Search Documents

By A. E. M. Warner, I. E. Hills, C. L. Harris

Since the late Dr. Keith Brimacombe, et al, performed tests at the now-closed Asarco Tacoma smelter and the Inco Copper Cliff Smelter on Peirce-Smith copper converters almost thirty years ago, many Pyro-metallurgists have investigated using the technology. To the best of the authors knowledge, except for shrouded tuyere technologies using substantial oxygen enrichments, the core idea of using high pressure air injection has not been implemented anywhere in the world. This paper reviews the fundamentals of this technology and summarizes the basic economic considerations. It also presents the circumstances of where and when high-pressure injection might be justified.

Jan 1, 2007

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young&apos;s modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By F. Guo

"The leaching kinetics of zinc sulphide concentrate was studied under total pressures ranging from 0.3 MPa to 0.5 MPa and leaching temperatures ranging from 358 K to 378 K. The apparent activation energy of leaching reaction under different total pressures was calculated. The results show that for the extraction of zinc at low-temperature pressure leaching is controlled by an interfacial chemical reaction. This was supported mineralogical analysis of the leaching residue. The kinetic equation for low-temperature pressure leaching of zinc sulphide concentrate was further established by quadratic regression on the basis of shrinking core model.INTRODUCTIONThe Roast-Leach-Electrowinning Process (RLE) is the primary route for zinc production and responsible for more than 85% of the total zinc production (Souza et al., 2007). During the roasting of zinc concentrates, fugitive SO2 causes pollution. The prevention of SO2 emissions from the RLE process can be one of the challenges to this technology (Deller, 2005). In the 1980s, the Zinc Pressure Leach (ZPL) process changed the concept of zinc hydrometallurgy, in which zinc sulphide concentrate is directly leached at approximately 423 K and approximately 0.7 MPa oxygen overpressure and the sulphidic sulphur is oxidized into elemental sulphur so that the pollution by SO2 is completely avoided. Since 1981, five zinc plants have adopted the ZPL process either for expansion by integration with existing roasting facilities, or for the production of zinc without any roasting at all (Collins et al. 1994; Barth et al. 1998). The innovation of the ZPL process has made the zinc industries more competitive although it needs an autoclave. The direct leaching technology of zinc is still in development."

