Search Documents

By Marco Le Roux, Martha Van Rensburg, Quentin Campbell

Fluidised bed drying is currently receiving much attention as a dewatering option during the beneficiation of fine (defined here as between 1 mm and 2 mm particles) coal. Apart from concerns about safety and combustion, the operating costs can be high if very high gas or air temperatures are used. The aim of this study was to investigate the removal of moisture from fine coal by using air at a lower temperature (25 - 55°C) within a controlled environment by lowering of the relative humidity of the air. It was firstly proven that fluidization has a major advantage over non-fluidized beds, with regards to drying rate and final moisture content. Hereafter several parameters that influence the dewatering rate and final moisture content were tested, from which it was concluded that the relative humidity of air acts as the largest driving force for dewatering. Parameters tested included relative humidity, temperature and coal composition. Energy balances showed a positive nett energy increase in the dried coal during combustion when related to the energy input during drying. In comparison with thermal drying technologies, fluidized bed drying was proven to be less energy intensive. It was therefore shown that this is a viable technology for the dewatering of fine coal.

Jan 1, 2014

By P. K. N. Raghavan

Bauxite is the principal source for the production of aluminum metal which has gained tremendous importance over the years due to its versatility as a metal capable of substituting almost all of the non-ferrous metals, non metals like wood, plastics, fibre glass, etc. and even steel in many applications. 90% of the high purity alumina needed for the production of this wonder metal in the world comes from bauxite. Even though alternate methods have been developed to produce alumina from non bauxite sources, owing to the high capital and operating costs involved, Bayer process still retains the superiority among all the methods by virtue of its simplicity and favourable economics. Bauxite continues to be the perfect ore for alumina production and its remarkable utilization makes it the most important non-ferrous ore. Most of the Alumina Refineries in the world process different types of bauxite and that too from varied sources. The technology employed in the Alumina Refineries depends on the Bauxite processed, with an ultimate view to produce alumina of required quality in the most efficient manner. Bureau of Indian Standards (BIS) and Indian Bureau of Mines (IBM) had from time to time put forward bauxite specifications for metallurgical and other applications. However, these are found no fully based on alumina technology, present developments and availability of different types of bauxite in the country. The aim of this paper is to provide scheme of metallurgical grading of Indian Bauxite based on the background of alumina processing technologies and availability of various types of bauxite in the country. Efforts are made here to evaluate beneficiation techniques for central Indian Bauxite from the point of view of alumina production. Keywords: bauxite beneficiation, digestion, alumina, gibbsite, bohemite, diaspore

Sep 1, 2012

By Xiaoming Wang

This paper describes a new magnetic separator integrating dynamic permanent magnetic force, gravity and flow dynamics to enhance the quality of the iron concentration. This equipment can increase the grade of concentrate by controlling the formation of magnetic agglomerations to reject most gangue. Test results indicates that the compound force field separator can be applied in improving the quality of iron concentrate and has a wide range of potential market applications. Keywords: magnetic separator, compound force field, rotating magnetic system, magnetite concentration

Sep 1, 2012

By Homero Delboni, Mauricio Guimarães Bergerman

"At the regrind or secondary grinding stages of metal ores, usually the concern about the energy efficiency is extremely important. In general, the specific energy consumption at this stage is higher than in the primary stages of grinding. In addition, it has been observed a tendency of finer grinding in the new projects of metallic ores, due to the finer mineral liberation, which leads to an increasing capital and operational costs. In Brazil, during the last 10 years, regrind P80 sizes of approximately 40 to 20 ?m have been necessary in all new iron and copper plants. The use of conventional ball mills, adequate for primary grinding, can result in low energy efficiency with products below a P80 of 50 ?m. This paper presents an overview of the regrind circuits in Brazil that operate with vertical mills and the results of industrial surveys at selected vertical mill circuits. Where possible, comparison is made between the plant results and the design criteria and laboratory regrind tests used for the mill sizing."

