Search Documents

By D Marshall

The sub-level blasthole benching method of mining has been proved to be economical at Willroy Mines. How-ever due to the nature and attitude of the wall rock, this method is susceptible to serious hanging-wall dilution of the ore. Attempts to solve the dilution problem by various means were not satisfactory until long Stressteel bars were employed as rock bolts. The adoption of this de-vice does not require any special skill, and has become routine in the under-ground operation. Since the inception of this method, the dilution of the ore has been greatly reduced and the ov1!r-all costs of controlling this dilution are much lower. INTRODUCTION T HIS is a report describing the successful use of long Stressteel bars as rock bolts in preventing l1anging-wall failure and consequent dilution in open stopes. Willroy Mines Limited is located (Figure 1) near the town of Manitouwadge, Ontario, approximately l1alf-way between Sault Ste. Marie and Port Arthur.

Jan 1, 1963

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, F. J. Tavitas-Medrano

319-type cast Al-Si-Cu-Mg alloys are commercially important due to their popular use in automotive applications. Artificial aging heat treatments are commonly performed in these alloys to achieve precipitation hardening and, therefore, improve their mechanical properties. The present work was carried out to investigate the effect of conventional (at a constant temperature, as specified by the standard T6 heat treatment regime), and non-conventional multi-temperature and interrupted aging cycles on the hardness, tensile and impact properties of two 319-type alloys (with and without Sr+ Mg additions). The results show that certain multi-temperature aging cycles have a more favourable effect in improving some mechanical properties than conventional cycles.

Jan 1, 2006

By L. Rao, P. Carabin

"Advances in thermal plasma torches have resulted in this technology becoming a commercially viable solution for chemical and metallurgical processes. The main advantages of plasma are its ability to control process chemistry and to build small footprint reactors due to its high energy density and reactivity of the free radicals that are produced. This paper focuses on thermal plasmas produced by DC torches and their applications for waste treatment, production of high purity metals, and nanomaterials. Both transferred and non-transferred torches have been used as either a source of heat or as a reagent in various industrial processes. INTRODUCTIONPlasma technology has become an ideal solution for many industrial chemical, metallurgical and mechanical processes (Venkataramani, 2002). Thermal plasma powered systems are typical used for their unique characteristics such as high energy densities, high temperatures, small installation sizes, rapid startup and shutdown features, controlled process chemistry and use of electrical energy as a heating source resulting in decoupling the heat source from the oxygen flow rate (Heberlein et al., 2007). Depending on the nature of the main plasma forming gas used, thermal plasma systems offer a high temperature heating source coupled with a highly reactive plasma plume rich in free radicals and ions which promote otherwise hard to drive chemical reactions, as well as high heat transfer rates.Industrial plasmas can be broadly classified as thermal plasmas and non thermal plasmas. Thermal plasmas are atmospheric pressure plasmas characterized by local thermodynamic equilibrium (Boulos et al., 1994). Thermal plasmas are typically established between any two current conducting electrodes separated by an insulator. A plasma forming gas is blown between the two conducting electrodes resulting in a high temperature plasma plume. A plasma torch generates and maintains an electrically conducting gas column between the two electrodes; a cathode (negative electrode) and an anode (positive electrode) (Camacho, 1988). If both electrodes are housed in a single housing, resulting in an arc enclosed inside the plasma torch, then such plasma generating torches are termed as non-transferred (NT) plasma torches, whereas, if the second electrode is external to the torch, creating an arc transferred between the cathode and the working piece, then such plasma torches are termed as transferred (T) plasma torches. Depending on the source of the electricity which can be either direct current (DC), alternating current (AC) at main network frequency or at radio frequency (RF), the plasma torches are classified as DC, AC or RF plasma torches (Venkataramani, 2002)."

