Search Documents

Jan 1, 2004

By Milawarma E, Cusack C

The Sapan Dalam coal deposit of Indonesia consists of ten steeply dipping seams with thicknesses varying between 0.1 and 3.5 m and split by shale, clay, silt and sandstone. The area contains four faults dipping about 75¦ with four to 85 m vertical displacements. The complex nature of the deposit coupled with limited 27 exploration drillholes at an average spacing of 200 m made it difficult to create a realistic geological model. A three-dimensional gridded seam model gave a fair representation of the deposit. Attempt to create an optimum pit using the WHITTLE 3D pit optimiser proved unsuccessful since the pit optimiser is restricted to standard regular or fixed blocks. The gridded seam model was converted to a fixed block model prior to the optimum pit design. Smoothing and pit base controlling were also introduced to obtain a smoother pit. A mining scenario produced 3.6 million tonnes of coal, 28.4 million bcm of waste and US$18.1 million revenue.

Jan 1, 1995

By Quast K. B

The effects of metal ion addition rates and contact time on the activation of synthetic sphalerite using copper, cadmium and silver ions were determined in order to investigate the exchange characteristics at the mineral surface. The stoichiometry of the adsorption indicated that the activation of sphalerite involved both a simple ion exchange and redox process in which the activating ion and oxygen were reduced, and the mixed-sulphide surface was oxidised to produce elemental sulphur and a metal-deficient sulphide surface. Unactivated sphalerite was shown to be relatively hydrophilic, with recoveries usually less than 20 per cent for a five-minute float. Activated sphalerite could be readily floated without the use of a conventional collector. This inherent flotability of the activated sphalerite had previously been associated with the formation of a metal-deficient sulphide layer; however, this study emphasizses the significance of the surface oxidation processes occurring.

Jan 1, 1993

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

By Rajan S, Mainwaring P, Gould WD, Beaulne M

Polished discs of a complex sulphide ore were leached with three lixiviants; a mixed culture of Thiobacillus ferrooxidans and Thiobacillus thiooxidans, Thiobacillus ferrooxidanalone, and ferric sulphate. At either one or two week intervals the discs were examined by scanning electron microscopy, and the amount of soluble metals released from the discs were determined. The mixed culture solubilized more Cu, Zn and Pb than did either ferric sulphate or T. ferrooxidans alone. However, no differ-ences were observed between the three treat-ments by scanning electron microscopy during the first 44 weeks. The minerals were attacked in the following order: pyrrhotite, cubanite, sphalerite, pyrite and chalcopyrite.

Jan 1, 1990

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

By Kneisley RO

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north- central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield- pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)- wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By McKew M, OÆRegan

Rapid access longwall mining' or 'longwail punch mining' is a proposed extraction method whereby longwall gate roads are driven into a seam directly from an opencut highwall. The longwall panel thus formed is retreated back to within 40 m of the highwall providing an extremely simple, reliable and therefore highly productive longwall mining system. The concept is of particular benefit for the recovery of isolated pockets of coal (adjacent to a highwall) not easily accessible from a conventional underground mine. As panel gate roads are driven directly from the open strip, minimal delays are incurred between the end of open cut and start of underground production, allowing the method to bridge the gap between open cut mining and a total underground commitment. The study was specific to the Bowen Basin, and given the likely conditions, no significant operational or geotechnical hinderances to the concept could be identified. It was therefore concluded that longwall punch mining would not expose the operator to any additional risks above that normally associated with the introduction of longwall mining. Thus, longwall punch mining is an attractive option, both operationally and financially, for open cut mines reaching their maximum economic Death.

Jan 1, 1988

By Grieveson P, Rajakumar V

The reduction of an ilmenite concentrate with coal at 1000, 1050 and 1100¦C was investigated using thermogravimetry and X-ray diffraction, optical microscopy and electron probe microanalysis of the product. The effects of temperature, coal particle size, addition of ferric chloride and preheating of the concentrate in argon on the reduction kinetics and mechanism were determined. The rate of reduction increased significantly with temperature and was enhanced by the addition of the catalyst. The morphology of the iron was primarily determined by the degree of weathering of the particle. Significant coarsening of iron was obtained in the dense particles by the addition of ferric chloride. The sequence of reduction and the enhancement in the rate of reduction by preheating the concentrate in an inert atmosphere are discussed.

