Search Documents

Numerical simulation by a finite element computer code has bee* used to identify key stages in the initiation of confined bulk explosive by cast primers. The simulations have been verified by comparison with experimental field measurements of shock arrival time versus distance above the primer for a relatively sensitive emulsion doped with ammonium nitrate prills. Further simulations were performed examining the effect of primer size in a relatively insensitive blend of ANFO and emulsion. Immediately above the primers, changes in shock velocity in the explosive were caused by the interactions between shocks originating from different surfaces of the cylindrical primers. At a distance up the explosive column corresponding to about one to two borehole diameters, the arrival of shock reflections off the borehole walls caused a sudden acceleration up to the confined steady state detonation velocity. The simulations reproduced experimental observations that primer size has only a weak effect on changes of shock velocity with distance for confined explosives. However, it was predicted that primer size has a strong influence on the intensity and duration of the pressure pulses that bulk explosive send into the rock surrounding the primer region.

Jan 1, 1990

A review of ground control procedures in Western Australian underground mines is presented. Geotechnical input into initial mine design and methods of ground control is rare. As a result, the frequency of unexpected rockfalls is comparatively high, with over three quarters of the mines adopting non-specialist ground control designs experiencing unexpected falls-of-ground. In contrast, mines that provide some level of specialist input into initial ground control design experience decreased rockfall frequencies.

Jan 1, 1992

By Mathew P. J

The CSIRO Division of Mineral and Process Engineering in Melbourne has been developing on-stream analysis sensors based on neutron and gamma radiation for better control of quality and process operations. This has resulted in the development of Ironscan, an on-stream analyser that measures the iron content of both lump and fine iron ore on conveyor belts. It can be mounted under existing conveyors with minimal modifications to the conveyor structure and can cope with steel cables in the belt. An interface gauge and an on-stream coal ash analyser have also been developed, both based on measurement of natural radioactivity. The interface gauge monitors the interface between liquor and mud in thickeners and washers, provided the natural radioactivity of the mud is sufficiently high to detect it above background. The natural-gamma ash gauge is a valuable addition to the Coalscan range of ash gauges. It is applicable to heavily laden coal conveyors or bins where the coal bed thickness exceeds 30 cm, and also to lightly laden conveyors, provided the coal is profiled on the conveyor.

Jan 1, 1991

By Gostylla W

The economic feasibility of controlled district cross-cut recirculation is examined in this paper with particular reference to the most important mine ventilation network parameters. An algorithm is developed to express the annual cost of recirculation which is then compared to the annual cost of conventional ventilation using the University of Queensland Experimental Mine as a case study. The concepts of resistance ratio and volumetric efficiency ratio are introduced and used to analyse the economic feasibility of controlled recirculation within a mine ventilation network.

Jan 1, 1988

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

The use of teleoperation in mining is increasing due to requirements to improve safety and reduce the number of people required to work in remote and difficult environments. We recently completed a project to develop a teleoperated control system for a rock breaker at an iron ore mine in the Pilbara region of Western Australia, with the objective of demonstrating the feasibility of remote rock breaking over long distances. This required controlling both the rock breaker and an array of pan-tilt-zoom (PTZ) cameras using joysticks. Controlling the cameras distracted operators from the primary task of controlling the rock breaker to position and fire the hammer. This lengthened task times as both the operator's attention and their hands have to swap between different control interfaces. In this paper, we present a novel design using human eye gaze as an interactive input for the remote camera control. It follows a simple and natural design principle: Whatever you look at the screen, it goes to the centre. A prototype system has been implemented by integrating computer vision based eye tracking technology, with the advantage of being real-time, robust and marker-less. We conducted a user evaluation, where users undertook a control task while obscuring the direct view of the working area and using a remote camera to transfer the live video stream as the visual feedback. Subjects were required to participate in the experiment using eye tracking camera control and traditional joystick control respectively. The statistical analysis of objective measures indicated that our novel eye tracking control significantly outperformed the joystick control. The results of the post-experimental subjective measures also revealed much higher user preference for using eye tracking control, which provides clear evidence that this design is a better interface for remote camera control in mining teleoperation settings.

May 1, 2010

IN this paper the author's intention is to convey a brief resume of the lead flotation treatment and lead flotation machines, which have replaced the May jigs and Wilfley tables at the plant of the North Broken Hill Ltd., and converted this mill into an all-flotation plant.Attention is directed to the fact that this drastic change from semi-gravity to all-flotation treatment, has been successfully accomplished without resorting to finer grinding than that previously in vogue for Wilfley table concentration, viz.: 10% to 16% plus 40-mesh I.M.M. screen.From the figures now available it is manifest that the scheme of all-flotation concentration-new as regards its successful application to Broken Hill ores is resulting in considerably higher-grade lead concentrates, and is substantially decreasing charges for labour, stores, and maintenance.The new treatment is far-reaching in its simplification of plant, as evidenced by the idle jigs and tables, and the results being obtained by North Broken Hill Ltd. may possibly influence metallurgical practice generally in Broken Hill.The outstanding features of the treatment are:(1) The coarseness, and high grade of lead concentrates obtainable.(2) The low time factor required for flotation.(3) The plant capacity, and the simplicity of its operation.(4) The low horse-power consumption.(5) The small cost for reagents used (not exceeding 3d. per ton of ore).

