Search Documents

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By H Arvidson, V Chamberlain, R Marinho, B Parsons, T Rowl, M Noppé, M Mattera

With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.

May 24, 2023

By D Woolmer

Since January 2019, BHP Olympic Dam have been trialling the use of a drone based LiDAR mapping system for the purpose for surveying stope voids. This new technology utilises Simultaneous Location and Mapping (SLAM) algorithm providing positioning, stability and collision avoidance in GPS denied environments. Implementation of this system utilised underground personnel trained in the equipment’s use. The study’s intention was to evaluate the effectiveness of this equipment versus traditional surveying methods in regards to quality, safety and productivity. The trial results showed a marked improvement in the quality, productivity and personnel safety when conducting surveys. The use of the drone and LiDAR system reduced personnel and equipment requirements for surveys, thus allowing these resources to be deployed elsewhere. The technology’s simple and rapid deployment allowed multiple surveys to be conducted during a 12 hour shift, including ad-hoc work with minimal disruption to underground operations. After the drone’s initial trial, further work was conducted to utilise the Hovermap LiDAR scanner on other platforms to increase utilisation. A mounting system was created allowing the LiDAR to be mounted on a remotely operated loader or vehicle. This enabled drawpoint scans to be taken directly after production completion, resulting in faster stope close outs and drive scans for convergence monitoring. Implementation of the LiDAR system has resulted in improvements in the stope production cycle by reducing delays previously associated with data capture. The increase in the volume and quality of data has also allowed in-depth back-analysis of stopes in new mining areas to be conducted, which have driven improvements in the design process.

Mar 15, 2021

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006

By S J. Clarke, G Sieders

Double corrosion protection (DCP) rock bolts have evolved to become complicated assemblies comprising numerous components. This complexity is mainly associated with durability considerations including potential exposure to adverse groundwater conditions and ensuring separation of dissimilar metals within the bolt assembly itself.Recent progress in the construction of glass-fibre reinforced polymer (GRP) rock bolts have the potential to provide a viable alternative to conventional steel rock bolts in civil tunnelling applications. The durability of the material results in a much simpler bolt detail and permits the use of resin rather than solely cement based grouts.This paper presents the findings of the comparative structural testing of GRP bolts with conventional DCP steel bolts. The axial load performance, including stiffness, ultimate capacity and ductility of bolts are compared. Shear behaviour of bolts is considered, including durability issues associated with damage to the plastic sleeve used in DCP bolts.The paper also considers other issues which are relevant to the design of temporary and permanent rock bolts used in tunnel support, such as initial tensioning and grouting. Long-term performance, including durability and creep are also reviewed.CITATION:Clarke, S J and Sieders, G, 2014. Comparison of glass-fibre reinforced polymer rock bolts with double corrosion protection steel rock bolts for use in tunnel applications, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 237–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Connelly

Quartz deposits are common in nature but the presence of quartz suitable for yielding high purity quartz is exceedingly rare. This paper describes a test work study on producing high purity quartz (HPQ) product to meet the tight product specifications of greater than 99.97per cent, including four and even five nines, for uses including, lighting and fibre optics and modern-day high efficiency solar panels. Due to demand in renewable energy applications the market for high purity silica solar panels known for their increasing efficiency and durability is rapidly growing. Demand continues to rise for the use of high purity quartz in semiconductors, electronics, imaging and sensor markets. Microelectronic components are created by chemically fabricating wafers of semiconductors such as silicon to obtain the desired transport of electrical charge and control of the current. The production of silicon metal from high purity quartz has been designated a Strategic Mineral by the European Commission and by the US Department of Justice due to the growing significance of this metal in various industries. The subsequent processing of quartz is the key step to adding value and aiding technological advances. Overall, the high purity quartz market is a highly secretive, specialised market with increasing opportunities for stakeholders. The attempt to produce HPQ in this work was carried out using an Australian quartz ore following a typical HPQ process flow sheet. The unit processes included primary crushing, scrubbing, magnetic separation, flotation, acid leaching followed by hot chlorination. The results indicate that grinding of quartz requires specialist equipment due to the hardness and extreme abrasiveness of the ore leading to additional iron contamination in the ground ore. The critical impurities were aluminium, iron, sodium, potassium, lithium, titanium, zircon, calcium and magnesium. The chemical refining was found effective. The hot chlorination process needed to be done at 1200°C in a chlorine – hydrogen chloride gas atmosphere. The risk of any gas being released during this stage is very serious and only specialist companies should and can carry out this step. More recent studies reported many new options that appear to facilitate the production of HPQ with the requisite purities more easily, but costly equipment along with highly trained operators are required and hence unlikely to become available in standard metallurgical laboratories any time soon.

