Search Documents

By Wall J, Platell R, Knight P

The Argyle diamond mine is located in the East Kimberley area of Western Australia, some 100 km south of the town of Kununurra. The diamondiferous Argyle olivine-lamproite diatreme was discovered in August 1979. Production began in December 1985 at a planned throughput of 3 Mtpa to recover 25 million carats of diamonds. Presently, Argyle is the world's largest producer of natural diamonds and produced over 40 million carats in 1993 from seven million tonnes of lamproite ore treated. Two phases of evaluation have been carried out. The first in 1981-82 was designed to prove around 60 million tonnes of ore to justify the establishment of a mine with a minimum life of 20 years. The second phase, in 1989-90 involved drilling the orebody to greater depths to provide data on which to plan the final pit design. The final pit contained 120 million tonnes of ore at 5.3 carats per tonne (ct/t) grade. Mining of the planned pit will extend the mine life to around the year 2004, following which it is possible that a further cut-back could be mined. There is also the potential for future underground mining. A substantial amount of geotechnical work has been undertaken due to the fact that the pit will be nearly 500 m deep and is located in a mobile zone causing abnormally high residual stresses to occur in the pit walls. The occurrence of low strength rocks at depth in the pit walls further complicated the situation. Hydrogeological investigations were done to determine pit dewatering requirements and to assess the effect of dewatering on pit wall stability.

Jan 1, 1994

By E Werner, B R. Leavitt

The chemistry of acidic mine drainage discharging from flooded coal mines is commonly reported to improve with time after flooding. This investigation describes a 18-year dataset of post-flooding water chemistry for a below-drainage underground coal mine within the northern Pittsburgh coal basin (Pennsylvania, USA). The Montour mine is a 5650-hectare below-drainage coal mine of maximum 260 metres depth. Montour was closed in 1980 and flooded to within 38 metres of land surface within 4.8 years. Pumping averaging 210 L/s was then employed to maintain water levels at this elevation. The flooded proportion of the mine (by volume) at full flooding was 56 per cent. The shaft where water was pumped from Montour for water control is located about 70 per cent of the distance between the mine water table and the back of the mine ù that is, it is close to the back of the mine. The residence time (total water volume at flooding divided by pumping rate for control) is estimated at 5.6 years. Time series of chemical analyses show three phases of chemical behavior in post-flooding discharge. In Phase I (zero to two years after flooding), iron concentrations were high and reached their maximum (1100 mg/L). In Phase II (two to four years after flooding), a transition was begun to alkaline conditions, with decline in iron and other solutes. In Phase III (>4 years), net alkaline conditions began, with iron concentrations declining exponentially to 50 per cent of mined volume. This attainment of net alkalinity in this case may have also depended on abundant calcite in overburden extended up to 30 m above the mine floor.

Jan 1, 2003

At the Nikkel og Olivin nickel mine near Narvik, Norway, Outokumpu has been the operator since 1993. The mine was opened in 1989 and in 1992 Outokumpu commenced operations to secure concentrate deliveries to Harjavalta's nickel smelter in Finland. Annual production is about 740 000 tonnes of nickel ore grading 0.5 per cent Ni, about 25 000 tonnes of nickel concentrate and about 2800 tonnes of nickel metal. All production comes from underground operations which makes Nikkel og Olivin AS perhaps the lowest grade underground nickel mine in the world today. Production is currently from one of two orebodies, which is known as the Western orebody. The Eastern orebody was worked out by 1995. During Outokumpu's operational period the Western orebody has been delineated and taken to production. The underground exploration and definition drilling involved about 15 000 in of diamond drilling, which was carried out during a nine-month period. Following this a feasibility study was undertaken and production commenced. Improvements were made to the mining methods. Previously the mine utilised open pit equipment underground and this resulted in an enormous amount of additional tunnelling. Grade control and ore delineation were previously based on sparse diamond drilling and all geological information was processed manually. The improvements included the use of underground sludge drilling to increase the amount of geological information, the of a new computer system for grade control and mine planning, new automated underground longhole drilling equipment and the of underground mining equipment which reduced the size of the drives. These changes produced a marked increase in the efficiency of the underground Mine.

