Search Documents

By A. M. Ozbayoglu

Gross calorific value (GCV) of coals was estimated using artificial neural networks, linear and non-linear regression techniques. Proximate and ultimate analysis results were collected for 187 different coal samples. Different input data sets were compared, such as both proximate and ultimate analysis data, and only proximate analysis data and only ultimate analysis data. It was observed that the best results were obtained when both proximate analysis and ultimate analysis results were used for estimating the gross calorific value. When the performance of artificial neural networks and regression analysis techniques were compared, it was observed that both artificial neural networks and regression techniques were promisingly accurate in estimating gross calorific values. In general, most of the models estimated the gross calorific value within ±3% of the expected value.

Sep 1, 2012

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

"Russia is among the nations holding the world's largest lithium ore reserves. Lithium is of key importance for the global economy. Therefore, it is important to review the current state of technology research aimed at finding the most effective solutions for the recovery of lithium from promising reserves in Russia. In Russia, a number of process solutions for the flotation of spodumene into salable concentrate (5% Li2O) have been implemented at the earlier existing complex low-grade ore concentration project. By applying these solutions, a sample of high-grade spodumene ore (4.7% Li2O) of the Greenbushes deposit was processed into a spodumene concentrate (7.5% Li2O) at a high recovery (~93%) of lithium. In Australia and Canada, new processes have been developed for the recovery of high-grade spodumene concentrates from high-grade ores using dense medium separation and flotation. For the recovery of mica lithium concentrates from low-grade ore, a flotation process was developed in Russia using the cationic collector ANP-2 and Oxifos-B as an additional collector. Low-grade ore containing 0.14% of lithium oxide was processed into a 2.7% Li2O concentrate. New hydrometallurgical lithium concentrate and ore processes are developed to avoid high-temperature (>1000 °C) roasting. The Sileach process (Australia) includes leaching of lithium ore with sulfuric acid in the presence of a halogen-containing component at a temperature of 95-115 °C. In the Russian process, lithium is recovered into an alkaline solution from low-grade spodumene ore in a pressure alkaline leaching environment (250 °C, NaOH concentration > 300 g/l). The developed concentration and hydrometallurgical methods will allow to design on their basis efficient processes for recovering salable products for hi-tech industries from lithium ores.INTRODUCTION Lithium has many unique and important properties. It is the least dense hard metal. Its alloys have some of the highest strength-to-weight ratios. Lithium has the lowest melting point of all known solid elements and is used as a highly-effective heat transfer medium. The high demand for lithium is due primarily to its unique electrochemical potential and low thermal expansion coefficient. It is used in the production of glass and ceramics, in petrochemicals, metals, medical and other industries. Since the late 20th century, the electronics industry has been the largest consumer of lithium. In recent years, lithium has attracted much attention also as an important component of ultra-lightweight electronic devices. It is also the preferred metal for electric batteries used in mobile electronic devices, vehicles, household power generators, making it an important resource for the development of environmentally friendly technology. Leading automotive brands have ambitious plans for the production of electric cars — Tesla Motors, VW, Toyota, GM, BYD Auto. It is expected that the production of electric vehicles alone will triple the demand for lithium by 2025. A sharp increase in the production of lithium is expected. Lithium has all the prerequisites to become a strategic resource of the 21st century. (Deutsche Bank, 2016; Bradley et al, 2017)"

