Search Documents

By G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method. The rockmass is traversed by three to four joint sets and few minor shear seams. Rock Class “Q” values were between III and IV. Tunnel was excavated by full face parallel hole drilling blasting method. The adopted blasting method consisted of drilling 45mm (1.77 inch) diameter holes to a depth of 2m and the drilled holes were charged with 40mm (1.57 inch) diameter cartridge explosives and charges were initiated with half second non electric initiators. The perimeter holes were drilled at closer spacing of 30cm (1 feet) and alternate holes were charged using 32mm (1.23 inch) diameter cartridges explosive. Low dipping foliation joints present in the rockmass tend to slab in crown portion and erratic occurrence of intrusive bodies lead to unpredictable behavior of rock mass posing a major challenge for the safe excavation. Stability was a major issue through controlled blasting under constant supervision too could not limit the overbreak in certain weak rockmass conditions thereby exposing cavities of about 2.5m (8.2 feet). The stabilization of these cavities and handling the overbreak due to rockmass condition was time consuming and warranted additional supports. With systematic measurements and controlled blast designs the Horse Shoe Shaped Tail Race Tunnel of 9.1 m (29.85 feet) diameter and 304m (997.37 feet) length to connect with Downstream Surge Gallery of 314m (1030 feet) length, 18m (59 feet) wide and 58.8m (193 feet) height in thinly foliated and jointed biotite gneiss rockmass was successfully excavated.

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019

By Paulo Couciero

Since explosives are the source of all energy used for rock blast fragmentation and heave, multidimensional effects in the detonation driving zone become essential to better describe the detonation process. In order to use the explosive as an energy source-information for more realist blasting performance simulations, a simple and effective modelling strategy is desirable. Facing this challenge, an engineering approach to two-dimensional unconfined non-ideal detonation is proposed. Based on the elliptical construction of the shock locus, the model combines the axial cylindrical stick Q1D solution with some additional limiting conditions to determine the sonic edge of the charge. For a given set of rate law parameters and velocity of detonation, a complete axial solution is firstly computed through the Q1D model. From this solution, a vital relationship between the axial shock curvature with the shock shape parameters can be stablished. Once this relationship is found, the problem simply reduces in finding the shock shape parameters subject to the sonic edge condition. As a result of this calculation, the corresponding charge diameter can be found. Consequently, the proposed model can map the diametereffect curve by relating the unconfined velocity of detonation with its corresponding diameter. Finally, because of its low computation cost, the proposed engineering approach can be also used for characterizing the rate law parameters by fitting to data from unconfined detonation experiments

Jan 1, 2019

By J Silva Castro, W C. Wedding, B T. Lusk, J Calnan, E G. Morris

The emergence of electronic detonators for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. This paper reports on an independent study quantifying the accuracy of two electronic and two non-electric systems in which 674 detonators were tested. This research aimed to determine the accuracy of commercially available electronic detonators as compared to non-electric shocktube systems. Each system was tested over the viable ranges of delays available. Statistical models were then applied to quantify the scatter present in each system. Suggestions for the use of electronic detonators are made from the findings of this work. This work was made possible through funding from the United States Department of the Interior Office of Surface Mining Reclamation and Enforcement.

Jan 1, 2012

By Jerry Newton

The bulk explosives industry is relatively young compared to how long explosives have been in use. It's been around for about forty years, about the length of a person's career. This period of explosives history has seen constant change. The type of product, the manufacture and the trucks that haul it have changed a great deal over the years.

Jan 1, 1997

By Alastair Torrance, Italo Onederra, Do Sun Kim, Kush Patel, Gary Cavanough

Reactivity of ammonium nitrate-based explosives is associated with the presence of sulphide in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. This paper explains the mechanism of these reactions, the potential cause of spontaneous detonation and how inhibited explosives prevent the reaction

Jan 1, 2019

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By John W. Brown

The purpose of this paper is to describe different methods of evaluating the performance of your current rotary blast hole drills. To properly evaluate a drill rig's performance you should include a competent driller, mechanic, rotary bit technician and a technician representing the manufacturer of the drill.

Jan 1, 1998

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In this paper, differences between the industry-standard Holmberg-Persson (H-P) approach and a semi-analytical vibration prediction model called full-field solution (FFS) are analized. The analysis is conducted at two levels: vibrations and rock damage.

Feb 1, 2020

By Orica Peru, Pedro Lozada

Proper management of exclusion zones in blasting operations is essential to ensure safety without compromising operational efficiency. In Peru, mining regulations establish minimum exclusion distances specifically for personnel (500-meter radius / 1,640 feet), but do not define clear technical criteria for equipment. As a result, conservative distances such as 200 meters (656 feet) are often applied, negatively impacting productivity. This study proposes a technical-scientific methodology to reduce equipment exclusion zones, based on the use of advanced technologies such as drones, high-resolution cameras, and specialized software tools. The solutions used allow video recordings of blasts to be transformed into dynamic data through artificial intelligence and computer vision, as well as execute probabilistic simulations of the flyrock phenomenon using Monte Carlo algorithms and physical models calibrated to real operating conditions. Technological integration enabled the simulation of real operational scenarios, considering variations in critical blasting parameters that directly affect flyrock generation, such as drill diameter, explosive density, linear charge, and stemming height. Additionally, the Terrock methodology was incorporated, allowing the behavior of the rock mass to be included as a variable in risk assessment, improving analysis accuracy under different rock hardness conditions. The methodology was applied in four phases: diagnosis of the current design (15 blasts), modeling, validation of the calibrated model (6 blasts), and subsequent operational implementation. As a result, it was determined that the exclusion radius can be safely reduced from 656 to 492 feet (200 to 150 meters), maintaining as the main restriction the use of stemming lengths greater than 5.0 m. This optimization has the potential to generate tangible benefits, with estimated monthly savings exceeding USD 50,000, associated with reduced evacuation times, lower fuel consumption, less equipment wear, and increased productivity in drilling and hauling activities. The comprehensive approach presented here highlights the transformative potential of digital technologies applied to blast management, contributing to safer and more efficient mining operations.

