Search Documents

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By George S. Rice, F. B. LANEY, A. J. Lanza, Edwin Higgins

Under its organic act the Federal Bureau of Mines is directed to conduct investigations relating to the improvement of health conditions in the mineral industries. This report describes the lead and zino deposits and the mining methods employed in the sheet-ground area of the Joplin district, Missouri, and discusses the causes and the methods of abating rock dust in the mines, the chemical and physical characteristics of the dust, and the quantities present in mine air. Although the preliminary investigation included a number of the "soft-ground" mines, the writer spent the larger part of his time in the sheet-ground mines, for in them alone was siliceous dust found in appreciable quantities. Some results of the preliminary investigation have been published by the Bureau of Mines in Technical Paper 105.a The territory covered in t~lCpreliminary investigation, during the period between November 7 and December 6, 1914, embraced parts of Jasper, Lawrence, Newton, and Greene Counties, Mo., and outlying districts in Kansas and Oklahoma. The remainder of the field work, to which 84 days during the period from February 9 to July 19, 1915, were devoted, was confined to the sheet-ground mines, the most important of which are situated in the vicinity of Joplin, Webb City, Carterville, and other smaller near-by towns in Jasper County, Mo.

Jan 1, 1917

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956

By Howard W. Wainwright

This bibliography was compiled by the Bureau of Mines as part of an investigation into the possible utilization of low-temperature coal-tar bases. The bibliography consists of literature and patent references from about 1945 to 1961 and is divided into the following headings: Analysis and Composition; Production, Synthesis, Reactions, and Utilization; and Separation, Purification, and Properties. Although over 1,000 references are included, no attempt was made to insure a comprehensive survey. The literature and patent references are arranged alphabetically by author or patentee. When several publications have the same author they are listed in reverse order of age, with the newest first. An author index is included because secondary authors are not cross-indexed. In almost every instance, the entry is accompanied by a Chemical Abstracts reference for those interested in locating an abstract of the original paper.

Jan 1, 1962

By T. M. Barczak, S. C. Tadolini

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of “topping off” the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

By E. C. Lane

[This is the tenth in a series of retorts on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee e end the Bureau of Mines of the United States Department of the Interior. The first report rave data on motor gasolines sold during .e winter of 1935-36.3/ The present report presents analytical data for 1,732 samples, representing the products of approximately 50 companies, which, as in previous surveys, include both lame and stall suppliers. In addition, the Pacific coast is represented by data that were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. he number of samples, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as follows: Regular price, 934 samples, 230 items, and 50 brands; premium price, 465 saris samples, 184 items, 40 brands; third-grade gasolines, 360 samples, 177 items, and of these terms as used in the surveys are follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.]

Jan 1, 1941

By E. C. Lane

["_&apos;_-is is t`-e tenth in a series of retorts on proferties of cornmerci-al motor fuels, m,-_de in accord^nce ::ith a cooper: tine aSreement between the Cooperative Fuel scorch (C.F.R.) Committo e ^nd the. PPure__u of Mines of the United_ States De_nartr.ent of the Interior. Zee first report rave data. on motor gs.solir_es sold. during .e winter of 19,-"1-3b. e are ent report presents an^..lytico1 data f&apos;i&apos;r samples, rerrerentin_E, t:-.e products of apyroximately 90 conr.anies, hich, as in previous surveys, include both lame and stall surnliers. In ?_"dition, the Pacific coast is represented by data that were avera,;el ty the Pacific Coast Technical Group before bein submitted and are rublisi,ed exectly zis they were received. As in previous s?nrve,rs, the data r~Lre divided into the three groups of samples of regular-price, premiu::--trice, and third-grade gasolires, and each group has been averaged sel c~r~.tely. he number of nmtles, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as folio:;s: Reg<.~-lar price, 934 ca.^rnles, 2c0 i to s, and ~0 brands; premium price, 460 saris les, lPitems, an&apos;. -C` brat&apos; i _~ t__ rd grade gaseline, 360 samples, 177 i te.^..s, and of these terms as _ised in the surveys are a:: follows:]

