Search Documents

By Stuart J. Schofield

Introduction The study of the ore deposits of British Columbia is one of fascinating interest not only from a scientific but also from a commercial standpoint and certain wide problems in connection therewith have interested me for some years. Several of these problems have been set forth in papers presented before this Institute on previous occasions. In 1918 it was pointed out that the commercial ore deposits of British Columbia, with one exception, were associated with the granodiorite batholiths of upper Jurassic age. This was followed, in 1922, by a discussion of the ore deposits of British Columbia in which the mineral belts of the province were defined and named, showing a zonal arrangement of ores in which the Pacific coast deposits are characterized by the presence of copper, while the interior belt is marked by the presence of silver, lead, and gold. Methods Of Investigation In reading various reports on the economic geology of British Columbia one is struck with the fact that the mineral veins may be arranged as a system and further examination will show that such a system follows two main directions, one northeasterly and the other northwesterly, both related in origin to the same force.

Jan 1, 1925

By Umbreen Agha, Stephan L. Chryssoulis, A. Margaritis

"The deportment of gold in samples of the biooxidation feed and product from the Harbour Lights mine in Western Australia was determined using optical microscopy and microbeam techniques such as Secondary Ion Mass Spectrometry (SIMS), Time-of-Flight Laser Ionization Mass Spectrometry (TOF-LIMS), and Electron Probe Microanalysis (EPMA). The main objective was to determine the mechanisms by which acidophilic bacteria (Thiobacillus ferrooxidans) liberate refractory gold which is locked in a sulphide minerals host as visible gold inclusions (> 0.1 µm) and as submicroscopic or 'invisible' gold.Using the integrated mineralogical approach approximately 99% and 100% of the assayed gold in the biooxidation feed and biooxidation product was accounted for. The results were compared to and verified by chemical assays.The gold deportment study indicates that during biooxidation, locked visible and 'invisible' gold is rendered cyanidable by the direct action of Thiobacillus ferrooxidans as well as indirect chemical leaching. Visible gold which is enclosed in sulphide minerals is liberated or partially exposed and is therefore rendered cyanidable as the host mineral is oxidized and dissolved. 'Invisible' gold either coalesces on the surface of the host sulphide mineral as the particle is dissolved or is released into the liquid phase and immediately adsorbs onto the surface of other ore particles with a net negative charge.The shakeflask suspension indicates that direct bacterial oxidation pits and channels correspond to zones of 'invisible' gold and arsenic (in pyrite) enrichment in the host sulphide mineral."

Jan 1, 1996

By Marcel M. Djivre

The paper will outline the destructive test methods and test procedures including the evaluation criteria currently used at the Materials Testing Laboratory (MTL), Sudbury, Ontario, Canada, a laboratory approved by the Ontario Minister of Labour for the purpose of testing or examining mine shaft ropes or other hoisting appliances. For the evaluation of the mechanical properties of rope samples used in "ultra-deep" single-lift shafts, additional discard criteria used in Ontario, Quebec and South Africa shall be presented. Most of the methods and test procedures currently used at MTL can also be found in the current CSA G4-00 Standard, Steel Wire Rope for General Purpose and for Mine Hoisting and Mine Haulage, published in November 2000. In this latest or sixth edition of CSA Standard G4-00, a new Clause 14 has been added outlining the requirements for in-service destructive testing of steel wire ropes for mine hoisting applications. The CSA G4-00 Standard is also intended for the manufacturing of new ropes, and includes requirements for raw materials and construction features for round strand and flattened strand rope, and locked coil rope in bright and galvanized finish. To-date the Ontario Mining Regulations require only that destructive test of new ropes be performed in accordance with CSA Standard G4-00, but does not require conformity to the Standard, and on the other hand the inservice wire ropes are required to be tested in accordance with CSA G4 and thus require conformity. The author recommends that the Ontario Mining Regulations (and regulations of other mining jurisdictions) be improved in order to ensure quality control in the manufacturing of wire ropes destined for mines in Ontario (and Canada). Also, the author recommends the revision of the CSA G4-00 Standard by the technical committee in order to address manufacturer?s concerns with respect to compliance, and harmonize the Standard with Internationally recognized Standards.

