Search Documents

By R Hughes

"Spring Creek Mine uses high pressure water to extract the thick Main seam in the Upper Rewanuicoal measures. The extraction method results in the creation of large voids which collapsespontaneously. This can result in the displacement of large volumes of methane, which may create a signifi cant hazard if not correctly managed. A system of automatic dilution doors is employed to mitigate this risk. This paper describes the evolution of the system and gives some examples of its eff ectiveness."

Jun 1, 2012

Cannington Mine is an underground, hard rock, metalliferous mine located in North-Western Queensland, Australia. Weld mesh is installed to prevent the failure of rock from between the installed reinforcement elements. Corrosion reduces the capacity and life expectancy of mesh and presents a real hazard to underground personnel and equipment as it reduces the effectiveness of the support system. Corrosion influences the economics of the mining operation through the need to conduct rehabilitation of the ground support which involves re-installing new mesh or shotcreting over the affected mesh to protect it from further corrosion. The requirement for rehabilitation is determined by the geotechnical engineer based on an individual visual assessment with little or no engineering input. It was identified that a more quantitative method was required that considered the safety and economic risks involved. A project was undertaken to develop a simple method to evaluate corroded mesh and to provide selection criteria for rehabilitation. A weld mesh corrosion classification has been developed that relates the average wire diameter of corroded mesh to the remaining capacity of the mesh. Accompanying selection criteria provides recommendations as to when rehabilitation may be required based on the estimated residual mesh capacity, the remaining development life, and the level of personnel exposure.

Nov 25, 2010

It is hypothesised that increasing the number of loading passes will produce a reduced range of truck payload outcomes compared with four-pass loading. The paper provides analysis to support this hypothesis. It is shown that, hypothetically, loading trucks with five or more passes will result in reduced tendency for overloading and reduced confidence interval for truck payloads that increase the confidence level of containing high end payloads within safe and commercially acceptable limits. Furthermore, increased number of passes provides for more precise bucket load spotting and so improves distribution of payloads within truck bodies. Truck-loading issues examined by the paper include: Improvement in life of driveline components and tyres. Generally tyre costs are relatively moderate; but tyres tend to become an increasingly sensitive performance/cost component as truck scale increases; Reduction of site severity fects flowing on to suspensions, truck frames and structural components generally with potential for reduced long-term repair costs; Less physical body damage due to smaller load increments; Reduced risk of non-compliance with payload limitations for safe braking standards; Increase in loading cycle times tend to increase with scale of loading machinery within the limits of a specific type of equipment (ie rope shovels or hydraulic shovels). Production increase with increased bucket capacity is, to a degree, offset by slower loading cycle times. This is particularly pronounced with front-end loaders but tends to be less noticeable with hydraulic excavators/shovels and electric rope shovels. Decrease in loading time, as a proportion of total truck-cycle time as open pits deepen and dump reaches increase. The production and cost benefits of four-pass loading tend to diminish as truck cycle times increase. The paper also discusses the implications for loading-equipment philosophy to satisfy the future needs of the industry. Cost benefits from upscaling tend to diminish as truck scale increases, so increasing management diligence and close monitoring are required to ensure that expected outcomes are realised. These truck-loading issues have been researched to assess the benefits positive or negative) of four-pass loading in practical scenarios. An attempt is made to determine whether four-pass loading is a æmust-haveÆ or merely a æmythÆ.

Jan 1, 2003

Madison Enterprises Corp. and Matu Mining are currently ex- ploring the Mt. Kare property in Papua New Guinea. The Mt. Kare gold prospect has had a short but very active history, since the first discovery of gold in the area in 1986 the property has sccn: a 3 year gold rush during which 10,000 alluvial miners re

