Search Documents

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft (305 m). At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. T

Feb 1, 2020

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks

Feb 1, 2020

By T. Szendrei, S. Tose

This paper will review several flyrock incidents that occurred recently in the South African mining industry to highlight that potential difficulties of the historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques. These process are not capable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. (Approximately 500 ft.) Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study for the explosives industry. In this paper we use the trajectory model to identify certain conditions on the bench whereby the impulse of gas pressure acting on fractured material on or close to a free face is enhanced, resulting in a greater transfer of momentum to potential flyrocks.

Jan 1, 2024

By Peter Moser, Andreas Grasedieck

In modern rock blasting it is becoming more and more important to achieve a certain specified fragmentation. This means that the rock particles formed as a result of the blast should conform to a desired particle size distribution. An important issue with respect to achieve a desired blast result in terms of fragmentation is both the availability of models for the prediction of the characteristic of the particle size distribution of blasted material and the determination of the energy necessary to achieve a certain fragmentation status. Within the research project “Less Fines” funded by the European Union under project reference G1RDCT200000438, the latter has been addressed by the Department of Mining Engineering& Mineral Economics of the University of Leoben. For that purpose fragmentation results from lab scale blast tests have been analyzed and the relationship between the specific charge used for the blasts and the resulting specific surface of the fragmented material has been examined. Linear relationships between the specific charge and the specific surface of the resulting fragmentation were found for various types of rocks to apply over a range of 10 for the powder factor.

Jan 1, 2004

By Lauren Shields

This paper discusses the application of current fragmentation models for underground blasting, establishes a conceptual fragmentation model for underground operations, and discusses the applicability of the mine-to-mill approach for underground blasting. Additionally, this paper also discusses selected case studies where the mine-to-mill approach is applied to underground mining operations.

Feb 1, 2020

By Andre Koekemoer, Gys Landman

At the moment, electronic initiation is migrating from a position of a specialist niche to that of a more widely applied technology. Ease of use and deployment rate are becoming aspects of greater concern for end users.

Jan 1, 2011

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft(305m).At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. The components of the flare involved in the accident were inspected via x-ray and microscopic imaging techniques, and compared with those of unfired flares recovered from the same vessel. Chemical analysis of residue on recovered components from the accident flare was also performed. These comparisons were used to determine the likelihood that the actuation mechanism had been deliberately manipulated. In the subject model of the flare, ignition of the rocket motor is accomplished through a percussion cap which is struck by a firing pin. Prior to activation, the firing pin holds down a pre-compressed spring. We present a comparison of the ignition system of the incident flare with those of other rocket parachute flares, which do not incorporate any stored mechanical energy.

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By Ulrich Leiste

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By M. Khaled, K. Abdel Rahman, M. Khattab

Helwan limestone quarry is located at a distance of 35 km (21.7 miles) to the south of Cairo downtown. Drilling and blasting operations are used to extract the limestone for the Helwan Cement Company (HCC). In 1980’s a new urban community was constructed adjacent to the quarry. This situation led to shifting of the old quarry 5.0 km (3.1 miles) to its current location, to avoid causing blasting problems to the new community. Unfortunately, the new quarry is opened in a highly faulted area, with weak zones of brittle materials. The drilling and blasting crew is facing many difficulties due to the geological complexity along these zones. Moreover, the extension of this community towards the new quarry makes the control of ground vibrations is very important.

Jan 1, 2008

By M. Szumny, P. Mertuszka, K. Fuławka

Multi-face destress blasting is the basic method of reducing rock bursts hazard in Polish copper mines. Blasting operations of this type are carried out regularly, twice a day in order to minimize the geomechanical threat while maintaining high extraction efficiency. Unfortunately, the assessment of the effectiveness of this type of work until recently was based solely on determining whether a given destress blasting triggered a seismic tremor or not. Information on the characteristics of seismic waves generated by blasting has so far been omitted in analyzes of this type. The lack of reliable knowledge about the generated seismic effect makes the introduction of constructive corrective actions impossible, which in turn significantly reduces the triggering potential of conducted destress blasting. This study presents the results of comprehensive work aimed at increasing the effectiveness of active rock burst prevention in Lubin underground copper mine. For this purpose, an innovative system for continuous monitoring of seismic waves induced by multi-face blasting was developed, and a new method for seismic assessment of the effectiveness of the destress activities was developed. Based on the monitoring data and the comprehensive analysis of waveforms, the effectiveness of individual blasting operations was determined, and on this basis, modifications to the drilling and blasting patterns aimed at increasing the generated seismic effect were proposed. The use of innovative methods of monitoring and data analysis made it possible to increase the effectiveness of the conducted activities, in terms of the magnitude of seismic vibrations, up to 250%. It should be emphasized that the introduced modifications were aimed at increasing the effectiveness of blasting operations while maintaining the current level of costs. As a result, the proposed solution turned out to be highly effective, significantly affecting the safety of the work carried out in Polish copper mines. Thus the proposed approach is planned to be implemented in other Polish copper mines belonging to KGHM in the near future

