Search Documents

CONTENTSSummaryIntroductionGeographical and Geological Outline of the RegionGrowth of the Mining IndustryTable 1: Production StatisticsGeneral GeologyRecent Alluvium and River GravelsSambeto SeriesMudstone and Basalt ContactVatukoula SeriesIntrusivesStructureGeologic HistoryLodesTable 2: Principal Lodes and Their OrebodiesMineral Assemblage and ParagenesisOre Shoots and Their ControlEmperor MineLoloma MineDolphin MineExplorationConclusionAcknowledgmentReferencesSUMMARYThe Tavua Goldfield was found in 1932 within a basin, both topographical and structural, near the sea on the north side of Viti Levu, Fiji, and has produced over £13,000,000 (Fijian) worth of gold and silver from the three mines...

Jan 1, 1953

Cable bolts have been used extensively in the development of the footwall of the Mt Whaleback Mine as a part of the ground improvement program since 1986. High tensile seven wire stress relieved steel strand similar to that used in pre-stressed concrete and grouted in place with sulphate resistant cement have been employed for rock-mass reinforcement.Most of the footwall is developed in Mt McRae Shale which contains a 20 m thick pyritic shale layer 14 m below the ore/waste contact. Due to extensive folding of the footwall rocks, the pyritic shale layer regularly occurs on, or close to the pit slope. Rain water run-off seeping through pyritic shale becomes acidic to the extent where its pH value can be as low as 1.5.

Jan 1, 1992

By Lauha E. A

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike subdistrict, there are seven major deposits; Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the subdistrict are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Bamck Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post, and Deep Star occur both on Barrick and Newmont Property.

Jan 1, 1991

By Bingwen Z, Fengyi K

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover- caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By Mosusu N

Geothermal anomalies of different types occur within distinct geological/structural settings in Papua New Guinea. According to R.F. Herring, geothermal occurrences in Papua New Guinea can be classified into two types, those related to vulcanism (Lihir, Rabaul and other series of islands along the volcanic arc) and those resulting from a regional heat flow probably caused by radiogenic sources, for instance those in the Wau/Bulolo area. The manifestation of this potential source of energy generally coincides with either converging or diverging tectonic plate boundaries. Previous inventories on thermal waters were carried out by vulcanologists from the Rabaul Observatory in the early 1960s. However, these studies rarely included chemical analyses of water and gas emissions and the investigations were carried out in an ad hoc manner, generally as a secondary activity. The most recent investigation on thermal waters was conducted on Lihir Island in connection with the development of the open pit gold mine. These studies included detailed exploratory drilling to a maximum depth of 730 m, and a water chemistry isotopic sampling and analysis programme. The hydrothermal waters were not considered as an energy source but as a hazard during the development stage of the mine. Nevertheless, the geothermal anomaly observed at Lihir includes hot springs emerging along the coastal zones with temperatures that approach 100¦C, steam, and thermal borehole waters with temperatures that exceed 200¦C. Chemical analysis results of thermal fluids from Rabaul, Talasea and other areas in Papua New Guinea generally show high total dissolved solids and low pH. In contrast, recent results from the deepest and hottest thermal source at Lihir shows a neutral pH, a Na-CI-SO4 composition and temperatures above 200¦C. Despite the concentration of chloride being similar to that of sea water, other chemical results and stable hydrogen and oxygen isotopic compositions of thermal fluids imply the source to be mixture of local meteoric water and deep thermal water rather than sea water. Results of geothermal modelling suggests that the total geothermal uptlow is equivalent to 54 MW.

Jan 1, 1997

A review is presented of techniques cur- rently in use, or being developed, to enable the determination of virgin rock stress at consid- erable depth (> 1000 m) from small diameter sur- face drill holes (

Jan 1, 1975

SITUATED in the county of Manchcster, in Northern Eyre's Peninsula, the Iron Knob ore-deposits form the basis of the industry. These deposits are connected by the Iron Knob tramway to the port of Whyalla, aal miles distant, on the western shore of Speneer Gulf,and to-day another tramway is under construction to link up with the same port, a second group of iron ore leases known as Iron Baron, which is situated 18 miles south of Iron Knob. Fig. 1 indicates the geographical relationship of these three places, Iron Knob, Iron Baron, and Whyalla, which together comprise this field of the company's activities.

Jan 1, 1930

Following unprecedented high market prices for tin and gold in 1980, significant advances in both mining technology and geological knowledge took place in northeast Queensland. These led to a rapid growth in mining activity. Production of these traditional metals reached levels comparable to those of the heyday of mining activity at the turn of the century.Although tin and tungsten prices have since collapsed, the geological knowledge gained and significant discoveries made during the boom, have created a potential for mine development when prices rise again. For other discoveries which are not workable because of treatment problems, future technological advances are required to raise their potential.

