Search Documents

By David S. Cronan

Submarine hydrothermal mineralization occurs in at least three locations along the Hellenic Volcanic Arc in the Eastern Mediterranean Sea. Weak hydrothermal discharges occur off Kos and Nisseros at the eastern end of the arc and off Milos at the western end. In both cases the hydrothermal solutions are rich in iron and manganese and are precipitating iron oxides variably enriched in minor elements. This points to the likely presence of sulphide minerals at shallow depth below the sea floor at these locations. By contrast, at Santorini, in the centre of the arc, the hydrothermal discharges are much stronger and rate of deposition of the hydrothermal minerals much greater. Indeed, in one of the two hydrothermally active embayments off Santorini (Nea Kameni) hydrothermal deposits are accumulating up to five times as fast as in the Atlantis II Deep of the Red Sea. Radiocarbon dating indicates that these deposits have been accumulating for about 100 years. In the other embayment off Santorini (Palaea Kameni), hydrothermal deposition has taken place over a longer period (more than 1,000 years) but the deposits are not so hydrothermally enriched due to the simultaneous deposition of biogenic silica and detrital mineral with the hydrothermal deposits. The observed pattern of increasing intensity of submarine hydrother¬mal activity from the extremities of the arc towards its centre argues for additional hydrothermal mineralization on poorly explored areas of the sea floor between Milos and Santorini and between Kos and Santorini.

Jan 1, 1994

By Seung-Kyu Son

Environmental properties of the northeast Equatorial Pacific along 131.5 degrees west, between 5 degrees and 13 degrees north latitude, were investigated in association with changes in water column structures during the summer seasons of 1998 and 1999. Climatic disturbances such as El Nino and La Nina, should have affected this area during the study period. In 1998, a thermocline where temperatures rapidly decrease with depth, was formed at 90~110 m water depth. However, in 1999, a very fluctuating thermocline was observed with latitudes. As a result of changes in the water column structures, biological and chemical environment also showed fluctuation parallel to the changes in other physical parameters. Inorganic nutrient depleting areas, especially for nitrate+nitrite and phosphate, or oligotrophic regions were extended down to approximately 100 m depth, which coincided with the surface mixed layer depth. In the euphotic zone, depth integrated nitrogen (N) and phosphorus (P) values were 34 g-N/m2 (grams of Nitrogen per square meter of sea floor), 7 g-P/m2 in 1998 and 130 g-N/m2, 18 g-P/m2 in 1999, respectively. The results indicated that nitrogen (96 g-N/m2) and phosphorus (11 g-P/m2) are supported by up-welling and down-welling phenomena with convergence and divergence in the study area. Biological parameters in the water columns were largely determined by the physico-chemical environmental parameters. Subsurface chlorophyll maximum layers were coincided with the formation of seasonal thermocline. Copepods were the dominant group of zooplankton community at three sampling stations (N5, N6, N10) terms of abundance, which was the same results of previous surveys for the past 3 years. Among copepod populations, Oncaea sp., Oithona sp. Clausocalanus sp., Acarocalanus sp. and juvenile copepodites were dominant Appendicularians, foraminiferans and radiolarians were also dominant. To investigate diel vertical migration pattern of zooplankton, repeated samplings from the water depth of 0~50m and 50~200m were conducted at KODOS (Korea Deep Ocean Study) area before and after sunrise. Zooplankton abundance was slightly higher after sunrise than before sunrise in the surface layer. Chlorophyll-a concentrations were relatively low as the concentration of sediment increased in most experiments possibly due to a decrease of grazing pressure of microzooplantkon such as ciliates, which is the efficient grazer on small-sized phytoplankton. Because copepod predation on microzooplankton may be prevented by the high concentration of sediment, resulting in lower grazing pressure on small-sized phytoplankton. The results obtained during the baseline study as a part of KODOS project since 1998.

