Search Documents

By D. D. Campbell

"The Port Radium mine of Eldorado Mining and Refining Limited lies on the western tip of a large peninsula midway up the east shore of McTavish Arm, Great Bear Lake, about 30 miles south of the Arctic Circle. The mine is serviced by air, 950 miles from Edmonton, and by water, 1,380 miles from Waterways, Alberta.The veins were found, and the copper and cobalt minerals in them reported, by J. MacJntosh Bell of the Geological Survey of Canada in 1899. The veins were investigated by Gilbert Labine and E. C. St. Paul in 1930, and as a result of their work the Eldorado mine was brought into production in 1934. It produced silver and radium ores until 1940, at which time, as the silver orebodies had been mined out and the market for radium was negligible, it closed down. Early in World War II the need for uranium for the Manhattan Project was emphasized, and the mine was reopened in 1942. As a security measure Eldorado Mining and Refining was created a Crown company in 1944. The Port Radium mine has continued to be one of Canada's principal producers of pitchblende concentrates, and to date has about 25 miles of underground workings developed on fourteen levels.Regional GeologyThe general geology of the McTavish Arm area was mapped by D. F. Kidd in 1932 on a scale of one inch to four miles. A great deal of more detailed work has since been done by geologists of the Geological Survey and of Eldorado. The entire area at the end of McTavish Arm lies within the Precambrian Shield immediately east of its western margin. Most of the area is underlain by granitic masses which have intruded a sequence of late Precambrian sediments, volcanics, and hypabyssal intrusives. The pre-granite rocks now occur in extensive, irregular patches and pendants within the granite. Pitchblende deposits have been found in the district in all rock types, but the most favourable host rocks are the cherty sediments of the lower Echo Bay group."

Jan 1, 1949

By A. Ghahremaninezhad, E. Jorjani, A. Riahi, Islamic Azad University, B. Nazari, H. Hani, Z. Manafi

The presence of a high iron concentration, 9.1 g/L, in the raffinate of the Sarcheshmeh copper heap bioleach process led to the formation of various types of jarosite, (K,Na,NH4,H3O)Fe3(SO4)2(OH)6, on the heap mineral surfaces. This study probes iron removal from the raffinate using a bio-oxidation process based on A. ferrooxidans bacteria in the presence and absence of jarosite seed. The jarosite seed was biologically synthesized using A. ferrooxidans bacteria. The effect of solution pH (1.5 to 2.5) and jarosite seed dosage (0 to 15 wt.%) on iron removal was examined. It was demonstrated that the concentration of iron ions present in the raffinate decreased from 9.1 g/L to 2.5 g/L with the addition of 10 wt.% jarosite seed at pH 2 and 130 rpm mixing rate at 32°C. Three different types of raffinate including (1) native raffinate containing 9.1, 3.4, 5.7 g/L of total, ferric and ferrous iron, respectively, (2) bio-oxidized raffinate in the absence of the jarosite seed containing 8.5 g/L total iron (mainly ferric with negligible ferrous), (3) bio-oxidized raffinate in the presence of jarosite seed containing 2.55 g/L total iron (mainly ferric with negligible ferrous) were used in mesophilic, moderate thermophilic and thermophilic bioleaching processes. The results of the flask tests showed that the highest copper bioleaching recoveries of 9.4, 49.4 and 90.8 % were achieved using raffinate (3) with mesophilic, moderate thermophilic and thermophilic bioleaching processes, respectively.

Jan 1, 2016

By Jürgen Kretschmann

The Islamic Republic of Iran is a very important producer of raw materials in the world. The country holds 68 types of minerals, including salt, sand and gravel, chrome, lead, zinc, copper, coal, gold, and iron-ore. With more than 37 billion tons of measured and indicated reserves and 55 billion tons of total mineral resources, Iran is ranked among the 15 major mineral-rich countries. Sangan iron-ore mines (SIOM) is one of the biggest iron ore mining complexes in Iran, located in a remote, but strategically important area near the Afghanistan border. The Iranian government has planned several mining projects in this region for a stepwise development over the next 5 years to satisfy the growing demand of the Iranian steel industry. In cooperation with private companies, these projects shall be realized as sustainable as possible. This paper introduces SIOM and describes socially responsible activities undertaken during the initial development of this mining complex. The effects of these activities will be demonstrated. Unique attributes of the Sangan area have a significant impact on the acceptance of SIOM by regional stakeholders. The government has made several social investments that benefit workers´ families and the community. They are attempts to build social capital for the mining operations and demonstrate a commitment for socially responsible mining to the communities and the local population. They aim to create a balance between the local and regional expectations and requirements and the necessity to secure the corporate profitability at a reasonable and sustainable level. Investment in socially responsible activities is not a choice but a necessity to improve the relations between mining companies and stakeholders in the communities. It is recommended that social investments should be carefully planned and implemented from the early stages of mining activities, and should proceed throughout the life cycle of the mines.