Jan 1, 2014

By M. S. Eygi

This study covers the investigations based on the electrokinetic and rheological properties to explain the interactions between kaolin minerals and commercially available polyelectrolyte in anionic character. Additional adsorption test were also conducted to support the interaction mechanism. Adsorption tests showed that adsorption densities decrease by increasing the solid content. In-creasing the solids contents from 1% to 30% by weight resulted in the decrease on adsorption from 2.14 mg/g to 1.85 mg/g. Because of its difficulty, the solids ratio at 70% was not studied. However, following to trend of the curve plotted adsorption density-solid ratio, an estimation was made and adsorption density at 70% solid content was extracted from the curve as 1.75~1.80 mg/g. The electrokinetic studies pointed out that the presence of polyelectrolyte increase the zeta potential of kaolin from 40 mV to 60 mV which is reasonable conditions to disperse and stabilize the kaolin slurry and lower the viscosity. When these result of the different tests are combined and considered together, 2 mg/g polyelectrolyte concentration was noted as optimal concentration where adsorption density, viscosity and zeta potential of the slurries give maxima and remain constant after this concentration.

Jan 1, 2014

By Yuriy V. Gulyaev, Galina V. Sedelnikova, Valeriy D. Lunin, Valentin A. Chanturiya, Igor J. Bunin

"In Russia the industrial exploitation of ore deposits is determined as a strategic direction of gold extraction industry development. The majority of gold-containing ores of Russia is referred to category of rebellious ores with 3-5 g/t gold content and is characterized by low factors of gold and silver extraction under cyaniding. The resistance of goldcontaining raw materials under their processing is caused by presence of very fine gold particles less than 0,1-0,01 µm in size, associated with the pyrite and arsenopyrite. Significance of the problem of rational rebellious ores beneficiation and high precious metals extraction is increasing from year to year.Group of scientists from IPKON and IRE, Russian Academy of Sciences, has developed highly effective, powereconomic and ecologically clean method of breaking-up of resistant gold-containing ores and their beneficiation products on the base of using an energy of powerful electromagnetic pulses. For the first time there have been designed laboratory installation for resistant raw materials treatment in dry and wet state (solid/liquid ratio = 5:1) and ground material less than 1-0,5 mm.Mechanisms of powerful electromagnetic pulses action on natural mineral components, including dielectrics (quartz, calcite), semiconductors (sulfides) and metals (gold, silver) have been theoretically accounted. Pulses action parameters and ways of pulses generating have been discussed in different conditions. At tension of electromagnetic field, exceeding the electric strength of processing material, an electric breakdown develops in the mineral matrix of sulfides and dielectrics. Under the series of pulses action the forming of plural breakdown channels occurs, leading to strength loss of material and microcrackes developing. Thus, the action makes it possible for leaching solution to access precious metals particles under cyaniding process. Distinctive changing of pyrite and arsenopyrite surface structures under the influence of powerful electromagnetic pulses is confirmed by studies using optical and scanning electron microscopy."

Jan 1, 2003

By S. M. Wen

In mineral processing, the settling of mineral particles in water, the flow of ore pulp, the dewatering and filtering of concentrates and so on, are related to the pulp viscosity. While the interaction between mineral particle surface and water affects directly the pulp viscosity. Therefore, it is of great value to the development of mineral processing theory to research the effect of mineral particle surface on the water viscosity in boundary layer. In micro-fluid, the effect of mineral particle surface on the water molecules in boundary layer can not be ignored. The water viscosity in boundary layer and the effect of the nature of mineral particle solid surface on the viscosity are analysed based on the deduction of attraction potential energy formula of mineral particle surface to the water molecules in boundary layer. The results show that the attraction potential energy of mineral particle surface to the water molecules in boundary layer is determined by the properties of solid molecules and fluid molecules and varies inversely as the third power of the distance from mineral particle surface. The water viscosity in boundary layer consists of the viscosity of free water and the additional viscosity resulting from the attraction of mineral particle surface. The increment of the viscosity caused by the attraction of mineral surface is µs. This additional viscosity is also inverse ratio to the third power of the distance from mineral particle surface. The greater the dipole moment, the polarizability and the ionization energy of mineral particle solid surface molecules are, the higher the attraction potential energy of mineral particle surface to the water molecules and the water viscosity in boundary layer are. The thicker stationary water boundary layer is d0. The higher the µs is, in other words, the greater the attraction of solid surface to water molecules is, the thicker the stationary water boundary layer becomes when free water viscosity is constant.