Sep 1, 2024

By A Melkumyan, F Ramos

This paper addresses the problem of prediction of grade variables over volumes (block estimation) for an autonomous mine. Resource estimation is usually concerned with the prediction of the quality of material over volumes (blocks in resource models). This problem is tackled by developing Bayesian block estimation with the Gaussian processes (GPs) framework. GPs are commonly used for nonparametric regression and classification and offer an elegant solution to deal with incomplete knowledge and information. A GP is defined by its mean and covariance function. The parameters of the covariance function can be learnt by maximising the marginal likelihood of the data. This offers a way of automating the covariance fitting process, while at the same time allowing for an assessment of how well the covariance function fits the data. Within the GP framework the calculation of the average grade over a volume can be performed using Bayesian quadrature, which treats an integral as a random variable. First, it is demonstrated that the block kriging equations in geostatistics are the same as Bayesian quadrature. Then, it is determined when closed form analytical solutions for the integrals are possible and quadrature approaches for approximations are briefly discussed.

Sep 26, 2011

Folklore suggests that oxidation is detrimental to sulfide mineral flotation, and in many instances is the reason given for values reporting in the tailing. However, while a considerable body of work examining galena oxidation is available in the literature there are very few studies that investigate the consequences of galena oxidation on its subsequent flotation in base metal sulfide ores. This work clearly demonstrates that pyrite forms a galvanic couple with galena, due to the large difference in their rest potentials, and results in accelerated oxidation of galena, particularly as the pyrite content of the ore is increased. The most obvious effect of the galvanic oxidation of galena by pyrite is the release into the system of galena oxidation products, providing an ample supply of lead ions available to activate gangue minerals, most notably of which in lead/zinc ores is sphalerite. The inadvertent activation of sphalerite by lead ions inevitably leads to the recovery of liberated sphalerite into the lead concentrate, and as a consequence a reduction in the lead concentrate grade. That is, a loss of selectivity for galena against sphalerite. If galena oxidation is excessive not only is there a considerable loss in lead concentrate grade, but also a marked decreased in lead recovery as the flotation rates of the gangue minerals increase, until they rival that of galena.

Jan 1, 2005

By J Rutter, D La Rosa, P Walters, M Scott, L Keeney

Bulk ore sorting technologies, whether surfaced based or penetrative, have seen an increased uptake by the mining industry for preconcentration application. As with all technologies, going through the technology validation process is key to de-risking the operationalisation of the technologies and to demonstrate and confirm predicted value propositions. The ability to laboratory calibrate cross-belt bulk sensors is standard practise for sensor vendors, however transitioning the technology from laboratory to real-world application is a non-trivial process. The industry has taken two main approaches to trialling and validating bulk sensing technologies in operational environments, namely:  Construct an off-line pilot facility at scale, or  Install bulk sensing systems on production conveyors Each of these two approaches have significant advantages and disadvantages and require different experimental design programs and analysis methodologies. Consideration of material movement, heterogeneity degradation, logistical requirements, and financial investment all factor into which approach is most suitable for an evaluation scenario. CRC ORE in partnership with mining companies, have conducted several bulk sensor pilot trials utilising different sensor technologies employing each of the two main approaches outlined above. This paper describes the challenges faced, learnings obtained and outlines a position on how to transition bulk sensing technologies from the laboratory into the operating environment. The case studies presented cover a range of commodity types in both open pit and underground operations.

