Search Documents

By Charles Roeder, Amy Leland, Dawn E. Lehman

Concrete filled steel tubes (CFSTs) are composite members that are commonly used in many countries today. CFST components are used in the United States, but they are more common in Asia, in part because the connections used in Asia are quite labor intensive and there are not standard connections in the U.S. In addition, US design specifications are prepared by separate groups for structural steel and reinforced concrete structures and so composite systems that use CFST components are not overseen by a single group and as such there are several, conflicting design standards. In the US, steel tubes used for CFST are more slender (i.e., the diameter-to-thickness, D/t, ratio is larger) than some other countries, and labor practices (structural steel labor is different than reinforcing steel labor) also cause potential conflicts in construction. As a result, CFST has had some use in tall building construction in the US, but very limited use in bridge construction. A research program at the University of Washington has been in progress to address many of these issues with an eye towards universal design expressions, simpler, standardized connections and promotion of accelerated bridge construction (ABC). The research has resulted in recent changes to the American Association of State Highway Officials (AASHTO) bridge design specification as well as state departments of transportation (DOTs), which supports the increased use of CFST in bridge pile and drilled-shaft foundations. An experimental research study which investigate the flexural strength, shear strength and connections was conducted. These connections provide good performance under both seismic and gravity loads and address the concerns of US construction. These connections, their design rules and requirements, and their impact on composite behavior and system performance are discussed. These results permit rapid and economical construction of CFST bridge piers, piles and drilled shaft foundations. They encourage the use of more slender and economical tubes, while achieving the benefits of composite construction. INTRODUCTION Concrete filled steel tubes (CFSTs) are widely used for bridge and building construction in Asia, but the use of CFST in bridge construction is limited in the US. The historical use of structural steel and reinforced concrete in US bridge construction have resulted in more developed design expression for those construction methods, which has limited the use of CFST. Bridge construction in the US is inherently different than in Asia because of differences in codes, labor costs and construction practices. As a consequence, design and construction practices that are economical and practical in other countries may not be practical for US bridge construction.

Jan 1, 2019

By Adrian M. Keller

Borehole televiewers are downhole inspection devices available for high-resolution imaging of a borehole wall following rock coring. Borehole televiewers should be considered by geotechnical engineers and geologists as a supplemental way of investigating rock for deep foundations. The optical televiewer (OTV) produces a digital optical image and the acoustic televiewer (ATV) utilizes reflected acoustic waves to produce images of the borehole walls. These devices can be utilized to examine soft or fractured zones in the rock mass, solution features, open joints or other voids not observable from traditional rock coring techniques. These devices along with computer post-processing can determine the strike and dip of joints, bedding planes, shear surfaces, or other structural features, eliminating the need for expensive oriented cores or manned downhole logging. An acoustic televiewer was utilized in the Fall of 2008 during the investigation phase for the I-70 New Mississippi River Bridge (I-70 MRB) in St. Louis, Missouri. Voids and fractures in the upper portion of the rock were described by prior consultants. Further investigation of these features was necessary to evaluate deep foundation options to support the main towers. Ten borings were drilled from a barge in the river at the two main tower pier locations. An ATV was utilized in each of the ten borings to produce images of the rock mass in the borehole and allow further investigation of the voids. Voids interpreted as solution features were readily identified in the ATV logs in multiple borings and at similar elevations, suggesting connectivity. Measurements of the voids? width, location in the borehole and orientation allowed a more thorough understanding of the potential impact the solution features may have on the planned deep foundations. An extensive grouting program was eliminated based on the ATV results.