Jan 1, 2012

By John N. Ludden, Maurice Rive, Hillar Pintson

"Quelques soixante-dix-sept plutons présents dans la Sous-Province de Pontiac et dans la partie centrale de la Sous-Province de I’Abitibi ont fait I ’objet d’une reconnaissance systématique. Ils ont été regroupes en huit suites plutoniques majeures et trois suites mineures à partir de critères géologiques et petro logiques. Parmi les suites majeures, quatre représentent I' activité intrusive la plus ancienne dans la région. L’une d' entre e/les est représentée par deux complexes anorthosito-gabbroi' ques lites et les trois autres comprennent les orthogneiss dioritiques a leucotonalitiques et les intrusions dons la composition varie de diurétique et granodioritique à leucotonalitique. Leur mise en place peut être pretectonique a syn ou tarditectonique; certains plutons sont synvolcaniques. Quelques data/ions U! Pb effectuées à propos de ces roches donnent des âges s' étalant entre 2 718 et 2 694 MA. Les données géochimiques indiquent la présence des deux lignées magmatiques, tholemique et calcoalcaline bien qu’il n'y ait aucune évidence de relations entre elles dans I' espace et dans le temps. Ces suites magmatiques différentes peuvent provenir soit d’une croute tholemique impliquée dans un processus de subduction soit directement du manteau.Les trois autres suites majeures comprenant des monzodiorites, des granodiorites et des monzonites ainsi que les deux suites mineures comprenant des syenites correspondent à un évènement intrusif plus jeunesse déroulant entre2 694 et2 680 MA. Ces roches sont syn, tarti a post tectoniques et sont enrichies en alcalins, Ba, Sr et terres rares legeres par rapport aux quatre suites précédentes. Leurs caractères chimiques prop res suggèrent qu' e/les proviennent d' une source différente par rapport à celle precedemment citee.La derniere suite plutonique majeure correspond a un monzogranite leucocrate, riche en pegmatite, également syn a tard tectonique, dont I' age n' est pas connu avec précision. ll représente le seul granite ""vrai"" de la région et dérive d’une anatexie soit des meta sédiments soit des granodiorites-tonalites plus anciennes. La troisième suite plutonique mineure correspond a quatre stocks de granodiorite porphyrique qui n’ont pas été étudiés en détail.ABSTRACTSevenly-sevenplutons have been identified in the east-centra/part of the Abitibi Subprovince and adjacent Pontiac Subprovince. These have been subdivided, on the basis of geological and petrological criteria, into eight major and three minor plutonic suite. Four of the major suite, which represent the oldest intrusive activity in the area, range in composition from dioritic-leucotonalitic orthogneisses to diorite-granodiorite/leucotonalite and include two layered anorthosite- gabbro complexes. Their time of emplacement ranges from pretectonic to syn-late-tectonic and some plutons are synvolcanic. U-Pb zircon ages for these rocks range from 2 718 to 2 694 Ma. Geochemical data indicate the presence of both calc-alkaline and tholeiitic magma series for these rocks although there is no evidence time and space relationships between the two. The different magma series also suggest the derivation of these rocks from two sources, either from subduced tholeiitic crust or directly from the mantle. Three major monzodiorite-granodiorite, monzonite, and two minor syenite suites comprise a younger inlrusive event ranging from 2 694 to 2 680 Ma in age. These rocks are syn-, late- to post-tectonica and, compared to the above four plutonic suites, are enriched in alkalis, Ba, Sr and light Rare Earth Elements.Their distinctive geochemistry suggests that these rocks were derived from a different source region than for the older plutonic suites. The remaining major plutonic suite consists of leucocratic, pegmatite-rich, monzogranite-granodiorite. These rocks are also syn- to late-tectonic but their ages are not known with precision. They are the only ""true"" granites in the area and were derived by the partial melting of either older"

Jan 1, 1990

By Yvon T. Maurice

Under the auspices of the Federal-Provincial Uranium Reconnaissance Program, a geochemical orientation survey was undertaken in an area of uraniferous Lower Proterozoic (Aphebian) rocks near Cape Dorset in southwest Baffin Island. The main objective of this study was to establish a methodology for a future reconnaissance geochemical program using lake samples over a 300-mile Lower Proterozoic rock belt that occurs along the southern coast of Baffin Island. Mineralogical and chemical studies of known radioactive occurrences, combined with detailed sampling of secondary environment media in the vicinity of the showings. indicate that uranium is the most significant pathfinder, despite considerable enrichment of other metals in the uraniferous rocks, Significant geochemical patterns produced by uranium in lake waters and uranium in lake sediments have been obtained, but their relative usefulness depends on the distribution of carbonate bedrock, which in turn affect the bicarbonate content of lake waters. In southern Baffin Island, because of erratic variation in lake-water alkalinity, it is recommended that both water s and sediments be sampled on a routine basis. The need for lake-water acidification to prevent depletion of soluble metal ions in samples resulting from adsorption on the walls of the containers and/or suspended solid matter is discussed briefly. The base metal potential of the area was examined in some detail and found to be significant, particularly for a Lower Proterozoic gossanous formation that occurs throughout southern Baffin Island.

Jan 1, 1977

By W. C. Whittaker

"This paper gives a brief resume of the changes in the market picture for Western coal since 1948. It then analyzes present markets and recent developments in Western Canada, the western United States and Japan, and forecasts future markets in these areas to 1975.INTRODUCTIONCOAL HAS BEEN MUCH IN THE NEWS OF LATE, both in the United States and in Canada. In the United States, this is because of the booming condition of the industry and because of the purchase of control of a number of America's largest coal producers by the integrated oil and metal producing companies seeking additional fossil fuel reserves and diversification. In this regard, it is interesting to note that ownership of America's largest strip coal producer was recently acquired by one of the world's largest copper mining companies. In Canada, the conclusion of several large-scale, long-term contracts for the sale of coal to the Japan Steel Group and the projected use of Canadian coal in steel mills in the western United States has focused much attention on the coal industry."

