Search Documents

By H. C. L. Reemeyer

One of the fundamental trade-offs for copper concentrators is between grinding circuit product size and copper recovery. The capital and operating cost savings and throughput increases for a coarser grind should be evaluated against potential recovery reductions. Other benefits of coarser grinds, such as GHG emissions reductions and favourable effects on tailings and water management should also be considered. This paper assesses the formation of laboratory and pilot test programs, design of process flowsheets, equipment selection, and evaluation methods to determine the most appropriate and economical grind size for a given deposit. The paper will include an evaluation of case studies. INTRODUCTION The majority of the world’s mined copper comes from sulphide deposits, which are mostly processed using crushing, grinding, flotation and dewatering flowsheets to produce copper-bearing concentrates for smelting. Ores must be ground to a sufficiently fine size to achieve an acceptable level of liberation to allow both high recovery of copper and valuable by-product minerals while efficiently rejecting gangue to tailings. Therefore, a key design parameter in process plant design is the grind size of the flotation feed. Copper concentrators use a variety of grind size targets that depend on various factors, including ore mineralogy and the grain sizes of valuable and gangue minerals; the sensitivity of valuable mineral recoveries in the rougher flotation stages to grind size, ore hardness; electricity costs; and mining vs. processing throughput constraints. Typically, copper and by-product recovery increase as grind size is reduced, which can improve revenue, but finer grinds increase power and grinding media operating costs and may have implications for tailings management. This paper explores the trade-offs that should be assessed in determining the optimum grind size, and to answer the question if coarser grinds are worthwhile. METALLURGICAL AND FLOWSHEET FACTORS Recovery-by-size behaviour of sulphide-bearing particles In base metals sulphide flotation, it is typical that flotation recoveries vary by particle size. Metal sulphide particles rendered hydrophobic by collector in intermediate size ranges (e.g. 10 to 100 um) usually show very high recoveries, often approaching 100%. Recovery usually falls away in finer size fractions (<10 um) as fine particles have little inertia and can move around bubbles without colliding and attaching to them. Coarser particles (>100 um) are susceptible to particle-bubble detachment and dropback (Jameson, 2019).

Jan 1, 2019

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By A. E. Reschke

Optimized mine planning of the Leeville Gold Mine, Nevada, necessitated the requirement for an average of 2540 tpd of high quality cemented rockfill (CRF) in primary stoping blocks and underhand cut and fill workings. To meet this requirement, a number of innovative design features were incorporated into the overall batching plant design. Foremost is the use of a dedicated skip to transfer crushed aggregate from surface down through the ventilation shaft to twin underground storage silos. Also, the use of a high shear colloidal mixer on surface to pre-slurry a cement/flyash binder with pipeline delivery to one of two separate underground CRF mixing stations was incorporated. Finally, the binder and aggregate are combined in a 9 m3 twin shaft compulsory type mixer before loading into teleram trucks for placement.

May 1, 2007

By A. E. M. Warner, P. J. Mackey

Copper metal is produced in large or small tonnages in almost all countries of the world—handling raw materials in the form of either as-mined or milled ores, custom concentrates, or other custom materials including scrap and recycled copper. The scale of operations and type of technologies used around the world varies widely. There is a certain concentration of both mining and smelter-refinery production as a total of ten countries produce some 80% of world mined copper, while ten countries—mostly different ones— produce about 80% of smelted and refined copper. As a result, international copper trade is significant. The present paper takes the reader on a virtual tour of the copper plants throughout the world with a focus on smelter facilities. Operations and technology employed at each plant visited are discussed including a brief historical sketch. Future trends identified during the world tour are also discussed. The present authors considered sufficient time was required for a thorough study tour and settled on eighty days—the same as that for the celebrated fictional story of world circumnavigation in the 1870s. INTRODUCTION The celebrated French writer Jules Verne published his book “Around the world in 80 days” in English in1873 and it is the story of Phileas Fogg and his French valet Passepartout circumnavigating the world in 80 days in the fall of 1872 on a £20,000 wager (equivalent to over 2 million pounds today) from the exclusive Reform club in London. This is an interesting period for copper as it started trading on the London metals Exchange in 1876 and the start of global copper production chains started to take off at this time with the rapidly increasing electrification of the world. The production chain includes mining, mineral processing, smelting, refining and fabrication. Since 1880 annual world copper production has increased by over 150 times from 154,000 tonnes in 1880 (nominally considered as smelted copper—essentially the only route at the time to marketable copper) to over 23 million tonnes today (including total refined copper of 19 million tonnes of smelted copper including scrap and 4 million tonnes by solvent extraction-electrowinning), in tandem with increased electricity usage, along with significant transportation usage and for manufactured products (Figure 1).