Jan 1, 2014

By Carlos de F. Gontijo

The flotation of quartz particles was studied over the particle size range from 0.5 µm to 1000 µm and for advancing water contact angles between 0º and 83º. Flotation was performed in a column and in a Rushton turbine cell. Particle contact angle threshold values, below which the particles could not be floated, were identified for the particle size range 0.5~1000 µm, under different hydrodynamic conditions. The flotation response of the particles, either in a column or in a mechanically agitated cell with a similar bubble size, was comparable. Turbulence plays a role, as does bubble-particle aggregate velocity and bubble size. The stability of the bubble-particle aggregate controls the maximum floatable particle size of coarse particles. For fine particles, the flotation limit is dictated by the energy required to rupture the intervening liquid film between the particle and bubble. Flotation of very fine and large particles is facilitated with small bubbles and high contact angles. These results greatly extend our earlier observations and theoretical predictions.

Jan 1, 2014

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei. These ores require mineral processing to remove the sub-strate/nuclei rock before smelting. This paper reviews experimental results of previous investigations. Observations and analysis of 10 samples from different localities were carried out and it was found that the liberation ratio of crushed product was high even at coarse size fraction, 0.5mm to 4mm. Experimental and calculated results in the smelting stage confirmed that the separation product satisfies the standards of the subsequent smelting process if the substrate/nuclei rock is removed from the 0.5mm to 4mm fraction with high separation efficiency. There was a density difference between the substrate/nuclei rock and the ferromanganese component. Thus the coarse sized sample was treated with gravity separation; air table separation was used as a dry method and jig separation as a wet method and high grade values with high recoveries were obtained by both kinds of gravity separation.

Jan 1, 2014

By T. C. Alex

Mechanical activation of gibbsite [?-Al(OH)3] is the theme of this paper. Industrially prepared gibbsite used in the study has a mono modal size distribution with a median size, d50=110 µm. Mechanical activation of this gibbsite has been carried out in a planetary mill at ambient conditions. Mechanical activated gibbsite samples are characterised in terms of particulate characteristics, structural characteristics and reactivity. As a result, of milling, mono modal size distribution of the unmilled gibbsite changes to a broad multimodal distribution. Size reduction has been sharp in the initial stages of milling; median size reduces to ~7 µm during 15 min of milling. Thereafter no decrease in median size is observed; rather it is found to increase gradually with further increase in milling time, indicating particle aggregation. Morphological studies of milled gibbsite have shown that the platelets forming the agglomerate are separated first; the separated platelets then undergo breakage. Aggregation of particles sets in the later stages of milling as a result of increased surface area and surface energy. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies have clearly revealed the changes in gibbsite structure during milling. Analyses of XRD data show that the crystallite size of gibbsite decreases as the milling time progresses whereas its microstrain is found to increase. Accumulation of energy in the structure is the result in both cases. TEM micrographs with signs of defects leading to disordering of gibbsite structure complement the XRD results. Reactivity of milled gibbsite, decrease in its deydroxylation temperature and increase in alkali dissolution, is found to increase with mechanical activation. Increased reactivity of milled gibbsite is found to have a strong correlation with the BET specific surface area. Keywords: mechanical activation, gibbsite, alkali dissolution, thermal dehydroxylation, reactivity