Aug 1, 2013

By Keith Haddock

"The Sheerness Mine, a new surface coal mine located near Hanna, Alberta, went into full production in mid-1995. The mine, which is operated by Luscar’s subsidiary Forestburg Collieries (1984) Ltd., has the design capacity to supply up to 2.1 million tonnes of sub-bituminous coal per year to the adjacent Sheerness Generating station under a 30-year contract. This paper documents the construction phase of this project and highlights the major equipment purchases as well as the construction of the mine facilities. The paper also focuses on some of the areas where cost savings have been achieved that have allowed the mine to come on stream six months ahead of schedule, and under budget. Project ReviewMine DescriptionThe Sheerness Mine is located 25 km southeast of the town of Hanna in southeastern Alberta (Fig. 1). The mining property occupies the western portion of the Sheerness CoalField and borders the Montgomery Mine, operated by Manalta Coal Ltd. in the east, and Highway 36 in the west. The Montgomery Mine and the Sheerness Mine exclusively supply the total coal requirement of the adjacent Sheerness Generating Station. The station is owned jointly by Alberta Power Limited (APL) and TransAlta Utilities Corporation (TAU). APL is the operator. Manalta’s Montgomery Mine has supplied coal to the Sheerness Station since its opening in 1986. Coal is shipped by truck from the mines over a network of haul roads to the coal receiving hoppers located on the east side of Highway 36."

Jan 1, 1997

By M. Staite

This paper analyzed the feasibility of converting a 5kW natural gas SOFC power generator system designed to operate on natural gas to be fuelled by methanol. The analysis included laboratory methanol fuel processing experimentation, methanol reformate SOFC cell testing, and SOFC system mass and energy balance modelling. Methanol fuel processing experimentation indicated that theoretical reformate compositions can be achieved for high temperature (600-900°C) methanol steam reforming. A 6% open circuit voltage decrease and a 10% peak power current density decrease between cell operation on humidified hydrogen and methanol reformate was observed. SOFC system mass and energy balance modelling indicated that a natural gas SOFC system can be converted to operate on methanol fuel with minimal (1%) efficiency impacts, however the systems' thermal integration can be impacted.

Jan 1, 2005

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004

By Gordon T. McKenna

"Syncrude Canada Ltd. is developing new concepts in lease-closure landscape design for its Oil Sands Leases 17 and 22 in northeastern Alberta. Closure planning is becoming an integral part of the planning cycles and of the lease operation. By incorporating closure planning into the day-to-day operation, the company will achieve acceptable lease closure in an economical manner. Ultimately, Syncrude will achieve lower operating costs through innovation in mine planning and a reduction in residual liabilities.New concepts being evaluated for lease-closure landscape design include: designing for closure, use of landforms and natural analogs, self-armouring bouldery ground, robustness in design, landform grading, terrain analysis of reclaimed land, geotechnical hazard assessments, choices in closure design timeframes, passive maintenance, determining post-closure monitoring goals, engineering tailings, engineering other substrates, use of test plots and field demonstrations, geomorphologic monitoring of reclaimed lands, defining closure goals, and visiting other mines. These concepts are being formalized under the new discipline of Landscape Engineering."

Jan 1, 1996

By Glenville A. Collins

IN 1932, Horace Onyett at Oroville, California, built a practical floating washing plant along the general lines as now known, using a 24 in. by 12 ft. trammel; it was fed with a ½ yard dragline bucket, rated then at 200 yards per day. Onyett dubbed his plant a 'Doodlebug' which name has clung to this type of operation ever since. In general, the 'Doodlebug' dredge is the outgrowth of the depression of 1929, wherein many dirt contractors had surplus idle equipment and a few of them ventured to use it for placer mining. Many such plants were impractical and poorly designed and adapted often to locations not suited to the purpose. However out of the general idea came refinements until today dragline dredging has a very definite place in the gold production of the world. Many of the early operators, being mainly contractors without mining experience or technical knowledge of gold saving, geology, or mechanical design, naturally went through stages of trial and error until a workable unit became standard practice. Credit should be given Bodenson Iron Works of San Francisco, who did a notable job of pioneering and building of floating washing plants; also, to Lord and Bishop, contractors of Sacramento, who were among the early operators, and to several others who built and rebuilt their plants until the weak spots were strengthened to take the beating required, and yet deliver a high degree of efficiency.