Jan 1, 2018

By W. Y. Liu

A sulfate reducing bacteria strain (named SRB-A) is isolated from sanitary wastewater by using anaerobic technology of Hungate. The studies of physiological, biochemical and phylogenic of the isolated strain are carried out. The colonies of the strain are circle. Cells that are slightly curve, rod-shaped with the size of 1.0~3.0µm in length and 0.8~1.0µm in width. The optimum temperature for growth of the organism is 30~35°C. The optimum pH for growth is 7.0~7.2. Strain SRB-A can use sodium lactate, sodium citrate, sodium acetate, ethanol and acetone as electronic acceptor but can not use glycerol, glucose, sucrose and sodium oxatate. The isolated strain reduces sulfate, sulfide, sulfur, DSMO and FeCl3, then nitrate and nitrite can not be used. The strain has higher tolerance of NaCl, and the optimum growth occurs in the presence of 5%~8% (w/v) NaCl. The result of 16S rDNA sequence analysis indicates that the isolated strain SRB-A is the most similar to Desulfo-vibrio halophilus, and the level of the similarity was 98.4%. The isolated strain has a stronger ability to reduce sulfate, and the level of sulfate reduction reaches about 90% at pH 7 in the liquid medium. 0.6 to 0.8 is the optimum COD/SO42- in the medium for the isolated strain to show better ability to reduce sulfate. At pH 2.5 the level of removal of Cu2+ reaches 96.3%. Under the condition of pH 3.5, the level of removal of Zn2+ reaches 92.6%. When the value of pH reaches about 7, the Fe3+ is precipitated by the formation of Fe(OH)3, and Fe3+ is removed up to 89.4% at last.

Jan 1, 2014

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By A. S. Choudhary

Most of the coal reserves in India are of drift origin and have very poor washability characteristics and a high level of near gravity materials. At least 30 new coal wash plants are expected to be set up in the next 5years.In such a scenario, adequate sampling followed by sink float test work for washability analysis becomes very critical for designing these new plants. For coal sampling purpose, stipulations of different standards are sometimes formidable and on the border of ?impracticality?; sometimes are self contradictory in terms of gross sample weight vis-a-vis minimum number of particles required in each size fraction and in each relative density fraction and also the minimum mass in the latter. Validation of the generated data is another important aspect of washability analysis. These issues can easily be addressed by using straight forward mathematical relationships, well known RR plots and by using simple MS Excel tool, etc.

Sep 1, 2012

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012

By B. Vasanthakumar, H. Ravishankar, S. Subramanian, J. Braun

The flotation of sphalerite and galena in the presence of intra- and extra-cellular components isolated from Bacillus circulans before and after adaptation to the chosen minerals has been studied. Based on various biochemical treatments, the key biomolecule primarily responsible for the flotation of sphalerite has been identified as DNA, which functions as a bio-collector. A noteworthy finding is the considerably higher flotation recovery of sphalerite obtained in the presence of single stranded DNA (79.8%) vis-à-vis double stranded DNA (50.2%). Selective flotation tests using the soluble fraction obtained after thermolysis treatment highlight that sphalerite-adapted cells yield a higher selectivity index (S. I.) of 31.2 compared to galena-adapted (S.I. 4.3) or unadapted (S.I. 12.2) cells. During bacterial adaptation to the above chosen minerals, the quantitative and qualitative changes in the surface potential, surface morphology and cell wall components have been monitored. The prior adaptation of the bacteria to sphalerite results in the secretion of a higher amount of proteins, eDNA and phosphate, whereas adaptation to galena leads to a higher amount of polysaccharide, uronic acid and acetylated sugar, vis-à-vis the unadapted bacteria. A significant observation is that the bacteria undergo a change in morphology from rod to sphere as a strategy to resist metal toxicity during adaptation to galena. Interestingly, this phenomenon is not observed during bacterial adaptation to sphalerite. This morphological transition has been shown to involve changes in crucial cell wall components as well as changes in the levels of expression of bacterial cytoskeleton element mreB gene involved in the maintenance of the rod shape. The sequence of B.circulans mreB gene has been identified using Polymerase Chain Reaction (PCR) followed by DNA sequencing.

