Search Documents

The comminution process indicates that the most energy-efficient comminution system would be one where the particles leave the breakage field as soon as they reach product size. Contrary to the free falling gravitational (vertical) flow in crushers, the grinding millÆs energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of a pulp lifter is to transport the broken material and slurry from the discharge grate out of the mill. Hence, the design optimisation of pulp lifters affects not only the energy efficiency and throughput of autogenous grinding/semi-autogenous (AG/SAG) grinding mills, but also contributes other process benefits such as improved wear life and operator-friendly steady and smooth mill operation. Following its introduction in 2006, OutotecÆs patented Turbo Pulp Lifter (TPLÖ) design has been retrofitted at existing sites and also installed in some new ones around the world. This paper will provide operational experience and data on how the TPLÖ design has allowed AG and SAG mills to operate efficiently.

Jan 1, 2009

Investigation on Sheelite Floatability by Particle Size Fraction

Sep 13, 2010

By M Kilburn, A Edenton, M Adam, A Dehghan-Manshadi, R Smyth, L Lu

The blast furnace is a counter current reactor. The counter current principle of the furnace makes it very efficient in transferring the heat and mass required to drive the reduction reactions inside the furnace. However, this does impose a stringent requirement on the permeability of burden material in the furnace. Lump ore is one of the key ferrous feeds used in the blast furnace ironmaking process, often accounting for ten to 20 per cent of the blast furnace ferrous burden. As the lump ore descends through the blast furnace, it is dried, heated and reduced by the ascending hot reducing gas. To ensure good furnace permeability, generation of fines from burden materials including lump ore due to mechanical, thermal and chemical processes needs to be minimised. Unlike sinter and pellets, lump ore is subject to thermal degradation. To assess this behaviour of lump, the ISO decrepitation test (ISO 8371, 2007) is often conducted, and the result is calculated as a decrepitation index (DI). However, the DI values obtained from the existing ISO decrepitation test vary considerably between test portions and between laboratories, which makes meaningful comparison very difficult. In order to identify the sources responsible for the unacceptable repeatability, the effect of various testing conditions, such as particle size, heating rate, sample preparation and loading method, on the mean DI value was studied. The mechanisms contributing to thermal degradation in the top of the blast furnace and during the standardised decrepitation test are also discussed.CITATION:Lu, L, Kilburn, M, Dehghan-Manshadi, A, Adam, M, Edenton, A and Smyth, R, 2013. Thermal degradation of lump ore in the top shaft of blast furnaces, in Proceedings Iron Ore 2013 , pp 421-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The production of synthetic crude oil requires a suitable coal or a coal extract modified by hydrogenation for pyrolysis. Existing classifications are broadly based on historical and current needs. One, Seyler's, is based on a visual display which can be used to present petrographic bounds. The analysis of the coal extracts from solvent hydrogen-donor testing allows an experimental limit to be described and a plant limit to be indicated. Australian black coals are discussed within these petrographic and plant bounds and their limitations as a feed for the production of synthetic crude presented. Potential uses for the aromatic liquid products are suggested. The application of the diagram as a screening procedure for sub-hydrous coals is described.

Jan 1, 1975

Vaal Reefs Mine annually produces some 75 tonnes of gold. Stoping operations, using a scattered mining method, are conducted on several reef horizons within Witwatersrand Supergroup metasediments of the Klerksdorp Goldfield. Current grades average 7.19 g/t Au over a 133cm stoping width. The reef horizons, of which the Vaal Reef is the most important, consists of 2.9Ga palaeoplacer deposits at the base of low angle unconformities. Typically, a reef comprises a mature quartz and chert conglomerate with a siliceous matrix and intergranular pyrite and carbon. Geologists are primarily responsible for underground mapping and supervising of drilling programs. To a lesser extent they are involved with sampling, grade control, ore reserve estimation, mine planning and rock mechanics. Due to a general decline in grades of gold mines, an escalation of production costs, and with the current weak gold price, it has become essential to improve production efficiencies. Consequently the role of the mine geologist has moved away from that of simply keeping the mining people "on reef'. Greater emphasis is being placed on refining geological models to assist in selective mining of the reef and investigations of secondary reef horizons are encouraged. Exploration within fault losses and re-evaluation of pillars is important, and geologists are becoming more involved with sampling and grade control exercises.

