Search Documents

By Nowell SB, Cottrill DA

Host-rock - wallrock major and trace element geochemistry associated with epithermal gold mineralisation in the Hauraki Goldfield of New Zealand is poorly documented, even though rock geochemistry is a recognised tool in exploration. Such responses assist in recognition of the regional scale imprint of fossil hydrothermal activity, and indicate targets for detailed evaluation within these alteration zones.Recent investigation of gold deposits in the Waihi (Gladstone), Golden Cross (Empire), Thames (Waiotahi) and Coromandel (Tokatea) areas indicate enrichments of Au, As and Sb in the andesitic wallrocks hosting mineralisation. Of the other elements examined, Si, K and Rb are enriched, and Na, Ca, and Sr are depleted at all deposits. These trends are best developed in the vicinity of veining. In deposits with clay alteration dominating (Waiotahi and Tokatea) there is also depletion of Mg, Mn, Zn and Cu. Ba and Cr are variably enriched or depleted within different styles of alteration. Base-metal enrichment in the wallrocks is not a feature of Hauraki deposits.

Jan 1, 1990

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003

By A Keddie

Standard microeconomic theory suggests that the behaviour of mineral extraction and processing firms with respect to their demand for water can be modelled and a market demand for water subsequently derived. Such a model, although an abstraction of the real world, should be able to predict the responsiveness of quantity of water demanded to change in price, and, change in demand to a range of factors including: expectations about reliability of supply, changed commodity prices for mineral production, and change in water technology and storage at mine site. This paper demonstrates that the price of water is particularly responsive to changes in demand and that although price increases would result in some additional supplies, physical constraints on supply suggest that the industry will be paying considerably higher prices for water in the future. It is recommended that the mining industry undertakes quantification of possible price increases to position itself to minimise the impact on their operating costs as well as to make responsible capital investment decisions to facilitate future expansion or commissioning of new mines. Substantial investment is required to commission a new mining venture with expected rates of return subject to risk and uncertainty due to fluctuations in world commodity markets as well as reliability of secure supplies of inputs. If a reliable supply of water was subject to uncertainty and water was a critical input for production, then the initial mine design would typically consider a range of production decisions contingent on levels of uncertainty with respect to water supply. These states or sets of water supply, will affect production decisions and future water demand. Modelling production decisions contingent on different states of nature, termed the state-contingent approach, provides a number of insights about producer behaviour under uncertainty. This paper investigates the assumptions underlying the derivation of the market demand for water by the mineral resource industry and identifies the drivers of demand and the responsiveness of the industry to change in price and supply, particularly in relation to capital investment in water-use technologies. The usefulness of these models to the mining industry is considered by reference to the increasing demand for water by the industry in Queensland, in a climate of water shortages.

Jan 1, 2006

By W van der Westhuizen

Mining professionals recognise the need and application for reconciliation and value tracking. It is necessary however to examine our current reality, and evaluate the following. Do our reconciliations really balance correctly, and are we able to track value effectively throughout processes? If we are honest, in most operations the answer is a resounding no. This means that we are surrounded by fluctuation and deviations that we do not account for and do not understand. This is astounding, because given our level of scientific knowledge and the technological tools at our disposal we should have a good understanding of our environments and be able to manage them effectively. How do we manage effectively if we are surrounded by so much uncertainty? The purpose of this paper is to describe, at high level, the principles of reconciliation and value tracking, to highlight some areas where deviations are introduced into the mining process, and to propose a different approach to the apparent reconciliation and value tracking conundrum. The paper also poses several questions that need to be critically addressed at most operations. Instead of making the same mistakes each month in reconciliations, mining professionals need to acknowledge two facts. Firstly there will be uncertainty that we need to accept, since all our estimates are based on sampling, an orebody is not homogeneous and peopleÆs behaviour will influence the process, etc. Variability will always exist and lead to uncertainty. What is the current approach in the reconciliation process when a deviation occurs and how do we use reconciliation and value tracking to manage and improve our business? The second fact is that we need to stop using reconciliation and value tracking to only measure and report. We need to adopt a new approach to manage mining throughput, where reconciliation and value tracking are enablers to the success of the business. In most mining operations, significant effort goes into planning and measurement for the purposes of reconciliation and value tracking. The importance of accurate and effective reconciliation and value tracking should be to ensure the maximum utilisation of the resource, maximising throughput and enabling the business to deliver a product to its client, of the correct quality and in a timely manner.

