Search Documents

By N Vijay Mohan, K V. Balamukund, G Ananth Ramulu

Jointing of steel rods in reinforced concrete structures needs careful consideration as it renders the structure weak at the joint. The jointing is usually done at sections of structural members, where the bending moment and shear force are least. Jointing is done either by overlapping the rods or welding or by mechanical splicing. A novel method of jointing them is by inserting the two rods in a steel sleeve and cladding it on to the rods by subjecting the sleeve to explosive energy. A rod jointed in this fashion is tested for direct tension and bending when used in a reinforced concrete beam. The test results show that it is an effective method. The advantage is that a number of joints can be made in a single operation.

Jan 1, 1993

By S Burchell

During the past few years, high-speed cameras, laser surveying equipment and photogrammetry have become standard tools for recording blast geometry and results. While laser profiling yields accurate 3-D measurements, most cameras capture only two-dimensional images. Attempts to extract 3-D information from photographs have been unsatisfactory. Recent advances in electronic imaging and computer programming have made it possible to develop a 3-D computer based analysis system which can capture and measure 3-D images quickly and accurately. This paper describes the technology to create 3-D images and to analyze blast geometry before, during and after the blast.

Jan 1, 1992

By D T. Froedge

To preface these remarks, it is not intended that this paper be a criticism of anyone or any organization involved in drafting the current regulations, for it appears that everyone involved in the process has made an extreme effort to be safe. We wish to show that in this case by making huge safety margins, we have created an unsafe condition in another area. That is by creating vast safety margins in the area of mobile transmitter intensity versus distance scales we have caused a severe handicap in the use of the mobile transmitter in securing blasting areas. The use of these mobile transmitters, which are absolutely essential in clearing areas where there are woods, mountains, or urban structures is virtually eliminated because of the safety factors prescribed in the regulations. We wish to show that these mobile transmitter safety factors are much too great, and can be traded off to increase the margin of safety in the ability to clear blasting areas.

Jan 1, 1975

By Winston Wilches B., Scott Scovira

This paper discusses recent changes to the emulsion blend blasting agent used at the Drummond Pribbenow Mine in Colombia, one of the world’s largest open pit coal mines, and the resulting improvements in rock breakage and excavator productivity. Based on field evaluations, the use of High Density Ammonium Nitrate (HDAN) can be effectively implemented in an emulsion blend blasting agent, yielding excellent results in terms of energy release, shelf life and velocity of detonation (VOD). Field evaluations showed that formulations using HDAN exceed the performance of the actual 50%/50% emulsion/ANFO blend using Porous Prill Ammonium Nitrate (PPAN). PPAN is conventionally used for emulsion blend manufacturing, with physical characteristics to facilitate sensitivity during the detonation process.

Jan 1, 2014

By Peter Bellairs, Anthony Bubb

The Porgera Gold Mine is located at an altitude of 3000m in the central highlands of Papua New Guinea some 600 km Northwest of Port Moresby the capital city. Access to the mine is via a five hour trip on an unsealed road from Mount Hagen the nearest regional centre or 40 minutes via air. The mine operates on a fly in - fly out basis and currently produces ore from both opencut and underground operations with the former providing the bulk of the mill feed. Opencut mining utilises conventional truck / shovel, drill and blast methods on both 10 metre and 14 metre bench heights with the larger benches being restricted to the stripping areas. This paper presents the strategy used and the results of a blast optimisation process in the opencut that was a joint effort between the mine personnel and the explosives manufacturer/supplier.

Jan 1, 1997

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By Thomas J. Snyder

Modern quarry management should be alert to every opportunity to improve productivity and reduce operating costs. In this paper, the author outlines areas in which explosives suppliers should be encouraged to propose changes. He also supplies guidelines for evaluating these proposals, suggests yardsticks for measurement, and stresses the need to be open-minded when dealing with imaginative, innovative concepts.

Jan 1, 1988

By B Mohanty, R Yang

Blasting vibration information is now commonly used to diagnose blast malfunctions. These range from limiting vibration levels to protect normal dwellings to determining scatter in detonator firing times, and even to rating of explosives in the borehole. Although blasting vibrations have the potential to yield reliable information in all these issues, there are key restrictions on their specific use, which are often ignored. These include all aspects of instrumentation, and sensor layout, as well as methods of analysis. This paper highlights these limitations. It emphasizes the distinction between near-field and far-field seismic recording in terms of borehole dimensions and blast geometry. Several case studies from both underground and open-pit blasting operations are discussed to illustrate and emphasize the essential characteristics of blasting vibrations and their optimal use in diagnosing blast malfunctions.

