Search Documents

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010

By J. H. Nantel

Indications are that underground mining is gaining favour with large and small mining companies due to environmental and sustainability concerns. Dramatic changes to mine fill technologies will be needed in order to keep pace with these emerging trends. The industry will be compelled to gravitate toward zero discharge mining operations. Innovative handling of mine tailings will become a focal point in this effort. The challenges are to use a greater portion of the residues and to manufacture a fill with better properties. This is a tall order that can only be addressed through a systematic research and implementation process involving mining companies, universities, research organizations, manufacturers and governments. The mining industry has to be at the forefront of this technology push in mine fills for the future mines. It will also be called upon to lead the way in other research areas. The industry will have to partner with other technology providers: universities, government laboratories and consultants.

May 1, 2007

By J. J. Jonas, G. R. Stewart, N. Pokutylowicz, S. Yue, R. Varano, A. Elwazri

Differing thermal histories in and around a weld can lead to differences in grain size, phase composition and morphology of precipitates; mechanical properties will vary accordingly. Hardness testing gives limited information and the machining and testing of tensile and/or impact specimens that would reveal these variations (which may occur over very small distances) is not practical. Therefore, in this investigation, shear punch testing was applied to measure the variation in the room temperature mechanical properties of a welded pipeline steel.

Jan 1, 2005

By J. J. Ferreira, M. L. Thurston, I. L. Chinn, D. M. Rose

"Concerns about using microdiamonds for resource estimation have been raised by workers because multiple diamond populations exist in many parts of the mantle source region, small diamonds in kimberlite could be exposed to proportionately greater levels of resorption and modification, and euhedral microdiamonds could crystallize immediately prior to kimberlite eruption. This paper addresses these concerns; discusses the geology of the mantle, the principal diamond host rocks, and the impact of mantle processes; compares micro- and macrodiamond properties and features; and outlines steps to identify and mitigate the risk of diamond resorption and its impact on the diamond grade-size relationship.RÉSUMÉ Des travailleurs se sont interrogés sur l’utilisation de microdiamants pour estimer la ressource; en effet, de multiples populations de diamants existent dans plusieurs secteurs de la région source dans le manteau. Des petits diamants dans la kimberlite pourraient être exposés à des niveaux proportionnellement supérieurs de résorption et de modification; de plus, des diamants idiomorphes pourraient cristalliser immédiatement avant l’éruption de la kimberlite. Le présent article traite de ces questions, discute de la géologie du manteau, des principales roches-mères des diamants et de l’impact des processus dans le manteau, compare les propriétés et les caractéristiques des micro- et des macrodiamants et définit les étapes pour identifier et mitiger le risque de résorption des diamants et son impact sur la relation entre la taille et la qualité des diamants."

Jan 1, 2016

By H. Staton, XPS Consulting & Testwork Services, T. Deng, M. Kelvin

"Lundin Mining’s Eagle Operation, located in Marquette County, northern Michigan consists of a mine and concentrator that processes a Ni-Cu-(PGE) ore. Mine production began in 2014 and is expected to achieve production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year. The ore is trucked to the Humboldt Mill, where both a Ni and Cu concentrate is produced.XPS Consulting & Testwork Services (XPS) has assisted the team at Eagle since 2013. Prior to start up, the ore was piloted at the XPS lab in Sudbury, Ontario to demonstrate the concentrator flowsheet and establish flotation operating strategy. XPS consulting metallurgists worked closely with the Eagle team during the commissioning of the plant providing troubleshooting, sampling, metal balancing expertise and support. Finally, a series of monthly composites over a 6 month period was submitted for mineralogical characterization to assess plant performance, identify opportunities for improvement and to provide a baseline for the future operation.Lundin’s investment to test the ores ahead of mining and to team with XPS’s experienced mineral processing engineers to help commission the plant has led to the plant achieving concentrator production targets shortly after startup. The commitment to training and implementation of best practices, and a culture where ongoing testing is the norm, puts the Eagle Operation on sound footing for future operation.INTRODUCTIONLundin’s Eagle Mine is a subsidiary of Lundin Mining located in the upper peninsula of Michigan. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 2 hours to the Humboldt mill.The ore is an ultramafic hosted high grade Cu Ni deposit and exists as either massive or semi massive sulphides. The high resource grade of Cu (2.49%) and Ni (2.93%) make this a valuable ore source. (Owen & Meyer, 2013) A metallurgical team was put together by Lundin to ensure the mill was designed and commissioned to optimize metallurgy in the shortest time from this valuable deposit. The commissioning plan targeted commercial production by Q1 2015."

