Search Documents

By Williams Calderon, César Arredondo, Gonzalo Montes-Atenas

The quality of final concentrate in froth flotation circuits is largely dictated by the correct implementation of the froth washing operation in flotation cleaning stages, which are commonly installed in column flotation cells. In flotation plants, this aspect has been largely overlooked and the froth washing is restricted to the use of perforated piping through which process water flows producing a similar effect to that observed in "fountains": jet created with low energy crosses the froth phase washing out entrained particles as well as particles weakly attached to bubbles. The aim of this research study is to assess the efficiency of traditional froth washing systems theoretically and experimentally. A theoretical model was implemented using Fluent® software where a jet of variable speed was introduced in a continuous soft matter phase with physical properties similar to those observed in a froth phase in wet and dry conditions. In addition, a simple experimental protocol was designed to validate the model. It was found that the water process jet-like flow influences the behavior of 2 to 3 times the equivalent volume in the froth phase. Such influence zone is dramatically reduced as the froth phase becomes drier. These results were confirmed by the experimental findings indicating that a better froth washing technologies must be assessed and implemented. Some aspects of the ideal froth washing system are derived and discussed in details.

Jan 1, 2014

By Wieslaw Wszolek, Kazimierz Trybalski, Ryszard Tadeusiewicz

"The present work is an attempt of neural networks application to the description of complex technological processes of useful minerals enrichment. Neural networks are among the most convenient tools that have been added recently to the professional toolbox of modelling specialists, and they are particularly useful in realisation of multiple practical tasks, characterised by great complexity and relatively low amount of available a priori knowledge about the nature of the modelled processes. They are successfully applied in a wide variety of problems related to data processing and analysis, their prediction, classification or process control. The object of the study was the technological site for copper ore enrichment by floatation, being a part of technological line in the Ore Enrichment Plant ZG „Polkowice”, KGHM „Polska Miedz” S.A.The main floatation is described by parameters measured by the supervision and control system, which can be grouped with respect to the functions performed for the object:a) input function: aFG - copper contents in the feed material for the main floatation [% Cu]b) control: LFG I - level in the first section of the floatation unit [%], LFG II - level in the second section of the flotation unit [%], LFG III - level in the third section of the floatation unit [%], LFG IV - level in the fourth section of the floatation machine [%]. These quantities compose the five elements long input vector.c) output function: ? - copper contents in the waste from main flotation (final waste) [% Cu]The measurement data, containing the above-mentioned parameters, have been collected during the normal operation of the plant. The data contain momentary values of the parameters, registered every 10 minutes, covering the period of 196 hours of the plant’s operation (1176 measurements for each quantity).For construction of the model used in the study classical multi-layer perceptron-type neural network has been used, with one hidden neuron layer, trained by the error back propagation method."

Jan 1, 2003

By Vladimir G. Kochnev

"Autogenous and semi-autogenous grinding (AG and SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills. However, existing AG and SAG technologies still can be improved and have an immense potential from the viewpoint of economic benefits.Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that comminution in AG and SAG mills can be performed in a more effective way. The company’s approach comprises the following elements:- Novel mill design- New liners and lifters- Novel discharge grid design- Technique of treating material of critical particle sizeA novel mill of the cantilever type capable to operate in the AG and SAG mode has been developed. The cantilevertype mill has a high diameter to length ratio, which dramatically increases the throughput rate, and is characterised by high reliability, fast installation and low capital and operating costs.Tests of the new heel-shaped liners, originally aimed at improving the intact condition of diamond, indicated that they play an important role in the grinding process. Tests performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation, demonstrated that the heelshaped liners provided the increase in the throughput rate varying from 30 to 80 % and the decrease in power consumption in the range 30-55 % for grinding of kimberlite and platinum-containing ores.Investigation of the influence of the main grid parameters on the efficiency of grinding led TTD to a special design of a mill discharge grid, with a radial location of openings, the slot width varying from the periphery to the centre and the grid surface provided with “heels”. The design allows one to control the particle size distribution of the ground product without affecting the grid throughput rate."