Jan 1, 2002

By Khosrowshahi S

The objectives of grade control remain unchanged but new methods are being developed to attain them. Since the early-1990s, an improvement in the power of mine site computers has made the geostatistical tools of conditional simulation more accessible. Optimisation of the grade control process on mine sites now involves two stages: optimisation of the sampling regime and optimisation of the interpretation of ore and waste boundaries. Optimisation of the sampling regime first requires an understanding of the nature of the mineralisation and in particular the impact of particle size on the sampling precision. This relationship, termed the Fundamental Error of sampling, enables an optimum subsampling protocol to be defined for the sample preparation and assaying. However, the actual sample collection method, whether drilling or trenching, must be correctly selected and the sampling grid should be optimised. The relative costs and benefits of various alternative sampling methods and grids can be determined using the method discussed. The use of the grade control data can also be optimised. In the past ore and waste boundaries were often defined using a linear interpolation algorithm that smoothed the data (such as polygonal, sectional, inverse distance squared or even kriging methods). Frequently the relative impact of ore loss and dilution could not be estimated. Conditional simulation to generate equiprobable alternative maps (realisations) can now be adopted to address these issues. A transfer function is then used to evaluate the similarities and differences between the maps. The Ore Block Optimisation (OBO¬) process is a transfer function that produces a three-dimensional model of the optimal ore block outlines. This provides a clear guide for the mining geologist to refine and mine. The nature of the transfer function and the inputs and outputs are discussed. In the past, reconciliation has been the `acid test' for any grade control system. Any ore blocking method based on conditional simulation can make use of the exhaustive data set to ensure that reconciliation between prediction and production will improve significantly. The OBO¬ method provides a guide to the mining geologist to ensure that the best ore blocks are mined. Misclassification between ore and waste is reduced, ore loss and dilution are minimised (and are measurable) and ore is optimally assigned to stockpiles of various cut-off grades. These advantages significantly enhance mine profitability and control of the mined grade.

Jan 1, 1997

By I D. Hair

A numerical groundwater model was used to predict the nature of interactions between heavy mineral sands mining operations and the groundwater regime at North Stradbroke Island, Southeast Queensland. North Stradbroke Island is formed mainly of massive vegetated Cainozoic aged dune sands. Since the 1950s, a number of operations have mined rutile, zircon and ilmenite on North Stradbroke Island. In such mining operations, a dredge and an associated processing plant are floated in a pond either above or below the prime groundwater table The numerical model was based on the North Stradbroke Island Groundwater Management Model, developed in 2001 by the Department of Natural Resources and Mines (NR&M). This model was constructed using the modular, cell-centred, finite-difference groundwater flow model, MODFLOW, developed by the United States Geological Survey (USGS). The NR&M model was refined to improve model resolution and detail for simulating dredge mine paths. Of particular interest were: water table fluctuations induced by mining for the identification of slope stability risk; the optimisation of sand spear arrays supplying mine make-up water requirements; inflow and outflow rates to the dredge pond for overall mine water balance; and interactions with Eighteen Mile Swamp and water supply bores controlled by the Redland Shire Council (RSC). Depending on the water level in the dredge pond compared with the surrounding groundwater table, water either flows out of the dredge pond into the groundwater regime or from the groundwater system into the dredge pond. The MODFLOW river package (RIV) was utilised for the modelling study. Dredge pond movement was simulated using specialised software developed by Watermark Numerical Computing (WNC) to interpolate pond positions and map the dredge path to the model grid both spatially and temporally. As tailings placement affects the groundwater system through increased recharge, the MODFLOW recharge package (RCH) was utilised to simulate different recharge efficiencies. Long-term model predictions were made for the period from July 2002 to May 2021. Results of the modelling showed that exchanges of flow between mining operations and the groundwater regime could be effectively managed. The study provided valuable information which was used to develop an appropriate mine water management plan.