Jan 1, 2016

By Marc Symbaluk

Core Programs Current ? Aboriginal Involvement Program ? Adaptive Forest Management / Forest History Program ? Grizzly Bear Research Program ? Natural Disturbance Program ? Foothills Growth and Yield Association ? Foothills Stream Crossing Program ? Fish and Watershed Program ? Caribou Landscape Management Association ? Social Science Program ? Local Level Indicators Program ? Communications and Extension Program ? Geographic Information Systems Program ? Mountain Pine Beetle Ecology Program In Development ? Climate Change Program ? Forest Community Program ? Water, Quantity and Quality Program (Water for Life) ? Circumboreal Initiative ? Yellowhead Ecosystem Management Group

May 1, 2008

By Jason Berenyi

Presentation Overview ? What is Potash? ? Where are the potash deposits? ? Current potash mines ? production, capacity and planned upgrades ? Saskatchewan Saskatchewan?s Potash Production Potential s ? Current Status of Potash Exploration ? Increasing Demand for Potash ? Saskatchewan global role

May 1, 2009

By A. Ignatieff

"Excavation, the principal mining process, 'which hitherto has been based largely on the intuition and logic of mining men, is increasingly receiving the attention of engineers and scientists versed in rock mechanics. The paper intro-duce the principles of this science in simplified form, directed both to underground and open-pit mining. Reference is made to the large annual tonnage from ore and rock excavations, which in 1967 were responsible for 250 million tons of mineral production in Canada.The urge to transform excavation into a continuous instead of an interrupted process is discussed with references to the various types of energies employed or proposed in rock breakage or excavation. Due to the rapid decay of applied energy in the discontinuous and heterogeneous rock environment, large confined blasts proposed for in-situ mining do not give much expectation of success as yet. Raises and ventilating shafts are already bored in reasonably hard rock. Tunnelling machines will be used for drifting and cross-cutting in the future, but continuous mining machines of the cuttmg and shearing type are not 'around the corner' for stoping typical orebodies. On the other hand, bed mining, particularly of coal, has led the way in continuous mining, and Remotely Operated Long-wall Face (ROLF) experiments are progressing in an encouraging way. Some reflections on the mining environment in relation to the human element are made."

Jan 1, 1970

By G. Harper

"AbstractThe Suetut. Copper deposit, 230 miles northwest of Prince George, B.C., was discovered in August of 1971. Subsequent exploration has included 56,417 feet of surface diamond drilling in 139 holes. The deposit occur in gently dipping volcanic rocks of the Upper Triassic Takla Group, which out crops as rugged mountains.The general Mesozoic sequence comprises some 20,000 feet of green and red basaltic to andesitic rocks. The Lower Formation is characterized by subaqueous basalt, andesite and augite porphyry flows with interbedded breccias. They were rapidly deposited in tectonic depressions of limited extent and steep gradients. Facies changes are abundant. The Middle Formation. consists of volcaniclastic rocks made up of fragments from the underlying formation. Two cycles are discernible , both with basal turbiditic, tuffaceous sandstone and shale units overlain by massive, volcanic conglomerates exhibiting graded and cross bedding. A broader, shallower-water basin is indicated. The top of the uppermost unit was subaerially deposited. The Upper Formation is a variable sequence of volcanic sedimentary rocks. Detritus was supplied from a wide source area and included multiple reworked fragments of the lower formations and material from other rock groups known in the region. Zeolite facies metamorphism is recognized throughout: the entire sequence. Epidote is particularly abundant in the Middle Formation, demonstrating the results of metasomatism.The mineralized zone is approximately concordant with the strata over 100-200 feet of the Middle Formation succession . It lies just below the zone of transition from subaqueous to subaerial deposition in the top unit. Hematite, chalcocite, pyrite, bornite, chalcopyrite and native copper are disseminated throughout all sizes of lithic fragments and matrix. Concentration into the specific zone is believed to be due to upward leaching of copper during lowgrade metamorphic and metasomatic reaction. Precipitation occurred in the zone of hydration characterized by prehnite-pumpellyite below the oxidized subaerial rocks."