Jan 1, 1996

By Binns MJ

Gold/silver orebodies of the Golden Plateau deposit, Cracow, Central Queensland, are currently being exploited by the Cracow Mining Venture. A geostatistical block model has been prepared to assist with long term mine planning. The Golden Plateau orebody, of inferred epithermal origin, is a multiply brecciated, silicified fault complex containing irregular, tabular and pipe- like oreshoots. Historically the lode has been stoped and open cut over a strike length of 750 metres at widths of up to 15 metres and to a depth of 250 metres. The Golden Plateau mine produced 1.55 million tonnes of ore at an average grade of 12 g/t Au and 13.5 g/t Ag over a 42 year period. In the preparation of the reserve model much reliance has been placed on recent diamond and reverse circulation drilling (71 holes in total). However a significant volume of data has been derived from historical level assays and underground diamond drilling. Over 3,000 level assays and 50 underground drill holes contributed to the database. Similar lognormal populations were observed for 1 metre composite grades from each major drilling campaign once corrections were made for core loss. Cumulative frequency plots revealed only one outlier which was cut to the population line. The population statistics from the historical level assays showed a significant difference from those derived from the drill hole composites. Level assay populations were cut to local drill hole populations before incorporation into the ore reserve model. The resulting data has yielded interpretable variograms, the parameters of which have been applied to the preparation of a kriged block model of the deposit.

Jan 1, 1987

By M A. Gontalves, A F. D C Varajpo

The Rio Capim kaolin district, located in the north-east of Parß State, Brazil, constitutes one of the worldÆs largest high-whiteness kaolin reserves for the paper coating industry. It contains, at the base of the main ore, a soft kaolin that gradually changes at the top into a ferruginous duricrust followed by a flint kaolin. The flint kaolin is completely discarded during the exploitation of the soft kaolin. With the view of a more complete beneficiation, aiming at a sustainable development of the minerals industry, the use of this residual flint kaolin has been considered for the manufacturing of zeolites. Zeolites were synthesised from the flint kaolin through a reaction between metakaolinite with soda at 80¦C, for durations of 24 to 144 hours. The transformation into metakaolinite was carried out at 800¦C and was not affected by the titanium oxides. For a synthesis time of only 24 hours, a zeolite 4A very close to its theoretical definition was obtained, whereas for synthesis times longer than 96 hours, a slight formation of hydro-sodalite was also observed. The synthesised zeolites were tested as cationic adsorbents on 0.5 molar solutions of Cu, Pb, Cd and Zn. The adsorption was measured for contact durations of one and three days. It was noted that the exchange kinetics were slow and that the retention was significantly greater after three days than after one day. The retention was greater than 50 per cent of the theoretical exchange capacity for Pb, Cd and Zn, which was different to Cu, where the retention exceeded its theoretical exchange capacity.

Jan 1, 2008

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

By Kim M

Mukuk gold mine in South Korea produces a pyrite concentrate containing gold associated with arsenopyrite as a gangue mineral. The effects of Portland cement as a depressant on the flotability of arsenopyrite were studied to improve the separation of arsenopyrite from pyrite concentrate containing gold. A series of the fundamental flotation tests were performed using Portland cement as a function of pH and concentration of the collector. Flotation recovery of pyrite and arsenopyrite in the fundamental tests with amyl xanthate showed that arsenopyrite was depressed by the addition of a moderate amount of Portland cement, but pyrite was not depressed by it. In the flotation tests of the artificial mixture samples with arsenopyrite and pyrite, following pH were adjusted to be 10.5 by Portland cement, different amount of amyl xanthate was added. The results from these studies showed that flotation recovery of pyrite was 100 per cent under the condition of some addition of amyl xanthate, but arsenopyrite was not floating at all. Portland cement shows remarkable depression of galena, but its effect on the flotability of chalcopyrite is not as clear. In the pulp under Portland cement addition, chalcopyrite can be easily activated by the addition of sodium bisulphite, whereas galena is depressed more effectively. From the batch flotation tests with the pyrite concentrate, the galena concentrate and the Cu-Pb bulk concentrate from the mines, it was confirmed that the results of the batch flotation tests agree with the results of the fundamental flotation tests. The effects of depression by Portland cement on pyrrhotite, marmatite and stibnite are also discussed briefly.