Jan 1, 2003

By M. H. Moys, H. Dong

"Discrete Element Method (DEM) has become a standard tool to simulate grinding mills in order to gain information about load behaviour, power drawn, etc. However, parameters necessary to run a simulation are not always readily available. For example, the coefficient of restitution used in DEM simulation from the literature ranges from 0.1 to 0.9 due to lack of accurate values. The lack of correct input parameters results in the fact that some simulation parameters are adjusted to match the simulation prediction with the experimental results. It is inappropriate to tune one single parameter arbitrarily in order to fit the prediction with experimental results. The correct value of parameters for DEM simulation should be established, and rigorous validation on simulation results by DEM needs to be done.The objectives of the ongoing project are to measure the coefficient of restitution at conditions analogous to grinding practice. Equipment has been built to measure the coefficient of restitution. A typical case of impact test showing the vertical position of a ball as a function of time is presented in Figure 1. The coefficient of restitution between steel ball of different sizes and the targets including steel liner (e = 0.91), mild steel block (e = 0.57) and rubber liner (e = 0.7) have been measured. The coefficient of restitution reduces to 0.38-0.52 when there is a layer of coal particles (1-2 mm) on the steel liner. The effects of ball size, drop height on coefficient of restitution are investigated. Then a DEM code is developed of several contact models to simulate the impact process. This code can reveal details on velocities (translational and rotational) and forces (normal and tangential) during the brief impact interval. Figure 2 is a comparison of the rebound rotational velocity between experiment and prediction by different models. The results can be used as DEM input and to assess contact models."

Jan 1, 2003

By Markus A. Reuter, Joep Verwoerd, Marc J. A. Pijnenborg, Yongxiang Yang

"Incineration is a proven disposal technology for all waste materials with heat release potentials, and provides high degree of toxic destruction and control for a broad range of hazardous materials. In the Netherlands, all the hazardous wastes are processed at AVR-Chemie located at the Rotterdam harbour, through rotary kiln incinerators. The newly enforced regulations from the European Union with stricter emission levels require a better understanding of the incineration process and improved process control. However, the transport phenomena and combustion processes within the kiln system are very complex and not well understood. In order to get better understanding of the incineration process, research has been carried out to study the fluid flow and combustion behaviour of the incineration system. Computational Fluid-dynamics (CFD) was used to simulate the gas flow and waste combustion process, and temperature measurements of the operating rotary kiln incinerator were conducted to validate the CFD model. This paper will present the latest results from the current research project for simulating gas flow and combustion heat transfer for a wide range of hazardous waste streams.The simulation of the waste incineration process was carried out using a general-purpose CFD code Phoenics. The rotary kiln and the secondary combustion chamber (SCC), with a waste processing capacity of 50,000 ton/y and an energy input of 30 – 40 MW, is translated into a CFD model. The model includes a k-e turbulence model and a global gas-phase combustion model (3-gas or 7-gas combustion model). The 3- gas model (Simple Chemically-Reacting System, SCRS) predicts only the thermal effect of the fuel combustion, and only one global fuel is used, therefore, real chemical species are not taken into account. In the 7-gas combustion model, (an Extended SCRS, ESCRS), different forms of waste fed into the incinerator have been modelled into a mixture of a general hydrocarbon fuel C3H4 and other components such as CO, CO2 and H2O. Thus, all the incoming fuel streams with different compositions and calorific values can be properly converted into separate inlets. The combustion of the waste is assumed to take place only in gas phase in two steps: (1) primary combustion of the main fuel component C3H4 to form CO and H2, (2) secondary combustion of CO and H2O to form CO2 and H2O. The rate of each combustion reaction is assumed to be controlled by turbulent mixing of fuel and oxidant (air or oxygen), i.e. the Eddy-Break-up (EBU) model. The resulted temperature field was validated with temperature measurement data, and the simulated temperature distribution from both 3-gas and 7-gas model have reasonable agreement with the measured data."

Jan 1, 2003

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone, has been successfully tested in the Platinum industry for dealing with the dense chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine chromite component in the final product. The dense media effect caused by a high chromite concentration in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size material in the float feed. The fine barren particles of chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.With the three-product cyclone a middlings product has been extracted that has a higher concentration of fine chromite. This volumetric stream flow represents a small percentage of the total cyclone feed and it is thus possible to treat it separately via fine screening to remove the fine chromite from the system and recover coarse silica."