Jan 1, 2012

By Guoxiang Chi

Hydrocarbon fluid inclusions entrapped in diagenetic minerals may be used to constrain hydrocarbon exploration models in two aspects. First, the distribution of different types of hydrocarbon inclusions in different tectonostratigraphic domains, and their relationships with organic matter maturation levels may reflect a regionalscale variation in the thermal regimes of the hydrocarbon systems. Second, the relative timing of hydrocarbon inclusions in the diagenetic history may provide constraints on the evaluation of reservoir potential. This paper summarizes the distribution of hydrocarbon inclusions in four different Paleozoic tectonostratigraphic domains in eastern Canada, discusses its implications on hydrocarbon systems in the different domains, and finally provides two examples to show how the relative timing of hydrocarbon inclusions may be used in the evaluation of reservoir potential. Oil inclusions mainly occur in host rocks that are within the oil zone, although some are found in units in the condensate zone. Light hydrocarbon inclusions occur in the dry gas zone, and methane inclusions were found from dry gas zone to anchimetamorphism zone. This correlation between hydrocarbon inclusions and host rock maturation implies that the hydrocarbons were derived from source rocks having a maturation level broadly similar to the host rocks. Although the Paleozoic rocks are generally relatively poor in reservoir quality, the two examples provided in this paper show that in some stratigraphic units, significant secondary porosities could have existed prior to some hydrocarbon migration events, thus favoring the accumulation of hydrocarbons.

May 1, 2001

By Michael Loken, April Montera

"The process of blending consistent and predictable feed for the roasters is critical to optimizing product quality and controlling production costs. To assist in this process, Online PGNAA Slurry Analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100% of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their Full Stream, Elemental Slurry Analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced."

Jan 1, 2016

By H. Wotruba, K. Neubert

Dual-energy X-ray transmission (DE-XRT) imaging is known from safety luggage inspections at airports. The use of DE-XRT technology for sorting applications in the primary raw materials industry has been the subject of numerous investigations. Beside other metal ores, X-ray transmission sorting is already used for the preconcentration of tungsten ore, gold ore and coal. The applicability of DE-XRT sorting is limited to ore types where differences in metal concentrations are measurable, based on an interpretation of X-ray images. Metal contents in particles occur in large varieties in terms of concentration, grain sizes, spatial distribution and mineralogy and therefore influence the X-ray absorption. As a result, each ore has to be tested individually for its suitability for DE-XRT sorting. The objective of current research at the Department of Mineral Processing (AMR) at RWTH Aachen University is to assess parameters influencing the detectability of rare earth oxides. Two approaches were followed: (1) Practical test work, based on artificial ore samples of defined compositions and (2) Computer-based simulation of absorption features of identical particle compositions. In total, more than 300 artificial samples of various compositions and metal grades were produced and X-ray images from DE-XRT sorting were analyzed. Results from the DE-XRT sensor were put into correlation with metal grades and particle sizes, to analyze influences and limits on the detectability of rare earth oxides. In addition, a new approach was tested in which the X-ray absorption of particles of various compositions was determined based on a Monte Carlo (MCNP) simulation. During the simulation, similar compositions, as used for the artificial samples, were tested and the X-ray absorption behavior during DE-XRT sorting was determined. A comparison of results from both approaches is used to assess the applicability of the MCNP-simulation for the prediction of the X-ray attenuation behavior during DE-XRT sorting.

Jan 1, 2016

By I. Soosaiprakasam

This work investigated inhibition performance of copper carbonate (CuCO3), which is less toxic than conventional heavy-metal corrosion inhibitors in amine treating plants, The investigation was experimentally carried out in a bench-scale electrochemical corrosion cell under an atmospheric pressure, The inhibition performance of CuCO3 in an aqueous solution of monoethanolamine (MEA) was examined under a wide range of operating conditions and reported as a function of process parameters including inhibitor concentration, temperature and solution velocity, The results show that CuCO3 functions as an anodic inhibitor. The addition of CuCO3 decreases corrosion rate of carbon steel but might induce pitting corrosion/

Jan 1, 2005

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006

By A. M. Martinez, L. Melis, R. C. Peláez, L. G. Garcia

Orovalle Minerals S. L. operates a copper/gold mine in the Asturias region of northern Spain, with the operation dating back to December 1997. The feed to the El Valle mill, consisting of oxide/sulphide (skarn) mineralization, is highly variable, even on a shift by shift basis and presents challenges to the mill operating staff on a daily basis. The mineralogical characteristics of the ore are quite complex with copper present as native copper and sulphides as well as copper minerals with deleterious elements. Gold is present as native gold and electrum. The mill circuit includes SAG/ball mill grinding, gravity recovery of native copper and gold, flotation of copper concentrate, carbon-in-leach gold recovery and SO2/air cyanide destruction. The paper will provide a description of the different unit operations and present operating data of the mill operation.