Jan 1, 1990

By Cortes JP

In a dynamic environment such as the Star Mountains of Papua New Guinea Geotechnical Engineering for the Ok Tedi Project must be described as both interesting and challenging. To be effective a reasonable sized team of dedicated people is required with occasional supplementation by specialist consultants and an annual review process. Ok Tedi Mining Limited's (OTML) Geotechnical Section has a vision to be recognised as the leading mine-based geotechnical engineering section in PNG and to be world class by any international standards. This paper deals with the organisational and operational duties of the Geotechnical Section at the Ok Tedi Mine. One of our major roles is in the area of safety, and in particular in the early warning of natural and mining induced geological hazards that may affect safety and/or productivity. The major activities in- clude geotechnical inspections (pit, waste dumps, tunnels, re- gional), data collection activities and database management, geotechnical design and control work.

Jan 1, 1997

The influence of pulp potential on the flotation behaviour of sulphide minerals in laboratory batch flotation tests is discussed in terms of self-induced flota- tion, collector-induced flotation, and depression.' Assuming that the pulp poten- tial is controlled by the same factors that determine the genuine redox poten- tial, an attempt is made to interpret the experimental results in terms of potential-dependent reactions based on bulk thermodynamic data. Self-induced flotation is displayed by many sulphides in moderately oxidizing solutions but not in reducing solutions. The available evidence suggests that the hydrophobic entity could be sulphur produced by superficial oxidation of the mineral but this has not been established beyond dispute. In general, flotation is observed near the potentials at which sul- phur would be expected to form and the minerals which produce sulphur seem to float the most strongly. Collector-induced flotation is most conveniently studied on minerals which have only slight self-induced floatab- ility. The mineral-collector interaction is potential-dependent hence flotation is generally only observed in limited ranges of potentials. While the general form of the floatability-potential relationship is similar to that predicted from thermody- namic data close correspondence between predicted and experimental results is not always observed.

Jan 1, 1984

By R-H Yoon

Increasing the upper particle size limit of flotation would allow operators to increase mill throughput, save operating costs, simplify flow sheets, and increase rate of return. However, coarse particle flotation is difficult for various reasons, of which bubble-particle detachment has been identified as the major limiting factor. In the present work, the process of bubble-particle detachment has been studied by directly measuring the forces required to detach air bubbles from hydrophobic solids. The measurements were conducted using a hanging balance apparatus. The measured forces were converted to detachment energies that can be compared with the work of adhesion, which in turn is a function of hydrophobicity, surface tension and contact area. The results were converted to detachment energies using the Young-Laplace equation for capillarity. In the present work, the solid surfaces were hydrophobised by coating them with octadecyltrichlorosilane and cetyltrimethylammonium bromide. The results show that bubble-particle detachment occurs in two steps. In the first step, air bubbles are deformed, while the three-phase contact (TPC) line is pinned, until contact angle reaches advancing angle. In the second step, the TPC line moves along the surface until solid/air interface is replaced by solid-liquid interface. In general, the energies of detachment measured in the second step are in good agreement with calculated work of adhesion. Thus, the energy required during the first step effectively represents an energy barrier for bubble-particle detachment. It has been found that the energy barrier varies with surface roughness and surface tension. The results of the present investigation suggest, therefore, that coarse particle flotation can be improved by control of particle hydrophobicity, surface roughness, and surface tension.

Jan 1, 2005

By Burks WG, Hughes FE, Muceniekas E, Whitcher IG

The area containing the iron field, recognised by the writers, is part of an uplifted, portion of the 'Western Australian Plateau,' ranging in elevation from about 1,000 feet to about 3000 feet above sea level. The local rock succession is flat-lying or moderately-folded and belongs to the Nullagine Series of Upper (2). Precambrian age. This series forms the Hamersley Rangeland vast portions of the...

Jan 1, 1964

By Misra A

The development of roadways in underground mines in Autralia is by conventional continuous miner technology. The rate of development achieved using this technology is improved by modifications to this technology using additional equipment such as surge cars or decreasing roof bolting time.Development rates achieved with this technology compare with developing technologies such as high capacity continuous miners, continuous transportation and simultaneous cutting and bolting systems such as the Kemcol Beaver. Pillar dimensions have an effect on the rate of development.'