Apr 1, 2005

Productivity and efficiency of diesel-powered underground trucks and LHDs can be enhanced through the application of a range of advanced technologies. In addition, these machines are subject to ever more stringent emissions control requirements. This paper will review how various technologies can improve usability, maintainability, and performance of LHDs, through a number of examples. The use of instrumentation and monitoring to understand the role of operator practice on mucking efficiency, as well as the use of finite-element analysis to evaluate structural design, and the use of control techniques to modify operator inputs and hence decrease power consumption, will be presented.

May 1, 2002

By A. R. Farkoosh

Al-Si based alloys have been recently used by automotive industry for highly stressed engine applications. Due to severe working conditions of the engine parts, existing alloys hardly endure high pressures at high temperatures. This necessitates alloy modifications to enhance the elevated temperature performance. In this study, the effects of trace nickel additions on the microstructural and mechanical properties of A356+0.5Cu alloy have been investigated at different aging conditions. Electron probe microanalysis (EPMA), scanning electron microscopy (SEM) and X-ray diffraction (XRD) are used to study the microstructural changes. Aging curves have been obtained by hardness measurement. It was seen that the presence of additional nickel introduced many complex intermetallic phases within the microstructure which led to improved high temperature mechanical and aging response.

Jan 1, 2011

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By J. A. Drozdiak, W. Tse, P. P. Rosario

"In a recent publication (SAG 2015), we presented a non-conventional high pressure grinding roll (HPGR)-ball mill circuit as a lower capital cost alternative to the “standard” HPGR circuit. The circuit was designed for the treatment of a hard ore and relatively high tonnage (50,000 t/d). That paper provided details such as flowsheets, layouts, and equipment lists for the two options and compared their calculated capital costs demonstrating significant savings for the proposed circuit. This paper extends the analysis to a third option, a traditional semi-autogenous ball crushing circuit, giving the same level of details and now including the operating cost estimates for all three options for a more comprehensive analysis. Moreover, this work also provides information about the strengths and weaknesses of the non-conventional HPGR circuit when compared to the “standard” HPGR option.This study demonstrates that the proposed non-conventional HPGR-based circuit not only provides a lower overall capital costs for the project if compared to a “standard” HPGR circuit but also brings the capital cost to the level of the traditional semi-autogenous grinding (SAG)-ball mill circuits. In addition, the innovative HPGR circuit provides similar operational cost savings of the “standard” HPGR and thus a significant advantage when compared to the SAG option. With the current capital cost sensitivity for most greenfield projects, the proposed alternative circuit should help make HPGR-based circuits more competitive and thus promote the utilization of a technology that enables higher energy efficiency and reduced greenhouse gas emissions. INTRODUCTIONThe application of high pressure grinding roll (HPGR) technology in comminution circuits is well established for the processing of cement, diamonds and iron ore (Broeckmann & Gardula, 2005), and over the past 10–15 years, this technology has slowly been applied to hard ores in high-tonnage precious and base metal operations. Unfortunately, under the current economic climate, the ability to finance large capital projects has become very difficult and companies tend to have an easier time securing funding if the capital expenditures (CAPEX) are low with a proven process method. The traditional semi-autogenous grinding (SAG) mill / ball mill circuits easily fit into this mould, having been installed in countless plants around the world over the past 30 years with relatively low capital requirements. In contrast, it has been well-documented that HPGR-based circuits are capital intensive with complex material handling systems (Seidel, Logan, LeVier, & Veillette, 2006). Although these circuits benefit from reduced operating costs with the increase in energy efficiency and the elimination of steel grinding media (Rosario, Boyd, & Grundy, 2009), if the company is unable to secure financing to build the plant, these advantages remain out of reach. With the current trend to retrofit existing SAG circuits with a secondary crushing circuit to achieve design throughput, the opportunity to circumvent this gross inefficiency by making HPGR-based circuits more capital friendly would greatly benefit the industry."

