Search Documents

By Qixiang Y

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst,and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas.This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By Kallioinen J

This paper discusses different possibilities to enhance coarse particle flotation using forth manipulation and improved flotation cell design. Experiments were carried out in laboratory, pilot and industrial scale ranging from 0.0015 to 100 m3/axle. During the work it could be shown that the conventional idea of one single flotation cell type for both fine, immediate and coarse flotation of coarse and fine particles need different impeller tip speeds and a different froth control objective for effective operation. For optimal operation for coarse feeds the tip speed must be reduced and the froth vertical velocity must be increased to compensate the respective drainage velocity and also the water film thickness must be taken care of. Turbulent eddies below the froth interface should be suppressed. The paper discusses the effects of different froth manipulation variables like froth vertical velocity and froth residence time to the recovery and selectivity. A function has been developed, between the residence time of the froth and the flotation cell's ability to produce an improved concentrate grade as a function of different operating and froth manipulation variables.

Jan 1, 1993

The characteristics and causes of the spoil pile failures at the Goonyella Mine are described, and research results from investigations of spoil pile instability are discussed. Some effects on spoil stability of the development of deep strip mining projects are considered and recommendations are made for relevant research.

Jan 1, 1981

By Warner R. E

Present capacity for molten iron production at Port Kembla is an average of 13 000 t/day from five blast furnaces. The most recently installed blast furnace, No.5, was commissioned in March 1972 with a design capacity of 4 500 t/day. For the first reline currently scheduled for 1977, plans are being finalized.for significant modifications and uprating of capacity. Achievement of the initial design capacity from No.5 blast furnace on a sustained basis was not realised until the third year of operation. Although the furnace is only 42% larger than No.4 blast furnace on an inner volume basis, the more stringent raw materials, operation and maintenance requirements of the larger furnace and more complex equipment have been found to be much more critical than anticipated in the planning stages. These problems have also been experienced by many other companies who have recently installed large new blast furnaces. Some of the principal problem areas are described together with measures taken to over- come the difficulties. The problem areas include the failure of'the shower cooled bosh, failure of the upper shaft brickwork, sludge

Jan 1, 1976

By Corrans I. J, Yan D. S

The CIP process for gold recovery has enjoyed widespread application in most gold-producing countries. The development of a mathematical model of the CIP process has value for use in process design, process optimisation, and process control. Mathematical model development through laboratory experimentation is an important step in the design and optimisation of the CIP process. For this purpose, data has been generated through small scale laboratory leaching and adsorption tests both in batch and continuous mode. This test program has been carried out on specific ores of various types prior to the application of the models to production CIP plants utilising these ores. The applicability of leaching models derived from batch experiments was tested in a continuous five stage CIP pilot plant. The models were then adapted to scale-up the batch to the small scale continuous operation.

Jan 1, 1991

Potential hlghwaJl mining reserves in Australia are large, but geotechnical and operating conditions are quite different from those where highwall mining has evolved in the USA. In order to achieve safe and effective resource recovery, equipment and procedures should be developed to penetrate 250 m in the Australian mining environment. This paper identifies key auributes to be incorporated in such machinery and methodology. These suggestions are intended to promote discussion on innovations to satisfy Australian requirements for highly productive, safe and environmentally acceptable techniques.

Jan 1, 1993

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981

By Umar N

Traditional exploration has been undertaken by both local and overseas experts to discover tin deposits in Indonesia over almost 300 years. Indonesia is part of a tin belt which runs from Myanmar in the north through Malaysia to Singkep, Bangka, and Belitung islands in Indonesia in the south. The discovery of alluvial tin deposits is becoming harder as the more obvious geological targets are exhausted and topographical conditions become more difficult. New approaches are required to sustain successful exploration. There are indications that tin deposits can be found at depth on-shore as well as off-shore. These deposits are found associated with tough clays. On-shore tin exploration is hampered by swampy areas, while the off-shore search is often affected by difficult sea conditions. These factors lead to increases in the cost of exploration as well as the cost of subsequent production. Tin price fluctuations and environmental issues are also of major concern in the planning of the future operation of tin mining in Indonesia.