Nov 10, 2020

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By H Bruyn, K Ehrig, V Liebezeit, A Robertson, M Smith, D Grant

"The Olympic Dam geometallurgy program has generated a large quantity of data that has been used to create a geometallurgically enabled block model. An ongoing challenge is to convert data into usable information and embed geometallurgical practices into resource model development and mine planning to assist with the identification of opportunities to maximise value.This paper will discuss the methods used to disseminate geometallurgical information throughout the planning life cycle including data extraction methods from the geometallurgy acQuire database, and the inclusion of a geometallurgy module in the Olympic Dam Stope Reserves database. The use of geometallurgical information in short-, medium- and long-term mine design and scheduling, including its use in grade descriptor development and stope value assessment tools will also be presented. The detail of development of specific geometallurgical models is outside the scope of this paper.At Olympic Dam, the incorporation of geometallurgical capability within the long-term planning team, traditionally the domain of mining engineers, has proved essential in broadening the base of geometallurgical knowledge as well as focusing geometallurgy resources on value-adding areas while providing a holistic risk based long-term plan.CITATION:Liebezeit, V, Ehrig, K, Robertson, A, Grant, D, Smith, M and Bruyn, H, 2016. Embedding Geometallurgy into Mine Planning Practices – Practical Examples at Olympic Dam, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 135–144 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C Fong

Compliance Planning is an active approach to ensure mining operations align more closely to their longer-term plans. Through Compliance Planning, operations can not only measure their performance on intervals as short as intra-shift, but they can then apply corrective measures to ensure they remain as close as possible to the plans. Compliance Planning targets short-term and execution level teams, as these are the shortest duration planning divisions commonly found in mining operations. Compliance Planning combines live information with intelligent planning capabilities to provide a framework that enables mining operations to realise a significant improvement in reconciliation of plan to actual movements.

Jun 22, 2022

Last September, when I was asked to prepare this paper, I was told the subject was "mining," a broad subject indeed! Rather than choose one of the many important technical and economic details which characterize mining today, I turned to a subject which fas- cinates me: mining's image. If we are to survive and prosper into the twenty-first century, and if industry and society are to continue enjoying the material benefits which flow from mining, we must address the melancholy fact that the general public at best does not understand mining, and at worst does not believe it is needed or deserves to continue. While my point of view is largely that of an American mining executive, I would hasten to point out that Homestake has participated in Australian mining for over three decades, and our subsidiary, Homestake Gold of Australia Limited, is now a major producer in this "lucky country." Does society need a viable minerals and metals industry? The answer is obviously "yes," so the challenge is to change some minds: not just those of the amorphous "public," but on a focussed basis targeting journalists, educators, TV commentators, politicians and opinion makers of all stripes (I thought of using "rifle shot" instead of focussed but thought that might be misconstrued). Along the way we miners must also look deeply into ourselves, our attitudes towards the society in which we function, and our willing- ness to change as well as to seek change in others. How did we become such bad guys? More than a century ago mining was not just accepted, it was even romanticised. In America, we had altered the time-honored concept of "Crown" lands into public lands made easily available to settlers pushing back the frontier. Miners even preceded the farmers and stockmen in what was perceived as nation-building, although by the 1890s there was a growing interest in conservation, especially the protection and management of forests and national parks. Even though emphasis was shifting toward government stewardship and away from trans- fer of public lands to private ownership, homesteading and mining were clearly recognised as valid uses requiring not just access, but security of tenure. Indeed, conservation as it was then understood implied management of the public domain as well as its protection. Initially this was no great problem to the U.S. mining industry, but as the nation grew and competing land uses became more important, conflicts began to appear, first over water rights and later over air quality and destructive mining practices. But these were local disputes rather than national issues, and two World Wars, the Great Depression and post-war reconstruction lulled our industry into thinking that nothing had really changed. After the storm began to break in the 1960s, the mining industry found itself confronted by a growing maze of complex and costly laws and regulations. It took us longer than it should have to realise that, in facing this challenge, we seemed to have lost the understanding and support of many of our legislators and a majority of the general public. For over 20 years now, since the first Earth Day in 1970, the U.S. Mining