Jan 1, 2016

By R. Tipman

"In 25 years, processing of tar sand progressed from two small pilot plants to two major commercial operations owned by Syncrude and Suncor. These plants mine tar sand and extract the bitumen which is then converted into a synthetic crude oil. Considerable research on extraction of bitumen from tar sand has been undertaken by these two companies as well as other major oil producing companies, private individuals, universities and the federal and provincial governments. These studies have produced a number of alternate processing schemes which have yet to be commercialized. The producing companies are focusing their efforts on achieving increased processing efficiency, which includes improved bitumen recovery, reduced unit cost, energy conservation, and equipment reliability. In this review, the Syncrude process and examples of new process developments will be briefly described. IntroductionTwenty-five years ago, tar sand processing was limited to two pilot plants owned by Cities Service Athabasca Ltd., and Great Canadian Oil Sands. Earnest Manning was Premier of Alberta and was inviting proposals for the construction of a commercial tar sands plant. The invitations called for a much larger operation than those which had been undertaken in the past. All of the previous attempts at commercial operations up to 1960's had failed, largely because of a poor technical understanding of the process requirements, lack of suitable equipment, and lack of adequate capital. The previous record was not good. The pending new large scale plant was based on improved but not proven technology and equipment, which were developed from the pilot plant studies. In addition, the surplus of conventional oil in Alberta and low world oil prices were factors reducing the need for such a plant."

Jan 1, 1987

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By James F. Archibald

A research effort has been undertaken, under WSIB sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials (TSL?s), typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and boltand- mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen?s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. Both conventional and innovative TSL-type surface lining materials were subjected to ?rockburst? exposure in rigorously-controlled blast trials. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently-available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validates that thin, sprayon linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

May 1, 2003

By S. Kelebek, E. Yalcin

This paper reports bulk flotation characteristics of a pyritic gold ore sample from the Barry District, Quebec using isopropyl and amyl xanthates. The ore sample was highly floatable with particles showing tendencies for self-aggregation that was most apparent in the first stage of flotation. A possible reason for this is discussed. The gold concentrate grade-recovery performance with respect to the particle size is presented for the rougher-scavengers as well as for the cleaners. The effects of copper sulphate as an activator, fuel oil and NaSH as a sulphidising agent are discussed along with the recovery by size behaviour.

Jan 1, 2011

By Royston Colbourne

Objectives Of Presentation - Identify specific risks - A fresh look at risk - Provide a moment reflection on risk - Open discussion on risk A route to solution and advanced thinking.

May 1, 2010

By G. A. Gross

"Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained from iron-formation; another 20 per cent was formed by natural enrichment processes.Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical com-position and environment of deposition are of special significance in their evaluation as ore.The properties of the ores, including grade, beneficiation qualities and minor element content in taconites, metataconites and naturally enriched ores, reflect characteristics of the primary stratigraphie units from which they are derived. A detailed description of the stratigraphie facies is essential for efficient utilization of these source beds."

Jan 1, 1966

By M. C. Harris

"Excess Gibbs energy is a thermodynamic parameter which quantifies the difference between the value of the Gibbs energy for a real mixture and that for an ideal mixture. More specifically the partial molar excess Gibbs energy of a species (i) in a mixture is indicated by the change in the overall excess Gibbs energy of the solution as the number of moles of species (i) changes while keeping temperature, pressure and the number of moles of all other species in the solution constant. Generally it is obtained from the activity coefficient which in turn can be obtained for a species in a mixture using a variety of models. The most widely used method is to use UNIFAC. Flotation is probably the most important process in the concentration of minerals and requires the use of reagents such as collectors and frothers. There is abundant experimental data which illustrates that collectors of different alkyl chain lengths will change the contact angle and that frothers of different structures and molecular weights will result in changes in key flotation properties such as froth behavior, surface tension and critical coalescence concentration. In this paper it is shown that there is a strong linear relationship between measured parameters such as froth volume/height, surface tension, critical coalescence concentration and contact angle and the partial molar excess Gibbs energy of the molecules used. Proposals are made to explain these correlations.INTRODUCTIONAs is well known froth flotation is arguably the most widely used process in the separation of minerals. In broad terms the process relies on the use of reagents known as collectors to adsorb onto a mineral surface and thus render the mineral particle hydrophobic. Alkyl thiolates are very commonly used for this purpose. The hydrophobicity is induced as a result of the alkyl group’s molecular structural properties which results in it forming a non-ideal mixture with the process water. Surfactants (or frothers) are typically alcohols and are known to lower the surface tension of the system and also inhibit bubble coalescence and reduce bubble size. Since alcohols are polar they will also form a non-ideal mixture with water. The hydrophobic mineral attaches to the bubble and rises to the froth phase where the valuable mineral is recovered as a concentrate. Frothers have often been characterized using the so-called HLB (hydrophobic-lipophilic balance) number but recently it was shown that the use of activity coefficients (?) or excess Gibbs energy (G ex ), which is calculated using equation (1) is a much more appropriate way to describe the behavior of these reagents in non-ideal mixtures with water (Corin and O’Connor, 2014)."