Jan 1, 1997

By Kobe HW, Balance PF, Black PM, Sporli KB, Smith IEM, Locke CA

The Hauraki Goldfield consists of a large number of volcanic-associated epithermal gold deposits within the Coromandel Volcanic Zone (CVZ), North Island , New Zealand; it is the most accessible and most studied of the Southwest Pacific gold regions. The deposits occur generally as steeply dipping quartz veins and breccia sheets in faults and fractures.From a tectonic perspective, the CVZ is generally considered a Neogene convergent volcanic arc constructed under an extensional tectonic regime; the common tectonic setting for epithermal mineralisation. The gold deposits are mostly hosted in subaerial andesitic arc-type volcanic rocks. Temporally, however, mineralisation is associated with rhyolitic rocks of a bimodal volcanic suite that may represent a back-arc environment. Rifting and calderas may be important components of the latter regime, but this is not yet clear; the general structural framework controlling the location of CVZ gold deposits remains poorly understood. Geophysics, particularly aeromagnetics, has a role in mapping regional fault patterns in the CVZ

Jan 1, 1990

The process of hydraulic transport through pipelines, world-wide well known for the trans- port of fine-grain solids is also being used to a greater extent in mining for the handling of 1rimarily coarse-grain solid - water mixtures r the removal of, for instance Coal and waste mixtures after coal winning rising hydraulic monitors, lings for backfilling underground and :her tailings and flotation waste to A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining P',search Company) in Essen-Kray, GFR, to ¦urther improve this technology. The unit was :fanned and built by Krupp Industrie- and +hibau of Duisburg in cooperation with i r

Jan 1, 1980

Recent and on-going studies on the leaching of gold, the properties and activity of carbon, developments in the elution of gold from carbon, and methods of recovering gold from solution are reviewed. Emphasis is placed on Australian contributions, and their impact on gold metallurgy. Consideration is given to the future development of selective solvent extractants, ion exchange resins or alternative reagents for cyanide.

Jan 1, 1987

The Favona Underground Project is located approximately two kilometres east of Martha Mine Open Pit in Waihi, 150 km south east of Auckland, New Zealand.   The underground reserve of 354 koz Au contained in resources of almost 600 koz lies within 600 m of the existing process plant presenting an attractive development target in a challenging environment.   The Martha Mine Open Pit is surrounded by urban housing on the north western edge of Waihi township and the Favona Underground abuts residences on the eastern edge of town. Environmental, community and social licence aspects influence project strategies as the new underground mine extends mining in a town that is planning for closure of current open pit operations in late 2006.   The Favona Underground Project has successfully passed through a detailed feasibility study, the third stage of the five stage Newmont project appraisal system. Methodologies used in the feasibility study and parallel permitting draw on a high level of stakeholder involvement to streamline the development and permitting phases.   This paper discusses the project appraisal process and design innovation required for developing an underground mine adjacent to town.

Jan 1, 2004

Peko Mines, a Division of Peko-Wallsend Operations Limited (PWOL) has operated several small underground mines in the Tennant Creek district of the Northern Territory supplying ore to a central treatment plant. The Argo Mine is the most recently developed by Peko Mines. A magnetic anomaly was identified from low level airborne magnetics in 1960 and drilling, which commenced on the site in 1969, was halted in 1974 and resumed in 1980 following the rise in the price of gold. By mid 1983 a resource of + 200 000 tonnes of 12 g/tonne Au had been outlined and a decision to develop the resource was taken following the drilling of three further diamond drill holes which did not significantly alter the value of the resource. The small size of the orebody could not support the full capital cost of two shafts and a single entry mine plan was developed to extract the ore at a rate of 15 000 tonnes per month and to provide all the safety features, ventilation systems and services of a two shaft mine. In December 1983 a contract was let to Allied Constructions Pty. Limited (Allied) to sink and equip a 4.8m shaft to a depth of 410m and to convert the headframe and winder, which are leased for the life of the mine by PWOL from Allied, from a sinking to a production configuration. Shaft equipment designed by Hardcastle & Richards Pty. Ltd. (H & R) in conjunction with PWOL includes a skip/cage, counter- weight, and an auxiliary cage on rope guides, a sealed ladderway and exhaust air ducts.

