Search Documents

By Daiki Takano, Naoki Takahashi, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"The method in this study, in which cement-treated piles are installed into the ground to decrease the amount of liquefied lateral flow, has been studied. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. In their investigation, they propose shifting the position of the piles to prevent lateral flow in various directions. The present study conducted centrifuge model tests to clarify the improvement effect of piles against the lateral flow of liquefied soil and the effect of the pile arrangement. Then, numerical fluid analyses were conducted to consider the improvement mechanism. As a result, the model tests and numerical analyses showed that the pile improvement dramatically reduced the lateral displacement and that the average total flow velocity decreased in the irregular case.INTRODUCTIONLiquefied ground subjected to seismic motion loses its stiffness and strength, and lateral flow often occurs in sloping areas and backfill areas behind collapsed quay walls. In the Hyogoken–Nanbu Earthquake in 1995, the reclaimed island that was surrounded by collapsed quay walls expanded toward the sea and the amount of displacement reached a few metres (Hamada et al., 1996). Two countermeasures can be considered to guard against lateral flow: preventing liquefaction and reducing lateral displacement. The former method is ideal; however it is costly and time-consuming. Based on these considerations, the authors (Takahashi et al., 2013; Morikawa et al., 2014) are currently studying a method in which cement-treated piles are installed into the ground (see Fig. 1) to decrease the amount of liquefied lateral flow. The countermeasure cost using this method is relatively low because of the low replacement ratio. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. It has been proposed that the position of the piles should be shifted so that lateral flow can be prevented in various directions, as described in Fig. 2."

Jan 1, 2015

By Gerry Houlahan

The east span of the 3.5 km long SF-Oakland Bay Bridge is supported by different types of foundations along its span. Starting from the west, its first 460 m section comprising twin concrete box-girders is supported by sands and rock on Yerba Buena Island. A 620 m long steel suspension span then bridges a 25 m deep channel that is formed in sediments overlying rock. Twin concrete box girder structures, each 2.4 km long, complete the stretch over the remainder of San Francisco Bay to the engineered earth fill landing at its east end. For most of its length, the Skyway bridges water 3 to 10 m deep over soft surficial Young Bay Mud. The foundation types include spread footings with hold-downs, steel and concrete piles that are set in drilled rock sockets up to 3 m in diameter and 2.5 m diameter steel tubular piles driven to penetrations of up to 100 m. The design and construction-related considerations are presented. The different foundation types, influences of the site geology and earthquake demands on the substructures are discussed. The seismic motions of the bridge superstructures and substructures, as well as the depth-varying soil motions, influenced the foundation design. Together with performance-based design criteria, including post-earthquake footing displacement limits, these seismic demands influenced various aspects of the foundation design, including the use of battered and vertical piles.

Jan 1, 2013

By Eric Rehwoldt, Walt Rabe, Jesús Gómez, Tim Myers

"An expansion plan for Washington Dulles International Airport is currently underway to prepare for growth at this northern Virginia facility in the future. While Dulles currently serves more than 20 million passengers a year, when the Master Plan for the Airport is fulfilled, it will be capable of handling approximately 55 million passengers a year. The current Capital Construction Program underway at Dulles will take the Airport one step closer to its full potential.As planned, work includes a new Airport Traffic Control Tower, expansion to existing concourses, a fourth runway, additional parking, and other improvements. One of the most interesting features of this project is the construction of a two-track passenger train system (Automated People Mover, or APM) linking the main terminal and concourses, which will largely replace the Mobile Lounge transportation system, thus greatly reducing surface traffic. Construction of the APM system involves deep excavations along the tunnels and at the transfer stations. This poses special challenges because the settlement-sensitive terminal, original Airport Traffic Control Tower, and concourse buildings, as well as other facilities, exist near the proposed below-ground stations. The site is also underlain by a tight grid of underground utilities that include jet fuel, gas and central communication lines, in addition to more mundane electric, sewer and water mains.One of the most interesting features of this project was the extensive and skillful utilization of micropiles for support of existing structures adjacent to the excavations. Without the use of micropiles, the cost and difficulty of the excavations would likely have been much more. Several important lessons were learned about the use of micropiles, which advance that technology.Throughout the project site, bedrock was generally encountered at 25-ft depths or more. The rock consists of micaceous and highly calcareous siltstone rock. This rock is typical of the sedimentary component of the Culpeper Basin, a Triassic Age geologic feature extending from south central Virginia to western Maryland. The siltstone beds dip gently to the west at about 10 to 20 degrees. Joint planes typically dip 60 degrees to vertical. The rock underlies a sequence of fill materials and residual soils of varying thickness."