Sep 1, 2012

By Christian O’Keefe, Alex Van der Spek

"Evaluation of inequalities of the partial sums defining cumulative grade and recovery prove that cumulative grade has an upper bound not dependent on the bank number and cumulative recovery possesses an upper bound proportional to the bank number. This explains one observed characteristic of cumulative grade versus cumulative recovery curves. The existence of such maxima combined with the observed shape of cumulative grade-recovery curves leads us to postulate that these curves can be well described by rectangular hyperbolae. Rectangular hyperbolae are characterized by asymptotes at right angles to each other. It is proven that this property can be used to derive an equation for the cumulative mass flow of the concentrate in terms of the asymptotic values of cumulative grade and cumulative recovery. Fitting hyperbolae to experimental cumulative grade cumulative recovery plant data then results in estimates of the maximum grade, the maximum recovery and a constant which may be taken as a performance coefficient of a row. Normalization of the cumulative grade and the cumulative recovery by their respective maxima gives rise to a graphical representation that can be used to evaluate the operating performance of a row of floatation bank cells. The normalization procedure removes the bias that is introduced by inevitable variation in mass flow of the feed and variation in feed mineralogy or feed particle size distribution. Reduction of the normalized data collapses all cumulative grade-recovery data onto one and the same curve. This removes the differences caused by the variation in row performance. The reduced cumulative grade-recovery data scatters around a common hyperbola. This can be used to gauge the validity of the assumptions made. Normalized cumulative mass pull is determined from the fitted values of the maximum recovery and maximum grade. This may serve as an alternative performance indicator of the floatation row."

Jan 1, 2014

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

The present investigation aims to develop and distinguish mineral specific reagents with two functional groups for use in flotation of calcium containing minerals. For this purpose, a series of dicarboxylate-based surfactants with varying length between the carboxylate groups (one, two or three methylene groups) were synthesized. As reference, a surfactant with the same alkyl chain length but with only one carboxylate group in the polar part was synthesized. The adsorption behavior of these new reagents on pure apatite and calcite mineral surfaces was studied using Hallimond tube flotation, FTIR and ? potential measurements. The relation between the adsorption behavior of a given surfactant on a specific mineral surface and its molecular structure over a range of concentration and pH values, as well as the region of maximum recovery were established. It was found that one of the reagents, with a specific distance between the carboxylate groups, was much more selective for a particular mineral surface than the other homologues synthesized. This selective adsorption of a given surfactant to a particular mineral surface relative to other mineral surfaces as evidenced in flotation studies is substantiated by ? potential and infra-red spectroscopy data.

Jan 1, 2014

By Michael Young, Rodrigo Araya, Cesar Gomez, Le Huynh, James Finch

The performance of flotation machines is closely related to the gas dispersion characteristics achieved in their operation. It is known that frothers play a major role not only in the size distribution of the generated bubble population, but also on the swarm rise velocity. A program to characterize frother effects on two-phase hydrodynamics (air-water) of Jameson cells was undertaken in a fully instrumented pilot unit installed at McGill University. Gas dispersion parameters (gas velocity, gas holdup and bubble size distributions) of the gas-liquid mixture generated in the downcomer were measured after its release into the separation chamber. The unit was operated under different conditions including gas velocity, liquid jet velocity and frother concentration (MIBC). Bubble size distributions for concentrations above the critical coalescence concentration (CCC) were narrow with Sauter mean diameter between 0.6 to 1.3 mm. The bubble size followed the general trend as encountered in other types of flotation machines, i.e., rapid decrease with increasing frother concentrations below 10 µL/L, and almost no change in size for concentrations above 30 µL/L. The CCC was between 10 and 15 µL/L. Strong correlations were found between bubble size and air-to-liquid flow ratio (APR), and between the bulk density of the aerated solution in the separation tank and the vacuum inside the downcomer. An equation is proposed to estimate gas holdup in the separation tank from vacuum and bulk density readings.