Jan 1, 1996

By Savidis G

The characteristics of 'Z' (Back-over run) and 'R' (Reverse) ventilation systems are dis- cussed in relation to their suitability for longwall mining. Experience in European mines has been described as a basis for comparison with Australian conditions. In assessing the merits of each ventilat- ion system, such factors as longwall layout (pillar design, number of headings and gateroad stability), the need for gas drainage and bleed- er systems, as well as the influence of seam dip have been considered relevant. The R system is generally applicable for single and two heading development in seams where gas emission is a less serious problem. In contrast, the lower extraction to development ratio of the Z system (which arises from using three or more heading layouts) is considered more favourable where high gas emission occurs. The Z system provides greater flexibility with respect to the provision of refreshing air at the tailgate end, access of men and materials, installation and retrieval of gas drainage systems and the ability to interchange main- gate and tailgate roadways in cases where roof strata loads are difficult to control, or where cpam in hac an influrnra

Jan 1, 1983

By Wasserman A. D

Methodological approaches and in- vestigation results are considered in the paper of heatmass transfer processes when harmful impurities are scattered and remo- ved from chamber-like workings, of the air distribution in complicated ventilation sys- tems and of chemical conversion of exha- ust gases in mine atmosphere when diesel equipment is operating. The results presented in the paper are the base for creation of the automatic design, control and regulation of the venti- lation processes.

Jan 1, 1988

The Lennard Shelf is an Upper Devonian carbonate reef complex striking northwest for 350 km along the northeast margin of the Canning Basin. Numerous small Mississippi Valley type (MVT) Pb-Zn prospects occur within this belt, including the Wagon Pass prospect, located 105 km east of Derby in the Napier Range. At Wagon Pass, the base of the Upper Devonian sequence is a cobbly, dolomitic sandstone, the Van Emmerick Conglomerate. This is conformably overlain by the Frasnian to Famennian Pillara cycle Lower Napier Formation fore-reef deposits. These are characterized by red algal wackestones and terrigenous stylo- bedded packstones, with common dolomitization. The conformably overlying Famennian Nullara cycle contains a classic reefal assemblage, consisting of flat lying Nullara Limestone back-reef, fore-stepping massive Windjana Reef, and steep basinward dipping Upper Napier Formation marginal slope. The Nullara cycle is not dolomitized. The Wagon Pass mineralization is hosted by Lower Napier Formation dolomite. Mineral- ization consists of complex intergrowths and semi-massive assemblages of sphalerite and galena, with subordinate pyrite, marcasite, chalcopyrite, bornite, digenite, covellite and bravoite. Ore textures include granular and colloform. Gangue minerals are dolomite and very fine grained green chloritic clay. Although mineralization commonly occurs as reticulate fracture fillings, its overall distribution is stratabound. Ore paragenesis involved early "diagenetic" dolomitization, followed by breccia formation with chloritic and granular dolomite matrices. Main stage galena-sphalerite mineralization then occurred, accompanied by pervasive chloritization of silty units. Ore genesis was probably related to basin-derived "oil field" brines, with open space textures in the mineralization quite comparable to textures seen in Canning Basin dolomitic hydrocarbon reservoirs. Fluid inclusions in the host dolomite have typical MVT homogenization temperatures of 70-1150 C, and contain minor organic phases. The Van Emmerick Conglomerate, with its high porosity, dolomitization and weak Pb-Zn anomalism, was probably the aquifer for the mineralizing brines. Access of ore solutions to the Wagon

Jan 1, 1986

By Muir D. M

Highly saline process water has a number of implications for the CIP process during the leaching, adsorption and recovery of gold. The reduced oxygen solubility in saline water can seriously reduce the rate of gold leaching, while dissolved oxygen meters do not necessarily reveal actual oxygen concentrations in saline water. High levels of magnesium in the ground water necessitate operation at lower pH (-9), with the potential for greater cyanide loss via HCN stripping. In addition increasing salinity renders viscosity modifiers largely ineffective.The adsorption capacity of aurocyanide onto activated carbon is improved with increasing salinity, but misleading results can be obtained in assessment of gold loading kinetics of plant carbon samples already loaded, or partially loaded, in saline water if subsequently tested in fresh water. Elevated chloride levels in the Zadra elution process can cause severe anode corrosion in the elecuowinning cell. The Anglo elution process is tolerant to only slight increases in water salinity, but elution times can be reduced by ethanol addition. Care is required in carbon regeneration, as salts can catalyse carbon decomposition as well as increase kiln corrosion.