Jan 1, 2019

By S. Sundararajan, Z. Lin

ABSTRACT Fierce market competition and demand have made it imperative for mining companies to achieve higher productivity and operational efficiency. The selection of the best mining method and equipment combinations will enable companies to meet production and efficiency targets. Continuous mining is increasingly preferred by companies for its high efficiency and low unit costs. We developed simulation models for two continuous mining systems: the continuous surface miner (CSM) system and the at-face slurrying (AFS) system. Considering two different case studies, the paper discusses application of developed models to determine the optimal number of trucks and equipment capacities for the two systems.

Jan 1, 2013

By Z. Zhang

Aluminum boron carbide particulate reinforced composites have found new applications in nuclear industry due to their special capability to capture neutrons, Recently, Alcan successfully developed a liquid metal mixing process to fabricate Al¬B4C metal matrix composite instead of powder metallurgical technology. In the process, titanium is added into the composites to control interactions between boron carbide particulates and aluminum matrix, To understand the effects of titanium on the composites, the solidification microstructure of Al-16%B4C without or with titanium was examined by optical and electron microscopes. The results show that titanium can improve the uniformity of the particulate distribution within aluminum matrix if the titanium content in the composites is more than 0,5%, Furthermore, it is found that the layer with rich titanium on the surface of the particulates can limit the formation of AlB2 type compounds, which may greatly deteriorate the fluidity of the composites, In addition, it is also found that the amount of the reaction products in the composites increases with the increase of holding time. However, the rate of the increase is mitigated by the increase of the content of titanium in the composites. Besides, a procedure was proposed and implemented for the evaluation of uniformity of particulate distribution within aluminum matrix.

Jan 1, 2005

By E. Vesely, A. Saxena

"SAG mill liners are designed for protecting the mill shell and providing lifting power for ore charge and grinding media. Due to the impacts from the charge and the grinding media, the liner experiences dimple, plastic deformation, strain hardening, fatigue, peening and final failure. Because of the collisional environment directly measuring such dynamical loads is extremely difficult if not impossible. In this study we tried to evaluate the liner failure risk by simulating the collisions of solid particles with mill liner using Discrete Element Method (DEM). DEM simulation has been proved to be a very useful tool in evaluation of granular flow and its impacts on the solid structure. But there are certain limits in DEM coherently, such as the number of solid elements, the computer runtime, etc. Here we first present the general feature of the particle-liner collision in terms of impact force and collision energy. Then the effects of parameter selection is discussed. Our simulations show the fatal collisional event of huge impact force is very rare and the collisional events of low impact is much more frequent. The fatal event may contribute most to the liner failure. The rarity of the fatal events may be missed in a short runtime simulation. This technical challenge combined with lacking of criterion to evaluate varying impact loads in fatigue problems may further complicate the evaluation. Should we use the largest impact force alone or we should use the more frequent events is an open question and requires more effort. In order to evaluate the quality of liner design, we proposed a relative comparison method. In the end we show the implication and application of this method in liner optimization by a work example. In particular, the effects of the charge level of grinding balls and their size on the operation performance is presented.INTRODUCTION Grinding is one of the most important and expensive steps of mineral processing. A variety of grinding mills such as rod mills, ball mills, semi-autogenous (SAG) mills and autogenous (AG) mills are being utilized for comminution of mineral ores (Gupta & Yan, 2016). Up to today, SAG mills and AG mills have been widely used to reduce operation costs and increase throughput. In an AG mill, a rotating drum throws larger rocks of ore in a cascading motion which causes impact breakage of larger rocks and compressive grinding of finer particles. Unlike AG mills, SAG mills use steel grinding balls to break ores of size quite small such that they cannot be easily broken in AG mill. SAG mill liners are designed for protecting the mill shell and providing lifting power for ore charge and grinding media. Due to the impacts from the charge and the grinding media, the liner experiences dimple, plastic deformation, strain hardening, fatigue, peening and final failure. Quality and performance of SAG mill liners play a fundamental role to enhance efficiency of grinding mills, because failure of liners is the major cause for unexpected breakdown (Banisi, Hadizadeh, Mahmoudabadi, & Eilkhany, 2006)."