Jan 1, 2010

By Brian T. Nereson, Michael C. Penney

"This technical paper was prepared to describe the general process by which the authors designed a column-supported load transfer platform (LTP) for support of asphalt-paved runway and taxiway embankment areas over soft organic soils, the major tasks and observations made during construction of the system, and the outcome of the system design and construction. The LTP system was designed using the method described in the BSI Standards Publication Code of Practice for Strengthened/Reinforced Soils and Other Fills, BS 8006-1:2010 (BS8006), to achieve performance objectives for the project. The design also used other criteria based upon the authors’ engineering experience and understanding of the expected interaction between soils, structures and geotextiles. The design and construction process described herein resulted in a successful project. The authors identified that full-time engineering oversight during construction was of high importance and provided a high degree of value to the project. The authors’ intimate knowledge of the potentially adverse effects of variations in construction practices promoted timely identification of construction deficiencies that could have affected the reliability of the system. This resulted in corrections and modifications being made, while materials were still accessible, to protect the intended performance of the finished system.INTRODUCTIONThe site is located in Marshfield, Massachusetts. The surrounding area is flat and contains significant wetlands with a water table at or near the ground surface. Prior to the improvements described herein, the site was already developed as an existing municipal airport with an approximately 3,000 linear-feet asphalt-paved runway oriented in a northeast/southwest direction (northeast end referred to as Runway 24 and southwest end referred to as Runway 6; Fig. 1). The site is located approximately 0.5 to 1 mile (Runway 24 and Runway 6, respectively) from the Atlantic Ocean.The improvement project included total extension of approximately 550 linear feet of asphalt-paved runways and taxiways over existing wetlands that consisted of soft, organic soils with varying but significant depths (Fig. 2). An initial geotechnical assessment performed for the project identified that the subsurface conditions were not suitable to support the proposed runways and taxiways in their existing state."

Jan 1, 2016

By Stefan Dahlin

The laboratory tests indicated low permeability but as I said, as a rule, the permeability in the field has been found to be higher. A high permeability has also been found when doing back calculations of rates of settlements in different cases. But as I also said, there's a need for further studies in this area.

Feb 10, 2003

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015

By I. D. Dayal, Anil Kumar Jain

"Cutoff walls are frequently used to slow down or prevent seepage of water through and/or around dams. Cutoff wall is a type of seepage barrier structure designed to reduce the flow of water underneath temporary or main dam. There are number of techniques for the construction of cutoff walls including concrete, Jet grouting and permeation grouting. NHPC LTD, a premier Govt. of India undertaking has been instrumental in the hydropower development within the country & in nearby countries like Nepal & Bhutan since last four decades. NHPC LTD has completed more than 20 hydro-electric projects with total installed capacity of 6587MW (including capacity addition by JV- NHDC). In all these projects, different types of dams and spillways were constructed in not so benign to extreme challenging geological set up. There has always been challenge associated with the temporary diversion works. The project sites sometimes incur huge river bed excavations in case of concrete gravity dam founded on rock foundation at large depth. The challenges for minimizing the seepage have been well taken care by constructing the dedicated seepage barriers. The construction of cut-off walls have progressed from “conventional continuous trench backfilled with conventional concrete or plastic concrete” to “grout curtain”, to “jet grouting” to the “concrete cut-off wall” , the last being the most sophisticated & credible seepage barrier.The efficiency of the cut-off walls are monitored by the seepage quantity observed (reduction of the seepage flow), uplift pressures or exit gradients after construction of cut-off walls. For construction of the main concrete dam, required space is created by the river bed excavation for placing the dam foundation on sound rock. Sometimes there is deep river bed excavation from 30 to 40 m depth or even more as per the available rock profile. Temporary coffer dams are constructed for diverting the river flow through diversion tunnels / channels etc. In deep river bed excavation; there are high chances of the significant seepage through the coffer dam foundation / river bed material due to high hydraulic gradients. Seepage and piping are the main causes of the failure / damage of the temporary coffer dams. If the seepage quantity is too high, then it becomes difficult to handle it by dewatering in the dam pit. Dam concrete is required to be placed unhindered to have a monolithic construction of dam blocks & to have faster construction in the working season. Cut-off walls increase the seepage path considerably thus reducing the exit gradient and further reduction of the seepage thus helping in maintaining the seepage free area for working."

Jan 1, 2016

By Richard Hanke, Franz-Werner Gerressen

"The twin decked Alaskan Way Viaduct is a passage to Seattle’s downtown waterfront and of great economic importance to the city. In 2001, the Nisqually earthquake damaged the viaduct and led to the redevelopment of this corridor. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. State-of-the-Art special foundation equipment was mobilized for the project to perform a broad range of geotechnical construction. Applications included soil mixing and jet grouting for confinement cells around new bridge foundations, large diameter secant pile walls for the Tunnel Boring Machine launch portal along with an extensive jet grouting regime for ground improvements within the tunnel alignment. This paper will study the evolution and use of advanced special geotechnical construction equipment and describe its application at the Alaskan Way Viaduct Replacement Project.INTRODUCTIONThe evolution of geotechnical construction equipment continues through innovative applications and continued modification or enhancement of machinery. Similarly and in parallel, market expectations continually demand more in terms of construction speed and performance. Together, market demands and contractor innovation have led way to the development of specialty geotechnical construction equipment with capabilities previously not seen feasible or possible. Several examples of this scenario have recently developed during design and construction of the Alaskan Way Viaduct Replacement Project.The Alaskan Way Viaduct Replacement Project is a joint project between the Federal Highway Administration (FHWA), the Washington State Department of Transportation (WSDOT), and the City of Seattle. Three build alternatives were under consideration for replacing the Alaskan Way Viaduct: the Bored Tunnel Alternative, the Cut-and-Cover Tunnel Alternative, and the Elevated Structure Alternative. Ultimately, the bored tunnel option was selected as the best value approach. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. Several other associated improvements tie into this project that will ultimately lead to the complete demolition of the viaduct and redevelopment of Seattle’s waterfront."