Jan 1, 1990

By M Ewart

The securing of a reliable water supply for a prospective mine in the North West Queensland Mineral Province is usually one of the most influential factors in determining the mine's feasibility. The Ernest Henry Mine required a reliable water supply to serve a demand estimated at feasibility stage to be up to 20 ML/day. Numerous options were considered before a decision was made to construct a 113 km long pipeline from Lake Julius as this was the most cost effective, reliable source of supply. The North West Queensland Water Pipeline is a multi-user, Queensland government funded project initially supplying up to 7000 ML/year of water from Lake Julius to Ernest Henry Mine, with provision made for expansion to serve future users in the region. This paper discusses the history of the pipelineÆs development, together with a summary of the scheme's design features. Environmental and licensing requirements, construction and operational issues are also discussed.

Jan 1, 1998

By De Jong HJ

During the forthcoming reline of No.3 Blast Furnace at the Newcastle Steelworks of the Broken Hill Proprietary Co. Ltd., facilities for the screening and weighing o' coke will be installed. The equipment is needed to optimise the sizing and the quantity of coke immediately prior to it being charged to the furnace. Up till the time the furnace was blown out in November, 1982, coke was charged to the furnace by volume, ie by skip fulls only. This resulted in variation to the ore/coke ratio charged due to bulk density changes and erratic skip filling levels. This in turn affects the heat balance of the furnace and causes fluctuations in hot metal chemistry and temperature. A coke rate penalty has to be paid also. Coke layer thickness in the furnace burden cannot be controlled closely, resulting in loss of control over gas distribution in the furnace. A grizzly type screen was incorporated in the skip loading chute but this ineffective method left a great amount of fines with the coke being charged to the furnace. Furnace permeability was therefore reduced, particularly in the hearth.

Jan 1, 1984

By O Tiili, A Dixon

Many minerals processing plants need to have greater efficiency in current times and optimise their process performance in order to maintain high profitability. This is even more so in the current economic climate. In the case of large flotation cells, such as TankCell«-300 with over 300 m3 active capacity, ensuring consistent operation and optimal flotation conditions is particularly critical, given the high impact on overall process and throughput of such cells. As there are fewer cells to control and monitor, there is also a lower initial capital cost for instrumentation - the requirements, however, are higher. Despite such compelling reasons, instrumentation and basic control in flotation cells has not changed much in recent years. The standard is still to use traditional feedback (PI algorithm) controls for slurry level and flotation air. A new advanced instrumentation and control package for large flotation cells has recently been developed by Outotec and has been installed at Macraes.In addition to the standard basic instrumentation and control, the new system at Macraes consists of a froth image analysis system, a froth velocity control, and a level control system which utilises adaptive feedforward compensation. There are three TankCell«-300 cells in operation at Macraes since November 2007 and the new control system was commissioned in December 2007.The paper will include comparative data from pre- and postsystem installation and discusses benefits including optimised recovery, improved performance, as well as ease of operation.

Jan 1, 2009

The history of potential large scale development at Stawell in northwestern Victoria dates back to 1914, when Great Boulder Mines Limited, of Kalgoorlie, Western Australia, took up options on some of the major mines in the Stawell Goldfield. Despite this and other attempts by various groups over the next thirty years, mining activity on the field gradually dwindled to the retreatment of old mill tailings.A static price for gold and indifferent drilling results prevented a major effort towards reopening the field until the late 1970's. A renewed exploration effort led to the discovery of sufficient reserves to justify installation of a carbon-in-leach gold treatment plant.

Jan 1, 1984

By J Green, R Bartlett, A Goldstone, D Ferguson

Solid Energy New Zealand is developing an extension of its Rotowaro open cast coal mine near Huntly. This large 8 year, 11 million tonne opencast coal mine, referred to as the Awaroa Project, is fundamental to Solid Energy's medium term business strategy and meets its open pit coal resource needs while further resources are developed for the long term. Equally importantly the project is also fundamental to meeting New Zealand's energy requirements in the face of growing demands, a dwindling gas resource, and dry winters creating hydropower shortages. This project with its national significance in the current energy climate, its significance to Solid Energy as a business and its significant size has been consented against a backdrop of criticism of the Resource Management Act and the introduction of the 2003 amendment to the Act. As is common practice for this type of project Solid Energy conducted a significant technical programme in order to complete a comprehensive assessment of environmental effects. Solid Energy also has an active programme of community and interested party consultation and this programme formed the basis for project based consultation with local residents, regulatory bodies and iwi. As a result of the approach taken the environmental effects of the project were shown to be no more than minor and Environment Waikato considered that the project should be processed under the limited notification provisions of the RMA amendment. The project was processed under RMA quickly and efficiently and consents were granted within 6 months of lodgement. The RMA and its 2003 amendment provided a good framework for dealing with this project and did not impede the process of development of this important energy resource.