Jan 1, 1968

By M. C. Makepeace

"It is the objective of designed experiments to obtain more information for less material and process cost than can be obtained by traditional experimentation. In this paper, the fundamental concepts on which the statistical design of experiments is based are briefly re-viewed according to the following outline: The Experiment The Design The Analysis Two simple 2"" factorial experiments are presented as examples."

Jan 1, 1967

By Elmer Palmer

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large ?state of the art? concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By J. O. G. Sanderson

Introduction In this paper it is proposed to review the history of petroleum geology in western Canada, to discuss some of the main events which have affected its progress, to mention its relationship to the petroleum industry, and, finally, to appraise its present status and possible future importance. It will be useful first to consider the meanings of the terms petroleum geology, petroleum geologist, and the petroleum geology of a terrain. Petroleum Geology. - In simplest terms, geology is the science of the earth. Hence petroleum geology is the science of that portion of the earth that encloses pools of petroleum. The systematic delineation and study of stratigraphic geology began about 1820. The systematic development and study of petroleum geology started about 1910. It is a relatively immature branch of geology. Petroleum Geologist. - This term may be applied to a fully qualified geologist who is engaged for a time, be it a job, a contract, or a lifetime, in the work of finding and developing deposits of petroleum and related substances. No man may properly be called a petroleum geologist who is not first a fully qualified geologist.

Jan 1, 1946

By L. R. Wilkinson, W. J. Howarth, G. J. Wenk

Over a period of three years, a cooperative program in Australia has resulted in the development of radioisotope immersion probes for the on-stream analysis of mineral slurries. Two basic probe types are now available on a commercial basis - fluorescence and absorption probes - and within each type there are a number of variations so that optimum sensitivities can be obtained for elements with atomic number greater than titanium (22), thus covering most metals of interest to modern metallurgy.

Jan 1, 1973

By Mathieu Dubé

Good mechanical strength of green iron ore pellets is required to avoid breakage and excessive deformation during their handling and further processing. However, green balls with good resistance to handling are often too plastic, which impacts the bed permeability in induration furnaces. Measurements of plasticity, bed void fraction and green ball sphericity as well as bed permeability were carried out on various samples of green iron ore pellets having different mechanical strength. Results show that bed void fraction, sphericity and permeability all depend, to some extent, upon green ball mechanical strength (plasticity). Understanding and controlling the mechanical strength of green iron ore pellets would then help to maximize both the productivity of the induration process as well as the quality of fired pellets through a more stable firing process. Results of research work carried out at COREM, with the objective of improving green ball characterization methods, are presented in this paper.

May 1, 2007

By A. Danaei, A. McLean, M. Barati, C. Ravindran

"The aluminum industry generates about 90 million tonnes of red mud each year. Previous research shows it could be utilized as a refining flux with a high capacity to absorb phosphorus and sulphur from hot metal in the steel industry. The present study was undertaken to evaluate the melting properties of such fluxes, as it affects the effectiveness of the flux. The results show that the melting behavior of red mud is strongly affected by lime addition and the characteristic melting/softening temperatures reach minimum VALUES (at 32.7 wt% CaO. From these findings, a correlation was established between melting behavior and optical basicity. This allows one to adjust the composition of the flux based on the process requirements. INTRODUCTIONThe aluminum industry generates about 90 million tonnes of bauxite residues each year. This residue is usually red in color because it contains a substantial amount of iron oxide. The red mud, as it is called, is a solid waste with a high concentration of sodium oxide, high pH (10 to 13), and high alkalinity, and thus is harmful to many forms of life. Traditionally, the material is stored in large tailings ponds within the plant’s vicinity (Power, Grafe, & Klauber, 2009). Development of solutions for safe disposal or preferably using this residue for other industrial processes or applications could help restore polluted locations and eliminate a negative impact on the environment (Haake, 1988; Power et al., 2009; Yan & Xuegong, 2010).The mineralogy and chemical composition of red mud depends on the quality of the bauxite and refining process parameters. In general, it consists of iron oxide (Fe2O3), aluminum oxide (Al2O3), titanium oxide (TiO2), sodium oxide (Na2O), silicon oxide (SiO2), and calcium oxide (CaO) (Power et al., 2009). Like most ores and soils, bauxite can contain trace quantities of metals such as arsenic, beryllium, cadmium, chromium, lead, manganese, mercury, nickel, and naturally-occurring radioactive materials, such as thorium and uranium. Most of these trace elements stay in the residue (Power et al., 2009)."

