Search Documents

"Discrete Fracture Network (DFN) modelling has increasingly being used in many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to provide updated guidelines that address the collection of discontinuity data in the specific context of DFN models. In general terms, the generation of a DFN model requires collecting information on i) fracture orientation, ii) fracture intensity, iii) fracture length and iv) fracture terminations. The International Society of Rock Mechanics (ISRM) suggested methods for the quantitative description of discontinuities in rock masses directly include most of these parameters. However, there are important differences engineers should be aware. To what extent discontinuities can be sampled and which limitations are inherently introduced in the analysis by the sampling methods being adopted represent important aspects that should drive the collection of discontinuity data for DFN analysis; this will require the introduction of a more appropriate set of guidelines bridging the gap between the current, very practical, ISRM methods and the data requirements imposed by the use of new DFN technologies.INTRODUCTIONThe last decade has seen a major increase in use of the Discrete Fracture Network (DFN) approach, both as a stand-alone tool or integrated within more complex geomechanical simulations (Rogers et al., 2014 and Elmo et al., 2014). In particular, the DFN approach offers the opportunity to maximise the use of fracture data collected from mapping of rock exposures and to construct synthetic rock mass (SRM) models. However, the potential of DFN based modelling is limited if there is insufficient care in collecting the necessary structural data at the required engineering scale. DFN models are also subject to the process of data calibration and validation (Hadjigeorgiou, 2012). With DFN modelling becoming an almost integral part of many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to review the process of collecting fracture data in the specific context of DFN modelling.The value of the DFN model depends directly on the quality and quantity of available field data. For example, fracture length (persistence) is an important parameter in DFN modelling; however, this parameter is either seldom available at the pre-feasibility stage due to a lack of exposures (man-made or natural), or engineers have access to limited length data collected along exploratory drifts. Characterisation of rock exposures should also take into account limits of window/scanline mapping techniques with respect to both trace length bias and the effect of cut-off assumptions inherent in the mapping methodology."

Jan 1, 2015

By Bruce Chalmers

INTRODUCTION TIE most important practical problem with which Physical Metallurgy is faced is the control of the mechanical properties of alloys. The most difficult aspect of this problem is the development of new alloys with the properties that are required for meeting exacting engineering requirements. A great measure of success has been achieved by following the empirical method and most, if not all, of the present variety of alloys have been developed by the process of experiment and observation or trial and error. It may, however, be that this method will become. less productive as time goes on, and that eventually it should be replaced by a process based on an understanding of the factors that determine the properties, so that alloys can be 'designed' to meet the requirements. This method of investigation will not be possible until a much better fundamental understanding of metals has been gained, and this will come only about as a result of a great deal of detailed research. The subject of Physical Metallurgy can be divided, as follows, into two parts: we may consider the factors which determine the structure, in the broadest sense, of an alloy. These include the composition and also the treatment to which the material has been subjected. The second aspect is the influence of the structure on the mechanical and other properties. In order to make an effective contribution in this field, it is necessary for an individual or a group to concentrate on a specific and very restricted topic. It is proposed to discuss in some detail the particular subject in which the writer and his colleagues are working.

Jan 1, 1951

By D. Asefi

A new method to detect microstructural features such as recovery and recrystallization as well as cold rolling reduction in low carbon steels was developed based on magnetic hysteresis loop measurement. To this aim, a hysteresis loop measuring apparatus, specifically designed and assembled for plate samples was employed. It is shown that maximum field (Hmax) of hysteresis loop, measured at constant maximum flux density (Bmax) of 0.5T, is an adequatemagnetic property to monitor different stages of changing microstructures during annealing.

Oct 1, 2011

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

By L. Rahnenfuhrer

"Hoisting equipment is a vital part of the operation of most producing mines. Safety and continuation of operation necessitates ultrasonic preventive maintenance inspection on a regular basis.Ultrasonic inspection of hoist shafting, brake linkage and draw bars will contribute to a safe operation and can prevent costly unscheduled shut-down time. With little dismantling, ultrasonic testing techniques can be applied to. determine the conditions of shafting and linkage in hoisting equipment, mining equipment and other miscellaneous mining equipment."