Jan 1, 2015

By Shigenori Horikawa, Nobutaka Tanaka, Toshiro Hara, Kengo Yamamoto

"The CDM-LODIC method(Low Displacement and Control method), a modified the CDM(Cement Deep Mixing) method, reduces the ground displacement through the removal of in-situ soil equivalent to the amount of slurry injection using the continuous auger flight attached on the shaft above the conventional the CDM mixing tool. The reduction of ground displacement minimizes the impact on adjacent buildings and other infrastructures. Since the development of the CDM-LODIC in 1985, this method has been used for more than 900 projects with total volume of improved soils exceeding 5.3 million yd3 (7 million m3). The ground displacement that could be caused by deep soil mixing is controlled by balancing the volume of discharged soil and the volume of slurry injected for soil mixing. This paper presents the ground improvement work for the Sanriku Coast Expressway Project using the CDM-LODIC method to 1) control the ground displacement during ground improvement to minimize the impact to existing buildings and facilities and 2) utilize low height CDM-LODIC equipment to avoid potential damage to critical facilities in the vicinity of ground improvement area and avoid interference on the normal operation of the Ishinomaki Red Cross Hospital.INTRODUCTIONSanriku Coast Expressway is a reconstructed highway, which is part of an early restoration program to recover from the Eastern Japan Earthquake of March 11, 2011. This highway extends 223 mile (359 km) and connects the Pacific Coast regions of three prefecture of North Eastern Japan as shown in Figure 1. Along a section between Yamoto - Ishinomaki road, the highway was expanded from two lanes to four lanes to mitigate traffic congestion for the adjacent city center and hospital and to serve as an efficient transportation route for emergency or disaster relief needs as shown in Figure 2. Deep mixing ground improvement with an area replacement ratio of 50% was designed to provide settlement control under the new fill embankment of the expanded highway as shown in Figure 3. The original CDM treatment layout using 5.2ft (1.6 m) diameter columns is shown in Figure 4."

Jan 1, 2015

By KeerthiRaaj Subrmanian, Muthukkumaran Kasinathan

"A railway embankment is under construction between Nagapattinam to Thiruthuraipoondi covering 36.5 km. The sub-soil strata comprises of soft clay extending up to 10 m below existing ground level, which is subjected to stability and settlement problems. A trial stretch covering about 5 kilometer was improved using Prefabricated Vertical Drains (PVD) with surcharge was recommended to accelerate the consolidation settlement. The geotechnical characteristics of the subsoil are examined through laboratory tests on representative soil samples. Recent improvement in the finite element analysis has facilitated modeling of PVD in finite element software for computing the settlement magnitude and time rate of consolidation. In this study the theoretically predicted settlement magnitude and time rate of consolidation from Terzaghi.s vertical consolidation, Barron's radial consolidation are compared with the analyzed FEM results for both the cases with and without PVD improved embankment. The comparative analysis between FEM and predicted data hold good for stresses and the associated deformations. The excess pore water pressure was significantly lower and their dissipation was faster in case of embankment with vertical drains. Thus PLAXIS 2D tool shows fairly convincing results in comparison to the theoretical solutions.1. INTRODUCTIONFrom the earlier times civilization has been developed in a fashion either at the banks of river or near to the shore region, because of the easier availability of food and water. This over centuries made them as huge cities, consequently population rise made the increased necessity of highway, railways, port and even more ground for construction. As a stake researchers are pushed to make a low bearing ground into a massive carrier of skyscrapers, embankment, bridges etc. These low bearing ground suffers from total and differential settlement, slope instability. Hence, numerous ground improvement techniques were followed to eradicate these concerns which include preloading, piling, stone column, vertical drains and geosynthetic reinforcement. Among them Prefabricated vertical drain (PVD) are often used to accelerate consolidation of soft subsoil and has been the main soil improvement method used in improving the soft marine clay deposit (Chu et al.(2004); Chai (2001) and Arulrajah et al.(2003)). Literature review of embankment over soft clay deposit reveals that combination of PVD with preloading is widely considered as an economical and less time consuming ground improvement technique."