Jan 1, 1977

By M. J. Davie, D. S. Ross

"The successful design of a new mine water pumping system is in part dependent upon the accuracy with which the operating conditions can be forecast. This paper outlines the data which should be obtained on water quantity and quality. Methods of modifying the quality are also discussed. Some pumping systems for disposal of sludge are described, citing operating examples. The various types of mine dewatering pumps are described in terms of design characteristics as they affect operating efficiency and installation and maintenance costs. Piping system parameters are outlined. Finally, a hypothetical case study of pumping from a depth of 3,000 ft is assessed, with particular reference to capital costs.IntroductionMany mine operators would agree that the pumping system usually receives a low engineering priority during the design stage, and as a consequence causes some of the most frustrating problems during production. For a ""dry"" mine (up to 200 gpm), design of the pumping system may indeed be simple, but outside of the potash industry such mines are not common. For ""wet"" mines, the pumping system is important because it significantly affects the initial capital and on-going energy costs of the mine and, in the area of sludge disposal, the working conditions and production costs. Indeed, a failure in the pumping system usually has serious, and sometimes disastrous, consequences.The intent of this paper is to outline the factors which should be considered in the design of a pumping system and to describe the types of pumps used in mine dewatering and relate them to practical operating systems."

Jan 1, 1980

By A. L. Nunes, J. R. E. Garcia, G. Silva, U. Prasad, C. Rabe

"Drilling through the Guayabal shales, a gray calcareous shale, and the C1 to C100 formations, a well-cemented calcareous-sandstone in Corralillo field, Mexico, is a challenge due to severe wellbore instability problems. Additionally, there has been a history of ineffective reservoir stimulations by hydraulic fracturing. To predict and mitigate these subsurface issues, it is essential to characterize the mechanical properties and rocks strength for a better prediction of borehole stresses and collapse pressure during drilling. Various correlations can be used to estimate and/or determine the unconfined compressive strength but most of them are based on transit time and porosity.In this study, grain size distribution was combined with acoustic travel time, porosity and static Young’s modulus to develop a rock strength prediction model for the turbiditic sandstones of the Chicontepec basin. The main reason this combination of parameters was employed was because of the wide variations in rock strength estimated using traditional porosity-based correlations such as the McNally’s (1987), GMI-Jizba-E’s and Bradford’s (Bradford et al., 1987).To develop a new correlation, a geomechanical and microstructural campaign was initiated. Mineralogy by X-ray diffraction, pore and grain sizes by petrography, clay distribution by SEM and porosity by mercury intrusion porosimetry were measured. Static and dynamic Young’s moduli and Poisson’s ratios were acquired by triaxial and ultrasonic measurements on undisturbed sandstone samples from the Chicontepec basin. More than ten offset wells with wireline data, including transit time, porosity, density, resistivity and gamma ray, were used for reservoir and geomechanical characterizations.Our analyses lead us to propose a new correlation for predicting the uniaxial compressive strength (UCS) of sandstones of the Chicontepec Basin as a function of transit time and grain diameter, both of which can be derived independently from destructive laboratory tests. Our results also highlight the importance and value adding of a combined approach incorporating grain size analysis in the rock strength prediction. The UCS predicted using the transit-time and grain-size-based model presents a median value (P50) of 76 MPa, P10 of 55 MPa and P90 of 89 MPa."

Jan 1, 2015

By M. du Plessis, G. More O’Ferrall, A. Hartzenberg

"Lonmin Platinum has experienced several cases of large-scale hangingwall instabilities during the extraction of the Upper Group 2 Chromitite Layer (UG2) at a number of the Marikana operations along the Western Limb of the Bushveld Complex. These instabilities were all attributed to the presence and interaction of prominent geological features and highlighted that assumptions made in the design of the stable pillars and stable span were potentially overly simplistic in these areas. Investigations into the various case studies over the past ten years have resulted in the identification and classification of the rock mass characteristics of the geological structures causing the instabilities.In order to get a better understanding of these instabilities, it is important to understand the structural geology in general, and the sequence of events that led to the formation of the Bushveld Complex in particular. The tectonics involved in the formation of the various layers around the economic mineralized layers has been investigated, and the influence of these tectonic events on the stability of the UG2 stopes hypothesized.Following this investigation, the behaviour of the various layers in the hangingwall of the UG2 is better understood. This paper presents a description of the ground conditions being experienced in the underground stoping environment, the possible source of the associated structures and the resultant behavioural mechanism of these structures causing the rock mass instabilities."

