Search Documents

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By Ross D. Lawrence

"Comparable transaction analysis is the best known of the market approaches to valuation of exploration-stage mineral properties. The analysis of option and farm-in agreements can also provide useful guidance to valuators. While such approaches can be distorted by incomplete analysis, market-based methods are capable of providing consistent, credible results when carried out carefully with due consideration paid to all factors which buyers and sellers consider when dealing in the real market.RÉSUMÉRoss D. Lawrence graduated from the University of Toronto with a B.A.Sc. (Applied Geology-1956) and an M.Comm. (Mining Finance-1959). As a student and following graduation, he worked across Canada on a variety of mineral exploration projects.In 1962, he was one of the founders of Watts, Griffis and McOuat, and has practiced as consulting engineer since then. For the past 20 years, Mr. Lawrence has headed up the WGM valuation practice, responsible for a group of professionals which has carried out scores of valuations of mineral properties and mining companies. He is a Certified Minerals Appraiser of the AIMA and an active participant in professional affairs.INTRODUCTIONMineral properties without defined resources present one of the most challenging tasks to the mineral valuator. You will hear from others at this conference about the use of cost and income approaches to the problem of valuing exploration properties. This paper will concentrate on market-based approaches. Market based-approaches are based on the principle of substitution and include such techniques as:??Comparable transaction analysis (sometimes referred to as sales comparison analysis).??Farm-in commitment analysis??Rules of thumbAre there any valuation standards available to assist the valuator? In Canada there are none that apply to the valuation of mineral assets or securities. This problem is being addressed, at least in part, by the CIMVal committee of the Canadian Institute of Mining, Metallurgy & Petroleum (CIM)1. Further, the recently established Canadian Association of Mineral Valuators will be giving consideration to the adoption of valuation standards."

Jan 1, 2003

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By H. C. Cooke

This paper will discuss two comparatively unrelated subjects; first, a general review of the advances made at the more important properties in the last year; and second, a statement of the conditions controlling the deposition of the copper ores in the Rouyn area, as determined by last summer's field work. FIRST PART Development has been very rapid since I stood before the Institute one year ago to discuss this same subject. Then, there were many properties on which gold had been discovered, any of which might develop into a mine. Further work has eliminated the most of them as possible mines, or at least has shown that before they can attain that status further discoveries must be made on them. Then, all gold veins held forth much the same promise; now the indications are that one particular type of gold vein is of greater prospective value than others. Then, all eyes were turned toward gold as the metal of prime economic importance; now copper has taken the centre of the stage, and gold is distinctly in the background.

Jan 1, 1926

By T. J. Wells

THE blast furnace is the base of the steel industry, since there is no commercially practical way of converting iron ore directly into steel. In three hundred years, the blast furnace has developed from a small unit using charcoal as fuel and producing about one ton of iron in twenty-four hours to a furnace making upwards of 1,500 tons a day. The principle of the blast furnace is briefly this: A descending column of stock, consisting of ore, fuel, and flux, is met by an ascending stream of gases, consisting in part of gases formed by the combustion of the fuel and in part of pre-heated air which is blown into the lower part of the furnace. The flux combines with the impurities in the ore and the ash in the fuel to form slag, which is drawn off as liquid.

Jan 1, 1943

By Jonathan Tsang, Ali Merati, Jonathan Beddoes

Due to economic factors, many aircraft in service today have been operating for more than 30 years even though they were initially designed with a service life of 20 years. Improved damage management models are therefore needed for use in life prediction and management of the aging fleets of aircraft. Currently, the generally accepted procedure in fatigue life prediction methodologies is to back calculate the equivalent initial flaw size (EIFS) using established long crack growth data. However, it was observed from studies carried out at the National Research Council Canada that nucleation and short crack growth constitute up to -95% of the fatigue life. As a result, it seems that the significance of the short crack regime has been underestimated and must be further investigated and fully understood before an accurate holistic life prediction methodology can be realized. Unlike long cracks, local microstructural features such as grain boundary, grain size, inter-particle spacing, and texture play dominant roles in the behavior of short cracks. An extensive study has been carried out to evaluate different crack detection and monitoring techniques in the short crack regime for AA2024-T3. The results will be presented in detail.

