Search Documents

By Charles D. Wood

"Selected Topics,? in reviewing the control of emissions from diesel engine powered equipment used in underground mining, explores these fields of interest: hydrogen as fuel; lubricating oil as a source of particulates; applicability of stationary source scrubbers; worldwide diesel exhaust scrubbers; instrumentation technology for measurement of N02; control of emissions through application of sensors and microprocessors; use of fuel additives; technology transfer of marine diesel practice; technology required to use 4-stroke, aftercooled, turbocharged, direct injection engines; oxidation and reduction catalysts for diesel engine exhausts. "Selected Topics? makes recommendations for research and provides a bibliography and lists of references.

Jan 1, 1979

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981

By Paul C. McWilliams

The U.S. Bureau of Mines has, primarily through its contract program, used large-scale centrifuges to determine design criteria for tailing embankments. The centrifuge runs were made at two installations, the University of Cambridge, Cambridge, England and Sandia National Laboratories, Albuquerque, NM. The major problems considered were as follows: slope stability of embankments, modeling erosion and seepage, use of the phreatic surface level to ascertain the validity of centrifuge modeling, and the effects of compaction and weathering on a tailings embankment. This report summarizes the results of the four test series conducted at University of Cambridge and Sandia National Laboratories. A review of prior centrifuge applications to mining problems is included. Consideration is given to future centrifuge application to mining problems in both soil and rock mechanics.

Jan 1, 1989

By Llewellyn A. Rubin

Under Bureau of Mines Contract H0122007, Telcom, Inc., with the assistance of Fenix & Scisson, Inc., conducted a 17-month research and development project aimed at provid¬ing a field-test model of a guidance system for use with the Bureau of Mines Probe Drill. The Probe Drill is a part of the Bureau's Mine Rescue System developed under Contract H0101262. Volume I of this report is subdivided into seven sections. Volume II consists of a number of supporting appendices. In addition, there were delivered under the Contract, a number of other documents which are referenced in the text. Section 1 deals with essential contract information, Program Background, and a general system description. Section 2 covers the project chronology in brief. Section 3 is a digest of design considerations and implementation related to the requirements of the Contract. Section 4 is a description of the System, including illustrations of the hardware, and software. Section 5 is devoted to Operation and Maintenance. Para. 5.1 describes step-by-step field assembly and disassembly of the downhole unit. Para. 5.2 covers Operation. Para. 5.3 covers various aspects of maintenance from the lowest field echelon possible. Higher level maintenance must be accomplished in the laboratory, for the present field-test model. Para. 5.4 covers system calibration. Para. 5.5 covers detailed step-by-step operational sequences. Section 6 covers the results of the field testing, post-test evaluation, and recommendations. Essentially, we conclude that the present hardware (field-test model) has proven every aspect of system performance, but failed to provide reliable assurance of an operationally ready system. Telcom, therefore, recommends a three-phase continuing effort devised to provide the operationally-ready model of the system.

Jan 1, 1973

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

By R. O. Dannenberg

The Bureau of Mines conducted laboratory batch and small-scale continuous tests to remove traces of dissolved molybdenum from water simulating waste discharged from a molybdenum concentrator, Molybdenum concentrations, initially ranging from 2 to 10 ppm, were decreased to 0.5 ppm or less by coprecipitation of the molybdenum with freshly precipitated ferric hydroxide" The precipitate was separated as a froth by dissolved-air flotation for subsequent disposal. Although the treated water met current environmental standards for contained molybdenum, contained particulate iron might have to be removed by filtration for the water to be acceptable. Estimated costs for treating concentrator effluent water were 55 cents, 57 cents, and 64 cents per 1,000 gal at initial molybdenum concentrations of 2, 4, and 10 ppm, respectively.

Jan 1, 1982

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972

By Wilmer McInnis

MOLYBDENUM, one of the more versatile alloying elements in modern metallurgy, was first isolated by Hjelm in 1782. The pure metal is silvery white and softer than steel. It melts at a higher temperature than all other metals except rhenium, tungsten, and tantalum. Molybdenum, a member of group V of the periodic table, chemically exhibits valences in stable compounds of 2, 3, 4, 5, and 6. It is a strong carbide-forming element, and much of its alloying effect in steel is imparted through the formation of carbides. Molybdenum occurs in nature only in combination with other elements. The most common occurence is molybdenite (MoS2), which is widely distributed throughout the world; the few known commercial deposits are the major sources of molybdenun1. The other commercially important mineral, wulfenite (PbMo04), was a major source of molybdenum in the United States during the early part of the 20th century, but with exploration and development of the world-famous Climax molybdenite deposit during the World War of 1914-18, molybdenite soon became the world's major source of molybdenum. In recent years, virtually no wulfenite has been mined. Many copper deposits contain minute percentages of molybdenite; and, since the inauguration during the early 1930's of the recovery of molybdenite as a byproduct of these deposits, they have been an important source of molybdenum.

Jan 1, 1957

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By Robert W. Geehan

The Bureau of Mines developed, by core drilling, the property of Nevada Scheelite, Inc., from October 5, 1943, to February 24, 1944. Claims of the corporation are near Rawhide in the northern portion of Mineral County, Nev. The purpose of the work was to determine possible reserves in the lateral and vertical extensions of a tactite zone which was being mined for scheelite. Production from this zone to January 1, 1944, was said to be 64,500 tons, with a recovery of 50,618 units of tungsten trioxide. The development work was done by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, mapping the areas, and exploring the deposit by diamond drilling, trenching and sampling. Eleven holes were drilled for a total footage of 2,365 feet of holes.

Jan 1, 1950