Search Documents

By CVB Cunningham

"The Kuz-Ram model as originally proposed included an error in assuming that the mean fragmentsize predicted by Kuznetsov’s equation was actually the 50% passing size. In 2003 Spathis began discussions on this issue and recommended correcting the equation. The correction produced more fines in the predicted fragmentation, which had been a criticism of some users of the original model. Ouchterlony subsequently showed that the error had, if anything been beneficial, and that the Swebrec function adequately covered the fines. This author shows that the Spathis correction does not assist the fines correction in examples examined, but tends to underestimate coarser fractions. An intrinsic problem of communication between academics and engineers is a root of misunderstanding on both sides, and requires patience by both parties to enable value to arise."

Jan 1, 2016

By Dale Preece, Mike Stern, Steve Piercey, Ayman Tawadrous, GC Zhao

The McArthur River uranium mine in Saskatchewan, Canada is the world’s largest high-grade uranium mine. It has employed a freeze-wall system consisting of multiple freeze pipes to control the large quantities of water encountered during mining.

Jan 1, 2011

By M R. Hettigner, J Nawrocki, C E. Johnson, P G. Cahill

This study evaluates the effects of both short inter-hole and intra-hole delay times on rock fragmentation and throw. Full-scale test blasts were analyzed at a granite quarry in Talbotton, GA. This analysis provides a representative understanding of timing effects on fragmentation in the field, different from previous lab scale studies that negate the effect of geology. Inter-hole delay times between 0 ms and 25 ms were tested on a series of 4 bench blasts and subsequently examined using photographic fragmentation analysis methods.

Jan 1, 2017

By Javier Castaneda, Luis Zozaya, Noel Huarachi, María Rocha

The objective of the project was to implement and calibrate drill and blast models supported by Geotechnical and Geological models as well as the mine and operation characteristics. The models would then be migrated to HxGN Blast to ensure a productive process that is simplified, digitized and optimized.

Feb 1, 2020

By Winfried Rosenstock

AEBT has been available for a couple of years and is successfully applied in Australia. Up to now it was mainly used in coal surface mining at the Australian East- Coast. Presently, the proved results reach ~ 50 % reduction of Drilling & Blasting costs and a productivity increase of between 10 and 20 %. In 2003 it was for the first time used in surface metal-mining. The mine features for the time being an extremely difficult geological environment and had above to be carried out in the transition level waste/ore. Reductions of wall control, powder factor and vibrations were the main target.

Jan 1, 2004

By A. Lindo, M. Held

The formation of NOx fumes is an undesired occurrence and is dependent on a variety of variables. Methods for detection of such fumes with blast analysis tools are available using color schemes for grading, but no quantification tools to measure concentration and cloud totals exist today. In cooperation with DIRS (Digital Imaging and Remote Sensing Laboratory) at RIT in Rochester, NY, Austin Powder has been looking for methods and techniques to identify and quantify total amounts of NOx by capturing cloud activity via a video feed from a drone in combination with measuring NOx and subsequent cloud modeling (i.e., plume segmentation). To accurately measure fume events, Austin Powder and the RIT team have been collaborating in performing small scale blasts at an Austin test facility and then transferring knowledge learned to full scale blasts at customer sites. The collected data will allow to identify any relationships between the total amount of explosives used and the quantity of NOx produced. The analysis of the total amounts of NOx and identification of blast areas those fumes originate from will help to better understand key factors that contribute to their occurrence as well as to quantify the severity of such events. By quantifying the magnitude and concentration of fumes generated by non-ideal detonations, the blasting technique can be optimized to minimize unwanted environmental effects and improve public perception of blasting as a necessary component of societal progress

Jan 1, 2024

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By Harley Cheema, Brandon Fryman, John Tatom

A new magazine propagation model has been proposed by the IMESAFR Science Panel for eventual implementation into the IMESAFR QRA program. Initial results from this QRA propagation model are now available.

Feb 1, 2020

By Timothy Smith, Matthew Ryan, Dr. Anthony Konya

Hybrid specifications are a relatively new style of specifications specifically for the drilling and blasting industry that has seen widespread use over the last decade with the U.S. Army Corp of Engineers. This paper analyzed how this methodology was applied to develop this specification for the Soo Lock Deepening Project.