Jan 1, 2003

Acclaimed as one of the most remarkable orebodies anywhere on account of its length and richness, the Oroya Shoot occurs on the eastern side of the Kalgoorlie gold mining district close to the contact of a fine-grained with a coarse-grained greenstone, and in association with sediments. In the same stratigraphic position on the synclinal flanks of a large drag fold there are a number of other flat ore pipes, smaller, but almost as rich in tenor. Although differing in control structure they are believed to be related genetically as all show a characteristic development of a bright-green ore known locally as "green leader". Folding and bedding structures have played an important part in formation of the ore shoots.INTRODUCTIONThe Oroya Shoot is the biggest individual bonanza of Kalgoorlie's Golden Mile. It has been stoped almost continuously over a length of 4,300 ft., and about 2,000,000 oz. of gold have been won from it. Naturally pillars are not left in the best sections of such an orebody and the detailed geology of stoped out portions can only be inferred from examination of adjacent workings.No mention is made in the literature of the actual makeup of the orebody although a few structures are shown on some of the old cross sections. A diagrammatic cross section, Fig. 1, adapted from Stillwell (1929) illustrates the form of the Oroya Shoot.Gustafson (1937) drew attention to the role of folding, previously unrecognized, in Kalgoorlie geology, and indicated that the Oroya Shoot is associated with a minor drag fold on the east limb of the Brownhill Syncline, itself part of a larger left hand drag on the Central Anticline. The latter in turn appears to be part of a regional right hand fold system as shown by Campbell (1953).

Jan 1, 1959

By K Gilliland

The past decade has seen the widespread implementation of computerised real-time operational management systems in open pit mines. While these systems have made a significant impact on operational efficiency at a process level, surprisingly little work has gone into integrating these systems with other IT systems, including those used for tactical planning and enterprise resource planning. As a result of this gap in the information hierarchy, the goal of optimising an entire operation, or multiple operations, remains elusive. Implementation of computerised operational management systems in underground mines has been much slower. This is a significant, though often overlooked, reason why the productivity for underground mining is generally so much lower than for open pits. The historical reluctance to implement computerised operational management systems underground can in part be attributed to the underground environment, particularly the difficulty in establishing effective communications. Another factor retarding the implementation of systems underground has been the perception that the nature and scale of underground mining does not lend itself to computerised operational management. This perception can be challenged, not only by a process level examination of the underground mining, but also by a holistic examination of the entire industry. In recent years, the mining industry as a whole has destroyed rather than created wealth and underground mines are major culprits. The degree of value destruct has been more pronounced with underground mines, as the usual problem û low commodity prices û has been exacerbated by the harsh environment, low productivity and a æfog of warÆ no longer generally found in open pits. Faced with these realities, underground mines will have to adopt modern management tools or suffer extinction at the hands of an unsympathetic investment community. All is not gloom and doom, however. Technological advances have largely overcome the difficulties associated with the underground environment. As a result, there is a small, but growing, number of underground mines using computerised operational management systems to directly improve the bottom line. Much greater improvements can be realised if the industry takes advantage of the recent convergence in technology, to integrate process information with tactical and enterprise resource planning systems in order to provide a solid platform for all decision-making. This would result in the æeÆ mine. Given that the underground fraternity is essentially starting with a blank sheet, they have the opportunity to æsteal a marchÆ on open pit mines, who may be constrained by legacy systems. The benefits of the æeÆ mine are presented through a hypothetical case study that examines the shortfalls of the non-æeÆ mine. The paper ends by presenting a future vision for the æeÆ mine.