Jan 1, 1994

By R Linares

The efficient operation of any modern metallurgical facility depends on the accurate measurement and estimation of flow rates, inventories, and composition of their intermediate and final products. All of this information is subject to both statistical errors and gross errors, which can lead to poor estimation of efficiency, yields and specific energy consumption. The detection and the elimination of these errors require not only plant data, but also product transactions and the operational events. Once the gross errors have been eliminated, it is possible to estimate validated performance indicators, such as grade recovery or yields. This paper describes the methodology to implement a unification and gross error detection system using the available infrastructure of both information and data reconciliation system. It covers the different infrastructure layers, from the data collection layer to the data validation and reconciliation layer. In addition, the impact of these methodologies on the decision-making process is presented.

Jan 1, 2005

By S Arthur, J Mills, A R. Penney

A key aspect of seismic management for narrow vein stoping of the west zone at the Beaconsfield Gold Mine has been the development of a fully remote extraction method that does not require personnel access to sill drives within the orebody once stoping commences. Initially, sill driving within the reef is undertaken in a conventional fashion under geological control. Sill drives are developed at a vertical backs-to-floor height ranging from 7 - 12 m. This mining stage includes all activities prior to the commencement of stoping, after which no personnel enter the unstoped section of the sill drive at any time for any purpose. The key aspect of the remote mining cycle is the use of footwall drill drives paralleling the ore drive at a minimum separation of 6 m under survey control. These drives provide the platform for fan drilling of the orebody. Up to 20 m strike panels are blasted in a single shot using electronic blasting techniques. Ore is mucked from the extraction level sill drive using tele-remote loaders. Aerials for tele-remote operation are installed through boreholes from the footwall drive, negating the need for personnel access to the sill drive. Once mucking of a stoping panel is complete, a laser scanning survey instrument is used to survey the final void for subsequent design and production reconciliation purposes. The survey instrument is mounted in the bucket of the tele-remote loader, and is also operated remotely. Finally, tele-remote loaders are used to dump waste rock fill from the upper sill drive. A system of flags and cameras installed in boreholes from the footwall drive assists the operator in locating the live stope edge during the filling cycle, again negating the need for personnel access.

Jan 1, 2008

By Terrill JE, Fergusson LJ

In the last decade of precious metal exploration, several important gold discoveries have conclusively demonstrated that epithermal gold deposits formed in what were once active geothermal areas. A significant deposit in this category is the Lihir Island discovery in the Tabar-Ferri volcanic island arc off the coast of New Ireland, Papua New Guinea. Within that arc are the Feni Islands where exploration by Esso PNG Inc. and City Resources Ltd. has been carried out since early 1984. On Ambitle Island in the Feni Group, an epithermal gold prospect located within a young caldera has been tested by diamond drilling. The drillholes intersected a boiling zone at depth beneath acid altered 'cap' rocks. The zone is 30-60 metres thick and comprises hydraulically fractured and mineralised lavas with gold grades of 1-7 g/t. The prospect is still an active geothermal area with current boiling in the zone tested. As on Lihir, the recent epithermal alteration and mineralisation overprints a relict prophyry system. On Ambitle and the adjacent Babase Island several other, cooler exciting gold prospects are currently being tested.

Jan 1, 1987

By Dharmappa HB, Sivakumar M

This paper is concerned with two case histories of wastewater quality management in underground coal mines in the Illawarra region. The first investigation briefly presents an analysis of mine water discharge having an extremely high concentration of suspended solids and consistently high barium concentrations, averaging, 14.4 mg/I Barium, over the sampling period. A laboratory study of chemical precipitation processes has indicated that about 91% of barium could be removed by using ferric sulphate and lime. On the basis of the information obtained from the environmental audit process an alternative water treatment and reuse system incorporating 51% reduction in the water consumption with 32% less off-site discharge has been suggested (Thomas, 1995).The second case history is concerned with the storm water management at a mine situated in the Illawarra escarpment where only 20% of the wastewater generated in the colliery is discharged off-site. Computer modelling of the storm water system showed that 75% of the clean runoff becomes contaminated through poor management practices and causes the process wastewater treatment system to fail in wet weather. Suggested improvements include relatively simple alteration to the coal wash filtration dams which are expected to reduce the periods of inefficient operation of these dams by 95%. The use of storm water diversion channels and detention basins can reduce the overflow volumes by 70 - 100 % for a ten year ARI (Average Recurrence Interval) storm event (Wingrove 1996).