Jan 1, 1993

By S Grano, M Fordham, H Manouchehri, J Curral

This paper focuses on the impact of high pulp temperature on sphalerite flotation after the zinc regrind circuit in the Zinc Plant of Somincor, owned and operated by Lundin Mining Corporation. In the zinc circuit, the zinc rougher concentrate is reground with forged steel media before flotation with one stage of roughing and scavenging, and three stages of cleaning to obtain a zinc final concentrate (zinc grade >50 per cent). After regrinding, sphalerite flotation has been found to be seriously affected by high pulp temperature which may occur during the summer months. Mineral recoveries were found to be seriously reduced at pulp temperatures above 60¦C. At this high pulp temperature, neither elevated copper sulfate concentration nor a decreased pH alone appreciably increased Zn recovery. However, a combination of these two (eg a decrease in pH from 11.5 to 10.8, and an increase in copper sulfate dosage from 400 g/t to 800 g/t) was found to reduce Zn depression at high pulp temperature. At pulp temperatures below 45¦C, the negative influence of pulp temperature on mineral recoveries was minimal. A systematic series of flotation tests and solution/surface analyses were performed to reveal causes for poor sphalerite flotation at high pulp temperature after regrinding. The decrease in mineral recovery was shown to be associated with variations in the surface species on mineral particles in response to the increased pulp temperature. These variations in the surface species include collector desorption and superficial oxidation to form lead/zinc oxide/hydroxides on mineral particles. The influence of the type of regrinding media on sphalerite flotation at high pulp temperature was also addressed in this work.

Jan 1, 2008

Comminution of solids is surely one of the oldest technologies which even in this day and age of DNAs, chips and space exploration continues to challenge our scientific acumen and engineering ingenuity. In essence, this challenge is two-fold. One, as much as three to four per cent of all electric power generated world-wide is consumed in crushing and grinding primarily because the utilisation of energy is woefully poor. Studies have shown that the efficiency of mechanical size reduction processes is of the order of 1.5 to 12 per cent only (Schoenert 1986). Two, with the grinding technologies available to us, we have, at best, inadequate and, at worst, almost negligible control over the shape of the comminuted particles, size dispersion of the ground mass, and the sharpness of mineral liberation. Low energy efficiency and lack of control in the sense mentioned above have far-reaching implications for resource conservation, performance of down stream unit operations, and damage to the environment. Our problem is in fact central to the mineral-energy resources triangle shown in Figure 1 which depicts the close interrelationships among mineral resources which are becoming poorer in content and more complex in mineralogy each day, energy resources which are depleting rapidly without any viable alternate on the horizon, and environmental concerns which can no longer be ignored. It is evident that any improvement in the efficiency of the comminution process impacts directly on the control of environmental damage, conservation of energy and the economics of the operation. These concerns have special relevance for the processing of non-ferrous ores.