Jan 1, 2016

By Peter Broad

"Extracting any metal, especially specialty metals and rare earth elements, requires an in-depth analysis of the costs and potential revenue as well as a due diligence study of other stakeholder interests. Rare earth projects are generally in the billion dollar US range or above, and thus failure to accurately predict any loss of revenue caused by impurities within the product or additional effluent treatment costs can destroy an otherwise viable study. Two prime sources of input impurity are considered: impurities in the material feed and from reagents. The effect of these impurities factor on both the product (in reduced revenue) and on residual “tailings” that may incur additional unforeseen costs.INTRODUCTION“Truth passes through three stages. First, it is ridiculed. Second, it is violently opposed. Third, it is accepted as being self-evident” – Arthur SchopenhauerThe era of unscoped, unbudgeted construction ended about 150 years ago. Today’s engineer must design with confidence; but do so amidst proprietary secrets and unfamiliar pollutants, which present a myriad of interesting challenges. Is it possible to build a viable rare earth plant to a realistic budget, without destroying that which we cherish? Some see this as contradictory but in reality it is the only viable option.WHEN GOOD PROJECTS FAILWithout rare earths the Copenhagen agreement might be null and void. Running a wind turbine with a 30 tonne conventional magnet requires some hefty engineering and prohibitive investment. Despite their ‘Green metal’ applications, production of rare earths have created environmental nightmares, as Folger stated in 2011 when visiting Baotou, or has Jaing Mainheng who has been quoted by Ambrose Evans-Pritchard 6 Jan 2013. This comment is not a criticism of China; the details are from a 2012 white paper published by the Chinese Government that initiated a $6 billion environmental clean-up. Nor is China unique; other plants have had problems as well. There were toxic leaks in the 1990s from Mountain Pass, and the Mitsubishi Bukit Merah Plant (built in Malaysia in 1958) required a $100 million clean-up."

Jan 1, 2016

By B. Leonard

As of November 2012, the Alberta government listed 53 oil and gas, oil sands, and mining construction projects either proposed or currently under construction. These industrial plant construction projects have an estimated value greater than 105 million dollars. A common construction method employed for industrial plant projects is fast-track construction, which is used to reduce construction time. Contractors begin fast-track construction with highly generic scheduling information. This high level schedule turns into a lower level schedule as more detailed information becomes available. From a contractor?s perspective, a challenge faced using fast-track construction is the visualization of generic and constantly changing project schedules. This paper discusses the use of a Plant Information Modeling (PIM) system, designed to create a 4D animation to visualize project schedules for fast-track industrial plant construction projects. The proposed PIM system creates a modified project schedule by obtaining specific information from a generic construction schedule. Obtaining the information involves grouping schedule activities in accordance with the level of detail in a 3D model, and the level of detail in a project schedule. The modified project schedule is then used in conjunction with a 3D model to simulate the construction sequence in the form of a 4D animation. This allows for 4D visualization of project activities, installation dates, and crane movements. Furthermore, as engineering reaches completion, the PIM system creates a streamlined channel for schedule information updates to be easily uploaded into the model for a more accurate 4D visualization. Through analyzing a nonmodular construction case study, this paper discusses the successes and benefits of the PIM system for 4D visualization, such as increased productivity, shortened construction time, increased constructability, and decreased field costs.

Aug 1, 2013

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By Mikael Ramström

In 2002 Atlas Copco Rock Drills AB released the new RCS technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging and reduction in manpower in some types and serviceability, have all taken a quantum leap forward when compared with previous generations of drill rigs. The RCS (Rig Control System) is modularised and distributed is accomplished by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions.

May 1, 2003