Jan 1, 2014

By M. Morales, J. Yianatos

"In this work, an alternative approach to evaluate the flotation performance along a flotation rougher row is presented. The collection zone as well as the froth zone performances were separately evaluated. For this purpose, sampling for metallurgical balances along with sampling of top-of-froth (TOF) grades in each cell of a flotation row were employed. The modelling of the rougher circuit consisted of using TOF grades for evaluating the collection zone recovery, because they are a good representation of the bubble loading, which identifies the true flotation process, as shown in previous studies for shallow froths. In addition, the feed characterization, size-by-liberation, allowed the identification of the mineral distribution and its evolution along the circuit. The latter result was obtained by fitting the recovery profiles as well as the TOF grades down the flotation bank. The flotation rates and the maximum recoveries in terms of size-by-liberation (size classes: -45 µm, +45-150 µm, +150 µm, and liberation classes: -20%, +20%-80%, +80%) were then estimated. The results were in good agreement with those reported in literature by other authors and showed the new approach allows flotation kinetics to be characterized in industrial circuits.INTRODUCTIONMineral recovery in industrial flotation circuits is a function of the mineral characteristics, such as particle size distribution and liberation (Trahar, 1981, Jameson, 2012), and operating conditions such as air flowrate, pulp flowrate, solids percent and reagent conditioning (Jameson 1977; Klimpel, 1980; Mehrotra and Kapur, 1974). The cell type and size (self-aerated or forced air) and the circuit arrangement (single cells or banks of cells in series) are also relevant factors. Sampling of circuits (e.g. rougher, cleaner or scavenger) are commonly carried out using standard automatic samplers for metallurgical balance assessment. However, the flotation plants are generally not provided with proper accesses for local streams, which hinders the recovery estimations and the flotation rate characterization."

Jan 1, 2018

By K. Saberyan

Zirconium and hafnium are two important elements in nuclear industries. Zirconium is used in fuel rod for its low neutron absorption. Hafnium should be separated from zirconium, because it has higher neutron absorption cross section. In this research, separation process of the mentioned elements from (Zr+Hf)Cl4 mixture produced in the Zirconium production plant (ZPP) of Iran (Esfahan) was studied employing solvent extraction method in the nitric acid medium by using tributylphosphate (TBP) as solvent, and kerosene as diluent. The effects of nitric acid, sodium nitrate and amount of extractant, zirconium concentration in aqueous phase, phase ratio, agitation time, and mixer agitation rate were investigated on the separation process. The process was optimized at 5 M nitric acid, 1 M sodium nitrate, 60% (v/v) TBP. The optimum values for phase ratio, agitation time and agitation rate were 1.5 min and 500 rpm respectively. In this condition, the zirconium extraction efficiency, and separation factor were 65.1% and 205.59, respectively. Finally, we accessed to nuclear grade in this research.

Jan 1, 2014

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By Peter Ay, Elena Geldt, Satyanarayana Narra, Claudia Glaser

"As part of an extensive research and development project, the technical and technological implementation of the patents DE 10 358 245 B4 and WO/2006/056172 was developed with the goal to present a system for the innovative roll- agglomeration method exhibiting a) a modular setup, b) high productivity and c) suitability for the use of fibres of different applications and product qualities (high technical availability). The processability of the rarely adapted raw fibre materials into high-value intermediates brings forward their application in various processing industries dealing with the production of fibre reinforced plastic composites, heat and sound insulation materials as well as with the gas and liquid cleaning systems. The innovative fibre agglomeration presented in this work is performed by a combination of rolling and pressing the fibres inside a geometrically pre-defined roller table, in which the fibres are forced to bound through entanglement / interlocking and develop into agglomerate. The agglomeration process is carried out in a circular roller path with a rectangular cross-section. For improving the adhesive properties, and thus the quality of the agglomerates, the boundary surfaces can be covered / patterned / lined / coated with various materials. The resulting roll-agglomerates are characterized by different quality parameters such as mass, shape, porosity and stability. The properties of the agglomerates can be modified based on the end-product requirements by slightly modifying the process parameters such as filling ratio, residence time, roll-geometry, procurement of the boundary surfaces, etc. as well as the input material properties such as fibre type, fibre fineness, fibre length, etc. This work carries extensive work on the roll-agglomeration system to assess the effectiveness and the variability based on the product specifications. Agglomerates were produced with wide variations of system parameters with varying roller table liners and based on evaluation of the produced agglomerates with respect to their mass, the geometrical dimensions, their porosity and stability."

Jan 1, 2014