Jan 1, 2019

By R. Hammen, J. Lifton

"The purification of rare earth elements (REE) at mining operations is traditionally accomplished by multiple chemical phase-transfer processes including precipitation, solvent extraction, and ion exchange. We describe REE purification results with Solid Phase Extraction (SPE) columns that were developed to improve the speed and economy of REE purification. The SPE columns have the properties of enhanced equilibration kinetics, so that residence time of a few seconds will accomplish selective chemical transfers from solution phase to solid phase. We describe the separation of REE’s as a class from leach solutions and the further purification of REE salts. INTRODUCTIONHistorically the rare earths were first chemically separated from each other and purified by fractional crystallization. This slow, cumbersome, and laborious process was not suited to commercial production. Solvent Exchange (SX) technology was applied to the problem of separating and purifying the rare earth elements when it was determined in the late 1960s that there might be commercial uses for them individually. At the same time the very slow and expensive technique of ion exchange was applied either for ultra-purification of the desired “light” rare earths, or for the recovery and purification of the tiny amounts of higher atomic numbered, “heavy,” rare earths. Solvent Exchange (SX) has today become the standard for separating the rare earths across their atomic number spectrum. Whereas the separation of the light rare earths commercially may take 30 “cascades’ in a modern Chinese plant, the total separation of all of them from each other may take up to 80 such “cascades,” and is only even “practical’ with preconcentrated feed stocks, such as those produced in China by heap-leaching techniques performed in situ on very low grade radio-nuclide free ionic absorption clays.. Ultra-pure materials of all types are produced today by ion-exchange processing of ionic species already separated by solvent exchange.Hard rock deposits and refractory residues of tin mining and residues from uranium mining have been identified outside of China with very high ratios of dysprosium and other heavy rare earths to the majority lighter ones. Several issues face those who wish to process these materials so as to separate the heavy rare earths commercially:"

Jan 1, 2012

By K. Maruyama, T. Nagasaka, R. d. Chairaksa-Fujimoto, T. Miki

Electric arc furnace dust or EAF dust is considered as a hazardous waste but contains a significant amount of economically attractive non-ferrous metals especially zinc as zinc ferrite (ZnFe2O4) and zincite (ZnO). The hydrometallurgical process is one alternative choice because it has the advantage of low energy consumption. The leaching of ZnO from the dust is very easy. However, the complex major zinc compound in EAF dust is ZnFe2O4, which is very stable and insoluble in alkaline or acidic media under delicate conditions, and causes the low zinc recovery yield by hydrometallurgical process. Moreover, halogens and heavy metals in the dust are also problematic. In order to develop a new effective EAF dust treatment process, the authors have proposed "CaO addition process" as pre-dust treatment to transform all of ZnFe2O4 in the EAF dust to ZnO and Ca2Fe2O5. In this study, the selective zinc leaching from the CaO treated EAF dust with NaOH and NH4Cl solutions was carried out. The effect of temperature, reaction time and solute concentration were systematically investigated. All of zinc in CaO treated EAF dust was successfully leached into both solutions.

