Search Documents

By R Kahnt, S Jahn, D Baacke, M Eckart

Relocation into the Lichtenberg open pit mine of about 110 million m3 of sulfide-bearing and ARD-generating waste rock piled up on the surface is the most important and cost-intensive single surface restoration project conducted by WISMUT GmbH at the former Ronneburg uranium mining site. The waste rock comprises for the most part Palaeozoic shales, limestones and diabases with pyrite contents of up to seven per cent. Waste pile relocation began in 1992 and is scheduled to be completed by 2007. The approach used for relocation has been extensively described elsewhere (Jakubick et al, 1997; Hockley et al, 1997; Chapman et al, 1998; Paul, 2003). Following completion of the backfill that will be up to 60 m above the initial ground level, a dry cover will be placed on top of the backfilled mine wastes. The area to be covered amounts to about 220 ha. Design planning for the final cover placement of which is to begin in 2004 had to be based on a comprehensive cost-benefit analysis over and above compliance with legal requirements. The crucial question to be answered in this respect was to determine û in addition to the expenditure required to ensure reuse, radiation protection and soil protection û the extent to which additional time, effort and money were justified in order to minimise contaminant release from the unsaturated portion of the backfilled pit contributing to total releases into the ground water and possibly achieve savings in long-term operating costs for the on-site water treatment plant. Optimisation was based on contaminant balance modelling for the entire site reproducing dominant physical and geochemical processes. Among the specifics underlying the cover design is that contaminant release from the backfilled open pit must not be considered independently of that from the adjacent flooded underground mine and that a major part of the backfilled open pit will also be submerged. Following weighing of cover-related short- and long-term costs it was found that higher construction costs for the various cover options will not be offset by cost savings in the long-term water treatment. As a consequence of pit flooding, even a costly multiple cover including an impermeable layer will only insignificantly impact on concentrations and loads at ground water spill over points. As a result of comprehensive studies and investigations, a combined cover of cohesive soil material from on-site excavation overlain by a 0.4 m thick storage layer to restore natural soil functions for revegetation was derived and submitted for approval. Together with hydraulic measures, this approach is to meet any requirement in terms of radiology, water protection, stability, erosion protection, and reuse.

Jan 1, 2003

By C Wu, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Halasu porphyry copper belt, located in the East Junggar basin bounded by Chinese Altay to the north and the Tianshan mountains to the south in the Central Asian Orogenic Belt, is one of the major porphyry copper belts in Xinjiang province, north-west China. Combined with previous studies in this area, the magmatism can be divided into three periods: pre-mineralisation activity of 390 Ma syn-mineralisation activity of 380–370 Ma post-mineralisation activity of 360–330 Ma.Through the comparison of zircon chemistry from ore-bearing and barren syn-mineralisation intrusions, negative correlation was identified between Ti-in-zircon temperatures and oxygen fugacity, corresponding to the fact that late-stage syn-mineralisation granitoids contain high water content, high oxygen fugacity and low temperatures with higher mineralisation potential. In addition, the relative low initial 87Sr/86Sr ratios, high eHf(t) and eNd(t) values and mantle Pb isotope characteristics in this study support that the magma forming these intrusions was probably derived from juvenile crust generated during subduction-accretionary processes.CITATION:Wu, C and Chen, H, 2015. Zircon trace elements and Sr-Nd-Pb-Hf isotope systematic of the Halasu porphyry Cu belt, north-east Xinjiang, China, in Proceedings PACRIM 2015 Congress, pp 637–640 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S Ellis, J McMullen, M Habner