Jan 1, 1998

The New England Fold Belt forms the easternmost and youngest section of the Tasman Fold Belt System of eastern Australia. From middle Palaeozoic to Early Cretaceous time it was the site of extensive episodic calc-alkaline magmatism related to W-dipping subduction. The oldest rocks may have formed at least partly in a volcanic island arc, but from the Late Devonian, the fold belt developed as a convergent Pacific-type continental margin. For Late Devonian-Carboniferous time, parallel belts representing continental margin volcanic arc, forearc basin and subduction complex assemblages can be recognised. Major dextral transform faulting may have offset parts of the fold belt in the Late Carboniferous. In addition, some structural blocks which appear to be out of place in the overall palaeogeographic setting are possible exotic or suspect terranes. A great variety of lode deposits ranging in age from middle Palaeozoic to Early Cretaceous is present in the New England Fold Belt. The vast majority of these are related to emplacement of extensive granite plutons and eruption of continental silicic volcanics in Late Permian-Late Triassic time. However, volcanogenic massive sulphides and volcanic hosted epithermal gold-silver deposits in older rock sequences include one major orebody (Mount Morgan) and several important ones (Mount Chalmers, Cracow, Silver Spur, Cangai and Halls Peak). Some problematical deposits are best classified as metamorphic-hydrothermal. These include gold-bearing quartz reefs and stockworks in sedimentary host rocks, the most important of which are at Gympie, and antimony-gold- tungsten mineralisation in the New England area, mainly at Hillgrove.

Jan 1, 1987

The operators of the iron ore railroads in the Pilbara faced problems of excessive wear between rail and wheels as the tonnage hauled increased in the early 1970's. Joint research projects were begun between Hamersley Iron, Mt Newman Mining and the BHP Melbourne Research Laboratories to study these problems and recommend solutions. The particular problems of wheel rail interaction were solved by asymmetrical profile grinding of the rail and modifications to the machining of the wheels. Rail materials were improved through increasing yield strengths by alloying and by heat treatment. Wheel materials were improved by alloying. The economic benefits of these improvements have been demonstrated by much reduced re-rail requirements and other reduced maintenance costs.

Jan 1, 1986

By Watkins JR

Movements in the mineral trade cycle are almost invariably out of phase with the gradua- tion rate of mining engineers, metallurgists and geologists. This commonly leads to situations where graduates are scarce in "boom" periods and in free supply when the trade cycle is depressed. This problem reflects the difference in elasticity and flexibility between the educational and industrial environments. In the educational system the decision that brings students to graduation is made three to five years prior to the event. This is quite a lengthy period of time in terms of mineral trade cycles. By contrast, the mineral industry has far more elasticity in responding to short term fluctuations in mineral trade. The authors do not believe that the mis- match between the availability of skilled personnel and the manpower requirements of industry in the short term is intractable. Much is to be gained by more realistic and rational manpower forecasting combined with greater flexibility in the educational realm.

Jan 1, 1982

Ore reserve estimates form a basis for strategic mine planning at Argyle Diamonds open pit and alluvial operations. Most ore reserve statements are mainly concerned with resource tonnage and grade. Because diamond deposits are low grade, high value resources, diamond quality ($/carat) is also an important parameter. Relatively large variations in quality and/or grade can occur. These variations must be taken into account before the resource potential can be fully assessed. Computers (HP9000 and PC's) are utilised to compile resource inventories. Resource inventories are then ranked on an economic basis. This paper discusses the methods used to compile resource inventories and explains how these are then used to present ore reserve estimates in terms of resource potential.

Jan 1, 1990