Search Documents

Looking back 25 years, the role of the drill and blast engineer in an Australian mine seemed relatively simple, with the primary focal points being scheduling of the drill rigs, oversize control, and budget control with respect to consumption of both explosives and drill consumables. The choice of explosive selection was relatively simple, though many mines were becoming involved in trials of slurry explosives, emulsion blends, and low density ANFO blends. Guidelines to assist the engineer towards specific fragmentation targets were scarce, environmental constraints were light, and computers were rarely found on the desks of any mining engineers. Wall control blasting was in its infancy, with the bulk of attention being given to appropriate slope design and little real attention given to factors such as explosive distribution, and optimum delay timing and sequencing. Quantitative measurement of blasting performance was rare. The science of blasting, for fragmentation control, wall control, and environmental impact control was about to be born, and was heralded in those years by intense efforts by the explosive manufacturers and a proliferation of research centres throughout the world. Since the early 1980s, the role of the Australian drill and blast engineer has gone through a major metamorphosis, and currently requires a greater depth of scientific understanding than any other specialisation within mining engineering.

Jan 1, 2004

By Forssberg E

This paper presents the experimental results on the effects of slurry Theology on ultra-fine grinding by a stirred ball mill. The amount of dispersant, slurry density and the particle size were selected as the parameters. The viscosity of dolomite-water slurry was measured by rotational viscometers. It was found that by adding enough dispersant, the effect of particle size from 1 to 10 pm on the slurry theology could be eliminated, but a strong effect of slurry density (tested for a range of 65 to 75 wt per cent) remained. The use of dispersant transformed the slurry from Bingham plastic flow to dilatant flow, which reduced the yield stress to zero, but increased the viscosity at higher shear rates. During the milling process, the viscosity was stable. The yield stress, however, increased suddenly from zero after a certain milling time. The mill operation stopped at the point where the yield stress increased due to poor slurry fluidity. The milling efficiency was found to be higher at a lower amount of dispersant addition or a lower slurry density within the experimental limits.

Jan 1, 1993

By Fallins J

THE John Darling Colliery, owned by The Broken Hill Proprietary Company Limited, is situated 12 miles south of Neweastle, NSW and about 1 mile from the ocean. The area of the holding is approximately 10,000 acres, about half of which underlies the Pacific Ocean. The area was proved to be coal bearing by diamond drill boring: this method not only proved the coal to exist, but gave the depths from which could be calculated. It also proved the existence or otherwise of heavy faulting, which is a very important factor in the design of the underground lay-out of a mine. The location of shafts had to be carefuIly studied, and, before final selection, the following salient points had to be considered:Railway communications.Flood waters.Boiler feed water.Surface buildings.Probability of coal washing.Underground haulage arrangements.Lengths of roadways from a ventilating viewpoint.Before the shaft sites were finally selected, an underground design was prepared to determine the direction of the main drives in relation to the boundaries of the holding, and the of the coal seam: the latter, being an important factor in this particular locality, was ascertained by a geological survey of rock outcrops in the neighbourhood. Size of shafts was the next subject for consideration. This was determined by output, number of seams to be worked, amount of ventilation required, and, on...

Jan 1, 1930

Current problems in predicting sub-surface strata movement and fracture development due to longwall mining have highlighted the need for more accurate, dependable methods of physical modelling of rock mechanics problems which are beyond the capabilities of current mathematical techniques. Physical model studies of the caved zone above the working faces up to the base of a water source are of importance in attempting to understand changes in mass permeability due to induced fracture zones and the resulting ground water conditions. Turkey's most important supplies of coking coals are to be found within the hard coal resources of the Black Sea coast. Coal seams up to 9 metres thick, dipping at angles as steep as 90 degrees are being successfully mined at the Kozlu Mine. Since 1956, mining operations have been carried out under the sea in dry conditions. The undersea mining conditions of the Kozlu Mine have been investigated using scaled physical models constructed from artificial materials which satisfied necessary scaling requirements. Models representing the in-situ conditions were tested and the following extraction sequence was employed: 1. The Sulu Seam extraction 2. The Acilik Seam extraction (as two slices) 3. The Piric Seam extraction. The displacement of the fixed reference points were subsequently measured using a high precision photogrammetric technique and induced horizontal and vertical strains were calculated.