Jan 1, 1991

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

By Molloy GR, Eaton RA

The crusher development programme for 7ft Super Extra Heavy Duty (SXHD) Symons cone crushers commenced in 1984. The main objective of the programme was to run the crushers at maxi- mum power for the full life of the liners. This would give a finer product sizing enabling grinding and flotation plant throughput to be maximised. The study was conducted along two basic lines of attack, the first main- taining an effective profile through the life of the liners, the second improv- ing the properties of the liners. It has been found that crusher liner life can be extended and crushing efficiency improved by modification of liner composition and profile.

Jan 1, 1988

The problem of manufacturing from sulphuric 'acid and Christmas Igland "A" phosphate, superphosphate of acceptable physical condition and agronomic phosphate availability, is directly related- to the crystallisation of a reac- tion product, monocalcium phosphate monohydrate. Two solutions to the problem, vacuum drying the superphosphate and calcination of the ore before reaction with acid, are discussed.

Jan 1, 1971

By D Dickson

The properties along Ida Avenue in Mosman stand 10 m above the road on an outcrop of Sydney sandstone. Access to the houses is generally via a long steep staircase. The owner of 22 Ida Avenue identified an opportunity to use the natural strength of the rock beneath his property to excavate an underground garage and to provide access to the basement of his property via a 10 m elevator shaft from the back of the garage. This paper will describe the design and construction of this unique and innovative urban development.

Jan 1, 2008

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

By Stanton RL

Stratiform lead-zinc mineralization in the Soldiers Cap Group and Kuridala Formation of the Mount Isa Inlier is closely associated with iron-rich sedimentary units or "iron formation", and has many similarities to the Broken Hill deposit in New South Wales. Both the Soldiers Cap Group and the Kuridala Formation have been intensively explored for deposits of this type since the early nineteen- seventies. A mineralized belt of at least eight significant prospects has been identified, of which the Pegmont deposit is the largest and best known example. In most cases the mineralized horizons contain banded galena and sphalerite within a gangue of predominantly quartz-garnet- pyroxene-amphibole rock, sometimes containing a variety of other metamorphic silicates, and apatite. Chemically, the mineralized horizons are distinguished by higher than usual levels of one or more of total Fe, MnO, CaO and P205. Interpretation of patterns of mineral- ization within the belt is based on the Pegmont deposit, where a model of base metal sulphide deposition within restricted basins of iron-rich chemical sediment has been developed (Stanton and Vaughan, 1979). Broadly, the model envisages the deposition of higher grade lead-rich mineralization in the basin centre position, lower grade zinc- rich mineralization in a basin intermediate position, and much weaker copper-rich mineralization in a basin edge position. These three positions reflect a laterally continuous arrangement of silicate microfacies within the original iron-rich sediment.

Jan 1, 1984

The interfaces between the Broken Hill ore lenses and the enclosing wallrocks are, on a broad scale, parallel to metamorphic layering in the wallrock gneisses and quartzites. In detail, however, the concordant contacts are interrupted by piercement structures, formed by plastic injection of ore into the wallrocks during metamorphism.These discordant bodies vary from minor projections measuring less than I m long, to major ore shoots ("droppers") as much as 60 m long. The intrusive bodies consist of fragmented ore and wallrock in amatrix of recrystallised sulphides. Wallrock fragments have been altered to manganese-rich and calcium-rich mineral assemblages. The injected ore is enriched in sulphides compared with the parent ore, and there has been enrichment in a number of minor elements.Piercement structures formed during the waning phase of high grade metamorphism, when incompetent ore was injected plastically under pressure into the wallrocks, particularly at fold crests. Adjacent to the "droppers", retrograde schists developed as a result of shearing along the ore-wallrock interface.

Jan 1, 1976

By Yesil MM, Bozdag T

This paper describes the conver- gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu- sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

The Mobile Miner MM130 was delivered to Broken Hill in February 1992. During March the machine was extensively trialled on the surface to test manoeuvrability, climbing ability and muck handling prior to being trammed underground in April. The first cutting test on 30 April 1992 provided promising results. The machine has undergone continual development since it arrived in Broken Hill with aims of ensuring reliability and achieving performance goals. The paper gives a detailed account of recent performance comparing this with the predicted Performance.

Jan 1, 1993