Jan 1, 2009

By P. M. Deshpande

An interactive short column system is evolved as alternative to deep foundation system in deep layers of marine clay, the interaction of encased stone column and marine clay carry load without causing conventional settlement. This paper presents concept of the system and its field application as foundation of culverts on marine clay layer of 15 to 17 M underlain by residual soil layer of 5 to 6 M, where conventional pile of 23 to 25 M would have been required.

Jan 1, 1996

By P. Middendorp, Gerald E. H. Verbeek

"INTRODUCTIONStatic Load Testing (SLT) is generally considered the pile testing method that provides the de-facto answers regarding pile capacity and load-deflection behavior. However, as this testing method is time consuming and costly, alternative pile testing methods are applied, such as High-Strain Dynamic Testing (HSDT), commonly referred to as Dynamic Load Testing (DLT), and Rapid Load Testing (RLT), which includes Statnamic Testing (STN) and the Fundex Pile Load Tester (PLT). Extensive descriptions of these pile testing methods as well as comparisons of the results from these two methods have been widely published, but little is written on the choice between HSDT and RLT. This article will address this issue for concrete piles by discussing five different aspects that should be considered when making a choice between HSDT and RLT for either cast-in-situ piles or precast driven piles. TIMINGThe timing of the pile load test is independent of the testing method. For cast-in-situ piles load testing is performed some time after the pile has been installed (to allow the pile to obtain the compressive strength required to withstand the test load), while for precast driven piles load testing is performed after a so-called set-up period following pile installation (to allow the soil to recover from driving induced disturbances and, at least in most cases,regain strength).In other words, the timing of the test does not affect the choice of the testing method.ACCURACY OF THE APPLIED LOADWhen a pile is tested by RLT the applied load is measured by a calibrated load cell placed on the pile head, just as it would be during SLT. This means that the error in the applied load value is less than 0.1% of the maximum range of the load cell.However, when a pile is tested by HSDT the load is calculated from the measured strains, which means that the outcome is dependent on the pile material properties. In this case the applied load (F) on the pile head is calculated by multiplying the measured strain (?) with either the calculated or estimated elastic modulus of concrete (E) and the pile cross section (A).The elastic modulus is generally back calculated from the (average) stress wave velocity (c), which in turn is derived from the reflection time (T) it takes for a stress wave to travel over the pile length (L) from the pile head to the pile toe and back to the pile head."

Jan 1, 2006

By Krishnendu Mandal

"For a multi-story building project in Kolkata, a pile load testing program was conducted to minimize pile performance uncertainty resulting from variable subsurface conditions and to verify the pile load vs. settlement response. The program consisted of performing five (5) instrumented load tests on augured cast-in-place (ACIP) pre-production test piles. Vibrating-wire strain gages and extensometers were installed in the test piles at strategic locations to enable measurements of the load vs. deformation behavior of the test piles. This paper presents a description of site subsurface conditions, test pile installation, instrumentation setup for a maintained load test (MLT), static compression pile load test results, and pile instrumentation result interpretation. Average mobilized unit shaft resistance values are calculated.2.0 INTRODUCTIONThe project site is located in Kolkata, near river Ganges, and the proposed development plans consist of constructing six (6)25-story (G+25) towers; see Fig. 1 and Fig. 2 below for approximate site location and proposed development layout, respectively. The buildings were designed to be supported on ACIP piles. A field load test program was implemented to verify sub-surface conditions and pile design. The test program consisted of installing Five (5) instrumented test piles numbered LP1A and B through LP6A and B, and performing static compression load tests on these piles. The piles were instrumented with vibrating-wire strain gauges and extensometers, so that the pile shaft resistance distribution along pile length and the pile toe resistance could be interpreted using direct instrumentation measurements."