A new leaching regime was implemented at Kalgoorlie Consolidated Gold MinesÆ (KCGM) Gidji plant on a cyanide leach of ultra-fine ground sulfide concentrate. High lime concentration and lead nitrate were used to overcome the refractoriness of the fine sulfides (high reactivity of fine sulfides with the presence of gold tellurides). The leach pretreatment stage was shown to be detrimental and was shut down. Lime titration was introduced as part of the process control. It was shown that the leach could be performed at low dissolved oxygen, (ie 3 - 5 ppm) to avoid sulfide oxidation and the associated high cyanide and lime consumption. Plant results showed reduced cyanide consumption (40 per cent) and an accelerated leaching rate, whereby most of the gold was dissolved in 24 hours compared to 72 hours used previously. Similar work was performed at KCGMÆs Fimiston plant, which leached a combined ultra-fine ground sulfide concentrate along with the slimes fraction from hydrocycloning the bulk flotation concentrate. The use of lead nitrate, high lime and carbon-in-leach generated a faster leaching rate and minimised adsorption of gold on fine pyrite particles. The grind, previously controlled with a P80, was replaced by a P98 to give a better operational indication of top size hydrocyclone performance. Before the implementation of the changes, average leach residues for slimes and UFG were respectively 4.0 g/t and 5.5 g/t. With the modifications to the leaching regime, average leach residues were lower by 1.5 - 2.0 g/t. Whilst significant improvements have been demonstrated, further work is progressing at KCGM to further reduce ultra-fine concentrate leach tail grades, and also to improve the understanding of concentrate refractoriness and the factors responsible for differences between laboratory and plant leach results. Estimated profits since the implementation of the new approach are in the range of $A3.5 million per year.

Jan 1, 2005

Within the Ross River Basin, the following types of water were collected and analysed; 19 streams, 24 wells and bores together with 19 samples from the Ross River Dam. The waters were found to contain up to 269 ppm of silica and, although they meet the requirements for industry in all other respects, this extremely high figure means that two basic guidelines should be followed. All steam generation units, except those less than 150 psi should employ hot lime zeolite softening, demineralization or evaporation to remove silica. Cooling systems should only operate on a once through basis.

Jan 1, 1978

By D Trembath

"One of the key risks to the success of a mining operation is the accuracy of the estimates of both the economic mineral and any accompanying contaminants contained within the ore reserve. Misrepresenting the mineralogical characteristics of the ore reserve can result in considerable financial investment in an operation that is in fact uneconomic and/or carries a significant environmental risk. This in turn can result in an unplanned closure of the operation with associated financial, environmental and social legacy. One way to minimise this risk is to undertake high density resource sampling to gain a better understanding of the resource characteristics. However, such an approach is expensive, time-consuming and often impractical. The risk of not having an accurate model is typically assessed during a feasibility study utilising a Monte Carlo simulation method or some form of sensitivity analysis. Importantly, the error margins used in these types of analyses are often based on subjective or very general criteria such as ‘professional judgement’ or an ‘industry standard’. This presentation introduces a conditional simulation method for developing a range of mineralogical distribution models. Based broadly on the method outlined in Journel and Kyriakidis (2004) the proposed approach develops this work further. It combines a geostatistical analysis of the available data with automated mine design software to provide a rigorous method for assessing the confidence in the mineralogical characterisation of the ore reserve. The process is based on simulating possible mine plans based on the statistical characteristics of the available resource sample data. These plans are then assessed against high resolution resource models generated using a Sequential Gaussian Simulation method. The outcome is confidence intervals for important characteristics of the ore reserve estimate relative to the actual resource. These confidence intervals are an objective and transparent measure important for assessing closure risks and represent an improvement over common practice.CITATION:Trembath, D, 2016. A simulation approach for improving the assessment of closure risks, in Proceedings Life-of-Mine 2016 Conference , pp 36–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The current practice of magnetite ore agglomeration involves high temperature oxidation roasting (typically at 1200–1350°C) of magnetite to hematite phase in order to improve the strength and reducibility of pellets. The requirement to pre-oxidise the magnetite before introduction to an ironmaking plant increases the CO2 emissions generated during the ironmaking process. In our previous papers, a novel, alternative agglomeration route for magnetite ores was presented where magnetite was converted to a reducible CaFe3O5 (CWF) phase through the addition of lime to produce a Lime-Magnetite Pellet (LMP) feedstock that can be directly charged to ironmaking units. The LMP process eliminates the magnetite oxidation stage, thereby reducing the CO2 emission during ironmaking. The concept was tested by thermodynamic calculations, high temperature experiments and scaled-down pilot scale test work. In this paper, larger scale synthesis of halfstoichiometric LMPs (1 mole of Fe3O4 and ½ mole of CaCO3) were prepared using a balling drum, followed by overnight drying at 110°C and induration at 1050°C for two hours. The LMPs were analysed using X-Ray Diffraction and Scanning Electron Microscope techniques for phase and microstructure characterisation. The LMPs were found to have 14–15 wt. per cent of CWF phase when indurated under a CO2/CO ratio of 8.5:1. Pilot scale testing of the LMPs was conducted following ISO standard test procedures. The test results indicated the LMP’s had a Reducibility Index (RI) of over 91 per cent, a Tumbler Index (TI) of 87 per cent and a Reduction Degradation Index (RDI) of 4.6 per cent. The results indicate LMPs may be useful as an alternative feedstock to ironmaking processes that would result in lower overall CO2 emissions.