Jan 1, 2000

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By C J. Berry, P H. Briggs

Assessment of metal mobility, acid rock drainage production, and toxic effects from weathering of mineralised materials (ie mine-waste piles and outcropping alteration/ore zones) is key in evaluating and mitigating metal mining sites. Many metal- and acid-generating materials at these sites are sulfur minerals (sulfides to sulfates) with differing reactivities, weathering characteristics and metal contents. Our working hypothesis predicts that data on the types and quantities of sulfur minerals, coupled with comparison of their sulfur isotopic compositions to that of aqueous sulfate in the surrounding environment, can be used to evaluate primary pathways of weathering reactions at mining sites. We developed a sequential extraction scheme to separate the phases of sulfur in mineralised materials. Operationally defined phases, including monosulfides, disulfides, elemental sulfur, water-soluble sulfo-salts, acid-soluble sulfates, and resistant sulfate phases such as barite, are quantified gravimetrically and/or instrumentally. Several sets of experiments were designed to test the effectiveness of this extraction scheme. First, a variety of ore sulfides diluted in an inert matrix was analysed with the scheme. Results showed that molybdenite and arsenic-bearing sulfides do not behave as predicted from just their sulfur oxidation states, indicating that samples containing these minerals need special treatment for complete phase recovery. Second, a natural mine-waste composite standard was analysed by the scheme. The sum of the phases was equal to the total sulfur concentration analysed independently. Each phase had a similar, but distinct sulfur isotopic composition. The results were verified with a laboratory prepared æproxyÆ having the same mineralogical composition as the standard, but with each phase having a very different sulfur isotopic composition. The sulfur isotopic compositions of the recovered phases from the æproxyÆ showed that the scheme effectively separated the sulfur with only minor cross contamination of phases. The speciation and isotopic analyses were applied to both mine-waste piles and naturally occurring alteration zones at nine mine sites. A case study from one site comparing the sulfur isotopic composition of minerals in an alteration zone and dissolved sulfate in proximal streams is presented. This case study shows the application of our data to differentiating sources of sulfate in the surrounding environment.

Jan 1, 2003

By J C. Diaz, C R. Scherpenisse

Blasting represents one of the most relevant unit operations in the process of mineral extraction. The final objective of this operation is that of obtaining an adequate final fragment size distribution such that the combined costs of drilling, blasting, excavation and transport, and crushing/grinding, are minimised, while at the same time producing the minimum possible level of damage to the surrounding rock mass. The strong influence that drilling and blasting has over the subsequent processes involved in the operational cycle makes it imminently desirable to have access to experience and technology which make possible the evaluation and optimisation of this unit operation. The correct use of vibration monitoring techniques offers a number of benefits in terms of their ability to examine any blasting process in detail. In effect, the measurement of particle velocity levels that result from the detonation of each explosive charge offers a means by which it is possible to measure relative efficiency of each charge, interactions (productive and counterproductive) between adjacent charges, and a definitive indication of general performance of any given blast design and its implementation. In this way the monitoring of blast vibrations in rock due to the blast event, can be used as a diagnostic tool, given that the correct interpretation of the vibration traces allows the determination of the level of interaction between the design and operational variables of the blast event. This makes it possible to evaluate, for example, the presence of out of sequence detonations, statistical scatter in the detonation times of pyrotechnic delay detonators, deficient detonation of charges, instantaneous detonation of charges and sympathetic detonation of charges, as well as the general of vibration levels in terms of peak particle velocity, acceleration, and displacement. Another important use of such data is in the construction of a database relating vibration levels to charge weight, hole diameter, and distance, for any given rock type, enables the calibration of predictive vibration models which in turn make it possible to predict the damaging effects of blasting. Knowledge of both the vibration levels induced, combined with quantitative measures of the geomechanical competence of a rock mass make it possible to estimate the probability of producing blast induced damage. The high levels of vibration generated by some blast events may damage the rock mass, producing new fractures or extending and dilating existing fractures. The vibration in this context may be considered as a dynamic stress provoking strain in the rock mass. This paper describes the application of the vibration monitoring technique, particularly in the underground mining environment, and its importance in diagnosis, modelling, control, and optimisation of the development blasting process. The potential of the technique is assessed in the context of achieving substantial techno-economic improvements development blasting results, increasing output whilst minimising the operational costs of the mining process.