Jan 1, 1991

By K Voigt, B Bolton, C Rumble

The Ok Tedi copper and gold mine is owned and operated by Ok Tedi Mining Limited (OTML) and is located in the Star Mountains of the Western Province of Papua New Guinea. Waste materials (both sulfidic and carbonate materials) from mining operations, comprising 55 Mt of waste rock and 31 Mt of tailings per annum, are discharged into the headwaters of mine area creeks where erosion and sediment transport carries significant proportions of the total waste into the Ok Tedi and Fly River systems. The tailings are potentially acid forming (PAF) while the waste rock has been strongly acid consuming with an excess of acid neutralising capacity (ANC) due to the high proportion of limestone waste. Tailings and waste rock are eroded into the river system and transported to the lower Ok Tedi and floodplains where deposition takes place. Because of concern due to vegetation die back, a dredging operation commenced in March 1998 to remove the sand fraction from the main river channel. OTML identified a potential future ARD risk from the stockpiled sands due to reduce limestone production at the mine and sulfide/carbonate mineral segregation in the river system and in the dredge sand stockpiles. This paper describes the structure and framework of an empirical model developed to assist OTML in planning ongoing mining operations to control ARD. Modelling identified the need to provide additional mined limestone to prevent future ARD generation from material deposited in the mine area creeks. With the additional limestone, the ARD risk in waste rock storage areas and in the Ok Tedi and Fly River sediments is predicted to remain low due to the combined effects of high ANC, high alkalinity of natural waters and high moisture contents (mostly fully water saturated). However, monitoring and modelling indicate that the ARD risk from the stockpiled sands will increase substantially during the remaining years of the operation. OTML have initiated programs to identify and evaluate options to mitigate this risk.

Jan 1, 2003

By P Ramsaywok

The use of saline water for mineral beneficiation in arid regions is general practice and also the case with Exxaro Namakwa Sands, situated on the west coast of South Africa. Although it is ‘cost effective’ to use sea water for mineral beneficiation, downstream process separation efficiencies may be negatively affected. This is more specific to surface dependent separation techniques such as electrostatic and high tension (HT) separation. If minimal fresh water is available then, proper washing is often neglected. Salt crystals can form on particle surfaces during the drying process before electrostatic separation.This paper describes a study that has been conducted to determine the effect of upfront salt water processing on downstream electrostatic/HT separation. The study indicated that minor quantities of salt can cause the separation efficiency to decrease substantially.

Oct 5, 2011

By B Hayes

The Ambuklao and Binga Rehabilitation Project is a 175 MW hydro power project currently under construction across dual sites in the north region of Luzon Island, Philippines. When it was built in 1956, the Ambuklao Dam harnessed the second largest hydro-electric reservoir in Asia. However, due to landslide erosion and prolonged silt infiltration caused by an earthquake in 1990, the power plant has been rendered inoperable since 1999.To bring the power generating facility back to life, the project scope entails the rehabilitation and construction of civil structures, shafts and tunnels. A major component of these works is the decommissioning of a section of the seven metre diameter headrace tunnel by installing a concrete plug. The headrace tunnel is part of a closed waterway system that connects the dam via a shaft, exhibiting a hydrostatic pressure of 13 bar (1300 kPa) at the location of the new tunnel plug. In addition, the power station ball valves have seized ajar and the damaged intake riser is unsafe toaccess thereby requiring the plugging operation to be carried out under live flowing conditions.Working under hydrostatic pressure and live conditions, the headrace plug will be an underwater tremie pour operation that includes drilling and concrete injection through blow out preventer caissons installed in the floor of an underground chamber above the tunnel. The purpose of this paper is to describe the key engineering and planning components involved in this operation including pre- and post-grouting, chamber crane, sonar, local water compensation, jet flushing, drilling, caisson installation, and concrete design, production, delivery and placement. The success of this task rests on the strategic preparation and operational management of risk and safety in a challenging rural environment.