Jan 1, 2014

By Julian Boldy

"A review of lI5 significant volcanogenic massive sulphide discoveries in the Canadian Precambrian during the past 65 years reveals that only 7% resulted from surface exploration methods aimed at depths below the effective reach of current geotechnical systems. This has been due to the relative ease of shallow discovery, resulting in the harvesting of ore deposits within 100 m of surface. This surficial layer has been more or less effectively supersaturated by routine exploration. In view of the fact that a mining district's metal content is not likely to be confined to a surficial layer, the time has come to explore the vertical dimension, prospecting for ore at depths in excess of 150 m in productive districts.Essential to this task is an understanding of the Precambrian volcanogenic ore deposit model. The deposits generally have .a tendency to be associated with the terminal phases of felsic volcanism, and to be located along certain time-stratigraphic horizons, marked by the products of volcanic exhalation. The significant massive sulphide deposits are discrete entities, ranging from the top 5% of deposits greater than 45 million tonnes in size, with a surface area of 0.30 km2, to median-sized deposits greater than 1.2 million tonnes in size with a surface area of 0.02 km2. These significant economic ore deposits range in value from $5.5 billion for the top 5% of deposits to $125 million for median-sized deposits. In terms of their frequency of occurrence, the former group has a 4% distribution and the median-sized deposits have a 15% distribution.An historical review of many of the principal Precambrian mining districts, such as Noranda and Flin Flon, shows that major tonnages are usually discovered during the initial phase of application of each new geotechnical search system, until carried to its ultimate limit of effective depth penetration. With the exception of the Noranda district, the mean depth of ore discovery in the other districts is still generally confined to within 50 m of surface.Targeting deep ore is difficult. One effective prospecting method is the detection of fracture-controlled mercury leakage haloes in outcrop (or core) above and peripheral to blind deposits. This technique has proved to be a useful pathfinder, and focuses attention on deposits buried at depths in excess of 700 m in some instances. Down-hole EM systems also promise to be effective in locating deposits previously bypassed by drilling. In addition, trend surface analysis programs of trace element geochemistry should be used as an aid to targeting ore by directing exploratory drilling along the plane of ore-hosting stratigraphy.By definition, mining districts have a proven ""favourability"" for the occurrence of ore. Discovery probabilities in these districts will be considerably enhanced if future search efforts are concentrated below a depth of 150 m, and more use is made of ""deep"" ore search systems coupled with sound geological reasoning. Deep drilling programs to a depth of800 m should initially be designed to search for the top 25% of deposits greater than 3.3 million tonnes in size, with a surface area of0.05 kmt. :a value of$310 million and a 12% frequency of occurrence; This can be accomplished for an over-all cost approximating $40,000 per drill hole. If the search depth is limited to 400 m, the over-all cost of each drill hole is $20,000, equivalent to expenditures routinely allocated to grassroots exploration drilling in the remote greenstone belts of the Precambrian. Depending on a company's objective, prospecting for deep ore offers a stimulating challange - though risky, it has its rewards."

Jan 1, 1981

By R. Minto, W. G. Davenport

The slag removed from the reverberatory furnaces of copper smelters contains significant copper values. A serious financial loss is involved, as further recovery operations are not normally carried out. This paper describes the factors affecting physical transport of matte into slag by gas bubbles, and the subsequent entrapment and flotation of matte drops. Three distinct patterns of transport behaviour have been identified from studies of a number of liquid/liquid systems, including liquid metal and liquid matte systems. A theoretical approach is proposed to explain these behaviour patterns, and to predict transport and entrapment behaviour in matte/slag systems. The concepts of "Film Coefficient" (ø) and "Flotation Coefficient" (?) are introduced. The effects of smelting process variables on the physical loss of copper matte in slag are also discussed.

Jan 1, 1972

By Gabriel G. Walton

Conventional numerical modelling tools for analyses of underground excavations are well suited for modelling elastic behaviour and yield response of geomaterials with very simple constitutive behaviour. Non-dilatant elastic and perfectly plastic behaviour is most commonly used for preliminary analyses in the absence of the data required to consider more complex behaviours such as strainweakening and dilation. For truly brittle models, this deficiency is more acute. Current state of practice allows only for reliable estimation of the volume of failure, but not for any prediction of displacement. In fact, there is no consensus in rock engineering regarding the most accurate approach or most suitable tool to model the magnitude of the plastic deformation that strain-weakening or brittle rocks experience at tunnel boundaries, particularly when support is incorporated into these models. This problem is largely a function of a poor understanding of how inelastic dilation occurs in different types of rockmasses, the rate controls on strength loss and volume change during yield, and the complexities of rock-support interaction in yielding conditions.