Jan 1, 2014

By B. Q. Xiao

In surfactant flooding, surfactants added are often a mixture of the same type of molecules with different lengths of carbon chains. The relationship between a single, pure surfactant solution and crude oil is seldom studied. Additionally, up to now, alkylbenzene sulfonates are applied widely in surfactant flooding, such as Daqing oilfield, China. A factory producing alkylbenzene sulfonates will enlarge its yield to 20 000 tons per year over there. For the purposes of widening the alkylben-zene sulfonates? application, 16 kinds of pure alkylbenzene sulfonates were synthesized through Friedel-Crafts acylation and Wolff-Kishner reduction reactions, and the compounds? molecular structures were confirmed by 1HNMR and 13CNMR spectra. The factors affecting interfacial tension (IFT), such as, surfactant type, oil composition, electrolyte concentration, and alkali concentration were considered. The synthesized pure surfactants? critical micelle concentration (CMC) and optimal salinity were measured through interfacial tension technique. According to lab experiments results, heavy alkylbenzene sulfonate (2SY) was synthesized in magnifying scale in Jinzhou Wash Chemical Plant and the coretests were conducted using it. The results showed that the homemade heavy alkylbenzene sulfonate (2SY) flooding can improve oil displacement efficiency 20% more than water flooding at surfactant?s concentration from 0.05%(wt) to 0.2 %(wt).

Jan 1, 2014

By E. Barsky

Physical principles of two-phase flows with a polyfractional solid phase have not received a sufficient theoretical interpretation as yet. Two-phase flows in the separation mode with a counter-flow of particles are even more complicated. Only statistical methods give an insight into general regularities of such processes. These processes can be interpreted best by analogy with the statistical model of an ideal gas developed by L. Boltzmann, although here a number of difficulties arise. The notion of a statistical system for such flows is substantiated. A mathematical estimation of a statistical system is presented. New notions are introduced, namely, potential extraction of a system and lifting factor. A relationship having the physical meaning of entropy is derived for a two-phase flow in the separation modes. The connection of this new entropy with flow parameters, such as the number of particles, separation factor and chaotizing factor, is established. Properties of this entropy are analyzed, as well as the analogy and difference between this entropy and Boltzmann?s entropy. The notion is formulated and the definition of the chaotizing factor of a process is suggested. In the framework of a statistical approach to two-phase flows in the separation mode, the notion of flow mobility has been formulated. Principal regularities of mass transfer in zone/apparatus sys-tem are analyzed. Principal ideas of a cellular model of the process are formulated, and main relationships for its description are derived. Proceeding from the cellular model, a dependence describing the degree of fractional separation of a narrow size grade is found. The analysis of this dependence makes it possible to reveal the crucial role of the Froude criterion for gravitational separation processes. It is found empirically that this parameter is a basis for the affinization of separation curves (Barsky E, Barsky M, 2006; Barsky, 1980).

Jan 1, 2014

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

By Kari Niiranen

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. The largest of the apatite magnetite deposits and the mines are Kiirunavaara with annual production rate of approximately 27 Mt crude ore underground. LKAB produces two varieties of pellets: blast furnace pellets and direct reduction pellets (LKAB DR Oxide Pellets). Meanwhile the concentration process in a sequence of the low intensity magnetic separation (LIMS) and flotation at the concentration plant. In spring 2007 there were noticed great fluctuations of SiO2 grade in the crude ore. The high SiO2 grade is particularly problematic in the case of direct reduction pellets. In consequence, a project was started (called Silica in the Mine) to define exactly the problem related with silica and to find out, if possible, the reason for the great fluctuation of SiO2 grade in the crude ore going to the processing plant. A further target of this project was to develop a simplified method at the laboratory scale, to predict SiO2 grade in the magnetite concentrate in the future, but also predict the physical properties of the ore with respect to mineral processing. The essential stage of systematic characterization of the ore body for mineral processing properties is the estimation and simulation of different parameters from the laboratory scale to the large scale at the concentration plants using empirical data collected at the mineral processing by LKAB in Kiruna. Further a target was also to find useful physical parameters for mineral processing and implant those parameters into the existing geological 3D-model of the deposit. This information will be used for making prognosis of the future mining and the quality of the crude ore. It will also give better control and improve the production planning in the mine and the performance at the concentration plant in Kiruna concerning the decrease of the SiO2 grade of the magnetite concentrate.