Jan 1, 1997

By S C. Brashear, D A. Anderson, A P. Ritter, S R. Winzer, R Broughton

Results of quarry blasts can be quantified to show the effects of controlled variables. Two studies have been carried out: one to document the effect of delay on fragmentation and the other to show the effects of higher relief patterns and more accurate initiators. By using such techniques as highspeed photography and timing studies of mucking and crushing operations, subtle differences in blasting efficiency can be measured and quarry blasting can be optimized. Given the range of available and developing blasting technologies, quarry operators should resort to quantitative analyses of their blasting practices to get maximum productivity.

Jan 1, 1985

By David A. Paul

Over the past several years a great deal of information on blasting vibrations and their effects on structures has been generated. Much of this knowledge has been gained through the use of ground vibration measuring equipment. While this type of information is valuable and gives us great insight into damage that can be incurred by structures from this source, very little, if any, information of this quality is available for the vast majority of cases in which an engineer is called upon to investigate alleged damage from ground vibrations. For the investigative engineer, then, the problem becomes one of accumulating whatever data is available and drawing a conclusion as to whether or not the subject structure was in fact damaged by the blasting vibrations. Such an analysis certainly requires a working knowledge of the literature on the subject and as much experience as he can bring to bear. Even thus armed, however, the data is often ambiguous, confusing, and/or contradictory. A practical approach is presented herein to aid the engineering investigator in arriving at the best possible conclusion available with the information at hand.

Jan 1, 1983

By Ingvar Hansson, Bjorn A. Jonsson, Bernt Larsson

In the Kiruna Research Mine, Sweden, four large open stopes have been mined, leaving intermediate piIlars and crown pillars. At the final stage of mining mass blasting of the crown pillars above two of the stopes was carried out. The crown pillars contained some 290,000 tons of iron ore. In the mass blast a new initiation technique was used, utilizing the new non-electric system NONEL ? UNIDET. The blasting technique including vibration control is described. The mass blast resulted in high recovery, good fragmentation and low vibration levels.

Jan 1, 1986

By Farshad Rashidi Nejad, Ali Asgari, Sanaz Norouzi

Blasting is known as the first step of rock breakage in mines. An indication of the importance of blasting is that more than 1 billion kg (2.2 billion lb) of explosives are used annually in Australia and 3 billion kg (6.6 billion lb) in the United States for rock breakage, more than 85% of which is used in the mining industry. The notion that blasting, as the first step of comminution, plays a significant role in crushing and grinding energy consumption is not an unfounded thinking. It can be noted that the comminution electrical energy consumption decreases in these ways: First, if the feed size to the primary crusher is decreased, less energy will be required to crush the ore to the same product size. Second, a decrease in work index (Wi) related to additional macro fracturing and micro fracturing within individual fragments.

Jan 1, 2015

By David Siskind, Mark Stagg

Vibrations from Dade County (Miami area) quarry blasting and structure responses were measured at 11 locations between February and April, 2000, and 10 homes were inspected to analyze the characteristics of their cracking and other damages. These results were combined with information collected by the County and other studies done in south Florida for a blasting impact assessment specific to this area. In addition over 40 quarry blasts in the nine-week monitoring period, about 800 measurements were available from previous monitoring in Dade and neighboring Broward counties. An overall worst-case analyses based on the highest individual amplitudes suggested that vibrations in some areas could have been as high as 0.35 in/s. While amplitudes in the study period were below this value, they were found to be relatively high for the distances and charge sizes. Attenuation with distance is less in Dade County than found elsewhere with quarries having to use scaled distances several times higher than similar sites in the north. Consequently, the vibrations are perceptible at very large distances.

Jan 1, 2001

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985

By Catherine T. Aimone

A series of experiments have been performed to characterize fragmentation and microcracking in quartz monzonite copper porphyry. The flyer plate impact method was used to generate plane shock waves in rock specimens for impact pressures between 1.6 and 7.3 GPa and impact pulse durations between 1.1 and 7.0 µs. The effects of pressures up to 4.8 GPa and pulse duration on fragment size distributions and microcrack densities were studied. The results show that pressures effect particle sizes to a greater extent at higher pulse durations. However, changes in pressure and pulse duration show little influence on the density of microcracks induced during explosive loading. These results indicate that the nucleation and growth of microcracks in rock subjected to shock waves occur uniformly throughout. A substantial decrease in particle sizes for high pulse durations is attributed to more time allowed for microcracks to grow and coalesce, forming individual particles.