Jan 1, 2012

By R. Lasmanis

"Washington State&apos;s diverse geological setting is reflected by its several types of porphyry Cu-Mo deposits. All are associated with calc-alkaline intrusions, and they range in age from Jurassic to Miocene.The largest is the Mount Tolman Mo-Cu deposit located in the Omineca Belt. It contains 2.18 billion tonnes of material averaging 0.093% MoS2 and 0.09% Cu. There are intermediate-size Mesozoic deposits in the Intermontane Belt. The Cascade volcanic arc hosts small- to medium-Tertiary deposits. Among these, of particular interest is the Sunrise breccia pipe, which has been explored over a vertical distance of 1000 m. It contains reserves of 64.6 million tonnes averaging 0.319% Cu and 0.071% MoS2 with significant tungsten values. The Glacier Peak deposits have potential resources of 1.7 billion tonnes averaging 0.334% Cu and more than 0.015% MoS2 and also contain tungsten. The Margaret deposit can be classified as a porphyry Cu-Au type; it has reserves of 200 million tonnes averaging 0.434% Cu, 0.0175% MoS2> 0.27 g!t Au and 1.92 g!t Ag. Drill intercepts of the North Fork deposit also show significant gold values.Mineralization and hydrothermal alteration of these deposits are typical of porphyry deposits, although some differences can be noted. The Mount Tolman molybdenum deposit contains topaz alteration zones and is transitional between a plutonic type and a Climax-type molybdenum system. Other deposits, such as the Kelsey, Mazama, North Fork, and Margaret, are low-sulphide systems that contain significant amounts of magnetite."

Jan 1, 1995

By E. R. Hughes

Introduction Situated 182 miles east of Vancouver, on the Kettle Valley branch of the Canadian Pacific railway, the Princeton coal field is readily accessible to the Coast markets. The area covers approximately forty square miles and present indications are that the deposits should contain at least 300,000,000 tons of coal. Comparatively little development has yet taken place in this coal field. Since the commencement of recorded output, the collieries operating in this area have produced 1,640,518 tons of coal. The coal field proper includes only the Tertiary deposits adjacent to the town of Princeton and does not include the Coalmont or Nicola deposits. Production has never been on a large scale. The largest annual output from any property was 81, 780 long tons mined at the Granby colliery in 1940. Coal output was first recorded in 1909 and since that time fifteen properties are reported to have either mined coal or to have done prospecting or development work; of these, only two are presently active. However, none of the properties now inactive were closed because their coal resources were exhausted. The accompanying key map shows the extent of the Princeton coal field, and the location of the coal mines and prospects in this field General Geology The Princeton field is underlain by rocks of Oligocene age and is one of the series of more or less isolated Tertiary lake basins in which coal, or lignite, has been found in the interior of British Columbia. Resting on the Nicola group rocks of Triassic age, the Princeton sedimentaries consist of sandstones, conglomerates, shales, bentonite, bentonitic clays, and several seams of coal. Tertiary volcanics occur both above and below the stratified rocks and in places they have been thrust through the overlying measures. In some areas, the coal has been burned to a red ash as the result of vulcanism, while in other parts some of the moisture has been driven from the coal, thus improving the grade. The field can best be described by dividing it into two areas: the Southern area, lying to the south of the town of Princeton, where most of the mining has been done; and the Northern area, to the north of Princeton, where very little development has taken place.