Jan 1, 2001

By Alexander Malahoff

Mineral zonation studies were conducted on hydrothermal vents of two hot spot volcanoes. One study site is located within the Axial Caldera of the axial hot spot volcano of the Juan de Fuca Ridge. The young high-temperature hydrothermal vent field consisting of two polymetallic sulfide chimneys, five meters high, located at 130°01.5'W, 45°56.5'N, along a fault complex at the base of the southwestern wall of Axial Caldera was sampled during four ALVIN dives in 1983. Temperatures of up to 270°C were measured within the orifice of one of the chimneys, which was then broken off and recovered with the submersible. Both black and white "smoke" was observed to be emanating from the one chimney sampled. The high-temperature chimney extends directly from a field of broken lobate lavas which are located at a water depth of 1,550 meters, about 200 meters east of the caldera wall. The chimney makes one of the shallowest active high-temperature vents studied to date. The vent is surrounded by clumps of vestimentiferan worms and is located within an elongate field of red-colored iron smectite blankets and chimneys. The low-temperature field forms a ribbon 150 meters wide, extending for about 1,300 meters at the base of the wall. Chemical analyses of the hydrothermal deposits ranging from the polymetallic sulfides of the chimney to the outer zones of the low-temperature field show a range of elemental assemblages consistent with temperature zonation around the vent. Chemical zonation within the high-temperature

Jan 1, 1988

By Eleanor Martin

An examination of the draft Exploitation Regulations from an investor’s perspective. We will look at the commercial requirements of the investment community (debt and equity) in order to provide funding to a deepsea mining project, and contrast this with the position put forward in the draft Exploitation Regulations. We will then recommend suggested amendments to the Exploitation Regulations to assist future investment on this growing industry.

Jan 1, 2018

By Joshua Brien

DEEP SEABED MINING IN NATIONAL JURISDICTION: KEY CHALLENGES The talk focuses on the key challenges that arise from deep-seabed mineral exploration and development within areas of national jurisdiction, including legal and institutional challenge and options to address these challenges. Joshua Brien has acted for a range of Governments throughout the world, including smallisland States and the developing world. This has included engagement in matters before the International Court of Justice, the Tribunal for the Law of the Sea in contentious and advisory proceedings, including provisional measures applications and prompt release cases.

Jan 1, 2018

By Stanley R. Riggs

Onslow Bay is a broad, shallow, high-energy shelf system bounded by the Cape Lookout and Frying Pan shoals. It is generally a sediment-starved shelf system dominated by hardbottoms with a scattered and discontinuous veneer of mobile Holocene sediments. Phosphate-rich beds of the Miocene Pungo River Formation crop out in a belt 150 km long and up to 50 km wide across the continental shelf in Onslow Bay, North Carolina. Previous research has demonstrated that a few of these beds contain vast quantities of potentially economic phosphate resources that occur in the surface and shallow subsurface sediments. Onslow Bay contains five phosphate-bearing beds predicted to include up to 20.7 billion tons of in-place phosphate concentrate with total sediment grades ranging up to 22.9% P2O5 and adjusted average concentrate grades of 29.8% P2O5. These phosphates are lithologically and chemically similar to phosphates currently being mined in the nearby Aurora phosphate district in North Carolina. Various lithologies of the Pungo River Formation and associated rock units of Oligocene and Quaternary age crop out on the sea floor to form extensive hardbottom habitats that dominate almost 100% of Onslow Bay. A large proportion of these hardbottoms appear to be sea floor deserts, whereas others are virtual oases with rich associations of benthic organisms. These important differences in benthic community structure appear to be greatly influenced by one or more of the following variables: 1) geologic framework (geologic formation, hardbottom composition, morphology, and spatial orientation relative to dominant currents and waves), 2) texture, movement, and accumulation of surface sediments, and 3) flow rates and chemical composition of discharged submarine groundwater.