Jan 1, 1992

By Finlayson J. F

The advantages of rapid and accurate analyses are becoming appreciated in many industries today and have resulted in a great increase in the number of samples received by their laboratories. This has caused some firms to consider the installation of one or more of the instruments available for analytical chemistry. In this country there are relatively few people with experience of instrumental methods and it is difficult for a firm considering the installation of such equipment to assess the advantages which instruments may give them, and to decide which instruments, if any, will be of most use to them. The object of this paper is to give a brief survey of instrumental methods in the field of inorganic analysis. Instrumental methods of analysis have numerous advantages when used correctly. They enable extremely rapid analyses to be made in many cases, e.g., analysis of refined lead by purely chemical means takes about two days whereas spectographically the analysis can be completed in approximately one and a half hours. The accuracy ofinstrumental methods, generally between 1 and 5%, is higher than most chemical methods for small percentages of impurities. Furthermore, if the instrument can be calibrated against absolute standards the errors are usually random and not biased to one side of the correct result. The sensitivity is high, enabling in many cases the detection and determination of smaller percentages than can be detected chemically. This high sensitivity enables and, in some cases, requires the use of very small samples, and results in considerable savings in reagents, allowing the analysis of considerably more samples without undue loss...

Jan 1, 1951

The epithermal silver-gold Red Rock Deposit is hosted in the Late Permian inter- mediate to silicic composition Drake Volcanics of New England, N.S.W. This deposit represents one of the few low sulfur epithermal precious metal systems in eastern Australia, and differ! from epithermal models in that the hydrotherma: system which produced mineralization was active in a shallow water marine environment. The Red Rock Deposit has a resource of 180,000 tonnes of 66g/t Ag and 0.9 g/t Au, and a Ag:Au ratio of 70:1. Mineralization is largely associated with hydrothermal brecciation, and occurs as disseminations, vein stockworks, and struc- turally controlled lodes. Ore minerals comprise acanthite (argentite), electrum, native Ag, Ag- sulfosalts and base metal sulfides, Alteration minerals associated with ore are quartz, cal- cite, adularia, pyrite, illite, illite-mont- morillonite, chlorite and sphene (leucoxene). Illitic and propylitic alteration zones sur- round the hydrothermal breccia. Bulk rock analyses indicate that alteration is character- ized by the addition of Si, K, Fe, Mg and the loss of Na and Ca. Ore was deposited from a boiling fluid in a temperature range of 222- 295¦C, and of 0.5-7 wt. Z NaCl equivalent sal- inity. An upper hydrostatic depth limit of about 800 m is implied for the boiling fluid ii an open vein. Sulfur isotopes indicate a mag- matic sulfur source, and oxygen isotopes imply a predominantly marine ore fluid. Modern analogs of the submarine hydrothermal system that formed the Red Rock Deposit occur in the Taupo Zone, New Zealand, and southern Kyushu, Japan.

Jan 1, 1987

By K Williams

Marvel Loch South Pit has had a number of stages of open and underground mining activities before acquisition by Sons of Gwalia. The historical pit had achieved a completed pit depth of 150 metres and the shaft and decline mine had reached approximately 220 metres in depth using open stope mining methods. The various mining methods reflect the various economics and industry practice at the time. The South Pit ore zones are medium grade (~2.5 g/t) but have a regular geometry and large tonnes per vertical metre. A number of studies have been completed up to a pre-feasibility stage looking at options to extend the pit depth and to lower the unit cost of gold production. The options considered were the re-optimisation of the pit to determine further cutbacks or the innovative use of an in-the-wall ramp. The in-the-wall ramp (tunnel) would permit the removal of the in pit ramp to expose additional ore that was within the footprint of the ramp design and to provide the opportunity to increase the final pit depth. Similar mining method has only been used at Three Mile (Coolgardie, WA) and Chalice Mine (Norseman, WA). The tunnel would serve as a gateway for further extension of the south mine and the central ore zone via underground mining methods. The ultimate depth of the South Pit has been extended to 310 metres below surface and significant additional ore has been recovered. This paper will give an insight into the various studies to optimise the Tunnel mining method, the determination of the various tunnel dimensions, and the phases of mining to arrive at the completed design.