Jan 1, 1988

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

Samples weighing O·25 g are fused with 1 g potassium hydrogen sulphate, leached with 5 ml. of hydrochloric acid, and then diluted with another 5 ml. of acid. After settling, an aliquot of the clear solution is reduced with stannous chloride, and then a zinc dithiol solution is added to form a coloured tungsten complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 4 p.p.m. may be analysed at a rate of 100 determinations per man-day of 8 hr.

Jan 1, 1970

Samples weighing 0·5 g are fused with potassium hydrogen sulphate, leached with 4 ml. of 4 M nitric acid and diluted to 10 ml. with water. An aliquot of the clear solution is treated with EDTA, adjusted with ammonia to give a pH value between 5 and 6 treated with cyanide, ammonia, and sodium diethyldithiocarbamate then bismuth diethyldithiocarbamate is extracted with chloroform and the yellow colour is compared visually with a standard series. Alternatively, the bismuth complex may be filtered on a "Millipore" filter and subjected to x-ray fluorescence spectrometry.

Jan 1, 1971

By Vanderberg B

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras. Todays common approach of utilizing only a single camera system can, in some cases, lead to great errors and erroneous conclusions when motion is assumed to be in a predefined plane of motion. CMe phrase, "What you see is what you get, it no longer true in 3D."). This is especially true in blasting environments which exhibit complex and/or predominant structural geology. The 3D system eliminates this problem, and includes automatic corrections for vertical and horizontal camera optic axis orientation, dimensional controls, lens distortion, field set-ups, projection imaging and digitized inputs. The only information required is the surveyed or known coordinates of at least six non coplanar points in the field of view. Motitn from each camera view is then digitized, transformed through a direct linear transformation, and processed with the 3D software, which also automatically time matches the data, even when the high-speed cameras are operated at different speeds. Eleven calibration constants are generated using an overdetermined system of linear equations to output the true 3D coordinates of motion in the time domain. Applications for this 3D approach are not restricted to just analyzing the kinetics of a blast. The system is sufficiently flexible to allow an accurate, quick and economical method of bench face profile analysis, generate muck pile profiles and estimate volumetric calculations. The recording systems for these applications can be common 35mm still photography and/or video equipment. It is envisioned that this system will soon replace expensive laser surveying systems at a fraction of the cost in the near future. It is also an excellent system to accurately quantify drill pattern layouts and the spatial locations of each blasthole. This information is required for generating single hole based synthetic seismograms to accurately predict the vibrational outputs of full scale blasts. In terms of litigation concerning claims resulting from blast induced ground vibrations to structures, the system is proving to be an excellent and economical method of performing pre-blast surveys where differential settlement is suspect.

Jan 1, 1990

The role played by lawyers in business has, in the course of the last 15 to 20 years, changed perceptively. This development has coincided with, and indeed has been a reflection of, the changing nature of Australian business, especially as the mining industry established its predominance in the Australian economy. The nature and extent of governmental regulation of business, too, has changed markedly. As a consequence, there has been a qualitative'change in the nature of commercial law practice. For the needs of business to be met, lawyers have had to develop specialist skills in new areas. Furthermore, there has been the emergence of the "in-house" lawyer, who increasingly plays a primary rather than a subordinate role in corporate law practice. There is no evidence to suggest that this trend, which is by now so well established, will prove to be ephemeral. Instead, with all indications pointing towards even greater governmental regulation of business activities, the intimate role of the lawyer in business seems entrenched.