Jan 1, 1986

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

By Lunarzewski L

Gas problems, largely instantaneous outbursts of coal and gas, arose in the early days of coal mining in Australia, leading to attempts at predrainage often including destressing. With deeper mining and new gassy areas being mined, gas problems have increased. This has led to more research, such as into coal-gas relationships, and more practical trials into seam gas drainage in both the Sydney and Bowen basins. Predrainage techniques have been devised to suit the special Australian geological conditions and to take into account the erratic occurrence of CO, (nearly 100 per cent in some cases) in the seam gas. Better mining methods and other improvements are continuing. The introduction of post-drainage has been simplified by the adaptation of long established overseas techniques and equipment.Utilisation of seam gases in Australia is complicated by the presence of CO, but even with pure CH. little has been done.Seam gas drainage has some disadvantages such as the need for, and the dangers of, complex and rigorously controlled plant. Also drained coal becomes harder and dustier.

Jan 1, 1985

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

Shear strength testing of rock discontinuity surfaces has been undertaken at a considerable number of open pit gold mining operations in Western Australia, as part of geotechnical studies of pit wall stability. These mining operations are located in geological settings that are typified by highly weathered and/or chemically altered rocks that contain significant structural fabric in which accurate and representative measurement of shear strength is essential.Little of the published rock discontinuity shear test work and back-analysis of failures has been conducted on weathered discontinuity surfaces, at low normal stress levels which are comparable to Western Australian conditions. Available shear strength data are reviewed and the following aspects of shear strength testing are considered:ò the need for shear strength test work and the amount of testing required;ò review of laboratory testing methods and the quality of the results; ò presentation of the test results;ò discussion of the shear strength failure criteria; ò interpretation of the test results;ò summary of test results for a variety of rock types, degree of weathering and discontinuity surface conditions;ò a review of laboratory and field shear strength data to illustrate the amount of variability that can occur; andò a monitoring strategy is proposed to manage the uncertainty associated with discontinuity shear strength.

Jan 1, 1992

By S Mitra, T Singh, D O’Dea, T Honeyands

Permeability and air flow rate in the bed during iron ore sintering is crucial to controlling the sinter quality and productivity of a sinter plant due to its influence on the flame front speed. In the present work, the permeability of the bed during sintering was analysed by means of measured pressure drop and temperature at multiple points in the bed during sintering. Three different zones were categorised, ie humidified (green) bed, region of maximum resistance (high temperature zone) based on temperature, and sintered bed. Previous work has shown that the maximum pressure drop during sintering was due to several concurrent physico-chemical processes including dehumidification, calcination of fluxes, dehydroxylation of goethite, combustion of coke and melting of granules (>1200°C). To quantify the effect of the different process, sintering experiments were conducted in a milli-pot (diameter 53 mm, height 400 mm) with pressure and temperature measured at same location in bed. The milli-pot was fitted with four equidistant (80 mm apart) taps. Overall, five sections in the milli-pot were analysed for pressure drop at different times during sintering. It was found that in region of maximum resistance, coke combustion and flux calcination were highest contributors with ~35 per cent of the pressure drop when compared to other processes like de-humidification and goethite dehydroxylation which contributed to ~20 per cent and 25 per cent each respectively. The pressure drop contribution of the coke combustion region increased with increasing coke addition rate.

Nov 8, 2021

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

By W Wu

The prospect of discrete element modelling (DEM) being used as an everyday design tool for transfer chutes in the iron ore mining industry is becoming more and more probable. However, much care needs to be taken to ensure accurate results are obtained. Whilst there are many publications in industry portraying the potential of DEM, there is little evidence of where it has been validated against a real set of experimental results. The purpose of this investigation was to gauge whether the incorporation of the physical properties of a specific bulk material at the DEM pre-processing stage can yield visually and numerically accurate simulations for a simple flow case. Effects such as irregular particle shapes, varying frictional properties and coefficients of restitution, all found through experimentation were investigated. Video analysis was used to compare simulations to real flow cases. It was found the most critical attributes in determining the accuracy of the simulations were particle shape and wall friction. Keeping the particle-to-wall friction factor constant was not sufficient to describe the flow accurately. But by introducing the varying effects of wall friction with consolidation stress, the correct results were simulated.