Jan 1, 2015

By Hennie F. T. Barnard

Where geotechnical designs are governed by settlement requirements, soil and rock moduli are important parameters for design. This paper reports on a method that was used to utilize dynamic modulus measurements in the field toward pile settlement designs for the proposed Square Kilometer Array (SKA) Project to be located near Carnarvon, South Africa. The project will comprise of over 3000 No. movement sensitive satellite dish structures. The method described in the paper utilizes strain-related modulus degradation across the complete ground profile, starting from measurements of peak particle velocity (and inference to dynamic modulus at small strain) as measured using Continuous Surface Wave (CSW) testing at individual dish positions. This is required due to the very small allowable foundation rotation of 5 arc seconds under the dishes? operational conditions. The strategy of analysis was to conduct an iterative process starting from the measured small strain modulus profile of the ground. The likely maximum pile force for a specific piled foundation option was estimated and a single pile finite element analysis was performed using Plaxis 2D (Version 2010) to estimate the expected ground strain developing along the length of the pile. By assuming the shape of the shear modulus degradation curve with increasing shear strain, the iteration process then converged on a likely degraded modulus profile associated with the single pile and maximum load assumed. This process enabled identifying the pile cap size, pile configuration, pile sizes and pile lengths that would meet the operational movement limits. The chosen pile group configuration was then analyzed using the Repute 1.5 pile group analysis software. The design process and typical results are discussed in this paper.

By Hennie F. T. Barnard, Theodore E. B. Vorster

Where geotechnical designs are governed by settlement requirements, soil and rock moduli are important parameters for design. This paper reports on a method that was used to utilize dynamic modulus measurements in the field toward pile settlement designs for the proposed Square Kilometer Array (SKA) Project to be located near Carnarvon, South Africa. The project will comprise of over 3000 No. movement sensitive satellite dish structures. The method described in the paper utilizes strain-related modulus degradation across the complete ground profile, starting from measurements of peak particle velocity (and inference to dynamic modulus at small strain) as measured using Continuous Surface Wave (CSW) testing at individual dish positions. This is required due to the very small allowable foundation rotation of 5 arc seconds under the dishes’ operational conditions. The strategy of analysis was to conduct an iterative process starting from the measured small strain modulus profile of the ground. The likely maximum pile force for a specific piled foundation option was estimated and a single pile finite element analysis was performed using Plaxis 2D (Version 2010) to estimate the expected ground strain developing along the length of the pile. By assuming the shape of the shear modulus degradation curve with increasing shear strain, the iteration process then converged on a likely degraded modulus profile associated with the single pile and maximum load assumed. This process enabled identifying the pile cap size, pile configuration, pile sizes and pile lengths that would meet the operational movement limits. The chosen pile group configuration was then analyzed using the Repute 1.5 pile group analysis software. The design process and typical results are discussed in this paper.

Jan 1, 2017

This paper summarizes seven years of Italian ex­perience with the use of large calibration chambers for the calibration, under closely controlled stress and strain conditions, of some in situ testing devices which are used in sand deposits. At the present time two calibration chambers are operating in Italy, one at E.N.E.L.-C.R.I.S. (Milan) (*) and the other at I.S.M.E.S. (Berga­mo) (**). Both chambers can accomodate cylindrical samples 1.2 m in diameter and 1.5 m in height. A detailed description of these chambers can be found in Bellotti, et. al (1982).

Jan 1, 1987

By Raymond Henn

Yes we have also used some however, again because of the nature of the maintenance window where we have that two hour (at best) window every night and due to the numerous other crews that are wanting to get in to do the other types of maintenance activities, we don't know if we are going to be getting into that same area from one night to the next. So even with the dormancy additives that one can add to cementitious grouts (that are good up to 72 hours) we don't know if we are going to get back in to the same locations from one week to the next. That's why I use the term "the forgiving nature of the acrylamide". It allows us to ream out the hole allowing us to use the exact same hole without having to re-drill a new hole. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. Up to the end of 2001 we were just over 1.7 million liters of between AV100 and AV118 grout. Of that, approximately just under 200,000 was AV100 and the remaining balance was AV118.