Jan 1, 1980

By A J LYNCH

It was Harold McMillan, Prime Minister of England 30 years ago, who used the phrase "The Wind of Change" to describe political events in Africa in his day. So well did this phrase capture the spirit of the time that it echoed around the world, and the echo has never stopped. Change is the constant factor in the society in which we live and everyone of us has had experience of the effect which it has had on our professional and personal lives. Change will not stop, it will continue at an increasing rate and the questions we must answer are how do we prepare ourselves to meet the challenge of future change and how do we take advantage of the opportunities which it will bring? It is these questions which I wish to discuss in this address.

Jan 1, 1989

By V Kainulainen

Sandvik Tamrock Corp has developed an underground rock flow simulation tool OPTIMINEÖ which is a direct simulation tool for matching suitable technology in rock material flow for underground mine layouts and production requirements. The tool gives the possibility of determining intersections, limitations and critical points in the layout and working procedures at an early stage of a new mine/mining area planning process. The tool combines the supplier machine knowledge with operational know-how and mine environment. It can be used for identifying the effect of an individual incident such as the effect of one additional turn in a continuous loading cycle to the daily capacity. This paper discusses the way the OPTIMINEÖ simulation tool operates, the benefits and restrictions, and reviews how it simulates some example cases and how the mines benefit from the tool in maximising the performance and optimising the mobile fleet, scheduling work and fine-tuning the layout.

Jan 1, 2000

By P J. A Lever

This paper presents details of CRC MiningÆs work with waterjet assisted blasthole drilling. The objective of this work was to investigate techniques that reduce the cost and increase the productivity of blasthole drilling. The focus is on a technology that uses a high pressure waterjet to assist the conventional rotary rock cutting action of a tricone drill bit. The potential benefits of this technique are increased productivity, reduced drill bit wear and reduced hole deviation and hence improved quality of drilling. This paper describes the results of a laboratory based experimental program comparing conventional tri-cone drilling performance to the proposed waterjet assisted approach. Additionally, work has been completed looking at the more practical issues around the collection and sampling of drill cuttings and water recovery (recycling) when drilling with a waterjet. These studies have demonstrated that waterjet assisted drilling can significantly increase the rate of penetration over conventional rotary drilling. For the best-case experimental result, the relative improvement was over 40 per cent. More importantly, it is a starting point for examining alternative uses of the additional drill productivity obtained from waterjet assisted drilling. For example, increased drill productivity could be used to improve rock fragmentation by drilling a tighter blasthole pattern in the same time period. an existing drill fleet, then the drill fleet size could be reduced, or improved rock fragmentation could be achieved by drilling a tighter blasthole pattern within the same time period.

Jan 1, 2004

A system of decline mine entries and ore haulages has been designed for the Mt. Windarra mine. This choice was controlled by the nature of the ore- bodies, the mining method chosen and the capital cost of development re- quired for production. Mine entries are being driven 4 metres high and 5.5 metres wide and decline at 11%, to accommodate diesel haulage vehicles of 35 tonnes capacity. The.Mount Windarra haulage system and the design parameters used in its selection and design are discussed, and general design and selection parameters are proposed.

Jan 1, 1973

The intent of this address is to look forward into the 21st Century and present certain thoughts as to how underground coal mining might be conducted. The views in this talk are based principally on the author's experience with mining practices in the United States. It may be difficult to accept, but the 21st Century is a mere 12 years away. What new techniques will be available? To develop an understanding of the way in which technology has been and could be changing, a two- stage analysis is made of mining technology for U.S. Coal. The first phase covers the period 1975 to the present, while the second includes 1960 to 1975. This historical perspective includes a view of underground production by mining methods, considerations of labour productivity, and a review of accident and fatality rates. Several topics are important features of this historical analysis. Among the most significant are: (1) the introduction of Ion-wall mining technology into U.S. underground coal mines, (2) the use of computers to assist in mine planning and design activities, (3) major efforts to improve health and safety performance, with emphasis on underground dust control, and (4) improvements in mining equipment with an eye towards increased reliability and up-time performance. Based on that historical perspective, projections are made in three increments. The first being immediately at the turn of the century, the second being a dozen or so years beyond that, and the third being at the quarter point of the 21st Century.