Jan 1, 2015

By Morris J. D, Baldwin Z., Wiltcher P. M

21 Moorfields is an oversite development in central London spanning Moorgate tube station. It required the installation of both the highest loaded bearing piles and the highest top loaded static pile test ever undertaken in the UK, at 50.5MN (5,680 tons). The 17-storey building is founded on only 15 large diameter bored piles installed through the roof of the live station. The piles are located in two parallel rows 50 m (164 ft) apart, bridging the underlying train lines and the Crossrail tunnel below. This unique project required a diverse cross-section of skills and experience from the Project Team as we not only pushed the boundaries of design but also those of construction practices. Our team therefore needed to be made up of members from multiple businesses and disciplines. The team worked together, in a highly collaborative environment, for around two years before any work started on site. A key challenge for this project was that there was only one opportunity to construct each pile. If a position had to be abandoned there were no alternative locations and the impact on the project would have been catastrophic. It was therefore vital that all events that may have led to the abandonment of a pile were investigated ahead of commencement on site. Risk elimination and mitigation strategies were developed for all eventualities whether they be associated with the design or construction processes. The successful pile load test, coupled with all contract piles being fully instrumented with state-of-theart fiber optic (CemOptic) cable along their full length, has improved our understanding of the performance of such large and heavily loaded piles. The works piles will all be monitored during the construction of the new building, providing new insight into their real-world performance. Such groundbreaking work has never been undertaken before in the UK and has the potential to significantly influence the industry’s understanding of pile behavior, and design, in the future. This paper will discuss the challenges the team encountered during the design and construction of this highly complex urban project, particularly when adopting, by necessity, a pioneering approach.

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Peter Deming

"PART 1 OF 2INTRODUCTIONSlurry trenches are the least cost hydraulic barrier available, if the excavated spoils can be recycled into backfill. As such, slurry trenches are constructed where possible, sometimes at high risk. Slurry trenches are also used to install biopolymer drainage trenches, which have a low safety factor because the biopolymer slurry weight is marginally greater than the weight of water. In marginal ground the construction risk falls to both the Owner who designs and asks for the construction, and the Contractor who manages the work and promises to complete the project successfully. This paper discusses design and construction of slurry trench barriers in marginally stable ground and where groundwater chemistry invokes the need for slurry management details to obtain proper backfill placement.As a designer, Mueser Rutledge Consulting Engineers works for both Owners and Contractors. We are usually able to convince Owners of their responsibility for design detailing in order to obtain a working final product and to obtain reasonable bids from Contractors by disclosing construction needs and designing to reduce the contractor’s exposure. We often work for Contractors to produce designs which result in successful construction in projects where the Owner’s engineer places the responsibility of design and construction on the Contractor.This paper is intended to inform both Owner and Contractor audiences of resources which are available to reduce the risks of trench collapse in difficult ground conditions. We hope it serves this purpose.DESIGNSubsurface InvestigationsSubsurface conditions should be defined by borings focused on definition of the soil profile and soil design parameters. After general subsurface conditions are defined, barrier borings should be drilled along the final alignment.Definition of Soil Strength and CompactnessCompactness of sand and gravel strata should be defined with Standard Penetration Test N-values. The shear strength of cohesive materials should be defined by laboratory testing. Silt and fine sand strata with little cohesion should be investigated using mud rotary techniques to prevent disturbance. General strength characterization by soil layer should be used for analysis of trench wall stability."