Jan 1, 2015

By K B. Bowley

This paper covers the application of a systematic maintenance plan by the Plant Engineering Department of Rio Algom Mines Limited, Milliken Division. The plan established the function of work study, developed and installed formal work planning and labour cost control procedures, and extended the existing preventive maintenance routines. In June, 1961, assisted by management consultants, a more scientific approach to maintenance was instituted. The emphasis was placed on the control of labour. The development and application of the primary control system was established with-in six months. Since then, the Department has operated for a year, consolidating the system. The procedure of the installation, the results achieved and the results to be expected will be discussed. JNTRODUCTION THE Milliken Division of Rio Algom Mines Limited operates a 3,000-ton-per-day uranium mine, in the Elliot Lake district of Ontario, which went into production in April of 1958. The lowest operating level is 3,000 feet below surface. Mining is carried out by open stopping, with planned pillar support and footwall haulage on rail.

Jan 1, 1963

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By Karl J. C. Harries

"14.1. INTRODUCTION1The boilerplate of an agreement is not a single provision, but a series of provisions that are expected in “every agreement”. They are sometimes also referred to as the “lawyer’s provisions”. Many businessmen consider the boilerplate to be superfluous and, to some extent, window-dressing by the lawyers – even legalese. They will often offer advice to the effect that it can “pretty well be ignored”. Such advice could not be more wrong.Most boilerplate provisions are essential parts of every agreement. Some may be part of a “standard package” and may have little relevance to the agreement at hand, but these are the exception rather than the rule. The exceptions should not be treated as justification for giving all these provisions short shrift. The boilerplate should receive the same review, consideration, and negotiation as the provisions that set forth the business deal. It is often these provisions that make the deal work or that are turned to at the time of disputes. If they are inadequate, as they sometimes are (unfortunately, some draftsmen are also loath to review or update their standard boilerplate provisions or to tailor them to the deal at hand), they can create problems, rather than offer solutions. Such problems can be costly and time-consuming for the parties to address. Inadequate or incomplete provisions may ultimately be one of the reasons for the parties to turn to the courts to settle their differences. On the other hand, good boilerplate provisions can help keep them out of the courts.One of the principal objectives of an agreement should be to provide procedures, or mechanics, for implementing agreed principles and for the parties to follow to settle their differences, real or perceived, without going to the expense and disruption of a lawsuit. An agreement should aim to keep the parties away from the courts, not serve as a springboard to the courts. It must nevertheless be acknowledged that, if there is a major falling-out among the parties to an agreement, the chances are that, however carefully the provisions of that agreement have been negotiated and drafted, the parties will end up before the courts or some other adjudicating body."

Jan 1, 2003

By O. A. Bascur

Several new hydrometallurgical plants have been built in the past years, new processes and equipment as well as advanced process control systems are being used to deal with the increasing requirements of safety, quality and production. Plant Information Management Systems are now being recognized as a key infrastructure component of the plant, giving the management, the operators, process engineers, finance, maintenance, and regulatory agencies an integrated view of the operation and providing the links for the (increasingly) multidisciplinary organization. This paper reviews several implementations of Plant Information Systems; real time performance management infrastructure examples are reviewed as a key component of business strategies, such as Mine to Port Planning and Supervision, Metallurgical Mass Balances, Solvent Extraction Composition Statistical Process Control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to illustrate how companies are using the real time and historical information from assets and metallurgical processes to enable and empower people to improve the operations quality, safety and throughput, as well as continuous improvement and innovation initiatives.

Jan 1, 2007

By G. Scamans, J. Lazaro-Nebreda, Z. Fan, J. B. Patel

"Melt quality is crucial for both continuous and shape casting of light alloys and in order to improve it, removal of excessive inclusions, accumulated impurities and unwanted gases becomes necessary. To address this problem, a new multi-purpose high shear liquid metal treatment technology, based on intensive melt shearing by a rotor/stator unit, has been developed. The device ensures achieving uniform temperature and chemical composition and an efficient dispersion of gas and solid phases in the melt with minimal disturbance of melt surface, and can be used, among other things, for de-gassing and de-ironing of Al-alloy melts. Efficient degassing is achieved by dispersing each argon bubble into many small ones, which significantly increases the overall surface area of the bubbles and the time they remain in the melt capturing hydrogen before reaching the surface. This allows using much lower inert gas flow and mixing times than conventional rotary degassing. When applied to Al-alloy scrap, with accumulated iron, the high shear melt treatment speeds up the nucleation and growth of primary Fe-rich intermetallic particles, allowing a faster removal rate. Therefore it reduces processing times, increasing recycling productivity, and facilitates full metal circulation of secondary Al-alloys.INTRODUCTION Aluminium and magnesium alloys are widely considered in various industrial sectors for the purpose of weight saving (Polmear, 1995). In particular, they are used in the automotive sector, where components are mostly manufactured by high pressure die casting (HPDC) because of its simplicity and relatively low cost, but efficiency and mechanical properties are quite low compared with other processes. To date, the main focus to overcome this problem has been for improving the HPDC machinery (Dahle, 2001) but little attention has been paid to the opportunities of controlling the nature and quality of the molten metal supplied to the die. In this way, liquid metal treatment, which involves a variety of physical and/or chemical processing methods to improve melt quality prior casting, is crucial for both continuous and shape casting products."