Jan 1, 2024

The quiet banks of the Maumee River in Toledo, Ohio, received a wake-up call July 16 as two smokestacks in the Marina District were leveled with dynamite. B&B Wrecking, Inc. of Cleveland contracted the project with the city to bring down the twin stacks, both measuring over 250 feet tall. The structures were part of the Toledo Edison Steam Plant and were erected nearly a hundred years ago. A week’s worth of preparation went into final planning, drilling and loading holes with over 80 pounds of explosives. The felling went precisely as planned as onlookers cheered as the stacks were reduced to rubble.

Jan 1, 2015

By Peter Moser, Mark Ganster, Radoslava Ivanova, Florian Bauer

Blasting accurately in underground drifts and creating a smooth contour requires proper drilling, knowledge about the apparent geology, a well designed blast pattern and ideally a smooth blasting product. These products are usually cartridged explosives with less energy and are charged in the contour holes in order to reduce the energy concentration and therefore the cracking into the surrounding rock. With the development of a new contour blasting system, a device can now be delivered to the industry that that avoids the additional storage of cartridged products when bulk explosives are used. The system consists of a foldable hose that is charged with bulk emulsion, in the same way as the rest of the blast, from the base to the collar of the hole. It centers automatically in the borehole and provides a decoupled charge. The paper describes the system in detail, gives background information on smooth blasting and presents the first successful field tests using the system in the drifts of an underground mine. It shows the advantages of blast results that produce more stable contours that reduce the amount, time and cost for support but also increase safety underground.

Jan 1, 2012

By Steven Putt

The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

Feb 1, 2020

By Muhammad Yamani, Marsell Riviera, Herry Saputra, Rizky Amin

Drill and Blast processes in hot and reactive ground conditions are a severe challenge in mining, especially in the blasting process. Our main objective is safety issues without compromising the blasting outcome. Safety concerns include unexpected detonation, product damage, and misfire. However, apart from the issue of blasting safety, it is also crucial to maintain good results such as fragmentation, loader productivity, and ore dilution control. Therefore, we use a different product selection method to produce a safe and efficient blast. Pit Araren is one of the pits of the Tokatindung Gold Mine Project in North Sulawesi Province, Indonesia, classified as hot and reactive ground conditions that range from elevation of 25mRL temperature could reach to 98⁰C (208,4⁰F) based on actual measurement. The previous practice for blast holes with temperatures above 70⁰C (158⁰F) loaded with the primer that was specifically designed for hot and reactive ground conditions consisting of detonating cord and packages emulsion that specifically formulated to inhibit exothermic reaction then tied in with a combination of non-electric surface delay detonator and detonating cord initiator (short length non-electric surface delay detonator housed in plastic connector).

Feb 6, 2023

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By Kim Henley, Chris Batten

This paper discusses the use of the Orica WildFireTM flyrock model to help mining operations in Australia and Asia minimise blast exclusion zones for equipment, increasing utilisation and productivity and delivering downstream value

Feb 1, 2020

By D. Preece

The mining and oil industry employs techniques such as geologic mapping, core drilling and electromagnetic and potential field techniques to explore for new deposits. Since new discoveries of major near-surface ore bodies are becoming progressively rare and since traditional exploration methods are unable to resolve ore bodies deeper than about 500m, high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3km.

Jan 1, 2011

By A. S. Tawadrous

Fines are produced in any blasting application. Depending on the application, fines may or may not be a desirable product of the blast. In most quarry and construction applications, fines are considered an undesirable product since it does not constitute a sellable product and there are costs to the operation for disposal. On the other hand, in most open pits fines do not represent as much of a problem since the ore has to be crushed and ground after being blasted. Therefore, fines in such operations may reduce the energy consumed in the downstream operations.

Jan 1, 2012