Nov 8, 2021

By K H. Esbensen

The critical role of representative sampling is featured and illustrated by selected examples from the geosciences and beyond. As there already are many demonstrations of the potential (and potentially large) economic consequences of ignoring proper standards with respect to representativity, eg for mining and minerals processing companies, which æstand to lose millions of dollars by failing to optimise exploitation of their mineral resourcesÆ, such need no further iteration here.This keynote lecture, rather, takes a point of departure from the opposite perspective: what is to be gained by a scrupulous stand for representativity? Honesty, reputation, credibility, market advantage - is what!CITATION:Esbensen, K H, 2012. The critical role of representative sampling, in Proceedings Sampling 2012 , pp 9-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

The Australian underground contract mining industry has grown from almost nothing 25 years ago to the point today where half the countryÆs underground mines are using contractors to produce their ore and do their development. This growth was driven by the need to change poor industrial relations and work practices in sectors of the industry, along with the needs of many small gold mine owners to preserve their capital by using contractors to do their mining. The industry is dominated by two major privately owned contractors with a number of other publicly and privately owned contractors making up the balance of the market. This paper discusses the important trends in the contract mining industry and the directions it may take in the next few years.

Jan 1, 2005

By D Cioclea, I Toth

Coal mining can lead to the occurrence of spontaneous combustion events. If these events are not prevented they can give rise to fires that have major adverse effects on the mine plan. After studying the chemical structure of coal, the theories of self-ignition and of the oxidation reaction of the organic compounds, two new technologies have been developed for fire prevention based on the inhibition of coal oxidation. The first technology consists of spraying water drops mixed with inhibiting substances into goaves. The second consists of the infusion of a mixture made of several chemical compounds. Tests performed in situ showed the new inhibition technologies to be highly effective even for longwalls mining coal with a high reactivity from the point of view of self-ignition.

Jan 1, 2005

By R Rimmelin, C Vergara

Heap leach pads are composed of mined ore, usually crushed, disposed on liners to be processed with leach solutions, and the tail of the process is called “spent ore” which are then transported by conveyor belts to be disposed into dumps. It is often to observe stability problems in these dumps, that could affect the equipment working on it and the continuity of the whole mine process. These problems are related to an excess of water content at the spent ore, therefore the operational efforts are focused onto control this geotechnical parameter.This work presents the results of different geotechnical laboratory testing, using samples of spent ore of a mining operation in the north of Chile. In the last 10 years, 3 campaigns have been made to get samples. Valuable information was obtained to identify how specific operational/metallurgical factors could affect the geotechnical behaviour of the spent ore. Special attention is given to the decision to change the metallurgical process adding salt to the heap leach process and its impact to its hydraulic conductivity.Historically, the process has been based on the leaching of oxides and sulphides materials, in separate campaigns, in which it is possible to observe different geotechnical response in the spent ore generated. Recently, it was implemented a new process in which the materials are blended and salt is added, to improve metallurgical performance in terms of recovery. This change generate impacts in the dump, since the geotechnical parameters are affected; decreasing hydraulic conductivity in about one order of magnitude (explained by the salt added).Changes are shown in the geotechnical parameters of the spent ore, considering that the mining source is the same, and how the operational process and dump design are affected.CITATION:Rimmelin, R and Vergara, C, 2018. Geotechnical behaviour of spent ore – impacts of metallurgical factors, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 369–375 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Many of the discrepancies that appear when comparing the results of reducing machinery are due to the nature of the materials reduced and the conditions under which they have been treated. It is therefore necessary that manufacturers should employ standard materials in their tests that sufficiently approximate the substances to be ultimately treated if the information is to be of any value to the purchaser. Another advantage to be gained by employing universal standard materials is that by their means one is enabled to compare the relative values of different types of machines. At present much of the data meted out to the public is insufficient to enable them to judge fairly. Of course the best test would be to send some of the stone tor which the machine is required, to be treated by the various crushers in the market that are likely to be suitable for the purpose, but this is not always possible. It would not take long to become accustomed to judge of the value of a machine for a specific purpose if it was guaranteed to work a certain quantity of some standard rock, even if that standard were not identical with the material to be treated.There are many points to be considered before selecting a machine, such as the size of the rough stone it will take, the size to which it will reduce it the proportions of various grades made when crushing to pass through a given mesh the form of the delivered particles the time taken to treat a+ certain quantity the horse-power required to drive the machine, both when loaded and unloaded whether constructed to crush wet or dry the wear and tear of the machine its total weight and weight of the heaviest part the cost of machine what attention it required whether the wearing parts are readily replaced, and several other points common to all machinery. 'When considering these varying quantities, we can tell at a glance certain machines that are suitable for a particular sort of work, and can then compare those belonging to the same class, thus avoiding errors made purposely or through ignotance by persons interested in different machines, who frequently compare machines originally constructed for.