Jan 1, 1945

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By Z. Q. Yue

Many large rock avalanches and/or landslides have occurred in mountainous regions around the world. Their occurrences are normally rapid and unexpected, which can cause disasters. They have been investigated extensively by many researchers and engineers since the 1903 Frank Slide on Turtle Mountain, Alberta, Canada. They are one of the most peculiar phenomena because the rock debris of more than one million m3 can move over the horizontal distances exceeding those expected from conventional friction physics. This paper presents a gas cause hypothesis responsible for the large rock avalanches. It is the migration and expansion of a certain amount of highly pressurized and dense natural gas mass from deep geological grounds into the mountainous rock mass slopes. The natural gas with high pressure and density can escape from the deep geological ground and flow through faults, weak zones and/or porous channels into the rock mass forming a mountainous slope. The rock mass forming the slope has the high tensile and compressive strength and can resist the initial loading of the gas mass migrated into and stored in their voids, pores, holes, gaps, openings, apertures and cavities. With time, more and more gas mass from deep ground can migrate into and stored in the slope rock mass. Eventually, the peak equilibrium of forces and deformation reaches. The expanding power of the gas in the slope rock mass would instantly and rapidly break, erupt and/or explode them. The compressed and dense gas mass would mix, flow and expand together with the broken rock debris mass and continue offering their remaining expanding powers to the moving and sliding debris mass. As a result, the rock debris of large volume can reach the runout distances exceeding those expected from the conventional friction physics. The gas would escape into the sky and the solid rock debris would remain on the ground spreading over large ground area. The 1903 Frank Slide is examined to show this gas cause and mechanism in mountainous regions.

Jan 1, 2015

By Sylvie Lévesque, Cory Hennessey, Daniel Amariei

"In the iron ore industry, fine particles recovery is an important concern in terms of process performance and production costs. Continuous efforts are thus devoted to increase the efficiency in handling these fines.The Reflux Classifier (RC) is a relatively new technology that is mainly used in the coal and industrial minerals industries. The operating principle of this system is based on three mechanisms: hindered settling, autogenous dense medium and lamella settling. A preliminary evaluation of the Reflux Classifier technology for the beneficiation of iron ore fines was formerly done at the pilot scale using a RCTM300 unit. The good results obtained, using iron ore fines from screened spiral stream, made this technology very attractive for the iron industry. However, the high capacity of the RCTM300 unit (1–3 t/h), makes it unsuitable for R&D purposes. Thus, a smaller unit, the RCTM100, was assessed to validate the performances obtained with the RCTM300.This paper summarizes the performances obtained with the RCTM100. The challenges of the scale-down related to the adaptability of this technology to the iron ore industry are also presented. The results are compared to the RCTM300 performances, as well as benchmarked against sink-float tests. The metallurgical results on feed and products issued after the test work with the RCTM100 unit are supported by mineralogical characterization using a Mineral Liberation Analyzer.INTRODUCTIONFine particles recovery by physical separation means is a historical concern (Holland-Batt, 1992; Peukert and Wadenpohl, 2001; Srivastavaa et al., 2001; Majumder et al., 2003). Attempts to improve fine particle recovery at the laboratory, pilot and industrial scales adopting different strategies with traditional equipment or assessing new promising devices such as the MGS (multi-gravity separator), the Kelsey jig, the Yang jig, etc. (Kim, 2002; Goudreau, 2008; Kerr, 2012) have yielded variable success."

Jan 1, 2016

By J. McCreedy

This paper reviews new methods of exploration for metals and new techniques of mining the deposits and extracting the metals from their ores. Examples of mining innovations are taken from Inco's Thompson Operation. The importance of presenting a favorable image of the industry to college students and young people deciding on a career is stressed.