Jan 1, 1999

By P J. Colbert, P D. Munro

OZ Minerals' Prominent Hill copper-gold concentrator in South Australia was built in 2008 with commercial production commencing in early 2009. In addition to recovery of valuable minerals, the flow sheet for this iron oxide-hosted copper-gold deposit has to address the issue of producing a good quality saleable copper concentrate by high selectivity against non-sulfide gangue. Detailed mineralogical studies integrated with the metallurgical test work highlighted that liberation of fluorine-bearing minerals and subsequent very efficient rejection in cleaner flotation was necessary to produce a commercial quality copper-gold concentrate. Bench scale laboratory metallurgical tests and mineralogical studies identified the need to regrind rougher concentrate to a P80 of 20 -25 microns or finer for adequate liberation of the fluorine-bearing minerals. Satisfactory separation of the fluorine-rich gangue material from the valuable copper sulfides requires highly efficient cleaner flotation. This is done by a combination of washed froth cleaning and conventional dilution cleaning. Proven equipment developed to meet similar taxing liberation and separation duties for the treatment of the refractory zinc-lead-silver ores of the Carpentaria-Mount Isa Mineral Province have been selected. The combination of Xstrata Technology's IsaMillÖ and Jameson Cell technologies addressed both the liberation and separation issues in the Prominent Hill concentrator. The energy efficient IsaMillÖ technology both regrinds the rougher concentrate while its inert grinding environment prevents contamination of mineral surfaces with 'debris' ensuring subsequent optimum flotation performance. Heading up the cleaner circuit with a 'scalping' Jameson Cell followed by conventional flotation equipment allows this section to take advantage of the Jameson Cell's high intensity flotation environment and froth washing capability to achieve maximum concentrate grade (at minimum fluorine levels) while maximising recovery through the use of conventional flotation machines. This paper looks at the development of the Prominent Hill flow sheet from the initial mineralogical and laboratory test work to the design, scale-up and early operation of the Prominent Hill regrind and cleaner flotation circuits. The mineralogically-based approach of domaining metallurgical ore types combined with the axiom of size-by-size mineral particle behaviour by liberation class gave a clear understanding of the liberation and separation issues involved in the processing of Prominent Hill ore. Technologies developed to meet much more onerous liberation and separation duties for the treatment of the refractory zinc-lead-silver ores of the Carpentaria-Mount Isa Mineral Province were successfully used to improve concentrate quality by rejecting non-sulfide gangue containing impurities. An IsaMillÖ and a Jameson Cell are included in the circuit for fine grinding and for additional concentrate cleaning. Plant performance since commissioning has justified the approach for metallurgical test work and equipment choices for the flotation circuit.

