Search Documents

By T. C. Alex, S Srikanth, Premchand

It has been suggested that reduction of the iron and manganese phases as far as FeO and MnO is preferred for the complete liberation and selective reduction of the copper, nickel and cobalt oxides in manganese nodules. The oxygen partial pressure/temperature regime suitable for this purpose has been delineated. Free-energy minimisation and thermogravimetric results indicate that the requisite conditions can be achieved if more than 10% of neutral oil is used at temperatures greater than 923 degrees C. Neutral oil content, temperature and roasting time have been optimised to maximise leaching recoveries of Cu, Ni and Co: up to 96% of Cu and Ni and up to 85% of Co can be recovered if 15% of neutral oil is used as a reductant at 973 K for 90 min

Jun 21, 1905

By P. H. Morris

Nineteen field trials of the co-disposal of fine coal tailings and coarse coal wastes were conducted at the dual Goonyella-Riverside mine in Queensland and at the Hunter Valley No. 1 and Warkworth mines in New South Wales, Australia. The profiles of and the sorting that occurred on the co-disposal deltas are described and an existing theory of subaerial deposition, originally developed for mine tailings alone, is shown to apply to the co-disposed wastes. This enables the dimensionless profiles of large deltas, which may take years to deposit, to be predicted from data obtained from a small delta formed in a few days or even hours

Jun 19, 1905

By L. Villa, O. Suarez, D. Arias, L. G. Corretge

The deposit comprises two vertical, lenticular bodies emplaced in the allochthonous block of a Variscan thrust. Epigenetic mineralisation occurs as replacement of carbonated volcaniclastic rocks of Cambro-Ordovician age. The dominant sulphide minerals are sphalerite and galena with minor chalcopyrite; the main non-metallic mineral is quartz and there is hydrothermal silicification, chloritisation and sericitisation. Sulphur isotope values for sphalerite and galena are heavy and reflect the fundamental relationship between delta-34S in ZnS and in PbS, suggesting isotopic equilibrium. Four sphalerite-galena pairs yield temperatures between 163 and 218 degrees C, in good agreement with the 187-207 degrees C estimated by the Ga/Ge-sphalerite geothermometer. The ore sulphide was leached by the hydrothermal solution from diagenetic pyrite in the host rocks and disseminated sphalerite and galena in Cambrian carbonates

Jun 19, 1905

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

By R Lastra, J. A. Finch

An artificial standard material has been developed and used to examine the robustness of some of the procedures for correcting stereological bias. Different mineral liberation distributions were constructed from the standard material. The particles were mounted, sectioned and the sectioning data measured with an electron microscope interfaced to an image analyser. Four correction procedures were used and the corrected and true liberation distributions compared. It was found that the large-sections correction provided a simple, uncorrupted correction. Hill's fast approximation performed well except in cases of narrow liberation distributions; the sectioning data appeared to support the assumption that the locked section and locked particle distributions are identical. Barbery's correction performed well in most cases, having difficulty only with the very irregular liberation distribution. The PARGEN correction was able to provide a good estimate of the true amount of free material, but had difficulty in predicting the locked particle distribution

Jun 21, 1905

By J. L. Robson, C. M. Bristow

mass flow rates of particles and air (the loading ratio).

Dec 1, 1994

By J Parnell, B Manson

Bitumen occurs in the basins in reservoir sandstones, in veinlets close to hydrocarbon source rocks, in veins through lava beds and in sulphide-mineralised veins where it is closely associated with, but predates, the sulphides. The role of organic matter was probably in enhancing metal reduction by creating a low-Eh environment rather than in metal transport. Coeval euhedral quartz crystals or albite in sulphide-bearing carbonate veins provide evidence of an aqueous component to the hydrocarbon fluid

Aug 1, 1995

A production drill rig at a site in Sweden was equipped with a monitoring system to estimate production statistics. Drill running times, drill hole depths, penetration rate, rotation speed, thrust, air percussive pressure and torque pressure were recorded for every 10 mm of hole length for a period of 5 months. Operational activities (rock penetration, tube handling, moving and set-up time) accounted for almost 62% of the time consumed, the remaining 38% being different types of stoppage. Drilling itself, as opposed to handling, took less than 24% of the total time. The results give an indication of how the overall drilling capacity can be increased and which activity should be emphasised. The impacts of automation, new developments and reorganisation on production can also be predicted. Average production was found to be around 100 m/day, but varied between 50 and 160 m/d. The company's specification for the drill rig, before purchase, was that an average production rate of 130 m/d be attained over two consecutive months of drilling - a rate which monitoring shows will not be achieved