Jan 1, 1969

By R. D. Brown

"When elephants fight, it's the grass that gets trampled". It is becoming increasingly evident that the federal and provincial governments are awakening to the fact that their vigorous scramble for a "fair share" of mineral revenues which kicked off in 1974 has done considerable harm to the Canadian mining industry. Recent public statements made by government officials, particularly at the recently held annual convention of the Prospectors and Developers Association, would indicate that there is a general consensus in the government sector that changes must be made to the mining tax system. However, there is no evidence as yet that there is any agreement among the various governments as to what form these changes should take , who should make them , or when. It would seem to be worthwhile at this time to reflect on where the Canadian mining industry has been vis-a-vis taxes and "where it is at ". This article is based on a recent address given by R. D. Brown, of Price Waterhouse & Co., Toronto, at the annual convention of the American Institute of Mining, Metallurgical and Petroleum Engineers in Denver , Colorado.

Jan 1, 1978

By David J. McDougall

"The production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with Les Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivieres (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about Les Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian milieu, but whatever the reason, the other Quebec iron works have been generally ignored. All but one of the Quebec blast furnaces could be described as ""pre-industrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day. Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence River. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces. Five of these, including Les Forges du St. Maurice, were located on or near the St. Maurice River which enters the St. Lawrence River from the north, and two, the St. Francis Forges and the Grantham Iron works were on or near the St. Francis River which enters the St. Lawrence from the south. In a general way deposits of bog iron ore in the St. Lawrence lowlands of Quebec were contained within the limits of the post-glacial Champlain Sea, with many clustered along the flanks of the St. Narcisse recessional moraine which is crossed by the St. Maurice and other near-by streams, and the Drummondville recessional moraine which is crossed by the St. Francis River."

Jan 1, 1999

By Jochen Petersen

This paper gives an overview of the various strands of postgraduate and undergraduate training offered in the Department of Chemical Engineering at UCT. Since 2003 the Department is offering a formal postgraduate MSc programme in hydrometallurgical engineering aimed especially at graduate work-based engineers, with 5 weeks of intensive course work plus a research dissertation on a work-related project. This programme has now run 5 times over the years and produced some 20 degrees. The paper reflects on the experiences with running the course, especially the difficulties experienced with supervising industry-based external students. Furthermore, through the Department a graduate training program is offered for all junior metallurgists at a major South African minerals company. This 2-year program, which is currently on its 12th cohort, offers 1 or 2 week intensive blocks of course work alternating with longer stints where the candidates are based at various operations. Although primarily focussed on minerals processing, it has a significant element of hydrometallurgy in it and in recent years an advanced hydrometallurgy stream has been introduced. The paper reflects on the development of the program over the years, the benefits it has provided to the company as well as some of the challenges that remain. Finally the paper gives an overview of hydrometallurgy related undergraduate and research-only postgraduate MSc and PhD projects at the university. Some emphasis is placed on the recently launched South African Minerals and Metals Research Initiative (SAMMRI), a joint government-industry programme to support university-based research in the area of applied metallurgy.

Jan 1, 2014

By E. D. Kindle

"The Duthie mine is on the southwest slope of Hudson Bay mountain 7 1/2 miles west of Smithers, British Columbia. A good motor road about 15 miles long connects the mine with the Canadian National railway at Smithers. The principal workings are on the Henderson group of claims between elevations of 3,200 and 4,000 feet above sea-level. Silver, lead, and zinc were produced from this mine between 1924 and 1930.Three adit drifts known as the Compressor, McPherson, and Thompson levels were driven along the Henderson vein-lode in 1922, and the following year the operating company, known as Duthie Mines, Limited, shipped some high-grade silver-lead-zinc ore. Further shipments of high-grade, handsorted ore were made in 1926, and in 1927 a modern flotation-type mill was built, having a capacity of 50 tons of ore a day. Mining operations were suspended in March 1930."