Jan 1, 2009

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

Mining companies often view water quality as an environmental issue. The importance of water quality as a production related issue in mineral beneficiation is greatly underestimated at many mineral processing operations. While most mine sites have comprehensive water balance data for water quantity, the information regarding the quality of water supplies available on site is limited, inadequate or non-existent. The seasonal variations in process water quality and changes in the composition of various water streams are not known. Despite the fact that water represents about 80 to 90 per cent of the volume of mineral pulp processed in a flotation plant, the influence of process water composition on flotation performance is often poorly understood. The process water used at mineral processing operations is made up from a number of available water sources, which can be classified as recycled water streams or make-up waters. The recycled water streams are commonly the tailings and concentrate thickener overflows, filtrate from the concentrate filtration plant and tailings dam return water. Make-up waters can originate from a variety of sources: surface waters (rivers, lakes, reservoirs, dams), groundwater (wells and springs), mains water (potable water), treated and untreated sewage waters and industrial effluents. Mineral processing plants are increasingly recycling water to reduce demand for fresh water and minimise the discharge of wastewater to the environment. However, increasing water recycling can have adverse effects on process water quality and ultimately on the performance of mineral separation processes. The main reasons for reduced plant performance due to water recycling are the accumulation of organic and inorganic compounds in the process water and increased microbiological activities. Other detrimental effects of water recycling can be increased reagent consumption and inefficient dewatering of tailings and concentrates. Recycling of water also tends to accumulate very fine suspended particles. Excessive amounts of slimes in the process water can also have an adverse effect on mineral beneficiation processes. The main constituents of process water are dissolved gases (oxygen, nitrogen, carbon dioxide), colloidal and suspended solids of inorganic and organic nature (including micro-organisms: dead or alive), dissolved organics (natural organic matter, residual reagents, reaction and decomposition by-products of chemical reagents, impurities in the reagents and metabolites originating from microbiological activities) and inorganic compounds (acids, alkalis, inorganic salts, metal ions, anions and heavy metals). Inputs to the chemical composition of process waters are: dissolution of soluble mineral phases present in the ore, surface oxidation followed by dissolution of mineral particles during grinding and mineral processing, the chemical composition of various make-up waters and recycled water streams, and reagent additions during mineral processing. The beneficial or detrimental impact of process water quality on flotation performance can be attributed to a number of subprocesses: adsorption and/or precipitation of inorganic and organic species present in the process water onto the surface of mineral particles, chemical reactions between process water constituents and the chemical species present on the surface of mineral particles and interactions between the chemical and microbiological species present in the process water and the various reagent species added in solution during mineral processing. Dissolved chemical species such as calcium, magnesium, iron, copper, lead, zinc, nickel, sulfates, phosphates and carbonates can have a strong effect on the electrokinetic properties of oxide and sulfide minerals, at certain pH ranges. Several reactions can occur at the solid-liquid interface that can play an important role in determining surface adsorption of reagents. Solid-liquid interfacial properties of mineral particles can be significantly affected by the conformation of adsorbed and precipitated reagent layers, which in turn are determined by solution chemistry. The chemical and microbiological constituents of process water can have a significant effect on liquid-gas interfacial properties and have a strong influence on froth height, strength and stability during flotation. Water chemistry can play an important role in determining the interactions between minerals present in the ore and the chemical reagents added in the mineral processing plant by altering the reagent-solution and mineral-solution equilibria. These interactions can include dissolution, micellisation and precipitation of reagents, dissolution of minerals contained in the ore followed by hydrolysis, complexation, adsorption and precipitation of dissolved chemical species and reactions between dissolved ions and various reagent species present in solution. All of the above mentioned subprocesses can ultimately have a significant effect on the efficiency of mineral processing operations. In this presentation, a systematic approach for assessing the composition of water supplies available at the mine sites and for investigating the influence of process water quality on the efficiency of mineral processing operations will be discussed. The consequences of mixing different quality water streams to produce the required volumes of process water for some flotation plants will be highlighted. To substantiate the water quality issues described in this paper some examples are given from a metalliferous processing perspective. However, the topics described in the paper are not only relevant to metalliferous processing but to all other type of mineral processing operations as well. In fact the principles described in this paper have also been successfully applied to the coal flotation industry.