Jan 1, 1992

By David M. Holmes-Smith

Many attempts have been made to design and build an AUV that is small, meets the sensing objectives and is cost effective. Many inventors have already designed smaller vehicles but the problem observed is an increased vehicle instability resulting in instrument instability where data gathered is not trustworthy. Additional problems include instrument weight to vehicle weight ratios and the lack of space for power storage and electrical components. The UFOceanic seeks to remedy these concerns by employing a completely different design and propulsion system. Still in the design stage ? now with a mock-up unit for testing, the results are encouraging. We have chosen a very low voltage embedded systems design using multiple PIC processors and fuzzy logic programming. We are designing the craft to rotate for stability and to provide friction reduction to minimize the need for instrument stability compensation and propulsion power. Additionally, we are looking and experimenting with a number of power plant drive systems including flywheels, GNP (plasma), fuel cells and more conventional systems. We of course plan for the UFOceanic to run for months at a time supported by a self-charging system.

Jan 1, 2001

By Richard Harrison, Frank Lim

"Lifting of slurry from the seabed mining machine to the surface production vessel is a critical element of any deepwater seabed mining system. A Vertical Transport System (VTS) comprises pump(s), riser string, connectors and hang-off assembly as its main components, but it is the pipe material, riser configuration and installation method that often attract the most discussions.This presentation will feature important VTS design work 2H has done over the years for different stakeholders, and highlight the work carried out as a partner to the EU funded Blue Mining Joint Industry Project.The key challenges faced by a deepwater VTS are:??High riser payload??Large deck space for storing riser joints??Long time to deploy and retrieve riser??Uncertain metocean conditions??Vortex induced vibrations??Weld and connector fatigueIncreasing the water depth further sees the longer and increasingly ‘springy’ riser experiencing axial resonance caused by wave induced vessel heave motions being close to the riser resonant period. This can lead to snatch loading and fatigue failure in the riser.The presentation will discuss the above design issues, analysis requirements and provide guidance on pump/riser selection. Solutions to mitigate the resonant response issues will also be proposed.."

Jan 1, 2017

By Christina Pomee, John Parianos

"TOML’s ISA Contract comprises six areas (A-F) that span from 118° to 152° W and from 7° to 15° N or over 70% of the CCZ.During a 2015 exploration cruise, TOML scientists found that the a logging system developed by ISA (2010) was able to be adapted and enhanced, to describe in some detail the varied morphology of nodules both within the TOML areas and between them.The shapes and sizes of nodules seen were then found to relate to substrate type and setting, and thus likely thickness and long-term stability of the geochemically active layer. Consideration of the various processes that might influence growth helps constrain nodule formation further. The nodules effectively record the long-term geochemical conditions that lead to their formation.ISA (International Seabed Authority), 2010. A Geological Model of Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone and Prospector’s Guide for Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone. International Seabed Authority Technical Study: No. 6 ISBN: 978-976-95268-2-2"

Jan 1, 2017

By Lars-Kristian Trellevik, Jan Arvid Ingulfsen

Swire Seabed is dedicated to being at the forefront of the Autonomous Subsea Revolution. The company is currently working along and developing operational, technical and market strategies where autonomous technology is the driving force. Swire Seabed’s vessel Seabed Constructor is currently mobilized and operating eight Hugin AUVs and 6 Surface going USVs. This significant and revolutionary spread is owned by Ocean Infinity. Ocean Infinity and Swire Seabed is currently involved in the search for the missing MH370 – in about 3 months the vessel and autonomous spread have fine combed an area of deep sea floor spanning over more the 100 000 km2 . With such a considerable spread with a depth rating of 6000 meter – Swire Seabed and Ocean Infinity is challenging long held paradigms in subsea mapping and resource surveys. Highly accurate and precise data can be acquired for large areas in record time, and at a comparatively much reduced cost. As one earlier required several vessels and associated crews and logistical support – Swire Seabed and Ocean infinity are now able to operate a large number of AUVs and USVs, through technological advances in automatic data-processing and interpretation, from a single offshore vessel. This opens up vast possibilities for emerging markets such as subsea-minerals. Swire Seabed is also developing strong collaborative relationships with academic institutions. Along with UIB Swire Seabed is developing methodology for deep sea geological and geophysical resource searches applying AUVs at an industrial scale – this work is based on UIBs groundbreaking work and significant experience in the same fields. In particular Swire Seabed and K.G Jebsen Centre for Deep Sea Research (UIB) have developed methodologies for conducting detailed Seep-Searches at a large geographical scale. UIB and Swire Seabed is further pursuing a formalized long term relationship for academic and industrial cooperation and exchange in AUV operation and methodology development. Whilst K.G Jebsen Centre for deep sea research have been involved in basig deep sea research for years, Swire Seabed have specialized in cost-effective heavy duty operations in water depths greater the 3500 meters. This collaboration affords the subsea mining community a unique pool of both insight and operational capacity.