Jan 1, 1971

By Ltd. (CYMCO) Technology Center Yunnan Metallurgical Group Co., S. Jian, T. Song, J. D. Miller

"As sulfide zinc ore deposits become exhausted, nonsulfide zinc ore deposits become the other resource for zinc production. However, flotation for zinc recovery from nonsulfide deposits is much more difficult than the flotation of sphalerite from sulfide deposits and may become an option for zinc production only if a suitable processing technology is developed. In this regard, research efforts are being devoted to the flotation of nonsulfide zinc oxide minerals. Some common methods which have been used for the flotation of zinc oxide minerals include sulfidization-flotation, activation, and direct flotation with anionic and cationic collectors. The traditional flotation techniques have low efficiency and difficulty in separation and recovery of the zinc minerals from gangue minerals, for example, smithsonite (ZnCO3) from other carbonate gangue minerals and hemimorphite (Zn4Si2O7 (OH)2·H2O) from silicate gangue minerals. In this study potassium lauryl phosphate was evaluated as a collector for the flotation of nonsulfide zinc minerals. Results from contact angle and microflotation experiments at pH 6–9 show that hemimorphite (Zn4Si2O7 (OH)2·H2O) can be floated from quartz and that smithsonite (ZnCO3) can be floated from calcite. However, when dodecylamine, which is a common collector reported in literature for the flotation of nonsulfide zinc minerals, was used as collector, no significant difference between nonsulfide zinc minerals and gangue minerals was observed at any pH value. Initial evaluation suggests that potassium lauryl phosphate is effective at low concentration and may be a promising collector for zinc oxide mineral flotation.INTRODUCTIONBefore the twentieth century, zinc was mainly produced from nonsulfide ores (Large, 2001; Gilg, Boni, & Cook, 2008). With the development of differential flotation processes in the late 19th century major production switched from nonsulfide zinc sources to sulfide zinc ores (Hitzman, Reynolds, Sangster, Allen, & Carman, 2003; Gilg et al., 2008). However, as it is becoming more difficult to find new sulfide ores, recovery from nonsulfide deposits is being considered. Nonsulfide flotation for zinc recovery is much more difficult than the flotation recovery of sphalerite from sulfide deposits and may become an option for zinc production if a suitable technology is developed. Zinc and lead oxide ores are difficult to beneficiate ores due to their similar floatability with gangue, high solubility in water, and the influence of slimes (Fa, Miller, Tao, & Li, 2005). In order to improve the performance of oxidized minerals, lots of effort is being devoted to this field of study (Ejtemaei & Mahdi, 2014)."

Jan 1, 2016

By D. K. Fountain

"High metal prices and advanced technology in open-pit mining methods have resulted in considerable interest in the development of large, low-grade mineral deposits. Brenda Mines Limited is presently testing such a deposit of copper-molybdenum mineralization near Penticton, British Columbia.The mineralization of economic interest at Brenda has a total metallic sulphide content of between 1 and 1.5 per cent. This sulphide content approaches the limits of detectability of standard geophysical methods. How-ever, due to a favourable geological environment, it has been possible to utilize the Induced Polarization Method to outline the mineralization at the Brenda property."

Jan 1, 1968

By S. Shrestha

Magnesium-based alloys are of growing interest for many industrial applications due to their favourable strength-to-weight ratio and excellent castability. Mass reduction has advantages in many industrial sectors for example, in automotive, a reduction in mass improves fuel economy and can lead to more efficient mechanical systems by reducing the weight of moving parts like wheels, gears, pistons. However, the relatively poor corrosion and wear resistance limits the use of magnesium and its alloys in many potential applications. The patented Keronite® plasma electrolytic oxidation (PEO) process enables manufacturers to overcome such problems and, in its latest generation equipment has been developed to industrial realisation for high volume production. This paper presents microstructural characteristics and corrosion performance of two most widely used high pressure die-cast magnesium alloys AZ91D and AM6OB with a duplex corrosion protection coating system that comprised a thin Keronite pre-treatment followed by a subsequent automotive grade final powder coat.

Jan 1, 2006

By David S. Wong

With air emission limits for total particulates continually tightening, management of `potroom dust' or airborne particulates from aluminium smelting potrooms is of increasing importance. To better understand how settled and airborne particulates are generated within a potroom, methodologies have been developed to sample and analyse the compositional signature of dust, in relation to its sources. During a smelter case study, these methods allowed tracking of mineralogical phases in dust across a range of potroom locations, showing that the mechanisms of dust generation do vary spatially and vertically in a potroom. Such methodologies may also be applicable to other metallurgical industries.