Jan 1, 1954

By Lluís Fontboté, François Lieben, Robert Moritz, Massimo Chiaradia

"Abstract - The Las Cañas stratabound Pb-Zn deposit, in northern Chile, is hosted by the Lower Cretaceous back-arc marine carbonate and subordinate andesitic volcanic and volcaniclastic rocks of the Chañarcillo Group, one hundred meters above a thick pile of magmatic arc-related basaltic to andesitic lavas of the Bandurrias Formation. The deposit is not obviously related to local intrusive rocks, which include an Upper Cretaceous granodiorite batholith and dacite dikes emplaced along normal faults. Stratabound Pb-Zn-Ba mineralization is constrained within several porous stratigraphic units, including a 50 cm thick lapilli-tuff and less well mineralized algal-laminated limestone. Veins that locally carry some Pb-Zn occur along normal faults that displace the stratabound orebodies, and this study shows that they represent a different type of mineralization.Fluid inclusion microthermometric data for ore-stage quartz and barite indicate saline fluids (6 to 30 wt% NaCleq) and a formation temperature in the range of 80°C to 160°C for the stratabound mineralization. Two types of fluid inclusions occur in the veins. The type I vein fluid inclusions indicate less saline (average 7 wt% NaCleq) and slightly higher temperature fluids, in the range of 110°C to 220°C. The type II vein fluid inclusions indicate highly saline fluids (25 to 40 wt% NaCleq) which might be related to minor copper mineralization.206Pb/204Pb, 207Pb/204Pb and 208Pb/204Pb ratios for galenas from the stratabound mineralization, with mean values of 18.42, 15.59, and 38.25, respectively, fall within the range of stratabound polymetallic deposits of northern and central Chile, and indicate a Lower Cretaceous magmatic rock source. Galenas from veins have slightly more radiogenic 206Pb/204Pb, 207Pb/204Pb and 208Pb/204Pb ratios, with mean values of 18.47, 15.61, and 38.34, suggesting two distinct episodes of mineralization.?34S values for galena and barite range from negative values (-31.2‰ to -12.5‰ and -7.7‰ to +12‰, respectively) in the mineralized tuff to higher values in the algal-laminated limestone (-2.5‰ to +1.2‰ and +13.2‰ to +17.4‰, respectively), close to Lower Cretaceous marine sulfate values for barite, and homogeneous values for the galena from veins (-12.0‰ ±1‰). Changing redox conditions can partly account for ?34S variations in the tuff. Sulfur sources include magmatic rock sulfur (-1.5‰ to +9.7‰) as well as sedimentary sulfides and marine sulfate."

Jan 1, 1999

By B. A. Peppley

The current most common method of hydrogen production for fuel cell systems, including SOFC systems, is autothermal reforming. Autothermal reformers have a number of advantages including fast start up and load following and ease of control. However, there are a number of problems inherent with the addition of air into a system connected to the anode feed such as dilution of the fuel with nitrogen and the potential for oxygen to reach the anode chamber directly. Pure steam reforming, which does not involve air addition, provides a richer fuel mixture to the SOFC anode and is inherently safer than autothermal reforming. Although in theory pure steam reforming can be shown to provide these advantages, a number of technical problems need to be overcome before such a system can be practical. In particular, issues such as catalyst degradation due to poisoning and thermal sintering, coking, as well as fuel-steam mixing need to be addressed. Experimental results from a prototype reformer will be presented to illustrate a number of these points. This paper will compare differences in system efficiency, safety and complexity between autothermal/SOFC systems versus a steam reformer/SOFC system. A system simulation will be utilized that is able to account for material and energy balances for a SOFC power generator operating on diesel fuel. The requirements for improved catalysts will be discussed and an analysis of the potential benefits of sulfur tolerance and lower temperature activity will be considered.

