presented. Two plants are described; one incorporating jigging, rejigging and hand sorting; the other using heavy media separation, and wet X-ray sorting.

Jan 1, 1984

The Goldfields extend from Norseman in the Eastern Goldfields to Marble Bar in the Pilbara; a distance of approximately 1,500 km. (Figure 1). Tailings dams are conspicuous on the relatively flat and featureless Goldfields' landscape. They impound wastes from mining and processing operations. Tailings dams interact dynamically with their environment and progressively consolidate as water is removed. Water recovery systems have been used over the last decade to improve water conservation, increase dam stability and to extend the service life of the dam. Without water recovery, dams would need to be significantly larger to permit the tailings to dry back sufficiently to support subsequent depositions. The paper reviews inter-relationships between the tailings dam and its environment and discusses water recovery systems, that are commonly used. The effectiveness of water management is illustrated by reference to seasonal water recoveries measured by Western Mining Corporation (W.M.C.) at their number 2 dam at Kambalda.

Jan 1, 1988

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

By Mahony BK

This paper discusses the major infrastructure elements required to support a typical Australian mining development. Infrastructure elements are grouped into four major types, urban planning, transportation, power and communications and water supply. The design criteria applying to individual elements within these groups are briefly discussed as well as order of magnitude cost estimates. The use of simulation models to test the capacity of existing rail networks, as well as novel sources of energy generation, are also described.

Jan 1, 1983

By I Villalba

The need to continue the development of the Ensham mine has led to blast up to 75 m to the Eastern side of a water dam in the vicinity of Ramp 23. The water dam wall is exposed to blasting over a distance of approximately 500 m. The first decision was to determine that the existing rock pillar between the Eastern side of the water dam and the blasting operations may not be less than 75 m in order to minimise the damage that the blast could generate to the dam wall. It was also necessary to define blasting practices to minimising the blast damage to the rock properties of the dam wall and to avoid adverse effects from vibration and gases generated by the detonation on structures.For this purpose analytical designs and test blasts were conducted to assess the ground vibration attenuation within the rock pillar. From this analysis, it was concluded that the best practice to reduce the rock damage was to create a zone of fractured rock adjacent to the side of each production blast. This fractured zone would create an effective filter both for vibration and for gases generated by the blast. This zone of fractured rock was created by firing two buffer rows. In terms of pattern size and powder factor the two buffer rows were designed just to generate a fractured rock zone. To date approximately 500 m have been excavated along the eastern wall of the water dam where each production blast was preceded by a Trim blast. This practice has given good results with regard to minimising the damage generated by production blasting.

Nov 8, 2011

By A L. Randriamanjatosoa, G Small, C Greet

In flotation simulation models, the effects of pulp chemistry other than pH are often ignored and reduced to particles hydrophobicity or contact angle, neither of which can be measured readily in real time in an operating plant. The flotation response of a given sulphide mineral is known to be influenced and can be improved by changing the chemical characteristics of the pulp during grinding and flotation. The on-line measurement of pulp pH, potential, dissolved oxygen, temperature and oxygen demand of a process stream was completed with the PCM® (Pulp Chemistry Monitor) developed by Magotteaux in this study. The data generated together with relevant plant operating parameters were used to construct an empirical model and simulate the metallurgical performance of the ore. The same approach was also applied to laboratory flotation tests data using various grinding media types. The flotation models better fit the actual data when the chemistry of the pulp is taken into account.CITATION:Randriamanjatosoa, A L, Greet, C and Small, G, 2018. Effects of pulp chemistry on plant and laboratory flotation modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Corbett GJ, Leach TM

The Nena Cu-Au high sulphidation deposit has formed within the Frieda River Intrusive Complex in association with a major dilatant structure. Multiple intermediate intrusives of Miocene age are localised by a splay (Frieda Fault) of the Fiak-Leonard-Schultz Thrust, a several hundred kilometre long structure, formed parallel to the accretionary prism of northern Papua New Guinea.The high sulphidation systems including Nena, crop out as narrow silica-alunite ridges extending for up to 5-6km in length within a dilational structural environment. Alteration at Mena exhibits two phases of hydro-thermal activity: an initial stage, inferred to be volatile-rich, which has produced zoned alteration; and a later phase, postulated to have been a liquid-dominated fluid, which has brecciated earlier alteration zones and deposited gangue phases as well as Cu/Au-bearinq sulphides in open spaces.

Jan 1, 1994

By Mahoney BK

The development of simulation models to reflect accurately the operations of a port and its associated transportation systems can be an expensive and time consuming process. However the complexity of such operations leaves little choice for other than simulation techniques since analytical methods are rarely appropriate. The development of suitable software has now reached the stage that these techniques can be used with confidence. Types of simulation models and their requirements are discussed together with the results from some recent applications to the planning and management of bulk terminals.

Jan 1, 1983

By S Hancock, B H. Brady, H Muhlhaus

The aims of this paper are to present the governing science, verify the performance and demonstrate the potential engineering applications of a computational simulator for in situ leach mining of non-ferrous minerals. Assuming that the target mineral is deposited either uniformly within rock matrixes (matrix-hosted) or on fracture walls (fracture-hosted), in situ leaching can be treated as reactive flow and transport in geological media (porous media for matrix-hosted ore deposits and fractured media for fracture-hosted ore deposits). Under this treatment, the processes of in situ leach mining for non-ferrous minerals can be quantified through several sets of equations and these coupled equations have been numerically solved. The computational simulator has been applied to the simulations of one-, two-, and three-dimensional in situ leaching cases. The computational simulator, together with laboratory and in situ leaching tests, can be used to:optimise the leaching chemistry; optimise the in situ scale mining operations; scale up the in situ scale test operation to a full-scale mining operation; and evaluate the post-mining environmental restoration plan.

Jan 1, 2000

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001