Jan 1, 1947

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By L. E. Djingheuzian

Introduction For many years the immense deposits of bituminous sands of northern Alberta have been attracting the attention of our governments, engineers and .scientists ( 6). Undoubtedly these bituminous sands represent one of the greatest potential resources of liquid fuels in the world. However, their commercial development has been retarded by the complexities of the technological problem and by the economic factors involved in the processing of the sands. The technological problem has been attacked from several angles ( 2, 3, 1, 11), and cold water separation of bitumen is one of them. To the ore dressing engineer, the cold water process is of utmost importance since, by the use of standard ore dressing machinery, it accomplishes most efficiently and economically the separation of bitumen from bituminous sands. The significance of using ore dressing equipment was especially enhanced by the fact that the scientific principles which underlie the design of standard machines were demonstrated in the cold water separation process with an extraordinary clarity. This greatly facilitated the analysing of limitations and advantages of different machines during-the pilot plant investigations and helped to complete the investigations practically in the allotted time.

Jan 1, 1952

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By C. Han, S. J. Zhou, Y. B. Shen, D. Z. Wei, P. Fang

"Collecting property of two hydroxamic acid collectors have different type of nonpolar structure to hemimorphite has been comparatively studied via monomineral flotation test, and the reason causes different collecting performance has been discussed from the view of relationship between molecular structure and collecting property. The flotation tests results show that C5-9 hydroxamic acid has an unbranched linear alkyl nonpolar group shows better collecting property to hemimorphite than cyclohexyl hydroxamic acid which has a naphthenic nonpolar group. FTIR detecting results show that the adsorption type of collector adsorbed on hemimorphite surface is chemical adsorption. Calculation results of polar group’s geometric structure parameters, polar group’s electron density distribution, octanol-water partition coefficient (logP) and molecular frontier orbital energy show that the key factor caused different collecting property of two collectors to hemimorphite is the logP; unbranched linear alkyl nonpolar group is more conducive than naphthenic nonpolar group to make hemimorphite particle more hydrophobic.INTRODUCTIONZinc-bearing mineral recovered from lead-zinc ores is the main source that people can obtain zinc resource from nature. However, natural sulfide ores are currently getting depleted steadily for the primary zinc source. In order to satisfy the future demand of zinc resource, there is an obvious recognition that the recovery of zinc oxidized minerals from the ores is a crucial alternative (Hosseini & Forssberg, 2007; Navidi Kashani & Rashchi, 2008).But the fact that can’t be ignored is the flotation of zinc oxidized minerals is much more difficult than that of zinc sulfide minerals, which is mainly due to the flotation characteristics of these zinc oxidized minerals such as lower selectivity and higher reagent consumption, as well as complex and variety of lead-zinc ores. Presently, there have been many various beneficiation technologies used for recovering zinc oxidized minerals and dealing with ores for recovering metallic zinc such as flotation and hydrometallurgy (Abkhoshk, Jorjani, Al-Harahsheh, Rashchi, & Naazeri, 2014; Önal et al., 2005). But from an overall perspective, flotation is the most common method used for the beneficiation of zinc oxidized minerals, and there have been extensive investigations conducted on the flotation of zinc oxide ores (Ejtemaei, Gharabaghi, & Irannajad, 2014). Until now, the most well-known method used commercially for the flotation of zinc oxidized minerals is sulfidization with sodium sulfide and flotation with a cationic collector of amines containing from 8 to 18 carbon atoms. However, a major problem for this method is the large amount of fines and slime results in the increase of reagent consumption and promotes the phenomenon of slime-coating. For preclude this negative effect, the de-sliming and processing optimization is indispensible (Peres, Borges, & Galery, 1994; Salum, de Araujo, & Peres, 1992)."

Jan 1, 2016

By Robert S. Penczak

Red Lake Gold Deposits ? Descriptive Classification (modified from Pirie, 1982) VHR Au -- Volcanic-hosted (vein & wall-rock) replacement Au deposits ~93% of camp production Q-(T) Au -- Quartz-(tourmaline) vein Au deposits ~7% of camp production Quartz-sulphide Au deposits Porphyry-hosted sulphide Au deposits Current & Significant Past Producers Camp Production 21.6 M oz / 672 tonnes Au Other Deposits / Occurrences (Intermittent Exploration

Apr 1, 2005