Jan 26, 2026

By Michael Milstein

Northwest Research Station said as more and more older dams are removed to benefit fish, it’s become clearer that rivers rework themselves quickly.“Where the dam is relatively small, it’s a quick response,” he said. “The river quickly forgets.”

Jan 1, 2010

By Michael S. Wieland

"This report investigates whether it is tractable and thereupon reasonable to remove the boosterinfluences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations."

Jan 1, 1999

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Clay McNail, Paul N. Worsey, John Schillie

"This paper is the result of undergraduate student research over the period of 2 semesters at UMR, which was focussed on developing a practical way to pneumatically stem horizontal boreholes, mostcommonly used underground. The majority of dry horizontal underground boreholes are pneumatically loaded with bulk ANFO. ANFO is preferred due to its low cost and the ease of pneumatic loading. However, stemming underground in the United States is a rare practice. In sharp contrast, stemming material (crushed stone or drill cuttings) is virtually always used in surface holes. The purpose of stemming is to increase blast efficiency by containing the explosive energy in the ground and to reduce environmental effects such as air-blast. The problem with stemming horizontal boreholes are; gravity cannot be used to load stemming material and the ANFO does not have a good interface due to problems with withdrawing the hose and the loading itself. This work follows on from Wilkins’ work on stemming angled boreholes."

Jan 1, 1999

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur.

Feb 1, 2020

By Rolf R. Schillinger

Subject of the paper are blasting vibrations as sources of environmental molestations including acceptance level,complaint level and damage level as well. Besides, the subject shows a comparison of international regulations and their problematical aspects. In consideration of blast induced immissions the subject shows that human annoyance has become an important place in blasting works. It provides a solution proposal how to minimize environmental effects of blasting works.

Jan 1, 1996

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur. Two recent render-safe operations conducted in and around urban environments dealt with deteriorated, sensitive dynamite and damaged blasting caps. Utilizing innovative neutralization chemicals and processes to render-safe the deteriorated dynamite, while protecting the general public, proved to be the safest, most environmentally responsible and cost-effective way to approach the problem. In both cases, the explosives, old dynamite and detonators were found in abandoned, unlocked magazines. The dynamite was in a significantly deteriorated state, which was evident due to the nitroglycerine found leaking in,around and under the dynamite cartridges. Iron wire permissible electric blasting caps were also found in a corroded condition with exposed explosives and un-shunted lead wires. With occupied buildings within 180 feet (54.86 meters) of the magazines, any procedure (e.g. transporting, countercharging, burning) that could potentially cause a detonation was not an option. In the event of an unplanned detonation during neutralization operations, several blast mitigation methods were employed to safeguard the site. This operation and a similar one with over 1,000 pounds of crushed and buried leaky dynamite were unique since all the explosives were rendered-safe and neutralized on site. The use of advanced neutralization products and filtering processes allowed for a safer, more environmentally responsible way to resolve the problem. The magazines and all residual solids and fluids were tested and confirmed by independent labs to have no explosives residues. The effluents were treated on site, tested and met safe levels, so they were disposed of at a local municipal wastewater facility.

By Tony Rorke, Tamara Wiseman

Due to the advancements in technology it becomes easier to obtain accurate measurements for mining, quarry, and construction operations even in the most remote places. The use of off-the-shelf photogrammetric imaging technology and unmanned aerial vehicles (UAVs) are becoming more common in the mining industry for blast design and surveying. Pattern optimization, face profiles, pre and post blast volumetric, stockpile measurements and mine mapping are all areas where these technologies can be used with ease.

Jan 1, 2015

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is commonly adopted method in underground hard rock mining. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason being the unavailability of free faces as compared to open cast bench blasting. The geological and geotechnical parameters changes gradually even within the stope itself. So the blast design parameters should be planned according to the scenario of upcoming ring. Blast design parameters like burden, toe spacing, inclination of blast holes, diameter of blast holes, charge density of explosive etc plays an immense role in rock damage. For the proper breakage of rock, the movement of burden is prime objective. To study this, explicit dynamic based modeller of M/s Ansys was used. The burden values were varied from 20-65 times diameter to assess optimum burden value during the study. The models were simulated for the rock having 35 MPa uniaxial compressive strength and 102 mm blast hole diameter. Altogether three holes were blasted having hole depth 14-14.5m. The blast design parameters and respective blast induced ground vibration has been measured at the experimental site. Core sample of the rock of experimental site has been used for the evaluation of geotechnical parameters. These geotechnical parameters were inserted into the simulation model. The volume of rock excavated along free face has been calculated in each model. It has been found that the burden value can varies from 35-40 times blast hole diameter (3.6-4.1m) to achieve greater volume of rock along the free face for 102 mm blast hole diameter and rock of 35 MPa uniaxial compressive strength.

Feb 6, 2023

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015