Feb 1, 2020

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

By Joseph Indeck, Seokbin Lim, Andrew Thompson

In the design of explosively driven penetration devices, understanding the impact conditions between the explosively propelled penetrator and the target is one of the most important steps in optimizing the performance of the device. These impact conditions are especially prevalent when a shaped charge jet impacts concrete, which is not an ideal target material. The specific impact conditions, including but not limited to the impact angle and jet properties, create a great deal of variability that affects the performance and penetration of the shaped charge. The large amount of impurities and voids in concrete, along with its heterogeneous nature and the general strength characteristics, make concrete a non-ideal material for shaped charge jet penetration. These material characteristics lead to a highly non-linear deformation behavior of the concrete target during a hyper-velocity impact.

Jan 1, 2011

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By Jan Westberg, Roger Holmberg, Bernt Larsson

Over the last couple of decades there has been an increased demand from the market for precision detonators, partly because of a need for better blasting results and partly because of a need for better vibration control. Today's detonators have a pyrotechnical delay element which gives a relatively high time scatter, increasing with the length of the delay time.

Jan 1, 1988

By David Leidel, James Stuart

The 50 ohm resistorized electric detonator is commonly used in the oilfield for initiation of wireline conveyed perforating guns and other downhole explosive tools. This type of electric detonator provides some degree of safety above that of the conventional one ohm electric detonator, since a higher current level is required to initiate the device. In order to obtain the necessary data to develop safe distance tables from RF sources for the 50 ohm electric detonator, laboratory tests were conducted to determine the detonator’s “no-fire” current, AC impedance, and its susceptibility to ESD. The results were surprising as two types of failure modes were observed. The “no-fire’ current levels determined from Langlie “One-Shot” Test Methods were determined for the devices tested providing values for the 0.999 probability “no-fire” power level at a 95% confidence level. This data will serve as the basis for sets of safe distance tables from RF sources that will appear in the forthcoming edition of the Institute of Makers of Explosives Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators, (Blasting Caps)”.

Jan 1, 2010

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock. The first stage of the study was the recognition of the rock blast process in question, assessing key parameters that characterize this whole operation: geomechanical characteristics of the rock mass, implementation quality for drilling pattern and explosives charging (collar position, hole depth, explosive charge length and stemming size) and recognition of current blast designs. The central element of this study was the creation of a vibration attenuation and seed wave model which has allowed the characterization of this particular rock mass present in a region determined by the Minas-Rio team. The model is based on a near field vibration test, constituting a powerful tool in the design of blast parameters. The blast design developed from the damage model simulations basically modified the timing and sequencing. The aim of this study was to improve the fragmentation resulted by the blasting, considering the particle size requirements demanded by the primary crusher and to increase the productivity of the loading and hauling operations. The results were analyzed considering the effective productivity of the two different fleet types of shovels, where the authors have analyzed more than 46000 values of productivity from September 2017 to August 2018, taken from the Dispatch system. A significant increase in effective productivity of these load equipment was observed, 7% to the PC4000 fleet and 2% to the PC5500 fleet, values supported by statistical parameters and hypothesis tests.

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock.

Feb 1, 2020

By Tristan Worsey, John Rathbun, Andres Malone

A run of mine, low grade gold heap leaching operation is currently looking to increase ounce recovery by decreasing run of mine fragmentation size. Current blasting practices have resulted in an average fragmentation size of 80% passing 7.05 inches (179 mm). It is estimated that a decrease of 2 inches (51 mm) in the 80% passing fragmentation size has the potential to yield up to a 2.5% increase in the overall life of mine recovery within this ore body. This potential recovery increase could lead to an increase in recoverable ounces which, in turn, would lead to a better profit margin. As this particular deposit is composed of predominantly low grade heap leach the capital investment in a crushing facility was cost prohibitive, it was therefore decided to look into the current blasting practices as a means to improve fragmentation.

Jan 1, 2015

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012