Jun 19, 1905

By A Cox

It has been demonstrated that all the cadmium from spent batteries, typically 4 g per battery, can be recovered by burning polyvinyl chloride waste to yield hydrogen chloride; this reacts to produce volatile calcium chloride, which can then be condensed and collected in a separate reactor. Alternatively, chlorine may be used to chlorinate the cadmium with equal efficiency. There is also a prospect of using very low concentrations of these gases, less than 1%, to effect the separation. The Cd was recovered more quickly when exposed to sustained, controlled flow rates of chlorinating gases, whereas when PVC was burnt most of the gas was produced in a very short time, not allowing complete reaction. This problem can be overcome by recirculation of the gas into the reactor. The technology is efficient and clean and the equipment used is simple, enhancing the prospects for a pilot-scale version of the process

Jun 21, 1905

By P. H. Williams, D. J. Morris

The co-disposal of coarse and fine coal wastes by combined pumping through a pipeline to subaerial deposition was pioneered in Australia in 1990 by Jeebropilly colliery in Queensland. Significant segregation of fines is found to occur in its co-disposal delta, leading to the formation of distinct mainly coarse upper and fine-dominated lower segments; the upper delta drains rapidly and is able to support traffic on its surface immediately after deposition. An existing theory of subaerial deposition, originally developed for mine tailings alone and later extended to trial co-disposal, is shown to apply also to the upper segment of the full-scale Jeebropilly delta

Jun 19, 1905

By V. A. Melezhik, P. K. Skufin, L. P. Nilsson

these factors into account. Theoretical and

Aug 1, 1994

By B. S. Terry, C. L. Harris

After measuring the kinetics of Ni reduction from a SiO2-saturated fayalite slag into a Cu-based metallic phase on a laboratory scale, a general model was developed that is capable of simulating mass transfer to and from metal-slag, slag-gas and metal-gas interfaces for multiple species. The model was used to simulate the reactions that occur when Cu and Ni are reduced from fayalite-based slags into a Cu-based metallic phase. Good agreement was achieved between model predictions and experimental data

Aug 1, 1995

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By J Kokado, N Hatta, S Yabushita

A theoretical model is described for prediction of the capacity of fines from porous ores, such as cokes and sintered ores, to be removed by a pneumatic, horizontal-type classifier prior to charging into a blast furnace. First, the influence of variation in the apparent density and drag coefficient of porous ores on removal efficiency is analysed from a stochastic standpoint. The effect on efficiency of collisions between particles in the classifying region is then examined analytically in relation to the ratio of the mass flow rates of particles and air (the loading ratio). Finally, a theoretical model is constructed that takes these factors into account. Theoretical and experimental results are compared and classifying efficiency is discussed from both experimental and theoretical viewpoints.

Dec 1, 1993

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

By G. G. Barbante

Anode slimes produced during copper electrorefining are a valuable source of silver, gold, selenium and tellurium. The conventional pyrometallurgical process for treating slimes involves preliminary leaching in sulphuric acid followed by smelting in a reverberatory furnace with fluxes, but it is slow and has many recycle streams. The chemistry of the phases and the reactions that occur in slimes smelting are poorly understood and and this prevents major improvements to the process. Laboratory-scale experiments were conducted using unleached slimes, with and without the addition of fluxes and under neutral, oxidising and reducing conditions. Results show that selenium is readily removed as gaseous selenium dioxide and that molten Cu-Ag-Se-O phases form when fluxes are added. Oxidation-refining of these phases by air injection and flux addition can result in the formation of silver suitable for further electrorefining

Aug 1, 1995

Carbon anode cells were studied by two-dimensional computer simulation to evaluate their suitability for alumina electrolysis at high superficial current densities. The most efficient anode arrangement was needed to overcome the electrochemical disadvantages of alumina's low solubility in chlorides. Cells with packed-bed anodes might provide practical superficial current densities greater than 0.67 A/cm2 when the granule size was less than 1 cm, but in the process of electrolysis the granules within the active zone would be consumed and become smaller, affecting alumina concentration transport. For zones of very small granules a concentration-dependent model should be considered; for more complete consideration a time-dependent model can be introduced to describe the variation of granule size and its influence on mass transfer and polarisation

Jun 19, 1905

By S Colak, M Tunc, C Celik, M. M. Kocakerim

The most important parameters affecting the solubility of ulexite (sodium calcium borate) in H2SO4 were found to be reaction temperature and solid:liquid ratio, in that order. Dissolution increased with increase in temperature and stirring speed and with decrease in solid:liquid ratio, particle size and acid concentration, the last effect as a result of decreased precipitation of CaSO4 on unreacted particles. Optimum conditions, in which around 99.5% of the ulexite could be dissolved, were a reaction temperature of 60 degrees C, a solid:liquid ratio of 1:8 g/ml, an acid concentration of 8 mol/l, particle size smaller than 425 micrometres, a stirring speed of 52.33/s, a reaction time of 1 800 s, a calcining time of 3 600 s and a calcining temperature of 170 degrees C. These conditions, determined by the Taguchi method, are reproducible in a commercial production environment

Jun 21, 1905

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996