Jan 1, 2018

By Steve Potter

"REVIEW OF ISA's DRAFT EXPLOITATION REGULATIONS – HAVE KEY STAKEHOLDERS' CONCERNS BEEN ADDRESSED ADEQUATELY?In early August 2017, the ISA published a revised draft of the exploitation regulations. My presentation will focus on the extent to which key State and Contractor issues raised in formal submissions in November 2016 have been addressed in the revised draft and any additional key issues in the revised draft which are likely to cause significant concern for Contractors.ABSTRACTFollowing the ISA's call for submissions in response to draft zero of the exploitation regulations in July 2016, 43 responses from stakeholders were received by the ISA in November 2016. My presentation will start by briefly looking at how the ISA has continued to engage with stakeholders following the publication of draft zero of the exploitation regulations, including at payment regime workshops in London (November 2016) and Singapore (April 2017) and at the environmental workshop held in Berlin in March 2017. It will also touch on the publication in February 2017 of what was in effect a very preliminary draft of the environmental regulations before moving on to consider in detail the extent to which key State and Contractor issues have been addressed in the ISA revised draft exploitation regulations which were published in August 2017. My review of the formal submissions will include, amongst other things, commentary on:(i) the level of Stakeholder response (State Parties to UNCLOS, Sponsoring States, Privately owned Contractors, State Owned Contractors and NGOs);(ii) the quality of the submissions (particularly by States and Contractors); (iii) the key concerns raised by State and Contractor stakeholders and how those issues have been addressed in the revised draft exploitation regulations; and(iv) how all stakeholders need to further engage with the ISA to ensure that the exploitation code adequately addresses the legitimate and reasonable concerns of each Stakeholder group (e.g. Contractors, Sponsoring States, Developing States and NGOs)."

Jan 1, 2017

By Daniel E. Walsh

The recovery of most minerals, which are amenable to gravity concentration, is standardly determined by accurate sampling and assaying. .With respect to particulate - gold ores, sampling and assaying are still the convention, but the accuracy and reproducibility of these operations are much discussed and debated points. Evaluation of gravity concentrators by conventional sampling and assaying techniques is very time consuming, costly and may introduce a large amount of uncertainty into the results due to the particulate nature of placer gold. These problems are not unique to placer gold ores and apply to any low grade ore with particulate values. A gravity concentrator evaluation process developed by MIRL employs the use of neutron activated gold (198Au) and radiation detection circuits which monitor the concentrator's product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems. Beginning in 1984, MIRL conducted radiotracer studies of unit processes, which included jigging, static wedge wire screening, elutriation, and concentration with compound water cyclones.

Jan 1, 1989

By R. D. Hamer

"The Atlantis II Deposit comprises metalliferous sediments (Zn+Cu+Ag+Au) accumulating in a composite, axial basin, 2,000m beneath the surface of the Red Sea. The basin contains warm, highly saline water. It is located approximately half way between Jeddah and Port Sudan within the Exclusive Economic zones of Saudi Arabia and Sudan. The Deposit was discovered in 1963 and evaluated by drilling in the 1970s and 1980s. This phase defined an initial resource of approximately 90Mt. More recent estimations have refined this figure to an Inferred Resource of approximately 80Mt (CIM compliant).The Mining Licence to develop and extract the Atlantis II Deep Deposit was granted to Manafai International Trade in 2010 by the joint Saudi-Sudanese Red Sea Commission. Manafai is poised to embark on a renewed phase of exploration and evaluation, including the completion of a Definitive Feasibility Study (DFS) and leading to the successful exploitation of the Deposit in a safe, environmentally sound, economically viable and socially responsible manner.The Deposit is forming in a complex basin adjacent the median rift, where sea floor spreading has operated during the last 5Ma. It is a Hydrothermal-sedimentary Deposit. The mineralised sedimentary rocks rest directly on sea floor basaltic rocks. They are produced by the exhalation of metal-rich, hydrothermal brines from fissures associated with the central rift and cross-cutting fracture zones. Up to 25m of metal-rich sediments have accumulated over an area exceeding 57km²."