Jan 1, 2011

By T. Purushotham, B. Samanta

ABSTRACT; The shaft bottom junction in a mine ventilation system is an important source of shock loss due to the combined effect of bend and area change. The occurrence of high-volume ?ow rates through this con?guration can potentially result in high energy losses. The current research examines the process of shock loss at a characteristic shaft bottom junction of an underground coal mine. Investigations are per-formed on both laboratory-scale models and three-dimensional computational ?uid dynamics (CFD) simulations, under both exhausting and forcing shaft bottom conditions. The effects of the plat roughness and the shaft bottom length on the shock loss factor values are also examined. The studies show that the combined effect of bend and area changes that occur at the shaft bottom junction results in shock loss factors that are much higher than those values resulting from abrupt area change only. The transition from a smooth wall condition to an unlined rough airway condition (relative roughness, e/d = 0.112) can increase the shock loss factors by 40%. The effect of shaft bottom length on the shock loss factor has not been clearly established due to con?icting results produced by scale model studies and the CFD simulations.

Jan 1, 2010

By J. Basi, J. A. Finch

ABSTRACT Testing the effects of bubble size (Db) in a Mo cleaning ?otation column at Highland Valley Copper mine indicated that increasing the proportion of small (< 1 mm) bubbles signi?cantly improved column metallurgical response, compared to typical operation. The results were a three- to four-fold Mo recovery increase and a 1 to 2% Mo (absolute) concentrate grade increase. The improvedcolumn operation produced a 4% Mo plant recovery increase. This study also showed that modelling the ?otation rate constant (k) as an inverse square function of Db was more accurate than considering k to be inversely proportional to Db.

Jan 1, 2010

By G. P. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Stress-corrosion cracking (SCC) tests were conducted in the near-neutral pH standard solution, NS4, and in an actual soil solution, using four-point bending at high a stress ratio and low frequency conditions very similar to those of operational pipelines. Pitting incubation appeared first and then pitting initiated and grew in both solutions although there were many more pits on the specimen tested in soil purged with 5% CO2 + 95% N2 than in the specimen tested in NS4 solution purged with the same gas. These observations show that samples in soil solution are more susceptible to pitting than those in NS4 solution. When the pit reached a critical size, the increased stress concentration around the pits, resulted in the transition to a crack.

Jan 1, 2005

By S. Yadav, T. G. Murthy, C. Saldana

"An experimental study has been carried out in order to study the deformation of porous brittle materials under plane strain indentation. Gypsum, which is well known model system for understanding the behaviour of soft rocks, is used in this study. The effect of wedge angle is investigated in this research through this series of experiments, using wedges of 3 different apical angles. High-speed, high-resolution images are captured using a CMOS camera during the experiment. The images obtained are analyzed using a Particle Image Velocimetry (PIV) algorithm in order to obtain the evolving velocity, strain-rate and strain fields.INTRODUCTIONThe problem of indentation, which is usually referred to in the context of hardness testing is ubiquitous as a material characterization technique for a large class of solids. Mechanical properties of materials such as yield stress, flow stress, fracture toughness, elastic moduli etc. can be related to the hardness of a given solid. The indentation problem involves a given material or solid (whose properties are to be determined) indented by a relatively harder material (indenter) allowing the solid to undergo plastic deformation, which is then related to the yield stress of the material. The problem of indentation and its variants see many applications ranging from mining and petroleum industry, infrastructure industry, manufacturing, and biomedical sectors. Indentation has been extensively studied in metals, with accurate measurement of deformation parameters, stresses and comparison with analytical solutions. On the other hand, understanding of indentation in other class of solids such as cellular solids, porous solids, rocks, and soft solids is still nascent. In case of rocks, a comprehensive understanding of the indentation problem is very crucial because of the obvious applications in mining, petroleum and infrastructure sectors. The inherent porosity, the brittle nature of the rocks, adds to the complexity of indentation in these porous brittle solids. Various theoretical models with degrees of simplifying assumptions have been proposed to study the indentation in rocks. The most common model used in the study of indentation in rocks is a cavity expansion model, wherein a blunt indenter indenting into a rock is approximated with the expansion of cylindrical or spherical cavity in an elastic-plastic material. Complementary studies in understanding fracture initiation and propagation due to indentation has been largely based on the studies of traditional brittle materials such as glass."

Jan 1, 2015