By Junpeng L, Huiguo Q

Field instrumentation was installed to monitor ground and lining behaviour during and after construction of the Mount Shaughnessy Tunnel (Rogers Pass Short Tunnel) in Canada. The instrumentation was placed in a soft ground section of the tunnel at its crossing with the Trans Canada Highway. The tunnel was excavated through a dense bouldery soil. Presentation of the field data and inter- pretation of the tunnel performance from a geological-geotechnical point of view form the basis of this paper. The loss of ground due to the tunnel excavation was found to be exceptionally small. This has been attributed to the unusually high strength and stiffness of the host soil. Evaluation using the Boundary Element Method, together with a simplified analytical technique, were applied to assess the relevant soil parameters and their influence on the tunnel performance.

Jan 1, 1987

By Smith JW

Studies of 13C/12C ratios of carbon dioxide in seam gases and in secondary calcites show that 1. In mines prone to carbon dioxide outbursting, the source of this gas is external to the coal. 2. Faults draining reservoirs of magmatic or primary carbon dioxide, rather than intrusives, are the most likely points of entry of carbon dioxide into mines. 3. The higher the concentration of carbon dioxide in seam gas and the wetter the mine, the lower the likelihood of secondary calcite occurring as a filling in cleats, fractures etc. 4. A -role played by carbon dioxide in promoting outbursting may be the conversion of calcite to soluble bicarbonate, the removal of this in mine water and the subsequent weakening of the resistance of the bulk coal to stress.

Jan 1, 1980

Based on a principle developed at a South African Mine, the CSIR developed a device with which the alignment of guide rails in mine shafts could be measured. Originally the technique could only be used to obtain guide misalignment values at the bunton sets. At the time this was considered adequate since it was assumed that guide realignment could only be done at the support points anyway. The technology was developed further and now it is possible to obtain æcontinuousÆ guide profiles from the measurements. Software was developed with which a guide realignment schedule can be drafted and the shape of the realigned guides can be predicted. A measuring system based on this technology is being used to conduct guide alignment measurements in shafts. The data is then analysed and a realignment schedule is recommended in consultation with the mine. Such a schedule may be prioritised so that the worst sections in the shaft are dealt with first. The measurement hardware and analysis software are described. Examples are presented that illustrate the principles and highlight measurement errors. A case study illustrates measurements recorded in a newly equipped shaft. A repeat measurement, 18 months later, shows the effect of recommended realignment as well as the change in guide alignment over this period.

Jan 1, 2005

By Wu Y, Qu Q

The Central Coal Mining Research Institute has developed the MAE acoustic emission monitoring system, the BD4-1 portable acoustic emission monitor and the MRB rock burst monitoring system. In the MAE system there is an IBM-PLAT, a receiver and 16 channels and the investigating range is 100 m. The main functions are detecting acoustic events from the working faces, periodically making statistics, prints, displays and storing of the results, and performing the off-line process such as drawing the curves of acoustic activity. The BD4-1 instrument has four channels, it works for more than 24 hours continuously, and keeps the data for more than 30 days after power tum-off. The BD4-1 is suited to the monitoring for a long or a short time as a fixed point where the system is invalid, especially to the monitoring of the acoustic activity promoted by the blasting. There is an IBM-PC/AT, a receiver and 16 channels spread 10 km in the system MRB. The system could on-line collect microseismic events throughout the whole mine, calculate the source location and the energy, and off-line draw the seismic activity draft of time-based or distribution in space. In practice, the forecasting is successful by using the acoustic emission and microseismic monitoring system and the portable instrument.