Jan 1, 2006

By T

THE Sulphide Corporation's works for the smelting of ores containing lead, gold, and silver are situated close to the Cockle Creek railway station, on the main Northern railway line, and are about 95 miles from Sydney and 10 miles from Newcastle. A branch line runs to the works, and siding accommodation and bins are provided for expeditiously handling all ores sent for treatment. The Corporation also possesses wharfage facilities at the port of Newcastle, where consignments of ores arriving by sea can be handled direct into railway trucks for conveyance to the works.The greater portion of the ore treated at Cockle Creek comes from the Corporation's mine at Broken Hill, but a large quantity of other grades is also purchased and treated.

Jan 1, 1918

By P N. Nkrumah, A van der Ent, G Echevarria, P D. Erskine

Nickel phytomining is a low cost alternative to traditional nickel mining and a complementary process to existing mining operations in areas with low-grade nickel soils or nickel waste material. The process of nickel phytomining consists of growing selected hyperaccumulator plant species (‘metal crops’) on Ni-rich (ultramafic) soils, followed by harvesting and incineration of the biomass to produce a ‘bio-ore’ from which Ni salts or Ni metal may be recovered (Chaney et al, 2007). The ‘metal crops’ are selected on the basis of high biomass yield combined with high Ni concentrations (>1 per cent) in the above-ground biomass (Chaney et al, 2007). Currently, Alyssum murale and A. corsicum have been used for Ni phytomining trials, mainly undertaken in Albania and USA (Bani et al, 2015; Li et al, 2003), while the agronomy of <10 species has been tested in temperate regions (Nkrumah et al, 2016). Nickel phytomining has high economic potential; however, large-scale demonstrations are needed to provide ‘real-life’ evidence for commercial operations (van der Ent et al, 2015). Unrealised opportunities exist in tropical regions for commercial scale Ni phytomining. To date, the agronomy of tropical ‘metal crops’ has not been tested. This extended abstract presents the progress of tropical phytomining, and reports on agronomic trials undertaken to determine whether the trends in temperate regions could be confirmed in a wet tropical environment.CITATION:Nkrumah, P N, Erskine, P D, Echevarria, G and van der Ent, A, 2016. Progress in tropical nickel phytomining, in Proceedings Life-of-Mine 2016 Conference, pp 135–137 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J Johansson, E Lund, J Lööw, A Pekkari

Technological development is accelerating in the mining industry (Abrahamsson and Johansson, 2021) and in large parts of the world there is an increased environmental awareness (United Nations, 2015). This can mean both challenges and opportunities. The mining industry has long been criticized for its adverse environmental effects. However, there is now a lively discourse about the role of mining in facilitating the green transition towards sustainable development. Mining is increasingly recognised as a prerequisite for the green transition, by supplying key raw materials to enable, for example, digitisation and batteries for electric vehicles. The green transition not only amplifies the demand for metals and minerals but also intensifies pressure on the mining sector to assume greater responsibility for environmental and societal welfare (Dehaine et al, 2020). New technology, such as digitisation, automation, and remote control, play a crucial role in advancing towards more sustainable mining practices. Despite the expanding role of advanced technology, human involvement will remain important in the extraction process (Rogers et al, 2019), but new technology will change how miners do their work, which in turn will lead to changed competence requirements for miners (Herbert and Hidalgo, 2021) and increased need for further education. Given the significant shift towards sustainable mining, it is important to study how these changes may affect the work, competences, further education and skills of miners as human expertise will continue to be critical in the extraction process. Consequently, there is a need for proactive research to prepare for the inevitable changes and implement measures to support miners through this changeable period to ensure a smooth transition that protects miners’ safety and working environment. This extended abstract explores how new technology will affect the need for further education of miners in the future.