Jan 1, 2017

By Steven D. Scott

The source of ore metals for base and precious metal volcanogenic massive sulfide (vms) deposits has been debated for decades. Metals can be obtained from high-temperature sea water-rock reactions in subseafloor circulatory hydrothermal systems, or provided by the magmatic fluids that are degassed from magma. The magmatic signatures are largely erased in the hydrothermal system by the overwhelming, long-term circulation of seawater. Melt inclusions in phenocrysts (plagioclase, olivine, pyroxene) of volcanic rocks provide an effective means of understanding the potential for a magmatic contribution to the ore-forming fluids. We present results of a melt inclusion study on the volcanic rocks that host active seafloor hydrothermal fields in the eastern Manus immature back-arc pull-apart basin of Papua New Guinea and an Ordovician-age back arc in New Brunswick, Canada that hosts the ?giant? (330 mmt) Brunswick #12 vms ore deposit. A fluid phase is typically observed in cavities within melt inclusions, indicating that the magma was saturated with volatiles prior to its eruption. The fluid is CO2-dominated with lesser H2O and CH4 in melt inclusions of mafic volcanics and is H2O-rich in felsic volcanics. Tiny crystals and amorphous precipitates (recrystallized at Brunswick #12) of Fe, Ni, Zn, Cu and Mn chlorides, sulfides and oxides coat the walls of the vapor cavities. The crystals include magnetite, magnesite, calcite, anhydrite, gypsum, barite, pyrite, chalcopyrite, halite, silicates and apatite. At Manus, the compositions of the precipitates on the bubble walls of melt inclusions are similar to those found in the vesicles in the matrix glass of the same sample. The ore metals in the volatile phases changed from Ni+Zn+Cu+Fe ? Cu+Zn+Fe ?Fe+Zn (+Pb?) as the magma evolved from basalt, basaltic andesite ? andesite, dacite ? rhyodacite, rhyolite. Glass of the melt inclusions compared to that of the matrix of the rocks from Manus have significantly higher concentrations of H2O (av. 1.64 vs 0.7wt%), Cl (av. 2500 vs1300 ppm) and S (av. 900 vs 100 ppm) suggesting that these volatiles were extensively exsolved from the magma. A minimum of 1.0 to 1.7wt% of magmatic volatiles is estimated to have been degassed before and during the eruptions. The focused discharge of a magmatic fluid as a result of pre-eruptive degassing could be responsible for the metals in the sulfide deposits on the seafloor. If 1 km3 of magma were emplaced in a shallow chamber, then the associated magmatic fluid would be 35.1 million tonnes. If this fluid contained 2.3 wt% Zn and 7.2 wt% Cu (Yang and Scott, 1996, Nature), a total of 0.8 million tonnes of Zn and 2.5 million tonnes of Cu would be to the hydrothermal system.