Jan 1, 2003

By C McMahon, S G. Walters

Mineral maps of æintactÆ and large particle textures have been produced routinely from optical microscope images. Polished thin sections of large particles (1 - 3 mm) provide a balance between representative sampling and the preservation of primary rock textures. Optical microscopy is an efficient way to generate mineral maps suitable for geometallurgical applications. The automated optical mineral identification was carried out using a Leica DM6000¬ microscope with a high precision stage suitable for direct tiling of image frames and good registration of multiple image layers. Standard images collected were 10 x 10 frames (20 mm x 16 mm). Four image layers were recorded: ætransmitted light plane polarisedÆ, ætransmitted light crossed polarsÆ, ætransmitted light crossed polars with 1l tint plateÆ and æreflected lightÆ. All image analysis was carried out using Definiens Professional V5¬. The four image bands were read directly in 12 greyscale bands. A segmentation algorithm produced objects based on homogeneity across all bands. These objects were then classified using a complex set of rules (Process Tree) that are based on image brightness in all 12 bands. Opaque and non-opaque minerals were classified in the same sample. Using this protocol up to 12 minerals can be satisfactorily classified in one sample. The opaque minerals were recognised using colour ratio and reflectance intensity in the reflected light image. Non-opaque minerals are more difficult because of the complex variable colours of many minerals and the complexity of interference colours. However, object-oriented classification using three transmitted light image layers and multiple rules is a powerful technique for recognition of these minerals.

Jan 1, 2008

By L S. Barbour, M K. Meiers

Soil covers for mine waste are subject to changes in structure as a result of root development, and wet/dry or freeze/thaw cycling. The purpose of this study was to evaluate the changes in the hydraulic conductivity of three non-compacted clay covers over time. The covers are located on a sodic/saline overburden fill (30-Dump) at the Syncrude oilsands mine in Fort MacMurray, Alberta, Canada. Monitoring of these covers for temperature, matric suction, and water content by the University of Saskatchewan has been ongoing for more than three years. The three covers (D1, D2, and D3) were constructed in 1999 and are 50 cm, 35 cm, and 100 cm thick. The covers are comprised of a surface layer of reclaimed peat/mineral mix over a secondary reclaimed mineral soil (glacial till or glaciolacustrine clay), placed over a sloping shale surface. Field measurements of hydraulic conductivity within the secondary layer were obtained using a Guelph Permeameter during the 2000, 2001, and 2002 summer field seasons. Repeated measurements were made within the D1, D2, and D3 covers at depths of approximately 40 cm, 30 cm, and 60 cm, respectively. The values of hydraulic conductivity for the covers were similar to each other during each of the field study seasons. The mean hydraulic conductivity of the secondary layer increased every year: 2.5 + 10-6 cm/sec to 2.1 + 10-4 cm/sec to 4.3 + 10-4 cm/sec from 2000 to 2001 to 2002. Soil temperature data shows that one freeze/thaw cycle occurred each year at the measurement depths.

Jan 1, 2003

Citigold Corporation operates the Warrior gold mine at Charters Towers, northern Queensland, mining narrow quartz veins (0.1 to 2 m wide) in granodiorite by long hole open stoping on levels 15 m apart. Access is by decline and cross-cuts with on-ore development drives. The mineralisation comprises Palaeozoic mesothermal quartz veins containing gold, pyrite, sphalerite and galena, hosted by the Ordovician age Towers Hill Granite. The gold grain size is variable from 1 to 500 ¦m with 1 m face samples up to 800 ppm Au, and average run-of-mine grades of 10 to 14 ppm. Despite the spectacular gold tenor, little visible gold is present. Gold grades are highly variable presenting challenges in ore reserve estimation. Tonnages are discounted by 70 per cent to allow for the low payabilities (30 to 50 per cent) of the veins. Estimation techniques allow high confidence in overall global grade estimates but poor reliability on a local scale (25 m). Kriging ranges as low as 5 - 8 m means that obtaining a Proved Ore Reserve by diamond drilling is not economically feasible, and broad-scale mine planning decisions are made at the Inferred Mineral Resource stage and mine design work at the Probable Ore Reserve stage. Proved Ore Reserves can only be estimated after underground development has proceeded through the mineralised body with levels at 15 m vertical spacing sampled at 2 - 3 m intervals along the level. However, reconciliations between actual gold produced and earlier resource estimates produce workable results. A further three mines are scheduled to be developed underneath the city of Charters Towers.