Jan 1, 2019

By F. P. Hassani, J. F. Boily, A. M. O. Mohamed, M. Hossein

The optimal geochemical parameters required to form ellringite in a lime-remediated site have been investigated with the use of thermodynamic modelling. The speciation of sulphate and 10 metals analyzed in samples of a mine tailing from northern Quebec was calculated with a computer model. The model also includes calcium, which would result from the addition of lime to the system. Two speciation calculations were done. The first one is a hypothetical speciation before the onset of precipitation and was used to devise the stability fields of minerals susceptible of forming in high pHs. The stability fields were determined by building activity ratio diagrams with sulphate, aluminum and calcium species concentrations for pHs ranging from 4 to 14. The investigation was carried out for a 25°C solution with an ionic strength less than 0.12. Thermodynamics predict that an optimal stability field for ettringite in the mine tailing samples containing 10-3 mol/L SO4-2,10-2 mol/L of AI(OH)4 requires at least 10-2mol/L of Ca+2 and a pH larger than 11.6. The sulphate contents of the mine tailing samples, however, limit the precipitation of ettringite and monosulphate could be an end-precipitate. The second speciation is in equilibrium with precipitates and provides information on the speciation of the residual metals. If ellringite could be precipitated as a stable form, it could serve as a sorptive agent for residual metals, and, due to its binding properties, consolidate tailings.

Jan 1, 1995

By I. Mc Dougall, H. Joubert, G. de Villiers

The use of sidewall copper cooling systems to prolong furnace campaign life is becoming an accepted technology solution in the base metals industry. Tenova Pyromet has designed and installed a number of sidewall copper cooling systems in base metals furnaces, including the platinum industry. Apart from increasing the furnace campaign life through the formation of a stable freeze lining, a well-designed copper cooling system enables the plant operator to focus more on optimizing the process to achieve throughput and recovery targets, and to accommodate more varied and available concentrate feed blends. The paper discusses the design of sidewall copper cooling systems for copper smelting and converting furnaces to achieve the above objectives. More specifically, the design of copper cooling systems for top submerged lance furnaces are discussed. An overall increase in furnace heat losses has been raised as a concern for intensively cooled sidewalls. The paper explores the overall heat loss expectations for copper cooled furnaces versus traditional refractory lined furnaces. In addition, the potential use of alternative cooling media is discussed. INTRODUCTION Base metal smelting and converting furnace technologies have been evolving continuously over the past century to satisfy the need for higher throughput, improved efficiency, and longer campaign life. To accommodate these demands, in particular higher smelting intensity and throughput, furnace bath containment systems had to improve. The use of pure refractory lining systems has slowly made room for the use of more intensively cooled lining systems (Joubert, Nikolic, Bakker & Mc Dougall, 2016). These cooling systems evolved from external shell cooling, such as shower or film cooling, to copper plate coolers extending into the furnace refractory lining, and high intensity stave or panel coolers (Verscheure, Kyllo, Filzwieser, Blanpain & Wollants, 2006). Consequently, an increasing number of base metal smelting and converting furnaces are equipped with copper cooling systems, including flash furnaces (Bryk, Ryselin, Honkasalo, & Malmstrom, 1958; Yasuda, Motomura & Kawasaki, 2014; Marx, Shapiro & Henning, 2010), top submerged lance primary smelting and fuming furnaces (Bhappu, Larson & Tunis, 1994; Kim, Lee & Lee, 2000; MacRae & Steinborn, 2018), top submerged lance converting furnaces (Viviers & Hines, 2005; Nikolic, Hogg & Voigt, 2018), primary platinum smelting electric furnaces (Nelson, Stober, Ndlovu, De Villiers & Wanblad, 2005; Jones, 2005; Hundermark, De Villiers & Ndlovu, 2006; Mc Dougall, 2013), and electric slag cleaning furnaces (Joubert, Nourse, Masters & Hundermark, 2005).