Feb 10, 2003

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale.Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and refl ective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become fi lled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale. Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and reflective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become filled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007

By Matthew Janes

The installation of piles and casings is becoming increasingly difficult as restrictions on vibration become common in major urban areas. The use of high frequency, resonant excitation of a pile or casing permits ease of installation of sections to great depths with near imperceptible vibrations as close as 1 pile diameter. The new Resonant Driver is able to excite a pile at its resonant frequency (up to 150 Hz or 9000 VPM) to produce elevated levels of acceleration, force and displacement in the pile. The combination of extremely high acceleration and controlled levels of displacement allow the pile to slice through varied soil with almost no vibration translated into the ground. In direct comparisons between conventional vibrators and impact hammers the Resonant Driver produces less than 1/50th the vibration. The Resonant Driver results in ground vibration of between 1/20 and 1/40 of common limit levels (1 cm/s or 0.5 in/sec) as close as 1 pile diameter. At a distance of 5 m (16 ft) from the pile or casing vibration levels approach imperceptible levels. The Resonant Driver uses a proprietary algorithm to tune the drive vibration to the changing natural frequency of the pile as it is driven into the ground. By maintaining resonance the energy in the pile is built up like in a flywheel on an engine or a child on a swing. This build up of energy aids in driving and significantly reduces waste. Recent experience using the Resonant Driver is proving the technology can drive a variety of steel pile and casing sections through varied soils. Continued use of the Resonant Driver will create a data base of various pile and casing sections, soil types and achieved capacities.

Jan 1, 2008

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano, Shinya Tachibana

"The helical piling system provides solution to many geotechnical related problems due to its quick installation, higher compressive and pullout resistance, no wastage of material, workable in limited areas and reusability. However, its use as a foundation for bridges and high-rise buildings is still limited as compared to other piling methods. In the present study, the performance and load settlement behavior of screw and straight pile is investigated under cyclic compressive load in dense ground conditions. To achieve the set objectives, pile load tests were conducted in a cylindrical steel container. The model ground was compacted with dry sand at relative density of 80%. It is observed from the test results that screw and straight pile resistance reduced when the cyclic load is applied at allowable pile resistance state. The reduction in the ultimate pile capacity is more in straight pile than in screw pile. However, straight pile showed higher ultimate pile capacity than screw pile under similar pile tip diameter. The effect of helix bending deflection on load settlement behavior and ultimate pile capacity increases under cyclic loading.INTRODUCTIONScrew pile is one of the new developments in deep foundation, which is growing tremendously fast because of its quick installation technique, less noisy operation, no wastage of material and involvement of minimum manpower. Screw piles have an edge on straight pipe piles due to its high bearing capacity and uplift resistance. The installation mechanism of screw pile is different from straight pile. Torque and pressure is required to install the screw pile whereas hammering, pressure and vibration is required to install straight pile. As the installation mechanism is different between screw and straight pile, therefore, the ground disturbance that is produced during their installation is also different. The ground disturbance produced during the installation also depends upon the pile tip condition i.e. open or closed ended. Sakr, (2009) stated that the compressive capacity of screw pile in 3 to 5 times higher than driven piles having the same shaft diameter and length. The reason for this increase in pile capacity is due to helix, which is generally 2 to 2.5 times the pile shaft diameter. Larger helices can give higher end bearing capacity but it requires very powerful machinery to install in dense grounds. For instance, if large helix screw pile is installed in a dense ground then helix-bending deflection will start affecting the end bearing capacity (Yttrup and Abramsson, 2003; Malik et al. 2013 and 2015). According to Malik (2015), the equations of thin plate (Young and Budynas, 2002) with uniformly distributed load on the plate can give reasonable estimation of helix deflection due to dense ground conditions."