Jan 1, 2008

By Somerville M, Muray A, Bocking M

Australia has an extremely large total hot dry rock (HDR) resource above a depth of 5 km, equivalent to 7500 times its present annual energy consumption, of which 80 per cent underlies the Great Artesian Basin. The resources most likely to be exploited first are those residing in homogeneous granitic bodies beneath sedimentary basins containing insulating rocks such as shales and coal measures. In the Sydney Basin south of Muswellbrook, an area of high geothermal gradient corresponds to a gravity low thought to be a buried granite body at a temperature of possibly 250¦C. This locality is suspected to have the ideal geological characteristics for Australia's first hot rock test facility. Australia's high HDR potential is possibly unique in the world, in that the potential sites satisfy four independent, geological conditions, each considered as favourable for the creation of a resource, and for the ease of extracting that resource. They are: ò Higher crustal heat generating capacity than that of normal continental crust. ò Much of the Australian continent is covered by sedimentary basins which contain a high proportion of shales and coal measures that have low thermal conductivities, thus providing an insulating blanket for the heat being generated beneath. ò The sedimentary basins are in many places underlain by large untectonised granitic bodies that are not only a major contributor to heat generation, but also ideally suited to the establishment of HDR reservoirs. ò The crustal shortening stress field that is found in the majority of the Australian continental crust results in a vertical minimum principal stress orientation which should result in the development of favourably oriented horizontal stimulation cells necessary for maximising an HDR resource.

Jan 1, 1995

Evidence for Middle-Late Triassic large-scale, silicic volcanism characteristic of extensional continental terranes is widespread in the Tasman Orogenic Zone in Eastern Australia. Detailed study of an area of south-east Queensland has defined the eroded remnants of a large collapse caldera and an associated area of rhyolite dome building and regional downsag which may be a second caldera (Stephens, 1986). The silicic volcanics and minor basaltic to andesitic products have been assigned to the Aranbanga Volcanic Group (Cranfield, in prep.) and the associated granite complex has been named the Mungore Complex (Ellis, 1968). Published isotopic age dates on the Mungore Complex are 212-219 m.y. (K-Ar Biotite; Ellis, 1968) and 226 m.y. (pooled Rb-Sr on several similar plutons in the region; Webb and McDougall, 1967). Basalts within the area have been dated at 219 m.y. (GSQ Annual Rpt., 1986). The collapse caldera (Mungore Caldera) lies on the intersection of 4 major structural features: 1) the Mt. Perry Lineament, a meridional fault zone extending for over 600 kilometres in a NNW-SSE direction and which has faulted the eastern part of the caldera 5 kilometres sinistrally. The lineament has been active at least from mid-Permian to Late Triassic and has localised activity into the Tertiary. Granite plutons of the same age as'the Mungore Complex- are topographically prominent and largely concentrated east of the Mt. Perry Lineament and its extensions (Nash, 1986); 2) the extension of the Darling River Lineament, a continental-scale, ENE trending feature which correlates with regional structural discontinuities but which lacks expression as faults within the Tasman Orogenic Zone;