Jan 1, 2019

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

By S. V. Burr

"IntroductionOne of the more puzzling geological enigmas, in the writer&apos;s opinion, is how rock can move sideways with respect to other rock. In the writer&apos;s study of regional northwest-southeast folding in North America (Burr, 1980), he may have found the answer to horizontal offset.Horizontal OffsetSideways movement or horizontal offset does not mean that the movement was, or is, horizontal. As indicated below, the actual movement may be at a high angle from the horizontal. However, it is the horizontal VECTOR, or offset, which is measured on surface by geologists. Vertical movements (thrust, normal, reverse) can be understood, as they involve blocks of rock , generally separated on four to six sides, which have been pushed up or subsided. Vertical faulting across dipping strata can produce APPARENT horizontal offsets. However, this thesis deals only with ACTUAL offsets.The ProblemFigure 1 is a plan view of a simple hypothetical horizontal offset. Three vertical dykes are intersected by a fault lineament. Two dykes exhibit no movement; the middle dyke has been offset a distance (a). Vertical faulting would have produced no horizontal offset. How can a horizontal distance (a) disappear or appear? Rock expands or contracts in infinitesimal amounts.SolutionThe map (Burr, 1980) shows the writer&apos;s interpretation of regional northwest-trending folds in Ontario. The writer made two observations about horizontal offsets during his thirty year study of these folds:1) All major horizontal fault lineaments strike at a high angle to the northwest fold axes. Many of the northwest-trending lineaments are fault s, but their movement is essentially vertical.2) Close to many of the known horizontal offsets (and several lineaments), there are areas where plunge reversals are so frequent and close together it is impossible to draw in all the fold axes at a scale of 1 inch = 4 miles, and, in the highly faulted Espanola area southwest of Sudbury, Ontario, all the indicated folds cannot be easily separated at a scale of 1 inch = 1 mile. The writer has observed folds less than 30 feet apart next to the strong Puskitamica-Chibougamau fault in northern Quebec."

Jan 1, 1982

By E. Wusaty

"Fording Coal is a wholly owned subsidiary of Canadian Pacific Limited. The company was founded in 1968 to mine metallurgical coalfor export at the Fording River operations in southeast British Columbia.Today, Fording Coal Limited also operates the Whitewood mine under contract to TransAlta Utilities and the Genesee mine under a joint venture arrangement with Edmonton Power. Both these operations are located just west of Edmonton and produce subbituminous low-sulphur coal which is used for power generation. Fording also owns and operates two industrial mineral mines in the United States and is mining overburden under a lo-year contract with Syncrude Canada at Fort McMurray.As of December 1992, Fording Coal Limited owns and operates the Greenhills mine which was closed due to bankruptcy. This papers deals with the innovations and changes which have been made and those which are currently being implemented to make this operation competitive in the world export coal market. IntroductionOn December 4, 1992, following a tendering process, Fording Coal was awarded 80% controlling interest in the Greenhills mine by Trustee Arthur Andersen Inc. Assets acquired included 100010 of the land and coal leases and 80% of the major joint venture assets including all structures. The remaining 20% is owned by Pohang Steel Canada Ltd., a wholly owned subsidiary of Pohang Iron Steel Co. of Korea. The Greenhills mine had been in continuous operation since 1983 and was finally closed due to bankruptcy of its majority owner on October 31, 1992.A permit to operate the Greenhills mine was issued by the British Columbia government on January 29, 1993, and Fording Coal Limited started mining operations in late February 1993.To return the Greenhills mine to profitability significant changes were required in workforce productivity, mining methods and equipment selection. These mine plan changes are designed to make the Greenhills operation competitive in world markets, provide longterm employment for the company&apos;s workforce and ensure that a secure supply of coal is available."

Jan 1, 1994

By J. Mirza, E. Nicol, J. Lipkowski

Gold passivation in thiosulfate leaching media is a major barrier to its implementation. Addition of Cu (II) into the leaching solution has shown to aid in gold dissolution, but the mechanism by which it acts, and its role in the passive layer, remains unknown. Surface Enhanced Raman Spectroscopy (SERS), in tandem with linear sweep voltammetry, were employed to determine the dependence of leaching currents on mass transport and for fingerprint identification of sulfur species on the surface of gold. SERS leaching experiments were performed using gold nanorod electrodes that showed increased stability compared to other SERS active surfaces.