Jan 1, 2016

By Zia Zafir

"Levees in the central valley of California are primarily for flood control purposes and thus are subjected to infrequent hydraulic loading. The primary concern for these levees is their instability due to through and under seepage. Primary seepage control measures are seepage cutoff walls and/or seepage berms. The cutoff walls primarily consist of soil-bentonite (SB) slurry walls. The seepage berm could be a drainage blanket to allow the seepage with controlled exit gradient or an impervious layer to provide enough cover to protect any adverse effects of seepage in terms of sand boils. Although, Sacramento is an area of moderate seismic activity, levees protecting urban areas require assessment for the potential instability due to liquefaction and associated vertical and lateral deformations. In certain cases, the seismic deformations of the levee may not compromise the stability of the levees, but they may cause damage to the seepage control measures. Depending on the nature and extent of the damage, the mitigation measures may require limited or full replacement of the seepage control measures. This paper will provide a systematic assessment of these different types of seepage control measures under vertical and lateral deformations due to liquefaction and lateral spreading under seismic loadings.INTRODUCTIONThere are two broad categories of levees in Central California: levees that are subjected to continuous hydraulic loading such as delta levees and are called frequently loaded levees (FLL) and flood control levees that are subjected to seasonal or infrequent hydraulic loading, called infrequently loaded levees (ILL). This paper will focus on the seismic response of ILL. The probability of ILL experiencing an earthquake at the time of the design flood is very low. Therefore, consequences of seismic failure of flood control levees are only significant in terms of response time required to restore the level of flood protection provided by the levee before the next flood season. An example for this restoration is the restoration of the Pajaro River levees in Santa Cruz, California after the 1989 Loma Prieta Earthquake. Nevertheless, failure of flood control levees due to a seismic event could result in loss of the entire levee and/or loss of freeboard. In addition, some of the seismic failure of ILL levees may result in loss of seepage control measures such as the soil-bentonite wall.The State of California State approved Senate Bill (SB) 5 in 2007 that mandates for 200-year flood protection to be the minimum level of protection for urban and urbanizing areas in Central California (Sacramento-San Joaquin Valley) by the year 2025. This legislation also requires that urban and urbanizing areas protected by Federal project levees cannot use adequate progress as a condition to approve development after 2025. SB 5 requires that the urban level of flood protection be consistent with criteria used or developed by DWR (Government Code § 65007(k)). To avoid delaying urgently needed flood protection, Urban Levee Design Criteria (ULDC, 2012) was developed."

Jan 1, 2016

By James W. Niehoff

"Prior to 2003, most high rise structures in Honolulu, Hawaii were supported on driven pile foundations, extending through shallow coral strata and bearing in competent formations at depths of 100 ft (30 m) or greater. In 2003, the 40-story Hokua Tower became the first building in Hawaii to use continuous flight auger (CFA) piles for support. These piles derived most of their capacity from side shear in the shallow coral formations, which reduced their required lengths to less than 100 ft (30 m) sand significantly increased their capacity. Not only did CFA piles prove to be more efficient and cost-effective than driven piles, but the reduced noise and vibration associated with their installation made them and drilled piers the foundations of choice for most mid- to high-rise projects going forward. Because drilled foundations were new to Hawaii, it was necessary to develop effective design parameters for the unique soil and rock conditions found within this urban area. While drilled foundations were found to have many advantages over driven piles, construction techniques had to be modified to compensate for extensive voids in the coral formations. This paper presents a compendium of the data derived from numerous full scale, instrumented load tests conducted during the past decade and provides guidance for the design and installation of CFA and drilled pier foundation systems in areas having geologic settings and history similar to that of Honolulu.INTRODUCTIONThe State of Hawaii is one of the most remote areas in the world, lying nearly 2400 miles (3800 km) from the nearest continental land mass. In spite of this vast distance, the population of the islands has grown to over 1 million people, the majority of whom live within and in close proximity to the City of Honolulu on the Island of Oahu. The city is densely populated with over 400 high rise apartments, condominiums, hotels and office buildings located within 5 miles (8 km) of the city center (Fig.1). Nearly all of these buildings have been constructed within the past 50 years."

