Search Documents

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

Explosive manufacture, handling and transportation is hazardous and special precautions should be taken while manufacture, handling and transportation. Various regulations and rules defined in explosive act and factories act of India are discussed in this communication. General process control measures during the manufacturing of different types of explosives are also dealt in detail. Various processes hazardous in manufacture of various explosives like slurry explosives, PETN, detonators, styphnic acid, lead azide and lead styphnate and special precautions to be taken during the manufacture of the above explosives are also discussed.

Jan 1, 2007

By DuPont Magazine

RBH Note: as stated many times in these articles, frozen dynamite was one of the greatest hazards facing the blaster. It wasn’t until the late 1920s that it was solved for good, with the introduction of nitrated ethylene glycol as a partial replacement for nitroglycerin in dynamites. The du Pont low freezing dynamites contained TNT, DNT, or nitro-substitution compounds of various sorts.

Jan 1, 2015

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Randall Head

The drilling at the Taum Sauk Reservoir was a unique compilation of the latest technology and everyday common sense. This site is comprised of rhyolite, which is 30 times harder than limestone in comparison. Using some of the most state of the art drills, coupled with GPS guidance, angular drilling systems, and an ordinary piece of string, some of the most amazing drilling feats were accomplished. By constructing the new dam on top of a mountain that had been blasted once before nearly 50 years ago treacherous conditions for the drills and crew were a challenge. The drills had to be flown in by cranes to get to their locations, where they then drilled anywhere from 2.5 to 6 inch (6.4 to 15.2 cm) holes at angles up to 24.4 degrees. Custom drill bits were designed by the drilling crew to tackle feats such as drilling holes up to 120 feet (36.6 m) deep. A main challenge was the shape of the reservoir, as it is not in a straight line, but rather round, so no technological way was readily available to use to drill. Common sense came in and an ordinary piece of string was used to aide in drilling the hole. A revolutionary step was that our drill was used to core our own samples. By using our own equipment, we were able to complete this task for one-third of the cost of having a third party contractor obtain the core samples. On this unmatched jobsite, it has been established that technology has come a long way, but when all else fails, a piece of string will do just fine.

Jan 1, 2010

By Agung Wibowo

The incident of Ammonium Nitrate explosion in Beirut on August 4, 2020, became a wake-up call to Ammonium Nitrate stakeholders for mining and construction regarding the deadly risks associated with explosives management. This is a very expensive a lesson learned for all parties involved in the storage of explosives.

Feb 1, 2020

By Hector O. Romero, Paulo C. Fernández A, Christian Rees Prado, Claudio C. Gajardo

In open-pit mining, estimating post blasting displacement and spillage accurately is essential to guarantee operational efficiency, ensure alignment with production plans and their associated key performance indicators. The absence of predictive modeling tools on blasting operations results in several critical challenges, including operational reworks due to deviations in material displacement, significant discrepancies between mine and plant (ore grade dilution included), misalignment with the reported production plan, and increased operational costs due to inefficient use of resources. This study, conducted at Los Bronces Mine operated by Angloamerican, Chile, addresses the application of a three-dimensional simulation tool that, through numerical modeling, is capable of predicting post blast rock displacement. The implementation was carried out in a pit phase characterized by blasts near the pit boundaries, with a high risk of material spillage and potential blockage of the only access ramp to the extraction levels. By the integration of key design parameters, such as blast pattern geometry, detonating time, explosive charge distribution and pre and post blast survey, an optimal calibration was achieved and validated in seven blasting events to date, reaching an accuracy greater than 80% in estimating post-blast rock displacement and spillage volumes. Furthermore, this study allowed the evaluation of different pattern alternatives with and without spillage mitigation measures (use of air decks near the free face), obtaining a high correlation and accuracy exceeding 95% in predicting the selected design outcome, supporting optimal design selections. The result highlights the usefulness of the model as a decision-support tool for blasting engineers and short-term planning, by reducing the need for unnecessary operational reworks, improving geological and operational reconciliation, and ensuring the alignment of the extracting plan with production targets. The current average deviation is 15%, with higher deviations observed in blasts with smaller volumes of spill or where the simulated sequence was changed before blasting. The use of this type of three-dimensional numerical modeling represents a significant advancement for blast engineering and the optimization of key performance indicators in open-pit mining operations.

Jan 26, 2026

By Wm. Reisz

There is no universal standard for Standard Operating Procedures (SOP’s). Every blasting operation has its own unique circumstances, its own methodologies and its own unique demands. It would be nearly impossible to create a one-size-fits-all document that would be totally appropriate for every blasting scenario. But there are universal objectives that should be adopted in any set of blasting SOP’s.

Jan 1, 2010

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Robert Hopler

On June 13, 1912, the final decree of dissolution of the DuPont explosives trust was handed down, and the resulting new companies began operating at the beginning of the new year. The property assets granted to (or retained by) the companies were as follows:

Jan 1, 2014

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By N Gkikizas-Lampropoulis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper interprets previous experimental information on the effect of delay on fragmentation with the aid of some new experimental observations of the time of detachment of the free face of the blast as well as results of numerical modelling. It was shown that detachment of the burden occurs at delays shorter than the one which produced optimum fragmentation in the experiments, suggesting some fragmentation improvement due to gas action. In addition, at the spacing to burden ratio of the experiments, the damage zone from an earlier detonating charge extends the distance to the neighboring charge, essentially affecting the burden of some of the holes of the blast, at detonation time. Computer modelling demonstrated that increased spacing results is less overlap of stress induced damage zones meaning that there is less influence of delay on stress wave induced fragmentation. It was also shown that simultaneous initiation results in less back break, while increased back break may result even with short delay times.