Jan 1, 1991

A Study on Process Mineralogy and Mineral Processing of Complex Carbon-Bearing Cu-Pb-Co-Ni Multi-Metal Sulfide Ore by Bulk Flotation

Sep 13, 2010

By White A. H, Vihena M. T M B

Presently, orebody modelling consists basically of fitting a mathematical model to represent spatially a certain geological variable, generally grade. An orebody model is constructed from a set of sample data obtained from various locations in the orebody, thus it is only one form of representation of the true phenomena. Checking the compatibility of the data with the modelling procedure is the most important factor when assessing confidence in the orebody model. The level of confidence in the model will depend on the adequacy of the data set and the validity of the basic assumption required by the modelling method. Fractal geometry is one way of modelling the spatial distribution of a geological variable in an orebody geometry. Fractals can be used to interpolate the Z(x) geological variable at unsampled sites. The concepts of self similarity and self affinity that form the basic assumption of fractal geometry theory which areinvestigated. The population distribution of the geological variable in question must be examined to determine the appropriateness of both fractal geometry and geostatistical modelling methods. The selection of the most appropriate method depends on the available data. A researcher or a practitioner needs to understand the strengths and limitations of the various modelling methods before choosing the most appropriate method. This study investigates the fractal properties of grade distribution using the variogram and some proposed variations as techniques to measure the fractalness. The aim is to assess applicability of fractal geometry theory to modelling ore grade distribution in a deposit. A comparison of the results demonstrates the methods which better capture the spatial behaviour of the variable under study.

Jan 1, 1995

By Dickson T. J

Slag cleaning is an important part of the pyrometallurgical operations at the Kalgoorlie Nickel Smelter. It is a complex system with many streams of different phases and composition. Some of these streams are very difficult to control and/or monitor. Through the use of a statistical computer package, called Minitab, key relationships affecting the economical operation of the slag cleaning process have been found. Data for the statistical analysis was collected from all possible variables around the appendage.

Jan 1, 1991

The Government Mining Engineer of South Africa has decided to legislate that Self Contained Self Rescuers (S.C.S.R.) become a mandatory piece of equipment for all those persons proceeding underground. It is envisaged that: * employees in underground coal mines will be fully equipped with S.C.S.R.s during 1988; * those persons employed in gold mines during 1988/89; and * personnel in all other mines by the end of 1990. It is the intention of this paper to discuss the introduction of these auxiliary life support systems, and to give an update on current market developments.

Jan 1, 1988

By R. A. Frith, M D. Goodz

Ore-bearing minerals that are located along microfractures are always susceptible to loss during the breakage and sampling of the material. Further losses occur with on-site sample preparation and splitting prior to laboratory analysis. In these cases solid whole rock channel or core samples should be handled with due care to ensure all fines and loose particles are collected and included in the sample for total chemical analysis.Similarly open hole and reverse circulation drill methods are not usable in areas containing old mine workings, heavily fractured ground or highly degraded/oxidised mineral assemblages. Nor are these methods usable to assess a bulk mineable target where the enriched zones were peripheral to or between old mine cavities.

Jan 1, 1993

By Skinner J, Brackenbury K

The AuPlus" Systems have been applied in the gold mining industry to achieve improved gold recoveries, faster leach kinetics and reduced cyanide consumptions. Calcium or hydrogen peroxide, collectively known as peroxygens, can be used. The choice depending on plant design and the nature of the ore. Laboratory test work and plant trials are included in this paper to illustrate the benefits of peroxygen usage in extractive gold metal- lurgy.