Jan 1, 1941

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By David D. Hottinger

Only a minimum amount of illumination is generally provided for many types of mobile surface mining equipment. This condition presents a hazard to operating personnel working on and around such equipment. To reduce this hazard MSHA has proposed safety regulations requiring minimum levels of illumination for hazardous zones on and in the immediate area surrounding surface mining equipment. This report describes a Bureau of Mines sponsored project demonstrating the feasibility and effectiveness of providing dragline illumination in compliance with the proposed MSHA regulations. A description of the computer aided design, on site installation and field evaluation of individual lighting systems for each of three different size draglines is presented

Jan 1, 1981

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d&apos;Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By Reinhardt Thiessen

"INTRODUCTION Coal is a complex substance consisting of many different constituents representing many chemical compounds, very few of which are known. It is homo genetic, however, in that it is derived almost entirely from plants. But plants as a whole are complex, being composed of a large number of tissues, each consisting of a large number of cells in a great number of arrangements and composed of a number of chemical compounds in great variety of proportions, and enclosing a large number of waste products representing a large number of' chemical compounds as cell contents. Coal should therefore be expected to be a very complex substance.That coals are formed from plants is no longer debated, but the manner in which coal was formed from the plants leaves many problems still unsolved. However, in general it is now conceded that all coals of all ranks and ages had their origin in deposits completely analogous to our peat deposits of today and that coal formation is a process that runs through the whole series, beginning with peat, and through, the various ranks of lignite, subbituminous, high-, medium-, and low-volatile bituminous, semianthracite, and anthracite in a related chain. In the study of coal, it is therefore of the utmost importance to study and to know not only the plants contributing but .also the manner in which they are transformed into the substances forming the deposits. It is therefore of the greatest value to review briefly the formation of :,eat as it is known today, and to inquire into the facts as to what plants contribute to peat, what parts and products prevail, what are the chemical compounds that enter and which prevail."

Jun 1, 1947

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company&apos;s safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By Michael G. Zabetakis

Vaporization of a solvent into an airstream at temperatures above the flash point of the solvent is hazardous if vapor is liberated at a rate that is sufficient to produce a flammable mixture. In may operations, the formation of such a mixture is prevented by rapid diluton of the vapors with air. The minimum air requirements for the dilution process are determined by the composition of the lower limit mixture at the temperature and pressure of interest. Because limits of flammability cannot always be calculated with sufficient accuracy for a proposed operation, they .rust often be determined experimentally. The present Bureau of Mines investigation was prompted by an application in which the lower limits of flammability of a number of solvent mixtures were required over a range of temperatures at atmospheric pressure. These limits were to be used along with available solvent-vaporization-rate data to establish minimum airflow rates needed to prevent the formation of flammable mixtures in an industrial process. Lower limits of flammability were determined for a number of mixtures containing methyl ethyl ketone, tetrahydrofuran, toluene, ethyl alcohol, and ethyl acetate in dry air-at atmospheric pressure and temperatures between 16° and 200° C. The experimental values were found to be in good agreement at with those predicted by Le Chatelier&apos;s law; variations with temperature were in fair agreement with those predicted by a modified Burgess-Wheeler law.

Jan 1, 1962

By W. H. Tomlinson

The fourteenth National First-Aid and Mine Rescue Contest we;; held at the State fairgrounds, Columbus, Ohio, October 2, 3, and 4, 1951. The meet, the first such event in 21 years, was under the auspices of the Bureau of Mines, United States Department of the Interior, and the Joseph A Holmes Safety Association and was sponsored by the National Coal Association, the United Mine Workers of America, and various State mine-inspection departments. The cooperating agencies that contributed to make the meet a success, in addition to the National Coal Association and the United Mine Workers of America, were the Kentucky Department of Mines and Minerals, Ohio Division of Mines, West Virginia Department of Mines, Pennsylvania Department of Mines, and the Columbus Convention Bureau. SUMMARY Fourteen teams from 6 States participated in the mine rescue contest, and 55 teams from 9 States competed in the first-aid contest. Only one of these teams entered as a combination team, that is, participating in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are listed in table 1.

Jan 1, 1953

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981