Jan 1, 2016

By Mick Fritz, Gregory Poole

Construction blasting is always challenging when in close proximity to existing structures, but when you are next to a landmark like Sanford Stadium at the University of Georgia it can get intense. Blasting on this project was performed less than 100 feet from students studying in their dorms at Reed Hall. Some shots are only a few feet from the columns on the stadium that hold up the sky boxes where meetings were being held while blasting was being performed. If a shot goes vertical the rocks would go through the floor of the sky boxes.

Jan 1, 2011

By NA NA

Copyright © 2020 International Society of Explosives Engineers

Feb 1, 2020

By Anderson Meireles, Vladimir Carrasco, Carlos Feliciano

Adopting new technology in drill and blast requires a structured implementation process, as it represents a significant change in a traditionally conservative industry. It involves addressing initially unknown implications. As the problem is not yet acutely felt, developing a market strategy must be approached from the customer’s perspective, considering how the product can optimize their activities or enhance flexibility. To achieve this, it is essential to have a comprehensive understanding of the context of the customers identified in the deployment process pipeline. This paper discusses aspects of introducing wireless initiation technology - the initiation of primers through a magnetic field without physical connections - in Brazil. Additionally, it presents a case study of the application of a structured process of sales with purpose in an underground mine. By identifying key opportunities that were highly profitable for the client, the necessary awareness was created, leading them to recognize the technology as an enabler for exploring their mineral deposits in a new way which allowed a successful change management process. Based on the applicable technique, a preloading project was developed to maintain inaccessible areas with high-grade precharged with the area loaded with wireless primers acting as a temporary pillar and controlling dilution throughout the orebody. Once the excavation of the stope was completed, the pillar was successfully blasted and the material - once considered lost in the original plan as a rib pillar - was recovered after serving its structural function. Through this method, the metallic recovery of the stope increased without dilution losses. Demonstrating economic viability and stablishing the previously unknown technology as a strategic tool for optimizing stope recovery.

Jan 21, 2025

By William Reisz

The explosives and blasting industry has a commendable safety and security record, especially over the last several decades. This is due in large part to our newer technologies, better training and education, engineering practices, corporate initiatives, our professional organizations, and whether we like to admit it or not - our regulatory agencies.

Jan 1, 2012

By Dr. Calvin J. Konya, Anthony Konya

Blast violence has always been a criteria that has been analyzed without a quantitative approach relying on opinions of those viewing the blast and oftentimes does not transfer between open-pit mines, quarries, and construction projects. Added to this confusion is that on many regulate projects, such as U.S. Army Corp of Engineers construction projects, the definition of "flyrock" or violence can vary, and contractors must be able to meet this requirement. This project analyzed hundreds of blasts from various construction projects to develop a new metric to determine blast violence - the Violence Factor. If a blast is fired using 1.25" (32 mm) diameter product and a 10-foot (3 m) bench, vertical uplift of 60 feet (18.3 m) would be considered extreme and violent by any professional in the industry. However, a 100-foot-high (30.5 m) bench using 12" (305 mm) bulk product, having a vertical displacement of 60 feet(18.3 m)might be considered typical or non-worrisome. This is where violence factor is beneficial as itprovides a system of scaling the violence of a blast based on the bench height to give manager a keyperformance indicator (KPI) which is easy to monitor and can provide a large amount of information onsite-specific design variables for their performance on blasting and the end-results of the blast. The Violence Factor of a blast is an integer which is scaled to determine how high vertical uplift of a blast is compared to the bench height. This project analyzed numerous blasts to determine what blast design variables contribute to violence. This violence has also been shown to occur when a non-optimal breakage mechanism, cratering, occurs and the design criteria that lead to this cratering. Finally, this paper will present typical results of various levels of violence including backbreak, fragmentation, and muckpile configuration.

By Dr. Calvin J. Konya, Anthony Konya

Blast violence has always been a criteria that has been analyzed without a quantitative approach relying on opinions of those viewing the blast and oftentimes does not transfer between open-pit mines, quarries, and construction projects. Added to this confusion is that on many regulate projects, such as U.S. Army Corp of Engineers construction projects, the definition of "flyrock" or violence can vary, and contractors must be able to meet this requirement. This project analyzed hundreds of blasts from various construction projects to develop a new metric to determine blast violence - the Violence Factor.

Feb 1, 2020

By E Novikov, D Johansson, U Nyberg, A Beyglou, N Petropoulos

Fragmentation is an important factor for improving downstream processes in mine operations. Six trials have been conducted at the Aitik copper mine to investigate the effect of ultra-short inter-hole delay times, i.e. smaller than 1 ms/m of burden, on fragmentation. Swelling, MWD data, and crusher efficiency were also evaluated for trials. According to the results, the effect of examined short inter-hole delay times, i.e. 0.14 to 0.86 ms/m of burden, on fragmentation was found to be marginal. Delay time of 0.43 ms/m of burden resulted in slightly finer fragmentation and larger swell; however, the effect of short delays was overshadowed by the effect of small variations in specific charge.

Jan 1, 2014

By Chris Vagasky

On July 10, 1926, lightning struck at Picatinny Arsenal, New Jersey, and caused the explosion of at least 600,000 pounds (272,000 kilograms) of ammunition, resulting in more than $600 million (2015 dollars) in damage, the destruction of 200 buildings, and 22 deaths. Fortunately, there has not been a major incident involving lightning and explosives in the US in some time, though lightning has destroyed fuel storage tanks in recent years, including in North Dakota, Texas, and Ohio. Lightning poses a significant hazard to the explosives industry. Carrying high currents and temperature, lightning can cause explosives to detonate, start fires near storage facilities, and injure or kill operators.

Jan 1, 2017