Jan 1, 2004

By F. W. Gray

Ideal utilization of the heat energy in coal should theoretically be secured by supplying each atom of combustible material present with the exact quantity of oxygen necessary for complete combination. An intimate and equal admixture of the fuel particles with air is therefore to be sought. Coal, or the combustible substances of which coal is composed, may be used in solid or liquid or gaseous form. The use of coal in small particles intimately mixed with air is, in effect, a specification of coal in pulverized or dust form. There has been much important development of this manner of using coal, which may be instanced as the outstanding advance in the use of coal as a solid. The completeness and efficiency of combustion in a properly designed dust-fired furnace permits the use of locally available coals of inferior quality, and enables them to be used commercially instead of imported coals of better quality. That is to say, some grades of coal of low calorific value, that are not economically useable in lump form on grates, are useable in pulverised form, because of the more complete combustion thereby obtained, and the consequent more efficient results. In the case of coals that are unsuitable for steam-raising in grate-fired furnaces, because of clinker troubles, (arising usually from a combination of high sulphur content and low-temperature fusibility of the ash content) use in pulverised form has obvious advantages, and in addition gives the benefit of any heat units that are contributed by free sulphur in the coal.

Jan 1, 1924

By J. W. Senn

A magnesium alloy modeled after commercial alloy WE54 was thermomechanically processed and characterized to understand the mechanisms by which its texture can be randomized, as reported by Ball and Prangnell [1]. Samples were deformed in plane strain compression to prescribed strain levels at temperatures high enough to prevent cracking and then recrystallized. The deformation texture is very similar to that observed after plane strain compression (e.g., rolling) of other Mg alloys, such as common AZ31. However, the texture can radically evolve during recrystallization. Annealing above the precipitate solvus temperature results in a nearly random recrystallization texture where the initially strong basal texture is completely eliminated. Annealing below the solvus temperature produces a recrystallized texture similar to conventional Mg alloys, i.e., a weakened basal texture. If this same material is then annealed above the solvus to promote grain growth, a randomized texture evolves, which is similar that of samples simply recrystallized above the solvus. It is hypothesized that a sort of preferred growth mechanism, whereby grains with random orientation grow faster than those with the original basal texture, contributes significantly to the texture randomization observed in wrought magnesium alloys containing rare earth elements.

Jan 1, 2006

By Michael Hopp

The beginning of the electroforming technology dates itself on the beginning of the industrial revolution 1800 to 1820 approximately. Basis was the existence of electricity in order to be able to drive the electro-form-process. With the development of the electroforming, big names of the science-history, like Michael Faraday (1791? 1867), Sir Humphry Davy (1778?1829), Max Schlöter (1878?1946), Werner von Siemens (1816?1892), and many others. Already about 1840, the first monograph originated to electroforming (38). While in the first years the electro-forming most extensive only to the coating of art - or other usefulness-objects was used. At the beginning of the 20th century the formation of objects from pure metals became more and more, later also from alloys to application. One of the first bigger electroforming factory, the ?Württembergische Metallwarenfabrik? was working 1894 in Geislingen / Steige, Germany. In the industrial application, the electroforming-technology is to be imagined away for miscellaneous coatingtasks and the form-body-preparation no longer today (18). A little bit confusing is the german name ?galvano-technology?. It based on the Italian physiologist and naturalist Luigi Galvani (1737 ? 1798). This technically seen is however wrong, right, the name is electroforming. The physical bases were founded mainly by Michael Faraday and Sir Humphry Davy.

Oct 1, 2003

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By Chigova. Terence

In 2008, Anglo installed the Modular IntelliMine® System at its Kleinkopje Mine (AKK). As part of this deployment, Anglo also used the Change Management Consulting Service offered by Modular to ensure a successful installation. This paper outlines the benefits that AKK has realized through the deployment of the system, including a 15% improvement in tonne/kilometers per hour (TKPH). The mine benefited from the improvements provided by the system almost immediately by utilizing change management to more effectively integrate IntelliMine technology into their processes. This case study includes details about the deployed system, the implementation of change management, and recommendations to ensure success in future projects.

May 1, 2010

By D. B. Stewart

This paper reports on an investigation undertaken to determine the exhaust gas temperatures of operating underground mining equipment. The effectiveness of platinum catalytic purifiers is discussed. From exhaust temperatures, it is concluded that LHD engines are highly loaded, haulage truck engines are moderately loaded and utility vehicle engines are lightly loaded.