Jan 1, 1988

By E Yurakov, D J. Ashelford, M I. Slate

The push for increasing coal production rates continues to place increasing demands on mine management to safely and effectively control seam gas. Gas drainage strategies applied vary in both effectiveness and form. Methods employed are a function of assessed risk, gas reservoir characteristics, surface and underground access, budgetary constraints and gas utilisation potential. With the aim of establishing and optimising the effectiveness and efficiency of gas drainage systems, Australian coal miners in cooperation with gas management specialists are embracing the use of gas reservoir simulators and gas emission models. This paper discusses the evolution of gas drainage practices in Australian underground coal mines and the role of gas reservoir assessment methods in optimising gas drainage systems and gas production forecasts.

Jan 1, 2005

The following is a brief summary of the Bulli Colliery and its method of operation when Australian Iron and Steel Ltd. took control.Bulli Colliery is situated about a mile west of the village of Bulli and is some 10 mUes north of the Australian Iron and Steel Company's Steelworks at Port Kembla.The mine is owned by Australian Iron and Steel Limited, who purchased it in 1936 from the liquidators of Bulli Colliery and Coke Works.It is one of the oldest working coal mines in Australia, having been opened about 1858 and has worked more or less continuously since that date.The seam worked is the No. 1, or Bulli, Seam, which outcrops along the escarpment of the Illawarra Range and is generally operated by tunnels, the portal at Bulli being some 440ft. above sea level.The colliery holding is fairly extensive, but the coal seam over a large portion of the area within two miles of the outcrop has been more or less destroyed by an intrusion of basalt.At present there is no coal being worked within a distance of about 21 miles from the surface, the farthest workings being about four miles from the tunnel mouth.The existing main haulage road, for the first two miles from the portal, is not straight; it is very narrow over fairly long stretches and has many changes of grade varying from 3% in favour of the load to 13% against the load.The dumping station and screens are situated close to the portal of the haulage tunnel, and at this point the coal is loaded into railway hopper waggons, which are then hauled by rope to the top of a self-acting incline. The waggons are lowered down the incline, a distance of approximately! mile, the ruling grade being about 18 %.From the bottom of the incline, waggons are hauled by Company's steam locomotive to exchange sidings from whence they are taken by New South Wales Government Railway engine to the Company's Steelworks at Port Kembla.

Jan 1, 1947

Mining companies around the world devote considerable effort to production reconciliation and metallurgical accounting. However, although sampling, weighing and analysis methods used to obtain the raw data for metal balancing continue to improve, they are still areas that are sadly neglected. Using the latest metallurgical accounting package to improve metal balancing is fundamentally flawed if the data used are unreliable in the first place. The basic rule for correct sampling is that all parts of the material being sampled must have an equal probability of being collected and becoming part of the final sample for analysis. If this rule is not respected, sampling bias can easily be introduced. Unlike precision, which can be improved by replication, bias cannot be reduced once it is present. Sampling and sample processing procedures must therefore be carefully designed both to minimise bias and to obtain acceptable precision. The most suitable sampling location is the discharge point of a process stream, where increments can be obtained by taking a complete cross-section of the stream with a sample cutter. Sampling devices that take only part of the stream may introduce serious bias and must be avoided. The moisture content and wet mass of the material being sampled are of similar importance to chemical analyses for determining metal content. The accurate determination of moisture content is particularly difficult, because the moisture content of samples can change after the sample is taken, eg due to moisture evaporation. Hence, moisture samples need to be taken quickly and placed in sealed bags or containers that are impervious to moisture. The moisture content should then be determined without delay. To determine wet mass, a range of weighing methods are used in industry, including weighbins, weighbridges, conveyor weightometers and platform scales. The precision and accuracy of these methods vary considerably, so it is important to select a method with the appropriate precision and ensure that the weighscale is well maintained and regularly calibrated.