Jun 1, 2012

By H. C. M. Gordon

MR. A. D. BADOUX: I have listened to Mr. Gordon's excellent paper with great interest, as I personally have gone through some of the experi­ences he has so clearly depicted. In particular, there were a good many times when we were greatly exercised in our minds as to whether we were justified or not in closing-off certain sections in the Allan mine. The difficulty in these cases arose from the fact that a peculiar smell could be detected in these sections but at the same ti me there was no positive evidence of spontaneous combustion either from heat being apparent or from the possible indications of fire getting any worse. It was suspected that the small percentage of -carbon monoxide that could be obtained by analysis in the air in these sections, and also the peculiar odour, were emanating from the coal itself, and, in order to verify this, bore-holes were drilled in the coal and the gases released from these bore-holes were analyzed. They were found to contain carbon monoxide. After quite a considerable length of time this contained carbon monoxide gradually diminished and finally could not be detected when analyzing such samples of gas. It was our intention to follow this matter up further, as such an occurrence of carbon monoxide is practically unknown, but the sections in which these occurrences were found had to be abandoned. Mr. Gordon referred t0 a case of spontaneous combustion in the Allan . mine, and I may say that, although the section in which that occurrence took place was travelled and carefully examined every day by the colliery officials, yet nothing unusual was noticed until the fire actually took place. This tire was the cause of a slight explosion.

Jan 1, 1938

By Hökmark. H., M. Lönnqvist

"The Swedish Nuclear Fuel and Waste Management Company are planning to construct a permanent storage facility for high-level nuclear waste at about 500 m depth in fractured crystalline rock. One potential concern for the long-term performance of the repository relates to large fracture shear displacements, since these may damage intersected waste containers. Although details in fracture surface geometries are known to influence slip magnitudes and distributions, fractures are commonly approximated as planar features with lab-scale properties due to lack of relevant field-scale data and to limitations in available modelling tools. The purpose of the work described in this paper is to explore the possibilities to use the distinct element code 3DEC to generate and analyze models with isolated, non-planar fractures and, based on the results of such models, get perspectives on the influence of basic disturbances such as ridges, steps and waves. Given the model set-up, fracture segments with orientations deviating from the critical one will contribute to stabilize the fracture. As a result, all analyzed non-planar fractures slip less than the critically oriented planar fracture. We demonstrate that the angle of deviation is the most influential parameter determining the slip magnitude for comparable surface geometries. Similarly inclined steps and ridges have almost equal slip reductions despite differences in surface area restricting the movement. Although it may be possible to translate the influence of such irregularities to an effective coefficient of friction that could be used as input to models with idealized planar fractures, additional analyses with randomly shaped and distributed asperities, different fracture sizes and with alternative stress loads, need to be carried out to devise a defensible strategy for this type of parameter variation. INTRODUCTIONThe Swedish Nuclear Fuel and Waste Management Company’s (SKB) concept for deep geological storage of high-level nuclear waste is the KBS-3 method according to which the waste will be encapsulated in copper canisters and deposited, surrounded by compacted bentonite clay, in vertical deposition holes at about 500 m depth in fractured crystalline rock (SKB 2011). A site has been selected in the Forsmark area, which is located some 120 km north of the Swedish capital Stockholm. One potential concern for the long-term performance of the repository that has been identified by SKB (SKB 2011) is related to large shear displacements along repository host rock fractures induced by a nearby earthquake, since these may cause mechanical damage to intersected waste containers. Due to lack of relevant data at the appropriate field scale and to limitations in available modelling tools, fractures are commonly approximated as planar features with lab-scale properties. The standard numerical tool, 3DEC (Itasca 2013), used in SKB’s rock mechanics analyses, for example, generates planar fractures by default. Results from dynamic 3DEC earthquake-models (Fälth et al. 2010) currently provide input to layout decisions, i.e., the diameter of the smallest planar fractures that must be avoided when deciding on waste container positions at different distances from potential earthquake faults. It is, however, well known that fracture surfaces are rough or undulating on a wide range of scales (e.g., Candela et al. 2012) and that such deviations from planarity influence the mechanical behaviour of the fractures (e.g., Dieterich and Smith 2009, Marshall and Morris 2012, Ritz and Pollard 2012). It will probably never be a realistic option to attempt to represent the geometrical complexity of a population of fractures of different size, shape and surface structure in any large-scale rock mechanical analysis relevant for the performance assessments of the nuclear waste repository. It may however be possible to find approximate ways to represent different styles and degrees of non-planarity by assigning mod"

Jan 1, 2015