Jan 1, 1991

By Jackson D. G

Iron ore mineralisation in the Paraburdoo environs is known to extend almost continuously over a strike length of 55 kilometres. Six formations of the Mount Bruce Supergroup con- tain high grade mineralisation in varying degrees of importance. Ore is currently being mined from the Joffre and Dales Gorge Members of the Brockman Iron Formation, with smaller, less significant amounts, occasionally taken from the lowermost units of the Weeli Wolli Formation and the upper parts of the Mount McRae Shale. Regional mapping has demonstrated the existance locally of a major unconformity at the base of the Wyloo Group sediments out- cropping south of the minesite. The basal con- glomerates at the unconformity are sometimes mineralised at Paraburdoo. A supergene enrich- ment process controlled by structure, strati- graphy and topography is the only one which can satisfactorily explain the disposition and chemistry of the Paraburdoo iron orebodies.

Jan 1, 1979

Over the 20 years to 1990 the Australian mining industry, presently worth some $A60 billion, generated a negative real rate of return (McDonald, 1992); not surprisingly under-performing the returns from bonds and industrial equities. Over this same period more than $A70 billion was invested in expanding the Australian mineral industry.

Jan 1, 1993

The Hunter Fracture Zone can be traced into the Fiji group, and onshore SE Viti Levu in the form of NE-trending morphostructures. NW- trending morphostructures offset the NE elements. Structural mapping of Suva Harbour indicates that the NE elements are grabens bordered by faulted monoclines. Faulting is characterised by block-rotations and dip-slip displacements. The NW morphostructures are faults displaying elements of both dip-slip and strike-slip movement. Structural overprinting suggests that the NW faults represent the youngest phase of deformation, and current seismic activity occurs on this trend. A conceptual, geomechanical model of the deformation invokes toppling and wedge failure at the edge of the Fiji platform, translating material downslope into the Hunter Fracture Zone. The interference pattern produced by the superposition of the NW on the NE structures consists of a series of circular features bearing superficial resemblance to volcanic centres. Known mineral deposits in SE Viti Levu correspond closely to these features. The formation of the circular features postdates mineral genesis, suggesting that the features provide a focus for the enhanced exposure of mineral deposits rather than a source of mineralisation. There is a close association between mineralised exposures and interference patterns in extensional structures in SE Viti Levu, and a correlation between these structures onshore, and the Hunter Fracture Zone cum South New Hebrides Trench offshore. Future mineral exploration in the SW Pacific will benefit by closer consideration of the geologic structure of Pacific islands bordering the extensional regimes of deep oceanic trenches.

Jan 1, 1987

Twelve years ago, Jeffrey Mining Machinery Division of Dresser Industries Inc. developed the 120H HELIMINER. This machine was the world's first fixed-drum continuous miner and soon became the standard among manufacturers of continuous miners throughout the mining machinery industry. This paper will first outline a brief history of continuous miner development, then discuss significant parameters which are essential to a successful continuous miner design, and finally describe a number of specific applications of Jeffrey continuous miners in a variety of materials, such as coal, potash, iron ore, and trona, around the world.

Jan 1, 1978

By Dixon D. R, Sparrow G. J

Pressure leach liquors from the pressure oxidation of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore were treated to remove iron, either by pressure oxidation (the Hematite process) or with particles of magnetite (the Magnetite process), followed by cementation of various metals with zinc dust to obtain a purified solution from which zinc was electrowon. Satisfactory iron removal was achieved by both processes after neutralisation to pH 4.5 or 5.5. Pressure oxidation of the liquor at 200¦C and 690 kPa oxygen overpressure, conditions similar to those of the Hematite process used in the zinc industry, resulted in the precipitation of the iron as hematite. With the Magnetite process, an iron hydroxide was precipitated onto magnetite at atmospheric pressure and ambient temperature and removed by a magnetic separation step. The performances of both these processes for the removal of iron are compared. It is concluded that the Magnetite process offers considerable cost savings. Other impurities, in particular arsenic, were also removed with the iron in both processes. Cementation at pH 5.2 and 85-90 ¦C with 3.5 g/L zinc dust reduced the levels of copper, cadmium, and nickel to a satisfactory level and subsequent electrolysis in a laboratory cell gave an acceptable deposit of zinc.

Jan 1, 1989