Jan 1, 2002

By M Suzuki

Although several models for the surface tension of molten oxide slag have been proposed, suitably accurate predictions of this property are not yet possible. The surface tension, or surface excess free energy, of molten oxides is largely determined by the ionic coordination induced by surface relaxation. However, the associated mechanism of surface structural relaxation for molten oxide mixtures such as slag is complex and not yet fully understood. To allow a better evaluation of surface relaxation characteristics, the present work analysed the ionic coordination associated with the surface-relaxed states of several oxide mixtures. This work especially focused on calcium aluminate slags because these materials exhibit complex relationships between composition and surface tension. The effects of incorporating low concentrations of SiO2 as a surface active component on the surface ionic coordination were also examined. X-ray absorption techniques were used to assess oxygen and cationic elements in glassy samples after surface relaxation treatments, and molecular dynamics simulations based on a polarisable ion model of molten slag with vacuum/melt interfaces were also performed. The X-ray absorption techniques provided data related to electron yields (which are primarily associated with surface features) and fluorescence yields (which evaluate the bulk material). Thus, the ionic coordination characteristics of both regions were investigated. The results of molecular dynamics calculations allowed statistical analysis of the distributions of Al- or Sicentred polymorphs as well as the bond angles between cations and oxygen anions in the vacuumexposed and bulk regions in the equilibrated melt. The results indicated that bridging oxygen ions were preferentially distributed in the relaxed surface region rather than non-bridging oxygens. These bridging oxygen ions represented vertex connections between AlO4 or SiO4 tetrahedra. In the case of the calcium aluminate slags, the addition of one Ca2+ ion as charge compensation for two Al3+ ions was found to be necessary to form two AlO4 tetrahedra. This specific feature of surface ionic coordination could be responsible for the complex trends observed in surface tension data. The incorporation of low concentrations of SiO2 reduced the proportion of tetrahedrally-coordinated Al ions such that higher coordination states become dominant in the bulk of the material, whereas AlO4 tetrahedra were preferentially distributed in the surface region. SiO4 tetrahedra were the preferred Si-centred polymorph and were likely connected to one another to form bridging oxygen ions at the surface. On the basis of these results, a model to predict slag surface tension was proposed, and the energy of the formation of the ionic clusters resulting from surface relaxation was taken into account.

Aug 21, 2024

By Hll J. K, Zhang Y. G

The wear mechanisms of impregnated diamond drill bit matrices are complex and believed to be the key point in solving drill bit self-sharpening problems. A method has been developed to find the change in c,, the wear rate of matrices having different fracture toughness K_ at the increment of drill pressure P. The worn surfaces of specimens were placed under a scanning electron microscope to examine the wear patterns and wear mechanisms at different pressures, and were compared with the worn surface of a practical drill bit. A model is proposed that within a wide range of pressures there exist two different wear mechanisms and three wear regions for cemented car- bide matrix materials. In region one (linear region), at low pressure, the major wear mechanism is plastic deformation in which the preferential wear of the binder phase of the matrix results in the loss of WC, tung- sten carbide particles. Wear rate is controlled by hardness, H as Archard's formula predicts. Wear enters region two and three (non-linear region) simultaneously as pressure is being increased. Consequently, wear transfers to fracture mechanism in which micro-fracture occurs at the root of wear grooves and the material is removed mainly in piece and mass. It has been shown fracture toughness K,, plays a more important role than hard- ness H. It is concluded that for a specific drilling condition, the pressure on the matrix should be carefully controlled and a balance between hard- ness and toughness of the material is essential for a steady drilling Condition.

Jan 1, 1989

Self Advancing or "Poweredtt supports are a successful means of supporting roof and designs have reached the stage where adequate support capa- bility is available for all conditions. Some designs have resulted in equipment being too difficult to transport underground and too complex to maintain. Current trends are reducing those problems and simplicity in hydraulic systems is now the keynote of both supplier and user. There is a good possibility that the "Shield-Chock" support will be the universal design of the future. So-called t'shortwall supports" have been developed to the point where they can be applied with a high degree of confidence to conditions of great variety. Develop- ments by manufacturers and practices of users related to maintenance should result in consistent achievement of designed performance.

Jan 1, 1974