Jan 1, 2016

By Jamey Rosen

A Project Information Management System (PIMS) was developed to manage and analyze QC data at the Herbert Hoover Dike Rehabilitation Dam Modification Cutoff Wall (owned by the Jacksonville District of the United States Army Corps of Engineers). A special feature of this PIMS was its geospatial component. Data collected from Bauer drill rigs were automatically “geoprocessed” into threedimensional features representing the predrill, jet grout, and Cutter Soil Mixing panel elements, as well as calculated verticality and overlap metrics. These features were visualized in interactive planimetric, profile, and 3D views that facilitated several quality control activities during the project.

By Andrew Higgins, Jamey Rosen

This presentation will demonstrate some recent advancements in the applications of Project Information Systems (PIMS) technology to seepage barrier walls in the context of evolving Owner Specifications. The use of geospatial technology in particular is used to track, visualize, and analyze data from a variety of sources and serve those data to contractors and owners via dashboards and as-built drawings. Data describing the geometry of construction elements (including diaphragm panels, secant piles, and jet grout columns) is of particular importance on these projects, and this presentation will include case studies in the United States of how these data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage).

May 1, 2022

By Damien Enright, Franz-Werner Gerressen

CFA/ACIP pile is the most used single pass drilling method for deep foundation installations. It is constructed by rotating and driving a Continuous Flight Auger (CFA) into the ground at a controlled speed to the specified pile depth. Concrete is then pumped under continuous positive pressure through the hollow stem of the auger to fill the borehole as the auger is withdrawn. CFA/ACIP piles are preferred due to their high daily production capacity when used in suitable soil conditions. CFA/ACIP piles have been installed in the United States for decades and the industry has seen a huge development in equipment, installation process, monitoring and more. Nowadays, CFA/ACIP piles are installed using fully computer monitored drill rigs rather than a bulky crane and lead setup. Because of the torque and crowd offered by these rigs, piles can be installed to depths of more than 100 feet and diameters up to 48 inches. New age crane-based equipment with leader systems are than welcome to substitute old fashioned bulky cranes These new age crane-based systems combine the benefits of sufficient hydraulic power, fully equipped software, etc. with the additional benefits that they can do single pass drilling without extension systems, even when drill depths of more than 100 feet are required. The paper will explain the construction process and will discuss some jobsite references and experiences made using the new age crane-based equipment.

Oct 1, 2022

By George Burnhart

"Sonic drilling is a relatively new technology even though it has been in development since the late 1940s. It was initially funded by the U.S. petroleum industry and then, in the late 40s, Russian scientists worked on developing sonic drilling, their interest based on drilling rates 3 to 20 times that of conventional methods. In the early 1960s, the Shell Oil Company backed research that resulted in a down-hole device with a series of eccentric weights driven by drilling fluid to generate vibration. Hawker Sidley, in the early 1980s, developed the first modern prototype sonic drills in Vancouver B.C. and the North Star Drilling Company in Minnesota became the first contractor in the U.S. to operate sonic equipment in 1985. In 1994, North Star became a division of Boart Longyear, headquartered in Salt Lake City, Utah.What’s Unique about a Sonic DrillA sonic drill rig appears and operates very much like any conventional top-drive rotary rig. The key difference is that a sonic drill has a specially designed hydraulically powered drill head, containing oscillators, that generates adjustable high-frequency vibratory forces. The sonic head is attached directly to the drill pipe or outer casing, sending the high frequency vibrations down through the drill steel to the face of the drill bit. This creates displacement, fracturing or shearing action depending on the material being drilled. The oscillator uses two eccentric, counter-rotating balance weights or rollers that are timed to direct 100% of the vibration at 0 degrees and 180 degrees. An air spring houses the oscillators and separates the vibration from the drill rig itself. The vibratory frequency is controlled to suit operating conditions and to achieve optimum drilling rates.When the vibrations coincide with the natural resonant frequency of the steel drill rod or casing, a natural phenomenon called “resonance” occurs. It allows the rig to transfer timed vibratory energy into the top of the drill string, utilizing the natural stored energy of the steel. This causes the drill string to use inertia and act like a flywheel delivering tremendous amounts of energy directly to the bit face. In friendly overburden formations, a sonic drill rig can achieve penetration rates of one ft per second."

Jan 1, 2008