Jan 1, 2005

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay's river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By J. Malone, D. Loth, J. Palmer

WMC Resources' Kalgoorlie Nickel Smelter was commissioned in 1972 at a design capacity of 30,000 tpa of contained Nickel in matte. A series of upgrades and progressive improvements have resulted in a design capacity increase to 110,000 tpa of contained Nickel in matte. The smelter sources nickel-in-concentrate from three Mine / Concentrators and supplies nickel-in-matte to WMC's Nickel Refinery and export customers. The Flash Furnace was last rebuilt in 1999, and is over halfway through the 10-year campaign target. The many modifications over the previous campaigns, including the Integrated Flash Furnace, are reviewed. Recent operation of the smelter and the development of the process during the current campaign are detailed herein. An overview of key interfaces with the Nickel Business Unit Concentrators and Refinery operations is provided.

Jan 1, 2005

By J. C. Roy, S. Couture, C. Barbeau

The chemical composition of the asbestos tailings from different mines in the Eastern Townships of Quebec are fairly uniform in composition. The serpentine minerals antigorite and chrysotile form about 85 to 90 per cent of the total. Iron oxides add another 7 to 10 per cent; magnetite represents about 70 per cent of the oxides. Chromite is present in amounts of about 0.5 per cent. The average contents of elemental magnesium, iron and nickel are 23, 6 and 0.25 per cent respectively.

Jan 1, 1972

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size."

Jan 1, 2016

By Y. H. Hatzor, D. Bakun Mazor

"A new model for thermally-induced block displacement in discontinuous rock slopes is being explored inside a Controlled Climate Laboratory (CCL). The model is based on a hypothesized wedging mechanism that takes place inside the filled tension crack of a discrete block that rests on an inclined plane. Irreversible block sliding is assumed to develop in response to climatic thermal fluctuations and consequent contraction and expansion of the sliding block material. While an analytical expression for this model is already available, we are exploring the possibility of obtaining such a permanent, thermallyinduced, rock block displacement, under fully controlled conditions in the laboratory, to enable effective analysis of the sensitivity of the mechanism to geometry, mechanical properties, and temperature fluctuations.A large scale (approximately 0.5 m3 in volume) model consisting of four blocks has been installed in the CCL. The CCL permits accurate control of atmospheric temperature (?0.5 °C) from 6 °C to 45 °C. Harmonic temperature function is planned in advance and is controlled by a computer program throughout the experiment process. The minimum length of the temperature cyclic period for thermally-induced block displacement is calculated here based on the existing analytical model.Due to the fact that this experiment is still in progress, preliminary results will be available in the next few months. The obtained results may explain sudden triggering of rock slope failures that are not correlated with common failure triggers such as seismic activities, pore pressure build-up, or freezing and thawing of water inside rock joints."

Jan 1, 2015

By C. Tan, A. Putz, P. Lacombe, R. Kemp, M. Kaya, B. J. Huls, A. R. Laplante

"This paper concentrates on the four recent plant trials/ applications of froth washing. Results showed that improved metallurgical performance can be achieved with wash water. Increased froth cleaning yielded better upgrading, and some cases slightly improved recovery. Froth sampling and salt tracer tests supported the findings of froth washing tests.At Falconbridge, Ni grade increased from l.47% to 2.15% and recovery from 85% to 87%. At Eastmaque, final Au grade increased from 2.3 to 2.7 oz/st at a slightly higher recovery. At Les Mines Selbaie, Cu grade increased from 24.5% to 25.S% and Zn grade from 54.5% to 56.l%. At Zinc Corp. of America, average Zn grade increased from 55% to 56. 8% at the same recovery for a 45-day period. A number of plants in Canada and the United States have evaluated and/or now practicing froth washing. Wash water has now proved itself in some plants over several months of operation.INTRODUCTIONFroth washing in mechanical flotation cells offers a number of metallurgical (i. e. increased grades and/or recoveries) and economical (i.e. decreased transportation and smelting & refining costs) benefits. Fundamental development work in laboratory and pilot scales performed at McGill yielded encouraging results. (Kaya and Laplante, 1988a and 1989a). Since laboratory and pilot flotation performance can differ from full-scale due to differences in hydrodynamics, kinetics, and froth characteristics (e.g. stability, loading etc.), plant trials were essential to prove the viability of this technology."