Jan 1, 1987

By E R. Ramanaidou

Two unknown iron ore samples were found by a geologist from Ok Tedi Mining Limited copper, gold and silver mine at an old wharf site dedicated to a 1970s drilling program in Lake Murray in Papua New Guinea (PNG). These iron ore samples could not come from a PNG mine and it was decided that a study should be undertaken to understand their origin. Lake Murray is the largest lake in PNG with a total surface area of 647 km2. It has a high-water 2038 km long convoluted shoreline with seasonal water level changes (Osborne, Kyle and Abramski, 1987) and it is located around 200 km south of the Ok Tedi mine (5°13’25”S, 141°09’37”E). The petrology, mineralogy and chemistry of two Fe samples (Ok Tedi 1 and Ok Tedi 2) included optical microscopy, X-ray fluorescence (XRF) analysis and a comparison with worldwide iron ore deposits. The two rock samples were cut to produce two subsamples: (1) a polished thin section; and (2) a pulp that was used for XRF analysis including major, minor and trace elements. Ok Tedi 1 and Ok Tedi 2 were petrologically and chemically compared to a range of known iron ore samples from Australia, Brazil and South Africa. The petrological study of Ok Tedi 1 indicates that it is composed of granoblastic recrystallised hematite and the overall texture is uniform without any obvious original ‘sedimentary’ texture. Ok Tedi 2 is a ‘specular’ or platy hematite with recrystallised and fused grains. Using both petrological and chemical clues, the two Ok Tedi samples likely originated from the Iron Quadrangle in Brazil.

Sep 18, 2023

By J Naude

The TauTona (Sotho for Great Lion) Mine near Carletonville, which is one of AngloGold AshantiÆs most profitable operations in South Africa, has started a multi-million dollar expansion project that is expected to extend the operational life of the mine by at least three years. The project will also secure some 1900 jobs for existing workers and contract workers. The $US140 million project entails the development of the orebody to a record depth of almost 4 km underground. It means that TauTona, which already mines gold at the deepest levels in the world, will deepen its mining activities from 3600 m to a new record depth of 3910 m. There is great anticipation about the expansion program, especially because of new technology that will contribute to a safer working environment. It includes a simplified hoisting system that will minimise safety risks in conveyance activities. Due to the unique nature of this project, depth below surface and working through a three-tier shaft system, various innovative measures were incorporated into the planning of the endeavour. Special support equipment was designed to reduce cycle times and enable the crews to install the extensive support, prescribed by the mineÆs rock engineering department, right up to the face before every blast. Both declines dip at 23¦. The personnel/material (P/M) shaft is 4.4 m wide x 3.9 m high. This shaft is unique in that the conveyance will have an onboard driver. The rock shaft is 4.5 m wide x 3.6 m high. Rock will be hoisted with two, ten-tonne overturning skips. In both cases, P/M and rock, the winders were designed for the highest duty cycle, which is encountered during sinking.

Jan 1, 2005

Truly launched during the 1939-45 war, b¬,osted since by huge increases in demand for food, shelter and manufactures of ill kinds, petrochemicals have rocketed into prominence' all'oVer''th'e world and are accelerating to even greater heights.Manipulation of the hydrocarbons in petroleum or natural gas provides raw materials for a wid.e'variety of plastics, resins, detergents, rubbers, chemical intermediates, fibres and fertilisers. These in. turn.. go into a host of products essential to our way of life.A5 a source of chemicals, petroleum has achieved a high place. because of its abundance, relative.eheapness acid ease "f transport and because it can,be' economically processed.'If a nation's industrial' progress is measured by ' the ' modern yardstick of petrochemical production,'Australia has reasonto be proud, for it now has 1S petrochemical plants worth'156 million, either in operation or under construction.At several locations near Sydney and Melbourne, these plants produce petroleum ethylene, propylene, butadiene and benzene, or convert these building blocks into the three major thermoplastics (polyethylene; polyvinylchloride and polystyrene)-a.nd"S.B.R.synthetic" rubber. "A number bf other imr-ortant petrochemicals, including carbon black, and ammonia, also are made, or-planned...Most petrochemicals find application. in seven principal industries - rubber, fibres, detergents, surface coatings, automotive, agriculture and plastics. They play a .part in many other industries, including mining and metallurgy.In Australia, population growth,.an -incr.easing standard of living, greater industrial activity and the replacement of older materials all should considerably expand the markets for established petrochemical plants and lead to the introduction of new manufactures.Unless thwarted, these positive forces should propel petro-chemicals into a future glittering with promise;' ò 'However, some help for the infant industry seems needed if petrochemicals, while growing with the nation, are to contribute as they can to our national development.

Jan 1, 1962