Sep 1, 2024

By S L. Simpson, J Waworuntu, B M. Angel

"The Batu Hijau copper/gold mine, operated by PT Newmont Nusa Tenggara, is located in the south-western part of Sumbawa Island, Indonesia, and is situated ~10 km from the south coast at an altitude of ~450 m above sea level. The mine became fully operational by year 2000 and processes approximately 120 000 t of ore per day that contain an average of 0.53 per cent copper and 0.4 per tonne (g/t) gold. Tailings management at the mine includes a deep-sea tailings placement (DSTP) system that discharges tailings through a pipeline via an outfall located at a depth of 125 m at the head of the submarine Senunu Canyon (Figure 1).The environmental impact assessment undertaken prior to approval of the DSTP evaluated both on-land tailings storage facility (TSF) and DSTP options for tailings management. Negative attributes of the on-land TSF included removal of approximately 2300 ha of forest/agricultural land, the potential relocation of >2000 people from their communities, the high average annual rainfall (>2500 mm) and potential for earthquakes presenting challenges for water management and creating a long-term risk of failure. The final choice and Indonesian Government’s approval of DSTP was also influenced by the close proximity of the deep submarine canyon to the mine. The Batu Hijau mine is one of the larger examples of DSTP in the world and deposits tailings at the greatest depth. The depth of the main canyon increases to >2000 m within 20 km of the coast, and to >3000 m approximately 50 km from the coast.The DTSP at Batu Hijau must comply with an environment management plan (EMP) and environment monitoring plan of permit stipulation that approved its commencement in 2000; updated in 2010 and 2015. The environmental management objectives were to avoid impacts to highly productive components of the ecosystem such as coral reefs, mangroves, surface waters and fisheries, and confinement of impacts to areas of low biological productivity. In the vicinity of the DSTP outfall and within the Senunu Canyon, the management plan predicted significant adverse impacts from the DSTP on the marine ecosystem in the form of: reduction in sea water quality due to elevated turbidity and dissolved copper concentrations burial of benthic organisms a reduced habitat for demersal fish.Recovery of the pelagic and benthic ecosystem to preoperating conditions was predicted to occur within the first two years after operations cease. The CSIRO has performed due diligence studies to independently verify compliance with permits and evaluate new monitoring objectives (Apte et al, 2004; Simpson et al, 2010; Angel et al, 2015), and has performed assessments of environmental monitoring data on the tailings footprint and ore stockpile processing against the above environmental objectives (Simpson and Angel, 2015).CITATION:Angel, B M, Simpson, S L and Waworuntu, J, 2016. Long-term monitoring and targeted assessments to improve management of mine wastes – the Batu Hijau project, in Proceedings Life-of-Mine 2016 Conference, pp 81–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By Y Tang, G Si

The analysis of rock fragment sizes plays a pivotal role in various stages of geotechnical and mining engineering. Traditional case-based methods often falter in addressing the variability in rock fragment images due to fluctuating geological conditions and imaging environments. To counter this challenge, AI-based models necessitate training on expansive and diverse data sets, encompassing a wide range of conditions and fragment types. However, the creation of such data sets is often hampered by financial and environmental constraints. This paper introduces a novel approach for rock fragment recognition, which leverages the power of AI for data augmentation, automated annotation and prediction. The methodology integrates three key components: Style-Based Generator Architecture for Generative Adversarial Networks (StyleGAN) for data augmentation, the Segment Anything Model (SAM) for automated annotation, and the multiscale version of you only look once (YOLO-MS) real-time instance segmentation model. The proposed method begins by training a new StyleGAN model using the original data set. It then delves into exploring the latent vectors of different rock fragment images to generate specific ‘style representations’. These latent vectors form the foundational elements of each image in a high-dimensional space, encapsulating critical features such as size, shape, texture, and colour variations. The next step involves conducting quality checks on the generated images to ensure their realism and suitability as training data. Subsequently, the augmented image set is annotated using modified SAM module, followed by training the YOLO-MS real-time instance segmentation model. The performance of this model, trained on the augmented data set, is compared with a model trained on the original data set, particularly in terms of generalisation abilities in new scenarios. The results exhibit a significant enhancement in accuracy, robustness, and generalisability of the model trained on the augmented data set, underscoring the potential of StyleGAN as a powerful tool for data augmentation in geotechnical engineering image analysis.

Sep 1, 2024