Jan 1, 2003

By A. N. Zagorodnyaya, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva, A. S. Sharipova

"In Kazakhstan, there is a unique sulphide copper deposit, in the ores containing the natural isotope of osmium-187 (more than 90 %). In the pyrometallurgical processing of concentrates for the target metal, osmium is mainly sublimated, with wet cleaning of metallurgical gases (dust and gas mixture) 40 % of it together with rhenium passes into washing solutions (wash acid). On the basis of this acid, the production of ammonium perrhenate was organized at the enterprise of the RSE ""Zhezkazganredmet"" and for the first time in the world practice - the isotope of osmium-187. However, the degree of its recovery from solutions does not exceed 8 % of the amount supplied with the charge or 25 % of the amount that was received for extraction. But the bulk of it (~ 75 %) remains in the raffinate, discharged to sewage treatment plants (wastewater). The studies presented in this work are aimed at solving the problem of osmium isotope-187 extracting from wastewater, which are a potential source of increasing metal production in Kazakhstan. The aim of this work is the development and scientific justification of osmium deposition regimes from wastewater using such reagents as thiosulfate and sodium sulphide. The influence of various physicochemical factors on the precipitation of the osmium was studied and optimal conditions for its maximum transition to sediment were chosen. An original method for obtaining osmium concentrate in the presence of sodium thiosulfate with the addition of potassium iodide from a new type of wastewater - man-made ammonia solutions has been developed. These solutions were combined mother liquors of solid-phase stripping operations and dissolution of pulp of crude ammonium perrhenate. On the basis of the obtained results, a settling technology for extraction of the osmium from man-made ammonia rhenium-containing solutions was introduced at RSE ""Zhezkazganredmet"". It should be noted that the degree of extraction of osmium, depending on its concentration in solutions entering on the settlement, and taking into account the addition of sulfuric acid, will vary from 60 to 90 %. The recovery of osmium during the test period was 58 %."

Jan 1, 2018

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of grinding conditions on galena flotation and galena separation from pyrite. The changes occurring on the mineral surface during grinding were investigated by EDTA extraction and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the type and amount of oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite flotation but had little effect on galena flotation. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled.Grinding conditions had a large effect on the flotation of the galena particles of different sizes. Flotation of fine galena particles (-10 µm) was depressed by iron oxidation species derived from the grinding media. Chromium grinding medium decreased the production of iron oxidation species and therefore increased the flotation of fine galena particles."

Jan 1, 2003

Gold thiosulfate complex is difference with gold cyanide complex, which is easily adsorbed on activated carbon while gold thiosulfate complex cannot be satisfactorily recovered by activated car-bon. However, Gold thiosulfate could be recovered by activated carbon if cyanide is added into the thiosulfate solution. To avoid the cyanide solution, this paper will review several possible processes to recover the gold from thiosuldate solution: such as the cementation with metals, ion exchange resin and solvent extraction. The gold cementation with the powders of zinc, copper, iron and aluminium will be discussed. The advantage and disadvantage of each are compared. The consumption of thiosulfate and copper and feasibility of solution recycling will be discussed. The gold recovery by some ion exchange resins will be suggested. The processing conditions, its applications and the resin elution methods will be presented. The gold recovery by using solvent ex-traction will be reviewed. The processing conditions of solvent extraction process are discussed and compared.

Jan 1, 2014

By Tasuma Suzuki

Electrokinetic/permeable reactive barrier system is a promising in situ soil and ground water remediation technique to reduce toxic NO3- into less toxic NH4+. Using granular zero-valent iron (Fe0) as a reductant, the first objective of this study was to investigate the influence of the solid-liquid ratio and aqueouspHon NO3- reduction. The results obtained from a series of batch experiments showed that NO3- reduction was enhanced by either increasing solid-liquid ratio or decreasing aqueous pH. Based on insights obtained from batch experiments, the second objective of this study was set to design the remediation conditions of the electrokinetic/Fe0permeable reactive barrier system to maximize the NO3- reduction efficiency. Experimental results showed that the effectiveness of the system strongly depended on the Fe0 percentage in the reactive barrier, the pH in the anode reservoir, and the applied voltage, which were consistent with the results obtained from batch experiments. Under optimized treatment conditions, nearly 100 % NO3-was reduced into NH4+ in the permeable reactive barrier and collected in the cathode reservoir. Insights obtained from this study provided fundamental information on roles each of remediation design parameters plays, and will be useful to optimize the remediation conditions. Keywords: electrokinetic remediation, permeable reactive barrier, zero-valent iron, nitrate