Jan 1, 1985

By Daniel Haines, Benjamin Konshak, Michelle Crull

American Technologies Incorporated Group (ATI) is the prime contractor with U.S. Army Corps of Engineers, Huntsville Center (CEHNC) in the Honolulu District for the removal of munitions and explosives of concern (MEC) at the Former Waikoloa Maneuver Area. The site is approximately 123,000 acres on the Big Island of Hawaii, which was used as an artillery firing range with live ammunition and other explosives deployed. ATI utilizes state of the art metal detection equipment to find and excavate metallic anomalies that have hazard potential. Both the investigation and disposal procedures present challenges due to residential communities and archeological sites that are located in and around the site. In order to excavate metallic anomalies safely and without adverse impact, ATI utilizes CEHNC-designed, open front barricades constructed of sandwiched sheets of aluminum with a support structure. When munitions or explosives are located, ATI is responsible for safe disposal using shape charge perforators to detonate the item where found. Sandbags are used for mitigating the effects of all detonations.

Jan 1, 2008

By Paul Worsey, Randall Franklin

This paper is based on an undergraduate research project undertaken for the explosives emphasis in the UMR mining engineering degree program by the first author. The purpose of the selected research topic was to investigate the impact sensitivity of commercial detonators to determine their relative safety for handling and how much abuse they can take without accidentally firing. A modified BAM tester was used for the investigation. Both electric and non electric detonators were impacted at incremental positions along their length to determine the relative effect of their various components. Repeat impact tests were also conducted to see how a damaged cap would react to repeated abuse. The results indicate that it takes a significant amount of impact energy to initiate commercial detonators. They also indicate that repeated abuse can increase sensitivity. Modern commercial detonators appear to be relatively insensitive to impact (an order of magnitude above RDX in the standard BAM test) and this is mainly due to their construction. This explains why damaged caps with exposed powder are more sensitive. Their measured insensitivity correlates with rough handling not being a major cause of blasting accidents.

Jan 1, 2004

By Thomas E. Ricketts

Limited void volume blasting (LVVB) occurs when rock is blasted into a volume that is not sufficient to let the rock expand to its free-bulking value. The freebulking value is obtained when the rock particles have enough space to separate, tumble and rotate to produce the maximum amount of void possible between the fragments when they finally come to rest. Although bulking value depends on particle size distribution and shape, a typical free-bulking value for uniform, finely broken shale is about 1.67. LVVB occurs in almost every type of blasting used in both surface and underground mining operations. For example, in multiple-row bench blasting for surface mining, the final delays that are designed to fragment the rock furthest from the free-face are generally confined by previously blasted rock which results in a LVVB situation. In underground mining, the blasting is automatically confined and is commonly done intentionally to limited void volume to reduce mining cost and improve safety. LVVB primarily affects rubble bulking and thus the excavation of the broken rock which is related to the productivity and economics of a mining operation.

Jan 1, 1989

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Savas Gorgun

The principal disturbances created by blasting in open pit mines are vibrations, air blast and fly rock. All of them, under some circumstances, caused damage to structures nearby and apart from this can be the source of permanent conflict with the inhabitations who live close to the operation. Therefore, prediction of ground vibration components is of great importance for the minimisation of the environmental complaints. This paper presents the result of ground vibration measurements induced by bench blasting realised at Can Open Pit Coal Mine located close to the residential area of Can town. Within the scope of this study, in order to predict peak particle velocity and determine the slope of the attenuation curve for this site, ground vibration components were measured for blast events during bench blast optimisation studies over a long period. During the study, while the parameters of scaled distance were recorded carefully, the ground vibration components were measured by means of two different types vibration monitors (White Mini-Seis and Instantel Minimate Plus Model) for 54 blast events. At the end of evaluation an empirical relationship with reasonable correlation was established between peak particle velocity and scaled distance for this site.

Jan 1, 2001

By Otto E. Jr Crenwelge, Timothy A. Peterson

We have developed a site-specific method for analysis, prediction, and control of ground vibrations induced by overburden blasting operations in surface coal mines. Field tests conducted at R&F Coal Company have verified our approach for obtaining signatures of the overburden vibration characteristics at locations of interest near the mine, selecting the optimum excitation frequency for minimizing vibrations, measuring and synthesizing multiple-charge excitation signals for minimizing vibration amplitude and duration and controlling frequency, accurately predicting the multiple-charge vibration response in both the time and frequency domains, and accurately controlling the blast detonation to achieve the predicted vibration control. Initial field studies also indicate that by minimizing the vibrational energy radiated from the blast zone, and by optimizing the number of charges detonated per delay period as allowed by this technique, more effective use of the explosive energy is obtained within the blast zone itself for improving overburden fragmentation, swell, and cast. In all of the phases of this technique, including actual blast detonation, personal computer hardware and software have been verified for use in either field or office environments.

Jan 1, 1986