Sep 1, 2012

By T. Tumidajski

The purpose of the separation processes in coal processing is obtaining products of certain ash contents. In the most of cases it is assumed that the separation process is described by one, selected parameter, which usually is grain size or material density. The separation may be described by means of statistical distributions of random variables, what allows forecasting the separation results of certain enrichment method. There are very well known the applications of approximations of Tromp separation curves or distribution functions of Erasmus, Meloy or Weibull. It is necessary to say that if the fitness of the approximation more suitable, then the characteristics of the process itself is also better. In purpose of obtaining more appropriate results, these methods were modified by application the mathematical functions, as i.e. hyperbolic tangens function. Furthermore, on the basis of empirical data, so-called interpolations may be performed in purpose of getting more appropriate results of approximation. One of the most known techniques of interpolation is Hughes method. This method for interpolating standard data involves breaking down each interval into a number of smaller sub-intervals. The results of such one-dimensional approach not always contain the full in-formation of the searched distribution. It happens because such interpretation of the problem is not completely correct. In practice, the separation process depends not only on the one parameter (i.e. grain size), but also on many other features characterizing certain material (i.e. its density). It seems then that in some cases the application of multidimensional grain characteristics distributions will be more appropriate. In this paper, the technique of joining the distributions of grain size and density by means of so-called Morgenstern distributions is shown. The general form of these distributions is as following:

Jan 1, 2014

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012

By Kaustubh Joshi, Pradip, Beena Rai, Venugopal Tammishetti

"Rapid depletion of high grade iron ores coupled with the increasing demand for the blast furnace grade iron ore in recent times has shifted the research focus on the development of appropriate technologies for the utilization of low - grade alumina rich iron ore slimes. These slimes are currently being dumped into tailing ponds owing to their high alumina content. Typical constituent minerals present in the Indian iron ore slimes are hematite, goethite, gibbsite and kaolinite. Considering the fine particle size distribution (<37 microns) in the slimes, selective dispersion-flocculation seems to be one of the most appropriate process which has been explored by us. We present our successful results on a natural iron ore slime sample obtained from one of the mines in India. We have been able to achieve a concentrate assaying >67% Fe, and <3% Al2O3 and 2.8% loss on ignition (LOI) from the slime sample assaying 60.4% Fe, 7.7% Al2O3 and 5.45% LOI with an Fe recovery of 62-69% simply by adjusting the pulp pH. We have scaled up the process to a semi batch scale as a prelude to commercialize it for the beneficiation of low grade iron ore slimes."

Jan 1, 2014

By W. L. Jiang

Reverse-flotation technology is often applied in iron ore dressing plant, in order to enhance the quality of iron concentrate from magnetic separation. However, this technology has disadvantages in operating cost, energy consumption, and environmental protection. Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate. This paper describes the development of Complex Flashing-Field Magnetic Cleaner, a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field. This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magnetic field, which can strengthen the formation of magnetic agglomerations and the dispersion of gangue minerals, improving the quality of separation. The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process. Test results showed that this equipment is reliable in operation, economically beneficial, and has large potential of application.

Jan 1, 2014

By A. T. Adema

The cohesive zone, where the ore fed into the blast furnace softens and melts, is critical to the blast furnace performance and stability due to its influence on the gas and solid flow. This paper de-scribes a project for the development of a process model to predict the cohesive zone properties and the results of its first step; the solid flow model. The process model is expected to describe a realistic solid burden flow and the formation of the cohesive zone, its shape, location, structure, permeability, and in particular the mineralogical changes within the cohesive zone. This will be achieved using various simulation and computing tools: a combination of the Discrete Element Method (DEM) and Computational Fluid Dynamics (CFD), the DEM?CFD hybrid approach, together with models for the thermodynamics and reaction kinetics. The key benefits of the hybrid approach lie in the coupling of the continuous phase and the discrete particles, and the possibility of introducing thermodynamics and reaction kinetics into the system in a more realistic manner. Two DEM simulations are presented for a small scale blast furnace to investigate the influence of non-spherical particles on the solid flow. This influence can be observed from a more even solid flow pattern and a reduced deadman size. The results indicate the requirement to include non- spherical particles in a blast furnace simulation to achieve a realistic solid flow.