Sep 1, 2012

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By F. Xie

Low gold and silver leaching kinetics has been commonly observed in traditional gold-silver cyanidation process, especially in those heap-leaching operations. The reactivity and availability of oxidant was believed to be the critical limitation for gold and silver dissolution. The occurrence of silver sulfide such as acanthite (Ag2S) in the ore may also result in low overall silver extraction. Leaching of gold and silver sulfide in the ferricyanide-cyanide solution has been investigated through rotating disc tests and the assistant effect of ferricyanide on increasing the dissolution rate of gold and silver was noticed. The potential use of ferricyanide as an auxiliary oxidant in gold/silver cyanidation process was proposed based on the results of leaching of gold-silver ores.

Jan 1, 2014

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By N. ??dyanik, Z. Kugukaldinova, O. Mishurina, Y. Glazkova, E. Mullina

"This paper describes the process flow of a selective processing method for acidic mine waters formed in the copper sulfide industry and characterized by a high content of copper, iron, and manganese ions. The proposed method comprises a series of sequential processes: the 1st stage is the recovery of Cu2+ ions by precipitation, the 2nd stage is the recovery of Fe2+ and Fe3+ ions as a dispersed phase by acid-base precipitation, followed by recovery in the 3rd stage of Mn2+ ions by converting Mn2+ with an oxidizing agent into insoluble forms of manganese and subsequent recovery of the dispersed phase by electroflotation. The developed method was tested on the acidic tailing storage facility (TSF) water of a mining project in the Urals region. The practical results of the implementation of the developed method have shown that its implementation will allow to recover copper, iron, and manganese in the form of salable products with a simultaneous decrease in their concentrations in adjacent water bodies down to the applicable MPCs. The process is a simple one, does not require any sophisticated expensive equipment and can be implemented either as a standalone solution or as part of existing treatment facilities. INTRODUCTION As a result of unsustainable utilization of natural resources in Russia, only a small fraction is processed into commodity products, while the rest is systematically dumped as emissions, effluents, and other wastes, polluting the environment. By amount of waste and concentration of valuable components, those wastes can be classified as aqueous technogenic resources [1, 2]. Therefore, the development of processing methods for this mineral resource category is an urgent and priority task that will significantly improve the industry’s profitability and the environmental conditions in the respective regions. MATERIALS AND METHODS Following research methods were mainly applied in this study: lab-scale and pilot-scale tests in a diaphragmless two-chamber electric flotation cell; for solutions and recoverable process products — chemical analysis using photometric determination techniques for metal cations and atomic adsorption determination techniques for the processing products. The phase composition of the precipitates formed in the process was investigated by X-ray phase analysis in the general-purpose diffractometer with a copper anode DRON-1."