Jan 1, 2006

By Ørjan Nerland, Torgeir Haugen, Astri Eggen, Kjell Karlsrud

"Ground improvement by the deep dry mixing (DDM) method is used in Norway since the late 1970's. A brief review is given of the Norwegian guideline for ground improvement with DDM issued in 2012, but focus is on practical examples and experiences related to improving the stability of excavations and natural slopes in soft clays. Two examples deal with experiences from 10 to 18 m deep excavations in soft and partly highly sensitive clays, where DDM panels and block stabilization were used to both give sufficient stability against bottom heave and to limit lateral wall displacements. A third case deals with improving the stability of a natural slope in quick clay by installing DDM panels near the crest of the slope. To limit disturbance and excess pore pressures generated during the DDM works, vertical drains were installed in advance in between the DDM panels. This ensured that the excess pore pressures generated by the DDM works (up to 150 kPA) dissipated quickly, which was instrumental to avoid triggering a landslide during the stabilizing works.INTRODUCTIONThe lime column (LC) method developed in Sweden and Japan in the mid 1970's (e.g. Broms and Boman, 1977). Since then, there have been significant developments in Scandinavia and around the world in terms of rigs, mixing machinery and tools, and type of binders used. The method, presently named the ""Dry Deep Mixing"" (DDM) method in contrast to the wet deep mixing methods (WDM) that also have developed significantly over the past decades, e.g. Kitazume and Terashi (2013). The first application of the DDM method in Norway was in the late 1970's to improve the stability of an excavation in quick-clay, then using only lime as binder. Most DDM applications in Norway have also thereafter been to improve the stability of cuts, supported excavations or natural slopes in soft clays. The Norwegian Geotechnical Society (2012) issued in 2012 “Guidelines for design of ground improvement with DDM methods"". The following highlights design issues dealt with. The paper focuses however, on some practical cases where DDM has been used to improve stability of deep excavations and a natural slope in soft and partly highly sensitive clays."

Jan 1, 2015

By Osvaldo Valdez, Matteo Bertoni, Aem Ragy

The East St. Louis Deep Cutoff Wall project is located in the area of East St. Louis, Illinois, across the Mississippi River from the city of St. Louis, Missouri, along the left descending bank of the river. The project is a fundamental part of the U.S. Army Corps of Engineers' (USACE) effort to rehabilitate and secure the aging East St. Louis levee system that provides flood protection to approxi- mately 250,000 residents and more than $4.5 billion in economic value. The project was devised and de- signed by USACE as a cutoff wall to be installed in the Metro East Sanitary District levee segment, one of the levee segments that form the East St. Louis system. The contract for the construc- tion of the cutoff wall was awarded in November 2019 to Bauer Foundation, the American subsidiary of the Bauer Group.

Sep 1, 2023

By Takefumi Takuma, Masashi Nagano, Koji Kajino

As part of the construction of a multi-span pre-stressed concrete girder bridge for Japan’s new high speed rail line, landslide preventive piles were installed on the flank of a steep slope. The rotary pressin piling method was selected to install three parallel rows of long (up to 36m, i.e., 118ft) and large diameter (1,200mm, i.e., 47.2in) pipe piles safely into the slope as a deterrent measure. They were spaced at 2.5 Dia (3.0m, i.e., 9.8ft) on center and were staggered to allow the groundwater to migrate between the piles. Each pile had a sacrificial cutting shoe welded at its toe for speedy installation and was rotated and simultaneously pressed into soil on the slope through the stable bedrock thereunder to achieve a robust landslide prevention in a relatively short period of time.

By Khamis Y. Haramy

Curing temperature, density, and moisture significantly affect the velocity measured in the crosshole sonic logging, the rate of strength gain, and the final strength of concrete in drilled shafts and, thereby, affect their structure capacities. Non-destructive field measurements can enhance the QA/QC program by measuring temperature, density, moisture, and sonic velocity of curing concrete during the construction and curing of drilled shafts. The curing environment can greatly affect the concrete strength, and requires close attention during construction. This article shares the experience with the NDE technology used in the QA/QC program in the drilled shaft construction. To understand the mechanism by which a drilled shaft cures under field conditions, two newly constructed drilled shafts were monitored for up to seven days, immediately following concrete placement using the following geophysical logging methods: a) temperature logging; b) crosshole sonic logging; c) gamma-gamma density logging; and d) neutron-moisture logging. One additional drilled shaft was also monitored to a shorter duration. Temperatures were monitored using the sensor in access tubes and/or thermocouples embedded at the center of a drilled shaft and near its reinforcing cage. For a small shaft under 1m diameter, curing temperatures appeared to peak at 41° ? 68° C at different depths at around 24-hour curing time and decreased to and stabilized at around 23° ? 35° C in 6 days. The shaft curing rate varied with depth, shaft diameter, surrounding geo-material types, and the depth of ground water. CSL logging was performed in one shaft from top to bottom from six access tubes and limited monitoring in another shaft. The velocity increased with curing time till 4 to 7 days, and, at a specific time, the velocity appeared to be inversely correlated to curing temperatures. The gamma-gamma density log (GDL) results from 5 different depths were obtained at a source-detector separation of 355 mm. The average density was found to increase with curing time, but decrease slightly in 3 to 5 days. At a given time the GDL density curves seemed to correlate with the neutron monitoring logging (NML) moisture curve. The NML moisture was monitored from 1st to 6th day after concrete placement. The moisture was highest when surrounded by bedrock, then clay, and sand due to different hydration rates.