Jan 1, 1991

Mining, like most other businesses, is based upon capital assets; and the primary cap- ital of any mining company is its ore reserve. A company's survival and growth is, thus, dep- endent upon its ability to replace, increase, redistribute and to diversify its ore reserves. A Kennecott executive addressing a group of geologists in 1957 stated, "Management expects a geologist to find ore! That is the primary objective and the justification of the geologist in the minerals industry. There is no other function that we can rationalize." This is, however, a restricted point of view, and one which I an sure is not fully shared by mining executives or mine operators at the present time. Ore reserves are 'made' as well as 'found' and the geologist contributes to this process. A mining geologist engages in activity in- volving the study of geology in connection with the total mining operation. His major task is the adaption of geological knowledge of ore de- posits and rock behaviour to mining needs, and the application of principles of the science of geology to specific problems of finding, develop- ing and extracting of ore bodies.

Jan 1, 1975

By F Anthes, U Barow

Two tunnels are being bored using a æHydroshieldÆ in section 3.1 of the extension of the Underground railway line 5. At the end of the two tunnels, directly in front of the Hotel Adlon, the shields cannot be retrieved. The steel shell of the shield will be left in place within a sealed concrete block and the reusable components taken out through the completed tunnel. For the first time in Germany, an Underground tunnel is being lined solely by means of UNI rings. BerlinÆs Underground network is 165 km long and has 167 stations. Some 450 million passengers are transported annually. On account of the urban planning modifications that followed reunification, the network has to be adjusted, particularly in the city centre. The most significant project is the extension of the U5 from Alexanderplatz to the Lehrter Bahnhof. After completion, the U5 will be a continuous east-west traffic artery. It will provide a direct link with the new parliamentary and government district, open up new business districts and the cultural centre of the city.

Jan 1, 1999

Lateritic nickel ore occurs as a supergene or residual deposit as a result of the tropical weathering of underlying ultramafic rocks. The mineralisation may be as hydrated Ni-Mg silicates, like garnierite (silicate ore); or as hydrated Ni-Fe oxide (oxide) ore. Non-sulphide ore represents only 30% of the tonnage mined, but represents 85% of the total world's nickel reserves. A typical lateritic profile consists of 4 zones above the unweathered ultramafic parent rock: Zone 1: the "upper laterite" which is dark red-brown, porous and concentrically structured. It contains 0.2 to 0.8% Ni, 48.0 to 72.0% Fe, and 0 to 9.5% MgO. It is often capped by a ferricrete crust. Zone 2: the "middle laterite", which is red-brown to light brown and more porous than the above zone. It contains 0.8 to 1.5% Ni, 42.0 to 48.0% Fe and 0.5 to 6.0% MgO. Zone 3: the "basal laterite" which is yellow-brown to yellow-orange,

Jan 1, 1974

By D J. Fray

In this work, a fused salt electrochemical process was investigated experimentally for production of metals and alloys directly from respective solid oxides by electro-deoxidation. Direct electrochemical reduction of the oxides was carried out in molten CaCl2-based chlorides in an electrolytic cell, incorporating an oxygen-evolving inert anode, over the temperature range of 850 - 950¦C. The technical viability of the process was demonstrated by the electro-deoxidation of pure oxides and oxide mixtures including NiO, Nb2O5, Nb2O5/TiO2 and Nb2O5/SnO2 to produce nickel metal, niobium metal, NbTi alloys and the intermetallic compound, Nb3Sn. Compared to the conventional metallurgical processes for producing these metals and alloys, this new electrochemical process appears to be much less energy intensive, with lower costs and no direct greenhouse gas emissions from the electrolytic reduction process. The present electrolytic reduction process has the potential to be scaled up for the green extraction of a number of non-ferrous base metals and processing of many advanced alloys.

Jan 1, 2006

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994