Jan 1, 2004

By Willis I. L, Stevens B. P J, Stroud W. J

The Early Proterozoic metamorphic rocks of the Broken Hill (BH) Block have been recently subdivided into sixteen formations and four groups (Willis et al., 1983b, Stevens et al., 1983). This stratigraphic subdivision has relied upon recognition of distinctive mapped rock units and "associations" of mapped rock units, which characterize particular lithostratigraphic units. The rock units and rock unit associations define local ordered sequences which can be compared and correlated, thereby establishing the stratigraphic succession. In the Clevedale homestead, Thackaringa, BH City, Bores Mine-Freyers mine, Silver King mine, and Brewery Well areas, coherent stratigraphic successions have been interpreted. These areas illustrate the regional variability of the stratigraphic succession and facies changes within individual stratigraphic units. Stratigraphic type sections are located in the Thackaringa, Bores Mine-Freyers mine, Silver King mine, and Brewery Well areas. The principles of stratigraphic interpretation applied in the BH Block can be used in other areas of Willyama Supergroup outcrop such as the Euriowie, Olary and Mount Painter Blocks. The general technique may also have applicability to other highly deformed and metamorphosed terrains.

Jan 1, 1983

By Wright S

The feed to the Cockle Creek Imperial Smelting Furnace consists of mixed Pb/Zn con- centrates and lead sulphate-containing elec- trolytic zinc plant residues. Roasting was investigated as a means of desulphurizing the feed to less than 1%. Laboratory studies showed that two process streams were required in which concentrates containing 20% Pb were roasted separately from the leach residues. The residues along with fume from the roast- ing and a portion of concentrate were desul- phurized by means of the roast reduction reaction. Conditions were defined to give

Jan 1, 1986

The subject of heat sources in deep hard rock mines, the limitation of forced ventilation to cope with these heat loads and the sizing of refrigeration plants to boost the cooling effect of the ventilation air are discussed. The development of plant selection criteria and operating experience at North Broken Hill Limited is outlined. Future options for North Broken Hill Limited and like deep mines are summarised.

Jan 1, 1982

By J J. Wilkinson, C J. Ha, R J. Herrington

The Pic de Fon iron oxide deposit is a potential major new source of iron ore, located at the southern end of the Simandou range in eastern Guinea on the West African Craton. The deposit is hosted by banded iron formations (BIFs) within a supracrustal sequence, which lies unconformably upon a crystalline basement. The host BIFs and shales have been metamorphosed up to staurolite-grade itabirite and phyllite respectively. Stratigraphic relationships are obscured by polyphase deformation, although the sequence appears to comprise a lower phyllite(-minor quartzite) unit and transitional phyllite-iron formation overlain by three itabirite units. It is the itabirite units, selectively enriched to iron grades in excess of 65 per cent Fe (with low deleterious elements), that constitute the Pic de Fon deposit. Samples acquired from exploration diamond drill holes and outcrop across the deposit have been collected to investigate the Pic de Fon lithologies and iron-rich material types. Initial research techniques have included geological mapping, reflected light microscopy, x-ray diffraction (XRD) studies and ICP-AES geochemistry. The aim is to develop a model for deposit genesis that may assist future exploration and deposit exploitation planning. Results to date have identified a variety of hematite textures, which include recrystallised trellis, interlobate and granoblastic hematite after magnetite. In addition, fine-grained bladed to acicular microplaty hematite appears to both replace itabirite banding and infill porosity. Field relationships indicate a structural control of microplaty hematite development. Geochemistry and XRD results suggest a loss of silica with negligible iron addition during the conversion of itabirite to ore grade mineralisation. The enrichment process(es) is also accompanied by a gradual increase in K, Mg, Na, (Ca and Al).

Jan 1, 2005

By Hayes P. C, Matthew S. P

The product morphologies formed on the reduction of dense wustite crystals are classified into three types, A) porous iron, B) porous wustite covered with dense iron, and C) dense wustite covered with dense iron. The mechanisms of formation of these structures and the effects of impurity elements on the product morphologies are discussed.

Jan 1, 1985

How many of you have felt tired and light-headed after standing or working in the sun or by the oppressive, hot, muggy conditions of an Australian summer? For those of you who have, you've experienced the minor effects of heat stress. Heat

Jan 1, 1994

The changing characteristics of raw materials has highlighted the limitations that conventional vibrating screens have in the handling of fine wet sticky materials. These' limitations have led to the development of a totally new concept of screening, the Rotating Probability Screen. In order to illustrate the practical benefits to be gained by the extraction of fine materials ahead of subse quent processes particularly in the coal industry, the experiences gained in Ro-Pro installations in America, Australia, Europe and Britain are drawn upon.

Jan 1, 1984