Jan 1, 1979

By D. Pearcey, S. T. Vessey, V. Hegde, J. Staples

"Pellet quality has taken on a new dimension during the last ten years. Quality in the seventies was generally defined as adherence to certain physical and chemical specifications. Today, the talk is in terms of how the business is managed, how customer's expectations can be exceeded, not only in product quality, but in service responsiveness.Coke breeze and flux additions, lower silica levels, and improved furnace control practices have all contributed to the improvement of pellet physical and metallurgical properties. Statistical process control has provided additional insight into the parameters that affect pellet quality.Increased customer contact and product quality surveys have heightened our awareness of customer needs and also provide direction for quality improvement test work. Current work is focussed on improving reducibility and understanding the relationship between tumble, fired compression and metallurgical properties.This paper will review the Iron Ore Company of Canada's efforts during the past decade and describe some of its initiatives for the future.IntroductionThe Carol Pellet PlantThe Iron Ore Company of Canada's Carol Project is located in Labrador City in the southwestern portion of Newfoundland and Labrador , approximately 965 Ian northeast of Montreal. The project consists of mining facilities, beneficiation complex and a pellet plant, which began operations in 1962. The pellet plant consists of six Dravo-Lurgi straight grate machines, regrinding, filtering and balling facilities. The current capacity of the Carol pellet plant is approximately 10.5 million tonnes , while the concentrator has the capacity to produce about 18 million tonnes of concentrate.The orebody consists of specular hematite, magnetite and small quantities of limonite and goethite. The average grade of the orebody is approximately 39% iron."

Jan 1, 1991

By D. Laguitton

The basic chemistry of a1•senic related to its dissolution and subsequent precipitation in gold-mine waste waters is discussed. The lime addition methods provides the most economic treatment of arsenical slurries, but requires a careful control of the oxidation of Asm into Asv, of the pH (>12) and the filtration of the precipitate. If arsenic levels below 0.5 mg/ l are required, a modification of the method by phosphate addition must be considered.

Jan 1, 1976

By B. S. W. Buffam

"The property of Aunor Gold Mines, Limited, is in Deloro township, Ontario, about 3 miles southeast of Timmins. It consists of a group of eleven claims between the Buffalo Ankerite and Delnite mines.In the autumn of 1909, two brothers, John A. and W. S. Mitchell, joined the 'gold rush' to Porcupine. By the time they arrived the township of Tisdale, in which the Hollinger and Dome discoveries had been made, was staked solid but they managed to locate four claims in the northern part of Deloro township. Sufficient surface work was performed to bring the claims to patent in 1915. Following the Porcupine fire the Mitchells left the north to follow the oil developments in southwestern United States. In 1935 because of the rise in the price of gold and the successful development of the l3uffalo Ankerite and Delnite mines, they returned to Timmins and organized Augite Porcupine Mines, Limited, which combined the original four claims in Deloro and two adjoining claims controlled by Montreal River International Silver Mines, Limited. There were few rock exposures on the property, and as the overburden was generally deep surface exploration was impracticable. A programme of diamond drilling was, there; fore, undertaken in an endeavour to locate the western extension of the orebearing formation of the Buffalo Ankerite mine. This drilling was started in August 1936, and 5 months later ore was intersected at a depth of 500 feet on the south boundary of the property."

Jan 1, 1954

By J. D. Little

"THE SALMO PROPERTIES of Canadian Exploration, Limited comprise forty-one Crown-granted mineral claims situated on Iron mountain between Sheep creek (on the north) and Lost creek, some eight miles southward from Salmo, in the Nelson mining division (see Figure 1). On these claims there are at present four operating mines. These are, from north to south, the Dodger, Feeney, and Emerald, all tungsten mines, and the Jersey, a lead-zinc mine, about 7,000 feet south of the Dodger. About midway between the Dodger and the Jersey is a fifth mine, the Emerald lead-zinc mine, which was the first producer in the area but has been inactive since 1926. The locations of the mines are shown in Figure 2.Records of prospecting and claim staking on Iron mountain -which owes its name to the presence of large iron-stained outcrops -go back to 1895. The first recorded owner of the claims that form the old Emerald lead-zinc mine was John Waldbeser who, in 1908, did considerable work and produced 426 tons of lead ore valued, at the then price of lead, at $7,000. This ore was chiefly lead carbonate and was taken from the surface outcrops of two bands of ore that form the Emerald orebodies. In 1909, the Emerald was the largest lead producer in the Nelson mining district."

Jan 1, 1953

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986

By G E. Craig, W. M. Williams

A simple, easily constructed apparatus suitable for the zone refining of iron and other reactive materials is described. After eight passes at one inch per hour, the iron produced showed a marked drop in hardness to 49 Brinell. In addition, an arbitrarily -defined recrystallization temperature was lowered by about 35°C and the rate of grain growth greatly increased. CERTAIN materials, of which iron is one, are so reactive that they cannot be zone refined in any known container without becoming contaminated. For such substances, the floating zone method ( 1) may be used. In this method, the specimen is supported vertically in an inert atmosphere and the molten zone supports itself by its own sur-face tension. The method was first applied to silicon (2) and has since been used for other reactive metals such as zirconium and titanium. Smith and Rutherford (3) have previously reported on the floating zone refining of iron; the efficiency of the method for reducing the car-bon content was demonstrated on

Jan 1, 1962