Jan 1, 2005

By M. Ravindran

The Government of India started its deep seabed exploration programme during 1982. This programme was started as one of national importance and several national laboratories were involved to realize the development of requisite technologies for deepsea mining and processing. After a concentrated effort on surveying, using its own as well as hired ships, India succeeded by mid 1980s in identifying a prospective site in the Indian Ocean as an exclusive claim for development. India was registered as a Pioneer Investor and became the first country to obtain this status on 17th August 1987. India has been allocated an exclusive mine site of 150,000 km2 in the Central Indian Ocean. Our country also developed considerable expertise in the metallurgical processing for extracting metals from these nodules. The Department of Ocean Development, Government of India, the organization which is designated as the nodal agency responsible for implementing the deep seabed mining programme has drawn up a long term plan which will enable it to fulfill its obligations as a Pioneer Investor. The work toward the design and development of a mining system has been entrusted to the Central Mechanical and Engineering Research Institute, Durgapur. As a part of this programme they have developed a nodule collector and a riser system which have been tested in very shallow waters only. Since this technology development for deep sea mining applications is highly time consuming and very expensive, this programme is also being used to develop components for intermediate applications. In view of the long timeframe required for perfecting a deepsea nodule mining technology, the Government of India is also keen on developing shallow water mining systems for utilizing the placer deposits. One of the richest heavy mineral deposits in the Indian Exclusive Economic Zone is available on the west coast of South India in the state of Kerala. The coastal stretch between Kanyakumari, on the southern tip of India, and Alleppey along the west coast at a distance from the tip of approximately 210 km, there is a good multimineral reserve. The initial survey indicates that the estimated reserves in the surveyed areas are approximately as follows: Ilmenite 1.4 million tonnes Rutile 0.14 million tomes Zircon 0.13 million tomes Sillimanite 0.53 million tonnes

Jan 1, 1994

By Pedro Madureira, Georgy Cherkashov, Harald Brekke, Marzia Rovere

"The most promising deep-sea mineral resources for exploration in the Area (beyond the limits of national jurisdiction) are polymetallic nodules, cobalt-rich ferromanganese crusts and polymetallic sulphides. These marine minerals have different characteristics in their distribution, geological setting, grades of metals and genesis. Considering future exploitation of nodules, crusts and sulphides such parameters as estimated resources, specific mining operations and ore processing are different as well.Comparative analyses of deep-sea mineral minerals as well as onshore and offshore resources will be discussed in the paper."

Jan 1, 2017

By Kiseong Hyeong

The Intertropical Convergence Zone (ITCZ), where the southeast and northeast trade winds converge, is the effective climatological barrier that separates the southern and northern hemispheres in terms of dust budget. Asian and N. American dusts dominate in the Pacific north of the ITCZ, while Central and S. American dust prevails south of the ITCZ. In order to understand the nature of latitudinal and depth-related variations of mineral composition in terms of position relative to the ITCZ, deep-sea core sediments were collected from 9°N to 17°N at a 2° intervals along the 131.5°W meridian and analyzed for mineral composition. The amount of illite in surface sediments decreases gradually from 65% at 17°N to 31% at 9°N. In contrast, smectite increases from 11% to 56% southward. The observed mineralogical variation toward the ITCZ is attributed to the increased supply of volcaniclastic material transported via the southeast trade winds from the Central and South America source regions. Smectite-illite transition, a phenomenon that the amount of smectite increases over illite, occurs at around 10°N, the northern margin of the ITCZ. This result indicates that the change in latitudinal position of the ITCZ in the geological past could be recorded by the smectite-illite transition in deep-sea cores. The cores studied show down-core variation of mineral composition from illite-rich at the surface to a smectite-rich clay suit at depths, similar to the latitudinal variation. The smectite-illite transitions observed in these cores are likely the records of changes in latitudinal position of the ITCZ. The depth and age of the smectite-illite transition is getting shallower and younger towards the equator, implying that the ITCZ was located farther north during late Tertiary and has shifted southward to the present position of 5°N~10°N.