Jan 1, 1930

By Large RR

Precious metals in the Rosebery north-end orebody occur predominantly in sphalerite- galena-pyrite ore and to a lesser extent in massive barite mineralisation. Gold may also occur in the upper parts of pyrite-chalcopyrite ore (although this ore type is usually gold poor), in pyritic mineralisation lateral to base metal sulphide lenses and in the footwall (very patchy). Although present, remobilised precious metals do not occur in economically significant quantities. Mineralogically, silver occurs dominantly in tetrahedrite and, to a lesser extent, argen- tiferous galena. Gold occurs as electrum associated dominantly with pyrite and, to a lesser extent, tetrahedrite. Geochemical modelling suggests that silver was probably transported as a chlorocomplex, while gold was transported dominantly as a thiocomplex, although at high temperature gold was transported as a chlorocomplex.

Jan 1, 1987

The Que River Mine is a small under-ground base and precious metals mine located in north-western Tasmania. Current production rate is 220,000 tonne/yr from reserves grading 0.37% copper, 7.1% lead, 12.2% zinc, 195 g/tonne silver and 3.4 g/tonne gold.Ore is mined using longhole open stoping techniques. Cemented fill is placed in primary stopes to permit safe and efficient recovery of pillars. The operation is trackless with both shaft and decline access from surface.Ore produced is trucked 40 km by road to be sold to the Electrolytic Zinc Company of Australia Ltd., for treatment at their Rosebery concentrator.

Jan 1, 1985

A Feasibility Study to determine the future of ZC Mines was completed in mid 1987. Early in this study, which lasted two years, it was identified that significant reductions in treatment costs would result if the Zinc Corporation Concentrator was closed. All of the production from the existing two mines, The Zinc Corporation Limited (ZC) and New Broken Hill Consolidated Limited (NBHC), would then be treated in the concentrator at NBHC.After a partial upgrade of the NBHC concentrator, the ZC concentrator was finally closed and all of the equipment disposed of. This closure highlighted the need to concentrate all ore haulage in one shaft to further reduce operating costs and remove the cost of surface transport of ZC production to the improved NBHC concentrator. This paper outlines the changes that were made to improve the haulage system for ZC Mines. After a number of options were investigated, it was finally decided that the upgrade of the existing NBHC haulage shaft was the best option even though some production would be lost while the upgrade was in progress.

Jan 1, 1988

By Will D

This presentation is to outline the current practice of mechanised stoping a one-metre wide, gold bearing ore body to optimise fragmentation, minimise dilution and reduce stoping costs.Coolgardie underground operations have historically been mined using traditional shrink stope methods, but in this recent economic environment (with falling gold prices and high costs of traditional methods) it was necessary to look for alternative methods in order to reduce costs and increase productivity.Although still in a learning and refinement phase, CGNL is satisfied that it is feasible, practical and more economic to use mechanised long up-hole stope and long-hole rising methods to significantly reduce the mining cost, reduce dilution, increase safety and increase productivity three-fold compared to traditional airleg methods used throughout the Fasten Goldfields.

Jan 1, 1993

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

By Jones IO

Although small units have been in use formany years, particularly in opal mining at shallow depths, there has been little effort in the past to explore the potential of the vacuum lift system in other more demanding applications. Recent developments in Western Australia by a small number of mining companies, contractors and manufacturers have seen the design and construction of several larger, more powerful units for use in winzing, shaft sinking, hoisting and spillage removal. Some of these units have proved very successful and suggest that they could be developed for a wider range of applications and duties in future.

Jan 1, 1984

By Yates M. G, Rowlands A. T

Most geostatistical techniques applied to the estimation of ore reserves assume relatively unifonn grade and thickness within an ore deposit environment. In shear-hosted mineralisation this rarely occurs. The distribution of mineralisation is controlled by the kinematic and geometric variation within the shear zone. Although the kinematic variation is dependent primarily on the temperature (and consequently the depth) of formation of the deposit, the geometric variation appears to be relatively insensitive to this parameter. Shoot mineralisation is controlled either by the intersection of secoodary shear planes (brittle deformation) or the stretching lineation of the mylonitic fabric (ductile defonnation).Once the shear geometry is clearly identified, it is critical to review the distribution of grade and thickness of mineralisation. The practice of cutting high-grade intersections without reference to the shear model leads to underestimation of the amount of gold in the deposit. High-grade shoots may occur as pipe-shaped bodies within the system; their identification is essential for both resource estimation and mine planning purposes.