Jan 1, 2011

By F. Mallozzi

"With the requirements of air pollution codes becoming more and more critical, the role of the ventilation engineer in industry has become an extremely important one. The ventilation engineer must provide the expertise for the selection of equipment and the design of systems which will reduce pollution to an acceptable level. Because pollution control systems involve considerable capital and operating expense, he must have the ability to select, from a wide range of products, the collector which will provide the required performance with a minimum of down time for maintenance. This paper discusses the principles of wet collection and the forces used to separate particulate matter from a gas stream. Important factors in the selection of equipment, such as collection efficiency, horsepower requirements and water consumption for the various types of collectors, are discussed in detail, as well as the construction features normally incorporated to circumvent potential problems."

Jan 1, 1971

By Paul Stothart

Context ? Industry is active in urban, rural, and remote regions ? Faces a range of environmental challenges and ?social license? issues ? There are also Aboriginal and northern issues ? Also very active internationally, with associated challenges ? Environmental/social groups often target the industry ? The important contribution of the industry should not be overlooked Useful Minerals and Metals Minerals are intrinsic to the residential, municipal, communications, and transportation infrastructure of modern life. Examples: Hybrid motors - nickel hydride batteries Water purification systems ? nickel, rare earth elements Catalytic converters - cerium Screens and monitors - several rare earth elements Clean electricity - uranium Circuitry - gold, copper, aluminium, lithium, titanium, silver, cobalt, zinc Instruments - copper, silver, nickel, cobalt, copper, brass Protective products ? zinc, calcium carbonate, sulphur

May 1, 2008

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Thorium is frequently the main radioactive element in rare earth ores and is a resource that can potentially substitute for uranium. Thorium must be separated from rare earths in order to obtain products with low radioactivity. There are abundant resources of thorium in the rare earth ores in China, especially in Baiyunebo mixed ores. As an associated element coexisting in rare earth ores, thorium is, or can be, separated from rare earth concentrate, iron concentrate, as well as from waste water and slag to achieve recovery of thorium. The methods of separation include ion exchange resin, liquid-liquid extraction, and liquid-solid extraction. TBP extraction has been the main method applied to separate thorium by domestic and foreign scholars. This paper presents a comparison of different processes for the separation of thorium from rare earth ores, especially Baiyunebo mixed ores, single bastnaesite and monazite ore, and provides suggestions for the future recovery of thorium resources.

Jan 1, 2014

By G. E. Agar, W. B. Kipkie

"This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady state balance can be calculated for a circuit.Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative tec1nique to arrive at the steady state balance. The program is written so that a variety of circuits can readily be simulated.A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets is presented on sulfide ores, on copper-nickel separation and on silver flotation,"

Jan 1, 1978

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By Ken Woloschuk

??Owners?Perspective ??Owners?Challenges ??EcoNomics?Delivery Model ??Projects ??Project Outcomes ??Questions ??Balancing the triple bottom line initiative: ?shareholders expectations of economic costs and benefit; ?stakeholders expectations of social and environmental costs and benefits; ?deciding what is sustainable and which design alternatives are the most sustainable. ?? Delivering required project outcomes

May 1, 2008

By Paivi Suikkanen, Kari Hietala, Kaarlo Haavanlammi

"Processing of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of platinum group metals (PGM’s) and cobalt are key issues of the Nickel Smelting technologies. PGMs are typically found in association with each other, but also importantly with nickel and copper. A challenge of producing saleable concentrates at acceptable recovery degrees, an increasing focus on the sustainable use of metals and recent decreases in the value of nickel has increased the interest to find a reliable route from Cu-Ni-PGM bulk concentrates to product. According to studies, most efficient process for Ni-Cu-PGM concentrates is flash smelting using DON process20 years ago, in 1995, Outokumpu commenced at Harjavalta a new Nickel Flash Smelting technology based on the Direct Outotec Nickel (DON) Smelting Process. The DON process enables production of high-grade nickel matte with low Fe-content directly in the Flash Smelting Furnace (FSF) without subsequent converting. Metal values from the smelting slag are recovered in the Electric Furnace (EF) as iron containing Ni-matte. Matte refining is based on atmospheric pre-leaching and total pressure leaching. Nickel, cobalt and iron are leached leaving a leach residue containing small amount of gangue minerals and PGM’s. Iron is removed from the leach solution in and nickel will be recovered with standard methods. Overall > 95% metal recovery can be expected with low energy consumption and low environmental impact."

Jan 1, 2014