Jan 1, 2018

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003

By Zhou Yucai, Zhou Jing, Zhu Yimim

"In this article, research on the beneficiation process for a carbon containing copper-molybdenum deposit in Henan province has been carried out. The elemental composition, mineral composition and relative content, characteristics of embedded and symbiotic relationship, the forms of the copper-molybdenum particlesand their disseminated features, and particle size distribution have been worked out. Flotation behavior of copper-molybdenum mixed flotation and separate flotation in the systems of different collectors and depressants, and the influence of different flowsheets on the copper-molybdenum separation have been investigated by actual ore flotation tests, The separation problem of copper-molybdenum for a carbon-containing copper molybdenum ore has been solved.INTRODUCTION In this paper, technological mineralogy, small experiment of flotation recovery of copper Molybdenum ore, and expansion experiment of mineral recovery of copper Molybdenum ore are introduced. (1) The results of process mineralogyshow that the content of copper is 0.42%, molybdenum is 0.021% in the raw ore, they mainly exist in the form of sulfide, with low oxidation rate. (2) The results of flotation tests show that the combination of butyl xanthate and isopropyl ethylthionocarbamate reagents is effective collector of copper-molybdenum mixed flotation for carbon copper molybdenum, (3) When the grinding fineness is -0.074 mm taking 71%, and regrinding fineness is -0.038 mm taking 85%, the flowsheet of first copper-molybdenum mixed flotation and then regrinding rough concentrate and last separation flotation of copper and molybdenum was adopted, which realized the effective separation of copper and molybdenum for carbon-containing copper molybdenum ore. Good flotation indexes were gained with copper concentrate containing 20.96% copper and copper recovery 90.06%, and molybdenum concentrate containing 46.78% molybdenum with molybdenum recovery 72.68%. (4) The seven days average concentration index of scale-up the continuous dressing experiment is as follows, the copper content in copper concentrate is 20.16% and the recovery is 89.61%; the molybdenum content in molybdenum concentrate is 24.58% and the recovery rate is 74.09%."

Jan 1, 2018

By C. H. Veloso

"Starch is the most widely used depressant in the reverse cationic flotation of iron ores. There is however, an indication from recent studies, that other polysaccharides may successfully replace them. When starches are used in the flotation of iron ores in the presence of quartz as gangue mineral, their strong adsorption on the surface of iron oxides can be explained by the molecular conformation between the available sites on the mineral surface and two hydroxyls of starches. However, when the gangue minerals are iron-bearing silicates, the strong interaction with starch can occur on these minerals since they have the same surface behaviour as iron oxide. In this work bench scale tests were conducted in order to generate scientific knowledge about other alternatives depressants for the flotation of iron ores. A magnetic pre-concentrate from a skarn iron ore processing plant was used as feed material for flotation tests. The reverse flotation approach was used to upgrade the iron content by removing complex ironbearing silicates. The depressants used in this study were: corn starch, dextrin, carboxymethyl cellulose (CMC) and humic acid. The tests were performed under different pH conditions in order to try to relate the efficiency of depression to the pH used during flotation. The results show the important role of pH as each depressant reached its best performance at different pH values. At alkaline pH the corn starch showed best depression performance while the humic acid is more efficient at pH close to neutrality.INTRODUCTIONIron corresponds to approximately 6% of earth’s crust composition (McDonough and Sun, 1995). It is the most used metal in our lives, some of its properties as resistance and facility to be shaped makes is replacement very difficult. The primary sources of iron on our planet are minerals. The iron-bearing minerals most commonly found in nature and economically exploited are magnetite [Fe3O4], hematite [Fe2O3], goethite [FeO(OH)] and siderite [FeCO3] (L O Filippov et al., 2014). These minerals are commonly associated with other minerals (most of the time not economically exploited) forming the so-called iron ore. Iron ore is the source of primary iron for the world’s iron and steel industries."

Jan 1, 2018

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By Dilip. Makhija, Asim. K. Mukherjee, Tamal Ghosh, Abhay Patra

In India around 15-20% of Run of Mine (ROM) from any iron ore deposit reports to slime dams as byproduct of iron ore beneficiation process. The proportion of iron ore slime to ROM will increase in future with higher proportion of lean grade ores in ROM. Furthermore, tonnages of iron ore slime will also increase with increasing demand of iron concentrate. Presently, this slime is stored in the dam in the absence of beneficiation technology. A beneficiation flowsheet has been developed at Tata Steel. This process produced concentrate of 2.2% alumina with 40 % yield from slime of 7-9% alumina. The iron content in the reject will be less than 40% thus adhering to the regulatory norm. Pilot scale study show waste from slime beneficiation is a good raw material for making a variety of building materials. Waste from slime beneficiation also has soil amendment properties. Pilot scale studies show productivity of rice increased when the waste of slime beneficiation process is mixed with soil. On commercialization of this zero waste technology slime generated from the iron ore washing plant will be completely used. In this paper the result of the pilot scale studies on slime beneficiation and utilization processes towards soil making and making of building materials are discussed in detail.

Jan 1, 2014