Jan 1, 2007

By Cameron A

In recent years there have been significant developments in the tech- nology available for blast monitoring, analysis and simulation. Progress in these areas has been achieved through research conducted by explo- sives manufacturers and independent research groups from universities and mining companies. Miners are increasingly keen to exploit this tech- nology to help them design blasts which make optimum use of explo- sives to produce easily excavated muckpiles for the minimum possible cost. The art of blast design in the future will increasingly depend on an adequate understanding of the nature of the rock mass, the perfor- mance of explosives and the characteristics required of the muckpile to suit the chosen excavation machinery. Despite recent advances in blast simulation and the prediction of blasting performance, the best way to determine how a particular explosive will function relative to other explosives is to conduct properly designed and monitored field trials. This paper discusses recent work at Mount Thorley Colliery which demonstrates that field blasting trials can be monitored and analysed to provide quantitative data on the relative performance of bulk explosives. Techniques used in the trials included the sampling and analysis of explo- sives, insitu measurement of VOD, monitoring of near and far field vibra- tions, high speed and still photography and survey measurement of muckpiles. These techniques provided data for the analysis of throw, swell, fragmentation and burden movement together with data on the consistency and robustness of different explosive products. The blasting trials allowed both the shock and heave energy of various explosives to be observed in the field and led to the derivation of design rules for the use of differ- ent explosives at the mine.

Jan 1, 1988

P.IISTRACTThe Pacific Rim is advantaged by the uniqueness and diversity of its geological features. Why then is geology given so little regard in the education systems of the countries of this region? Not that these countries differ greatly from those in other parts of the world. Papers presented during the Precollege Geoscience Education session at the 28th International Geological Congress (28th IGC) held in Washington, July, 1989, indicated strongly that the problem is universal. There is a marked decline in interest in the Earth sciences and many nations are looking towards methods that might change this trend. Problems affecting geological education include the lack of purpose and direction, its obsolete curricula and the difficulty in attracting gifted students.The world-wide plight of geology comes at the very time when it should be fundamental to a public understanding of the global effect of human population pressure. There is a universal awareness of "the environment" but very little awareness of the science that has supplied most of the data. Geology, as the science of the Earth, is of paramount importance to an understanding of our life on this planet, particularly in its role as the source of our every need.

Jan 1, 1990

By Kennerley P

A significant part of the reserves of the Southern Coalfield lie beneath major water storages and their impounding dam structures. One of the functions of the NSW Government's Dams Safety Committee is to specify the particular mine layouts which can be used beneath the stored waters according to certain guidelines. A study was made of examples of the two different methods of extraction used under the stored waters as proposed by the mining company according to the guidelines and approved by the Dams Safety Committee. Using both pillar monitoring and mathematical modelling approaches it was shown that the recovery of coal from these layouts could be improved while still ensuring the long term stability of both the underground support pillars and the body of the strata. The integrity of the water storages and their impounding structures would therefore not be Affected.

Jan 1, 1986

By M Byrne, P Newman, M Lindqvist

SomincorÆs Neves Corvo Mine, one of the largest copper producers in Europe, is currently constructing a paste backfill plant in order to replace cemented rockfill in its bench and fill stopes and possibly replace hydraulic sandfill in the drift and fill stopes. A 250 m flow loop was constructed at the mine and the flow properties of various paste blends were investigated. Cycloned tailings and total tailings were both pumped successfully as pastes and were also combined with waste rock for additional testing. The pressure losses in 102 mm and 154 mm diameter pipeline were recorded at flowrates up to 60 m3/hr and are presented at slumps from 120 mm to 250 mm. The data showed the sensitivity of paste mixtures to slight changes in consistency, confirming the need for accurate control during paste production and distribution. The flow results clearly showed the different paste behaviour between cycloned and total tailings pastes and the change in properties at low and high slumps. In addition to pressure loss data, strength testing was done on 38 mm and 82 mm diameter samples. Further strength testing is ongoing at the mine using fly ash as a supplement to cement, reducing the overall binder cost. Preliminary engineering for the underground distribution system is briefly discussed, with reference to the siting of the plant. The Neves Corvo Mine is particularly shallow and alternative methods to pumping were sought in order to ensure sufficient hydraulic head for underground distribution. The comparison of options had to take into account the capital and operating costs, the operation of the plant and the impact on the future expansion of paste fill utilisation at Neves Corvo.

Jan 1, 1998