Jan 1, 2004

By G. Cherkashov

A new hydrothermal field with massive sulfide deposits was discovered in 2004 at 16º 38.4?N, 46º 28.5?W on the Mid-Atlantic Ridge. Hydrothermal signals had already been recorded from bottom waters and sediments in this area during cruise 19 of R/V Professor Logatchev in 2000. This site was revisited during the 24th cruise of R/V Professor Logatchev in February 2004 when samples of massive sulfides were recovered and video records of the deposits made. The basalt hosted hydrothermal field is situated at a depth of 3700-3750 m, 600 m above the inner floor on the eastern slope of the rift valley. Structurally, the new field is located at the intersection of a deep along-axis marginal fault and a transverse sub-latitudinal dislocation. Six sulfide mounds as well as associated metalliferous sediments were mapped (sampled and/or recorded by video profiling) within the hydrothermal site. The largest ore body, 500 x 225 m, in the southern part of the field consists of small blocky talus and relics of sulfide chimneys partly covered by iron oxyhydroxides. The chimneys are 1-5 m high. The southern and western boundaries of the massive sulfide deposit have not yet been delineated. More than 1,100 kg of massive sulfides and stockwork mineralization were sampled at 7 sites by dredge and TV-grab. Everywhere, iron sulfides were the principal minerals present. Pyrite in association with lesser amounts of chalcopyrite occurs in both massive sulfides and stockwork mineralization. Of particular interest is the chalcopyrite-siliceous stockwork where silicified and chalcopyritized basalts are intruded by a network of chalcopyrite veinlets. These zones could be fairly thick and enriched in base metals. Sphalerite was very rare.

Jan 1, 2004

By Timothy F. McConachy

Magmatic-hydrothermal activity in the South-West Pacific and SE Asian island arcs during the Tertiary has created a premier copper-gold province with numerous, commercially attractive base and precious metal deposits. This activity continues to the present day, especially in submarine sectors of those arcs where modern technologies enable direct observation of ore-forming processes in action. Until recently, however, the volcanic island arcs of Indonesia escaped such attention. The Indonesia-Australia Survey for Submarine Hydrothermal Activity (IASSHA), involved three cruises with KR Baruna Jaya VIII, focused particularly on the Sangihe arc; Tomini Bay, Sulawesi, including the vicinity of isolated Colo volcano; and the Sunda Strait including the neighborhood of Krakatau volcano. IASSHA 2001 and 2003 cruises studied the arc and behind-arc sectors of the Sangihe volcanic island chain extending northwards from Quaternary volcanoes on the northeastern tip of Sulawesi, near Manado, to the Kawio Islands near the border with the Philippines (Fig. 1). This chain lies above a west-dipping Wadati-Benioff seismic zone whose subduction trench is obscured by accreted sediments and mélange, forming the Talaud-Mayu ridge. West of the main active chain and extending northwards from Manado there is a subparallel ridge (The Manado Line) surmounted by a number of high (>2000 m) seamounts of uncertain age.

Jan 1, 2005

By Georgy Cherkashov, Tamara Stepanova, Anna Firstova

INTRODUCTION High tellurium contents in the ancient volcanogenic massive sulfides (VMS) and modern seafloor massive sulfides (SMS) have been reported by V.Maslennikov (Maslennikov et al., 2013). However findings of tellurium minerals in SMS are rather rare. The only reported coloradoite and bi-melonite, have been found in massive sulfides from Rainbow hydrothermal field (Fouquet, 2010). Here we present data about Te - minerals in sulfide chimneys of different ages (up to 84.7 kyr - Cherkashov et al., 2010 ) from Semyenov-2 hydrothermal field. The obtained results The Semyenov hydrothermal cluster was discovered and studied in the course of cruises 30 and 32 of R/V Professor Logachev (2007 and 2009) at 13º31´ N, MAR. This area is associated with an oceanic core complex and associated with serpentinized gabbro- peridotites and basalts. Plagiogranites and tonalites have been dredged on seafloor in the Semyenov cluster area (Cherkashov et al., 2013; Pertsev et al., 2012). In total, 25 sulfides samples have been studied. The major and minor mineralogical phases were identified using reflected light microscope. Major element compositions of ore- forming minerals were analyzed on a Hitachi S3400N scanning electron microscope at the Geomodel Center, St. Petersburg State University (St. Petersburg, Russia) with an AzTec Energy 350 (EDX) detector and an INCA 500 (WDX) detector.

Jan 1, 2018