Jan 1, 2014

By Shi Shuaixing Zhang Yuejun, Fan Xuesai Zhangming

"For the traditional principle of flotation cell design, or in the perspective of some researchers, the mixing effect of impeller for flotation cell is not only to suspend the particles off the bottom, but also to mix slurry well to achieve a uniform system. But for some special processing conditions, the depth profile of slurry concentration and particle size demonstrates an obvious difference. In the part around of the impeller in the cell, the slurry concentration is much higher than the part below the lip.For the vanadium titano-magnetite flotation process, distinguished with high concentration and large coarse particle size fraction, even though the concentration is very high, it can reach good gas dispersion, which is a fundamental principle for flotation cell design and application. The gas dispersion is not a challenge in the high slurry concentration environment, not only in the vertical direction, but in the cross section. Different levels (the distance from the lip is 400mm, 700mm, 1200mm, 1700mm, 2200mm, 2700mm) slurry in the flotation cell is sampled and analyzed. The slurry concentration of the 3 levels(1700mm, 2200mm, 2700mm) is about 55%, but the slurry concentration decreases from 55% to 25% sharply towards the lip.Therefore, a new understanding and viewpoint is presented, that the uniform system of slurry is not always reasonable for all of the flotation process. For some special process, if the coarse particles are needed to agitated well and transported to the upper cell, the quiescent zone in the upper cell will be destroyed and enhance the detachment probability for the coarse particles. The difference of slurry concentration and particle size fraction benefits the air dispersion and coarse mineral particles recovery.1.INTRODUCTIONNowadays, flotation is the most widely used separation process in the mineral processing industry. The importance of flotation technology in the global economy is significant. A rough estimate of the quantity of crushed ore treated by flotation is about nine billion tons per year, and the portion of base metals processed using this method is approximately 95% (Brewis, 1996)."

Jan 1, 2018

By R. C. Miranda

Artificial vision systems are increasingly used to assist humans to perform different tasks in different areas. These systems are able to recognize patterns in complex images, which can provide multiple data. Currently, vision systems are used in both; monitoring traffic - which uses radars for vehicular plate recognition- as in metallurgical and food industries for strict quality inspections. Their use in mining occurs in measuring the speed of froth over the lip of a cell, in determining the shape and size of pellets, in obtaining from the tendency of mineral content and as a replacement for laboratory analysis of particle size. With this advanced tool, it is possible to achieve significant improvements in quality, productivity, and especially in reducing costs in pelletizing plant of iron ore. The objective of this paper is to contemplate the current situation of image analysis in the pelleting plants and glimpse at the potential applications that are being developed. This paper also presents the conception and implementation of an automatic control system of the pellets size distribution applied on a pelletizing plant of iron ore. The article demonstrates the strategy used for measuring the size distribution of the iron ore pellets, based on image analysis and the strategy implemented on advanced process control, which shows substantial gain on plant performance.

Sep 1, 2012

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012

Much has been published in recent years on the challenges facing the engineer of the 21st century and the consequent challenges facing the education providers and industry. The world is changing rapidly on the social, economic, political, technical and environmental fronts and our metallurgists/mineral processing engineers of the future will arguably need to have a different set of skills than those which were traditionally regarded as adequate during the latter half of the 20th century. This paper attempts to explore some of these issues and their ramifications.

Jan 1, 2014