Jan 1, 1990

By Y. Hou, E. Arinaitwe, L. Tong

A series of dense medium separation (DMS) tests were performed on four low-grade copper ores from Mount Polley mine in order to determine their amenability to pre-concentration. The tested ores contained disseminated sulphides, mostly chalcopyrite with low copper grades (0.15% - 0.2%) and relatively high iron grades (4.76% - 5.63%). The samples were screened into different size fractions ranging from 9.5 mm to 50.8 mm and DMS tests were performed on each size fraction at various separation densities. The pre-concentration efficiency at different size fractions and separation densities was evaluated in terms of metal upgrading and distribution. Mineralogical tests were also performed on selected DMS sink and float samples in order to understand the influence of mineralogy on the pre-concentration efficiency. The results showed that significant copper upgrading was achieved for intermediate size fractions only at the highest separation density tested. The copper recoveries generally increased with particle size at all separation densities. However, it was impossible to upgrade the copper content in the ores and achieve acceptable recoveries and mass rejections at the same time. Copper recoveries and grades showed a strong correlation with iron recoveries and grades indicating that it is possible to pre-concentrate copper by recovering magnetite and other iron-containing minerals in the ore. Overall, the results suggest that the optimum separation density and pre-concentration efficiency is a function of particle size, and that the ore mineralization properties limit the performance of DMS as a pre-concentration technology for such low-grade disseminated ores.

Jan 1, 2014

By J. W. Keyes

"The original grinding circuit at East Malartic consisted of two 8 by 8 C.A.C. mills in closed circuit with two 72 inch Akins Classifiers and an 8 by 10 secondary mill in closed circuit with two 48 inch duplex classifiers. With this circuit, we experienced a drastic drop in tonnage from one month to another, due to variations in the hardness of the ore. The first step to overcome this difficulty was made by increasing the critical speeds of the mills from 78% to 82%. This resulted in an increase in the secondary mill throughput; but, when the change was made on the primary mills no increase was obtained.The drastic drops in tonnage were still experienced and through working with Allis Chalmers the 8 by 10 mill was converted to a rod mill and the two 8 by 8 n1ills to secondary mills. This change eliminated the two 72 inch Atkins classifiers and the scoops on all the mills, since the 48 inch Akins classifiers sands could then be fed by gravity to the secondary mills through feed pipes.The rod mill and secondary mill discharges were fed to a common pump box using 5 by 5 S.R.L.'s running at 1085 R.P.M. with a twenty-five foot head. When this was done the pumping costs jumped from $105. 00 for 6 months to $1050. 00 in one month, or from 0. 0004 to 2. 75 cents a ton milled. Several factors contributed to this jump in pumping costs as follows:"

Jan 1, 1964

By M. B. McClenaghan

"The Ontario Geological Survey completed a regional till sampling project between 1984 and 1988 in the Black River Matheson (BRiM) area of northeastern Ontario. The project was designed to aid mineral exploration in the area by documenting the Quaternary stratigraphy and by providing a database of till geochemistry. This paper summarizes the results from the sonic overburden drilling component of the BRiM project carried out in areas of thick drift (> 5 m). Results from till sampling in areas of thinner drift (<5 m) have been presented in a separate paper. Approximately 1100 till samples were collected from 225 sonic drill holes. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically and visible gold grains were recovered by panning.Gold and other multielement geochemical data were plotted using proportional symbols to highlight anomalous areas and to demonstrate how to evaluate and interpret a very large geochemical dataset. Thresholds for identifying anomalous concentrations of Au in till samples, defined using the 95th percentile, are 1500 ppb and 12 ppb for the heavy mineral and fine fractions, respectively. The heavy mineral fraction of older ti1ls and to a lesser extent, Matheson Till, display a number of significant gold anomalies in the study area, which in a few cases, are associated with base metal anomalies. The vertical position of gold anomalies in Matheson and older ti1ls varies from directly on bedrock to several meters above the bedrock surface and can provide information of relative ice transport distances."

Jan 1, 1994