Jan 1, 2018

By A. Elsayed

Lightweight metals such as magnesium show potential in replacing aluminum alloy castings for engine cradles, cylinder heads and transmission cases. Unfortunately, magnesium alloys are susceptible to entrapping oxides and other impurities during casting that hinder strength and ductility. The current study examined various filter sizes and configurations with the aim of improving the mechanical properties of permanent mould cast AZ91E. The unfiltered casting had a yield strength, tensile strength and ductility of 93.3 MPa, 153.3 MPa and 2.2 % respectively and increased to 96.5 MPa, 167.0 MPa and 3.1 % with the use of a fine mesh filter within the well of the mould. The increased strength and ductility was likely due to the filtered castings containing fewer inclusions on their fracture surfaces as compared to the unfiltered castings.

Jan 1, 2011

Presentation Topics ? Low and Intermediate Level Waste ? Project Location and Site ? Geological Setting ? Key Features ? Project Overview ? Licensing and EIS ? Next Steps DGR Waste Package Inventory Approximately 50,000 packages over 35 years: ? ~40,000 packages or 80% of inventory are LLW Bins ? ~7,000 ILW Shields (concrete boxes) ? ~2,000 resin liner packages

Oct 1, 2010

By S. Onuki, T. Ando, M. Tejima, R. Enomoto, Y. Okada

"Al–Si–Cu–Mg die casting alloys are widely used in the automotive industry, and recent advancements in high pressure die casting technology enable heat treating products to achieve desirable properties. However, CO2emissions associated with die-casting production lines should be reduced to address the global warming issue. In this study, the relation between the microstructures and thermal stability of precipitates formed during isothermal aging at 423, 485, and 558 K of Al-11.0 mass%Si-1.8 mass%Cu-0.2 mass% Mg (JIS ADC12) was investigated using Vickers hardness tests and transmission electron microscopy (TEM). The hardness tests and TEM results showed that Si compounds and Al–Cu compounds enhanced the mechanical properties of the alloy and that the predominant compound affecting the mechanical properties differed between specimens treated at 423 K and those treated at 558 K. Moreover, additional aging at 423–458 K resulted in a material with a Vickers hardness higher than that of the isothermally single-aged material. Differential scanning calorimetry, differential elemental analysis, and selected-area diffraction analysis using TEM suggested that the combination of Al–Cu compounds precipitated at low aging temperatures and Si compounds precipitated during preliminary aging increased the mechanical strength, resulting in a maximum hardness of 130 HV.INTRODUCTIONAl–Si–Cu–Mg die casting alloys have well-balanced mechanical properties, machinability, and cast ability. These alloys are therefore widely used in the automotive industry because of their superior characteristics, accounting for>90% of the aluminum used in die casting production. As a substitute for iron-based materials, these alloys have contributed to the development of lightweight vehicles.Dong et al. (2014) reported that the heat treatment of die casting materials is effective for changing their dimensions under high temperatures as a result of the precipitation of solid-solution elements. Recent advancements in high pressure die casting technology have led to the application of heat treatments of Al–Si–Cu–Mg alloy products to reduce fuel consumption and satisfy customer needs. Although attempts to reduce CO2emissions have focused on fuel consumption in cars and fuel efficiency regulations have become increasingly strict in recent years, CO2discharged from production lines should also be reduced without adversely affecting the properties of the product. Heat treatments for artificial aging after solution treatment (T6 treatment) and after casting (T5 treatment) are CO2discharge sources, which together with a holding furnace account for >80 % of the CO2discharged during the casting process."

Jan 1, 2018