Jan 1, 2007

By Hubert Law, Amin Rahmani

This paper evaluates the effects of pile diameter on the initial modulus of subgrade reaction and proposes modifications to the subgrade reaction moduli that are commonly used in the current state of practice based on American Petroleum Institute (API) guidelines. Three-dimensional continuum finite element model of a soil-pile system is simulated under monotonic lateral loadings to develop benchmark data. The benchmark data, which includes small (0.5 ft) to large (10 ft) diameter pile responses, is used to estimate the initial modulus of subgrade reaction for each of the considered pile sizes. The study shows that the subgrade reaction moduli provided by API may underestimate the actual soil stiffness at the soil-pile interface for large diameter piles and may overestimate it for piles smaller than a certain diameter. A simple equation is proposed herein to adequately estimate the initial modulus of subgrade reaction for all pile diameter ranges. The proposed equation is validated by the measurements of full-scale field tests.

By Paul R. Lear

Sustainability continues to be an important aspect of remediation and infrastructure projects. Deep soil mixing (DSM), a common construction and remedial technology, can easily incorporate the following sustainability best management practices (BMPs), including Minimizing Total Energy Use and Maximizing Use of Renewable Energy; Minimizing Air Pollutants and Greenhouse Gas (GHG) Emissions and Maximizing Use of Machinery Equipped with Advanced Emission; Minimizing Water Use and Impacts to Water Resources; Beneficial Reuse of Materials/Reduction of Materials and Waste Reduction; Use of Local Labor and Supplies. This paper focuses on the sustainability of DSM treatment and provide carbon footprint calculations at least one completed DSM project which used these sustainability BMPs to demonstrate the environmental impact of the sustainability.

Sep 8, 2021

By George Burke

"Many soil mixing methods have evolved over the years, but the Trench Cutting Re-mixing Deep method (TRD) was developed in Japan, circa 1993, to construct continuous uniform cutoff walls, without the need for an open trench. TRD mixing has been used on over 300 projects in Japan for excavation support, groundwater barriers, liquefaction mitigation, soil improvement and pollution containment. To date, TRD mixing has been used on only three projects in the United States: a test cell in Long Beach, Calif., for seawater intrusion barrier in 2004; a groundwater barrier at a wastewater treatment plant in Lincoln, Calif., in 2005; and presently at Herbert Hoover Dike surrounding Lake Okeechobee in southeastern Florida.The most notable benefits of TRD are its abilities to overcome difficult geology, such as layered rock and dense cobbles and gravels that hinder other soil mixing methods, and to create extremely high-quality walls. The method is ideal for situations in which access precludes the use of more traditional methods due to spoil control, such as waterways and congested urban environments or subsurface obstruction/difficult ground. Spoil disposal is minimized since TRD mixes the soil in place.TRD mixing has a horizontal continuity advantage over traditional multi-auger deep soil mixing (DSM) systems. Because DSM systems create walls by overlapping soil-cement columns, the auger may be deflected by difficult ground, and gaps are possible. Gaps may also occur when constructing an exceptionally deep wall due to the possibility of auger deviation from its required vertical alignment.The method also has a homogeneity advantage in layered soils. Because DSM constructs columns by rotating the defined length mixing tools up and down the soil profile while injecting binder, strength and permeability in each layer will vary. The TRD method vertically mixes the entire profile and core samples show highly uniform strength. It is most cost-effective in deep difficult ground such as layered rock or dense cobbles and gravels."

Jan 1, 2009

By G. Stuart Littlejohn

In spite of recent concerns in certain European countries, I believe that silicate-ester grouts will continue to be employed in practice, unless more cost-effective inorganic grouts are developed for the treatment of fine sands. It is also noteworthy that over the past 40 years, there has been a record of good experience where silicate-ester grouts have been used in ground improvement. Nevertheless, there is now a need via the European Standard EN 12715 (2000) "to assess the environmental impact, particularly the toxicity of the grout and grout components, and their effect on ground and drinking water should be considered before grouting." "When testing the grouting material for environmental impact, the following aspects should be considered: ? Whether during processing, transport or grouting, substance can be generated or released which could be hazardous to the environment or the grouting crew; ? Whether noxious substances can spread upon mixing with ground water; ? Whether reaction products can be produced or released which influence the water quality; ? The type of particles eroded from hardened grout; ? Chemical reactions between hardened grout and the ground water."

Feb 10, 2003