Jan 1, 1991

By Demin SS

Slow seismotectonic movements along the in-clined deep fault zone under the compressional horizontal stresses are supposed to be the prin-cipal mechanism controlling the structure and processes in the active ocean margins. Within the scope of the plane strain problem a simple 2-D geomechanical model for the evolution of an island arc system is investigated. We consider a homogeneous elastic half-plane with a shea-ring surface crack. The key element of the model is viscous interaction between the crack sides, the viscisity varying with depth. The model dif-fers from the classical steady-state mode of subduction by nonstationary creep processes on deep faults and by possibly cyclical development of the transition zone.A numerical modeling of the stress-strain state within the island arc system through time was carried out using a semianalytical approach. The results of simulation are in good agreement with geological, geophysical, and seismological data.

Jan 1, 1990

By P Griffin

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway OperationsÆ 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007

By Lawson F

Narrowly sized samples of synthetic chalcocite (Cu2S) and covellite (CuS) were leached in oxygenated acidic sulphate-chloride solutions. Chalcocite leaches via a two-stage process, the first stage being much more rapid than the second. The apparent activation energies are 42.7 kJ/mol and 68.2 kJ/mol respectively, indicating that both stages are controlled by surface chemical reactions. The leaching of covellite is also chemically rate limited with an apparent activation energy of 77.0 kJ/mol. The shrinking core model is able to be used to describe the leaching processes of both copper sulphides. Over 97% of copper present in chalcocite dissolved in 0.5 M H2SO4i0.5 M NaCl solution under one atmosphere pressure of oxygen at 85¦C in three hours from particles 36 pm in diameter while only 85% of the contained copper in covellite particles 13 pm in diameter dissolved in the same solution under the same pressure at 90¦C in six hours. About 99% of the sulphide sulphur in chalcocite was oxidised to elemental sulphur while only 90% of sulphide sulphur was converted to elemental sulphur during covellite leaching. The mechanism proposed for the two-stage leaching of chalcocite particles is as follows: in the first stage, cuprous ions rapidly diffuse to the external reaction surface where they lose electrons and go into solution as a complex cupric chloride ion CuCl'. The second leaching stage begins when covellite is formed at the external surface. Copper again goes into solution as the CuCl* ion. The mechanism for leaching synthetic covellite is similar to the second leaching stage for chalcocite except that the leaching rate of synthetic covellite is substantially lower than that of the newly formed 'covellite'. Elemental sulphur formed on the particle surface retards the dissolution processes during both chalcocite and covellite leaching. The presence of chloride ions is necessary if essentially all of the copper from chalcocite is to go into solution. When no chloride ions were present, the leaching rate of both newly formed and synthetic covellite was almost zero. The main role of chloride ions in both chalcocite and covellite leaching appears to be to disrupt the passivation film of sulphur on the particle surface.

Jan 1, 1989

A simulation of the fluid flow, minera- logical and chemical aspects of in situ leaching is being developed for application to the recovery of metals from unbroken, naturally jointed rock. The fluid flow aspect has been developed. The rock is assumed to have a double-fracture property. A major joint set is responsible for bulk flow of solution, while a minor joint set, intersecting with the major set, allows the solution to contact the reactive minerals. The two-dimensional fluid flow through the major joint set is analysed by a streamline model for a particular well pattern. The other important components of the model are described briefly.

Jan 1, 1984

The orebodies at Kambalda are complexly faulted, folded and intruded. It is realized that the ore reserve calculations will be wrong and steps are taken to minimise the errors. The calculations are a combination of computer data handling and manual input. Initially Geological Ore Reserves are calculated and then production data and experience are used to produce a Planned Mining Reserve. At all stages maximum professional judgement is incorporated. The basis of the calculation is the polygonal method of area estimation, and production reconciliations together with the style of data available indicate that it is a most suitable technique. It is also a tech- nique that is easily communicated to all levels from operators to management.

Jan 1, 1979

Revised throughput rates, as a result of current mining methods and tight controls on mine dilution, have dictated a change in metallurgical philosophy at Renison Limited. Emphasis on throughput capacity increases has altered to a reduction in circuit complexity and operating costs. Extensive surveys of the gravity and cassiterite flotation circuits led to several plant modifications between August 1989 and March 1990. The coarse and fine gravity retreatment roughing tables were by-passed, the coarse gravity retreatment roughing tables were re-commissioned, the cassiterite flotation rougher capacity expanded and the gravity regrind cyclones re-configured.

Jan 1, 1991