Mar 8, 2011

By S Talu, E Savage, P Sturm, A van As

It is estimated that substandard ground support installations and elements cost the Rio Tinto Copper Group millions of dollars between 2000 and 2014. These issues have also created significant safety and financial risks in Rio Tinto mines. As a result, Rio Tinto Copper has developed CaveCAD, an integrated system to collect, store and analyse all ground support-related data. The CaveCAD system stores geotechnical data and has the ability to automatically import data, collect data through tablet applications, report processed/analysed data and present this data through 3D visualisation software.The CaveCAD Ground Support module closes the design–implementation–verification loop by providing a method of verifying the compliance of all installed ground support, recording manufacturer specifications, recording quality control test compliance and rectifying any non-conformant areas. The module uses innovative technology to create value through cost saving, safety improvements and data collection efficiency. Cost savings will be achieved by a decreased need for excavation rehabilitation, less ‘waste’ due to faulty installation and quality assurance checks reducing the likelihood of substandard support units being used. Data collection will be improved through the use of a mobile tablet application that can be used underground in ‘off-line’ environments.CITATION:Savage, E, Talu, S, Sturm, P and Van As, A, 2016. Development and implementation of the CaveCAD ground support module for cost and safety improvements in block cave mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 769–772 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

The creation of an accurate and precise enough database requires the collection of many representative samples, subsampling and assaying them without destroying their integrity. The selection and implementation of sampling protocols often lead to severe difficulties, making the unaware practitioner vulnerable to massive exploration, feasibility and operating failures. Therefore, there is no substitute for a good understanding of the Theory of Sampling (TOS). Either because of ignorance, or because of short-term economic reasons, failure to comply with many stringent conditions can be devastating for the validity of a feasibility study, leading to false evaluations, to the abandonment of a viable property, or to the exploitation of one that is not profitable. All these failures have something in common: insufficient duplicate sampling, subsampling and assaying were performed; very important, preliminary heterogeneity tests were never performed; for short-term economic reasons, poor sampling and subsampling protocols were selected, second-class sampling systems and weightometers were installed and poor preventive maintenance and cleaning were implemented;and sampling experts were called only when the project was obviously in trouble. The conclusion is clear: in due time, iterative auditing of sampling practices is an insurance policy against massive financial losses for the company involved. A complete, comprehensive 100 point checklist of sampling Quality Assurance and Quality Control is provided, so critically important details to ensure success are not forgotten.

Mar 1, 2010

By K Watters

API Management Pty Ltd (API) is currently developing the West Pilbara Iron Project (the ‘Project’). The Project is a substantial greenfi elds mining and infrastructure development proposed for the west Pilbara region of Western Australia. The Project will establish API as a new and independent supplier of direct shipped iron ore. API manages the Australian Premium Iron Joint Venture (APIJV) on behalf of joint venture participants Aquila Resources Ltd and American Metals and Coal International Inc. The APIJV was formed in February 2005 with the objective of developing a long-term iron ore export operation in the west Pilbara region.Development of Stage 1 comprises a 30 million tonne per annum (Mt/a) channel iron deposit (CID) operation scheduled to commence in the second half of 2014 subject to approvals. JORC compliant CID resources total nearly 700 million tonnes and the Stage 1 mining area comprises eight iron ore deposits located between 30 km and 85 km south of Pannawonica. Run-of-mine ore from the eight deposits is transported to a central processing facility for crushing, screening and blending into a sinter fines product, which API has named West Pilbara Fines or WPF. Construction of a 282 km main line heavy haulage railway from the Stage 1 mining area to the proposed greenfields multi-user port at Anketell Point near Wickham, is capable of accommodating large Capesize bulk carriers and providing export facilities for other third parties. Capital investment in the order of $A6 billion includes essential support infrastructure including power, water, accommodation, roads and an airport at the mine.A feasibility study for the development of the Stage 1 mine, rail and port infrastructure has been completed along with environmental surveys of the mine, rail and port areas with Public Environmental Reviews (PERs) for each submitted for public review by end 2010. Consultation and cooperation with various stakeholders of the Project areas, and early engagement with traditional owners of the respective areas has commenced. Various sampling and metallurgical characterisation programs combined with independent institute and steel mill based testing have confirmed the positive sintering characteristics of WPF ore, which is higher in alumina (3.37 per cent) than typical Pilbara ores. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011